UMD-606N
11n Micro Dongle
User Guide
Index
1. Product Overview......... ......................................................................................................... 3
1.1. Introduction................................................................................................................3
1.2. Product Appearance................................................................................................. 3
2. Installation................................................................................................ .............................. 4
2.1. Installing the Software of the Micro USB adapter.............................................. 4
3. Connect to Internet- Station Mode................................ ..................................................... 7
3.1. Setup in Wireless Utility....................................................................................... ... 7
3.2. Setup Wireless LAN with WPS PBC...................................................................... 9
3.3. Setup Wireless LAN with WPS PIN........ ..............................................................10
4. Connect to WiFi Devices- AP Mode........................................... ...................................... 12
Troubleshooting...... ..................................................................................................................... 14
Solwise Ltd UMD-606N Page
3
1. Product Overview
1.1.
Introduction
The UMD-606N Micro 802.11n USB Adapter is, in our opinion, the world’s smallest wireless
adapter which provides a simple (physical WPS button) and secure (64/128bit WEP, WPA,
WPA2 WLAN security) way to enable 150M 802.1n wireless access to your notebook or
desktop computer.
It uses the latest Green WLAN technology, which controls power consumption automatically in
accordance with WLAN activities. No setting is required for this function. This Micro USB
Adapter can save up to 80% power consumption compared with legacy 802.11n products.
1.2.
Product Appearance
LED Status Description
LINK/ACT
On Wireless USB dongle is powered on.
Off Wireless USB dongle is powered off.
Solwise Ltd UMD-606N Page
4
2. Installation
Describes the procedure for installing the UMD-606N.
2.1.
Installing the Software of the Micro USB adapter
(1). Don’t insert the Micro-dongle yet. First of all insert the product CD in to your PC.
The CD should auto-run. At the welcome screen, please click Driver to install the driver
and utility.
If you don’t see the welcome screen, go to Start My Computer and click to open
CD-ROM drive. Then double click autorun.exe and wait for few seconds, the welcome
screen will show up.
Click “Next”.
Click “Install” to start the
setup program.
Solwise Ltd UMD-606N Page
5
Waiting for system running.
(2). Restart your computer
Once the installation is
finished, click Finish to
restart you computer.
(3). Connect the USB Adapter
Now plug the Micro Adapter
into USB adapter on your
Laptop or Desktop computer.
(4). Check the Wireless Connection
Double click on Wireless Utility icon in the system tray or on the desktop.
Icon in System Tray Utility icon on Desktop
Solwise Ltd UMD-606N Page
6
Click on the Available Network tab to view
all the access points with the range of this
adapter. Double click on the SSID that you
want to connect.
If the wireless network you selected
requires security, the utility will guide
through the appropriate security setup.
After the signal strength is indicated, you
have successfully set up your wireless
network on you PC or Laptop.
Solwise Ltd UMD-606N Page
7
3. Connect to Internet-Station Mode
Used as client to connect to an access point such as wireless LAN router.
The UMD-606N has 3 setup methods.
3.1.
Setup in Wireless Utility
Below illustrates how to select and connect to an access point through the installed Wireless
Utility.
(1). Check your wireless LAN setting information.
Check the access point setting information and take note as list below.
Name Information set in the wireless router/access point
SSID
(Connection name)
Encryption type Authentication type
WEP Open System / Share Key / Auto
WPA /WPA2/
WPA2 Mixed
AES / TKIP
Network key
(the Encryption key of the access point)
(2). Select Access Point
Solwise Ltd UMD-606N Page
8
Make sure the Micro Adapter is under
“Station Mode”.
Click on Available Network tab to find the
access points and double click on its SSID.
If the access point you are connecting is not
in the list, click “Refresh” to renew the list.
The Security setting window will show up if
the access point requires security.
Enter the information you checked from the
access point and click “OK”.
Solwise Ltd UMD-606N Page
9
You can check General information once the
wireless network connected successfully.
3.2.
Setup Wireless LAN with WPS PBC
If your wireless router /access point is WPS supported, you can make the connection by just
pressing the WPS button.
Press the WPS button on your wireless
router/ access point to enable the WPS
paring. Then release the button when
the WPS LED is lit.
Then you need press the WPS button on
the Micro adapter.
(If you can not press WPS button with
your fingers, please press it with
something sharp, e.g. a pen).
When the setup window shows up,
releasing the button.
Solwise Ltd UMD-606N Page
10
You can check General information once
the WPS connection is established.
3.3.
Setup Wireless LAN with WPS PIN
Setup the wireless LAN with a PIN code if the wireless router /access point supports WPS PIN
function.
Open the Wireless Utility of Micro
adapter and click the Wi-Fi
Protect Setup.
Write down the PIN code and
press the “Pin Input Config
(PIN)”.
Select a specific access point by
click Yes.
Solwise Ltd UMD-606N Page
11
Click on the SSID which you
want to connect.
If the access point you are
connecting is not in the list, click
“Refresh” to renew the list
The Micro Adapter is waiting for
the connection with your
selected Access Point.
Meanwhile, open the Access
Point’s setup page and input the
PIN code.
You can check General
information once the connection
is established.
Solwise Ltd UMD-606N Page
12
4. Connect to WiFi Devices- AP Mode
Use the UMD-606N as a wireless access point, and you can create direct WiFi links with other
WiFi supported devices such as gaming machines or a mobile phone.
(1). Switch the Mode type to Access Point
Select Access Point mode and wait for
the system changed.
Solwise Ltd UMD-606N Page
13
Select the Internet connection you want to
share and the Wi-Fi security setting to use
for access point will be displayed.
Using you WiFi device to search for WiFi
Connection. You can find the AP in the
WiFi Networks.
Solwise Ltd UMD-606N Page
14
Troubleshooting
Problem Corrective Action
None of the LEDs turn on
when I plug in the wireless
USB adapter.
Make sure you have turned on your computer
Check the utility and driver for your WLAN adapter have
installed correctly.
Restart your computer and plug in the adapter again.
Make sure there is no hardware conflict and check your
computer resource information.
Cannot access the
configuration utility.
Make sure the WLAN adapter is installed / plugged in
properly.
Check the utility version you have installed is correct.
I cannot connect to a
wireless network
Make sure the ACT LED on the WLAN adapter is blinking.
Check the wireless router is within range and move your
computer closer to the wireless router.
Make sure that you have set the wireless network settings
correctly. For example, the SSID and security settings.
Make sure there is no radio interference (for example,
cordless phones, microwave oven, etc) that may affect
wireless transmission quality.
European Union Statement of Compliance
It is hereby declared that this wireless dongle is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
Loading...