Version 1.0
1
3GWIFIMRD
3.5G plus WLAN Desktop Server Router
User Manual
Version 1.0
2
Table of Content
SAFE SEATING GESTURES ........................................................................................................................... 8
CHAPTER 1 INTRODUCTION ........................................................................................................................ 9
1.1 OVERVIEW.............................................................................................................................. 9
1.2 FEATURES ............................................................................................................................ 10
1.3 SPECIFICATIONS ....................................................................................................................11
1.3.1 FRONT PANEL AND LED INDICATORS DESCRIPTION................................................................ 12
1.4 SYSTEM REQUIREMENTS....................................................................................................... 12
1.5 GET YOUR IP AUTOMATICALLY & MANUALLY ......................................................................... 12
1.5.1 Network Testing .............................................................................. 16
CHAPTER 2 HARDWARE INSTALLATION ............................................................................................... 19
2.1 DIAGRAM OF CONNECTING HARDWARE TO 3.5G PLUS WLAN MOBILE SERVER ROUTER......... 19
2.1.1 Router Mode Hardware Connection and Application................................ 19
2.1.2 AP Mode Hardware Connection and Application..................................... 20
2.1.3 Client Mode Hardware Connection and Application ................................. 20
CHAPTER 3 ROUTER MODE ....................................................................................................................... 21
3.1 ADMINISTRATOR QUICK SETUP INSTRUCTION ......................................................................... 21
3.2 OPERATION MODE ................................................................................................................ 22
3.3 QUICK SETUP ....................................................................................................................... 23
3.3.1 WAN Setup (Internet Connection)........................................................ 25
3.3.2 LAN Setup ..................................................................................... 33
3.3.3 Wireless Setup................................................................................ 33
3.3.4 Time Server Setup ........................................................................... 35
3.3.5 Password Setup .............................................................................. 35
3.3.6 USB Disk Management Setup ............................................................. 36
3.3.7 User Account Management Setup ....................................................... 36
3.3.8 Firewall Setup................................................................................. 37
3.3.9 QoS Configuration Setup .................................................................. 38
3.3.10 FTP Server Setup ............................................................................ 39
3.3.11 Printer Server Setup......................................................................... 39
3.3.12 Web Camera Server Setup ................................................................. 40
3.3.13 Samba Server Setup ........................................................................ 40
3.3.14 Quick Setup Finish .......................................................................... 41
3.4 IP CONFIGURATION ............................................................................................................... 41
3.4.1 WAN ............................................................................................. 41
Version 1.0
3
3.4.2 LAN.............................................................................................. 50
3.4.3 Wireless ........................................................................................ 51
3.4.4 DDNS............................................................................................ 55
3.5 ADVANCED ........................................................................................................................... 56
3.5.1 NAT .............................................................................................. 57
3.5.2 Firewall ......................................................................................... 59
3.5.3 QoS.............................................................................................. 67
3.6 SERVER................................................................................................................................ 68
3.6.1 Samba Server ................................................................................. 68
3.6.2 FTP Server ..................................................................................... 71
3.6.3 Web Camera Server ......................................................................... 72
3.6.4 Printer Server ................................................................................. 80
3.7 SYSTEM MANAGEMENT ......................................................................................................... 88
3.7.1 Reboot .......................................................................................... 88
3.7.2 Change Password ........................................................................... 88
3.7.3 Firmware Upgrade ........................................................................... 89
3.7.4 Profile Sasve .................................................................................. 90
3.7.5 Remote Management........................................................................ 91
3.7.6 Time ............................................................................................. 93
3.7.7 UPnP Setting .................................................................................. 94
3.7.8 User Account Management ................................................................ 94
3.7.9 Folder Management ......................................................................... 96
3.7.10 Email Alert ..................................................................................... 97
3.8 LOG & STATUS ..................................................................................................................... 99
3.8.1 Network Configuration...................................................................... 99
3.8.2 User Account List.......................................................................... 100
3.8.3 Event Log .................................................................................... 101
3.9 LOGOUT ............................................................................................................................. 101
3.10 PERSONAL CONFIGURATION ................................................................................................ 101
3.10.1 Anonymous ................................................................................. 103
3.10.2 My Document ............................................................................... 104
3.10.3 My Webcam.................................................................................. 105
3.10.4 My Status..................................................................................... 105
3.11 SITE MAP ........................................................................................................................... 106
CHAPTER 4 AP MODE ................................................................................................................................. 107
4.1 ADMINISTRATOR QUICK SETUP INSTRUCTION ....................................................................... 107
4.2 OPERATION MODE .............................................................................................................. 108
Version 1.0
4
4.3 QUICK SETUP ..................................................................................................................... 109
4.3.1 LAN Setup ................................................................................... 111
4.3.2 Wireless Setup.............................................................................. 112
4.3.3 Time Server Setup ......................................................................... 114
4.3.4 Password Setup ............................................................................ 114
4.3.5 USB Disk Management Setup ........................................................... 114
4.3.6 User Account Management Setup ..................................................... 115
4.3.7 FTP Server Setup .......................................................................... 116
4.3.8 Printer Server Setup....................................................................... 117
4.3.9 Web Camera Server Setup ............................................................... 117
4.3.10 Samba Server Setup ...................................................................... 117
4.3.11 Quick Setup Finish ........................................................................ 118
4.4 IP CONFIGURATION ..............................................................................................................118
4.4.1 LAN............................................................................................ 118
4.4.2 Wireless ...................................................................................... 120
4.5 SERVER.............................................................................................................................. 124
4.5.1 Samba Server ............................................................................... 125
4.5.2 FTP Server ................................................................................... 127
4.5.3 Web Camera Server ....................................................................... 128
4.5.4 Printer Server ............................................................................... 137
4.6 SYSTEM MANAGEMENT ....................................................................................................... 143
4.6.1 Reboot ........................................................................................ 143
4.6.2 Change Password ......................................................................... 143
4.6.3 Firmware Upgrade ......................................................................... 144
4.6.4 Profile Save.................................................................................. 145
4.6.5 Remote Management...................................................................... 146
4.6.6 Time ........................................................................................... 147
4.6.7 UPnP Setting ................................................................................ 147
4.6.8 User Account Management .............................................................. 148
4.6.9 Folder Management ....................................................................... 149
4.6.10 Email Alert ................................................................................... 150
4.7 LOG & STATUS ................................................................................................................... 152
4.7.1 Network Configuration.................................................................... 152
4.7.2 User Account List.......................................................................... 153
4.7.3 Event Log .................................................................................... 154
4.8 LOGOUT ............................................................................................................................. 154
4.9 PERSONAL CONFIGURATION ................................................................................................ 154
4.9.1 Anonymous ................................................................................. 156
Version 1.0
5
4.9.2 My Document ............................................................................... 157
4.9.3 My Webcam.................................................................................. 158
4.9.4 My Status..................................................................................... 158
4.10 SITE MAP ........................................................................................................................... 159
CHAPTER 5 CLIENT MODE ....................................................................................................................... 160
5.1 ADMINISTRATOR QUICK SETUP............................................................................................ 160
5.2 OPERATION MODE .............................................................................................................. 161
5.3 QUICK SETUP ..................................................................................................................... 162
5.3.1 SITE SURVEY SETUP........................................................................................................... 163
5.3.2 Wireless Setup.............................................................................. 164
5.3.3 Time Server Setup ......................................................................... 164
5.3.4 Password Setup ............................................................................ 165
5.3.5 USB Disk Management Setup ........................................................... 165
5.3.6 User Account Management Setup ..................................................... 166
5.3.7 FTP Server Setup .......................................................................... 166
5.3.8 Web Camera Server Setup ............................................................... 167
5.3.9 Printer Server Setup....................................................................... 167
5.3.10 Samba Server Setup ...................................................................... 168
5.3.11 Quick Setup Finish ........................................................................ 168
5.4 IP CONFIGURATION ............................................................................................................. 169
5.4.1 LAN............................................................................................ 169
5.4.2 Site Survey .................................................................................. 170
5.5 SERVER.............................................................................................................................. 172
5.5.1 Samba Server ............................................................................... 172
5.5.2 FTP Server ................................................................................... 175
5.5.3 Web Camera Server ....................................................................... 176
5.5.4 Printer Server ............................................................................... 184
5.6 SYSTEM MANAGEMENT ....................................................................................................... 191
5.6.1 Reboot ........................................................................................ 191
5.6.2 Change Password ......................................................................... 191
5.6.3 Firmware Upgrade ......................................................................... 192
5.6.4 Profile Save.................................................................................. 193
5.6.5 Remote Management...................................................................... 194
5.6.6 Time ........................................................................................... 195
5.6.7 UPnP Setting ................................................................................ 196
5.6.8 User Account Management .............................................................. 196
5.6.9 Folder Management ....................................................................... 198
Version 1.0
6
5.6.10 Email Alert ................................................................................... 199
5.7 LOG & STATUS ................................................................................................................... 200
5.7.1 Network Configuration.................................................................... 200
5.7.2 User Account List.......................................................................... 201
5.7.3 Event Log .................................................................................... 201
5.8 LOGOUT ............................................................................................................................. 202
5.9 PERSONAL CONFIGURATION ................................................................................................ 202
5.9.1 Anonymous ................................................................................. 204
5.9.2 My Document ............................................................................... 205
5.9.3 My Webcam.................................................................................. 206
5.9.4 My Status..................................................................................... 206
5.10 SITE MAP ........................................................................................................................... 207
CHAPTER 6 DDNS SERVICE APPLICATION .......................................................................................... 208
CHAPTER 7 Q & A......................................................................................................................................... 213
7.1 INSTALLATION .......................................................................................................................... 213
7.2 LED 213
7.3 IP ADDRESS ............................................................................................................................ 214
7.4 OS SETTING ............................................................................................................................ 214
7.5 3.5G PLUS WLAN MOBILE SERVER ROUTER SETUP................................................................. 216
7.6 WIRELESS LAN ....................................................................................................................... 218
7.7 SAMBA SERVER ....................................................................................................................... 221
7.8 USB FTP SERVER................................................................................................................... 221
7.9 WEBCAM SERVER.................................................................................................................... 222
7.10 PRINTER SERVER................................................................................................................... 223
7.11 SUPPORT............................................................................................................................... 223
7.12 OTHERS ................................................................................................................................ 224
7.13 USB DEVICE ......................................................................................................................... 224
CHAPTER 8 APPENDICES .......................................................................................................................... 225
8.1 PRINTER............................................................................................................................. 225
8.2 WEB CAMERA..................................................................................................................... 225
8.3 USB DEVICES .................................................................................................................... 230
8.4 OPERATING SYSTEMS ......................................................................................................... 231
8.5 BROWSERS ........................................................................................................................ 231
8.6 EASY SETUP....................................................................................................................... 231
8.7 COMMUNICATIONS REGULATION INFORMATION ..................................................................... 231
Version 1.0
7
CE Statement of Conformity
This product has been tested in typical configuration by Ecom Sertech Corp and was found
to comply with the essential requirement of “Council Directive on the Approximation of the
Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC;
92/31/EEC; 93/68/EEC)
Marking by the above symbol indicates compliance with the Essential Requirements of the
R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following
conformance standards:
EN300 328, EN301 489-17, EN60950
Countries of Operation and Conditions of Use in the European Community
This device is intends to be operated in all countries of the European Community.
Requirement is for indoors vs. outdoors operation, license requirements and allowed
channels of operation apply in some countries as described in this document.
Note: The user must use the configuration utility provided with this product to check
the current channel of operation and confirm that the devices operating in
conformance with the spectrum usage rules for the European Community countries as
described below.
If operation is occurring outside of the allowable channels as indicated in this guide, then
the user must cease operating the product and consult with the local technical support staff
responsible for the wireless network.
This device may be operated indoors or outdoors in all countries of the European
Community using the 2.4GHz band: Channels 1 – 13, except where noted below:
· In Italy the end-user must apply for a license from the national spectrum authority to
operate this device outdoors.
· In France outdoor operation is only permitted using the 2.4 – 2.454 GHz band:
Channels 1 – 7.
Version 1.0
8
Safe Seating Gestures
You should follow the manufacturer’s instructions for adjusting the backrest to fit your body
properly.
An adjustable chair that provides firm, comfortable support is best.
Adjust the height of the chair so your thighs are horizontal and your feet flat on the
floor.
The back of the chair should support your lower back (lumbar region).
Version 1.0
9
Chapter 1 Introduction
1.1 Overview
3.5G plus WLAN Mobile Server Router is a portable and convenient wireless solution for
delivering 802.11g wireless connectivity with a maximum wireless signal rate of up to
54Mbps. Use it in conference rooms, hotel rooms, or even at hotspots. The unit supports
multiple operation modes, including Access Point (AP) mode, Router mode, and Wireless
Client mode. You can switch among these modes easily by manually applying 3.5G plus
WLAN Mobile Server Router's 3-way configuration software switch. In addition to, there
are 2 USB ports available for connecting any devices which allow LAN users to utilize
shared printer and samba server. Also, apply 3.5G plus WLAN Mobile Server Router with a
Webcam to monitor in real time, or with a USB-connected Flash/Drive to become a FTP
server providing shared download service in the mean time.
In other words, monitor your home with a Webcam by taking pictures via 3.5G plus Mobile
Server Router and record all images into the USB HDD for reviewing. Often marketed as
surveillance tools for home or office security, network Webcams are now being employed by
early adopters for more personal matters, such as watching kids and monitoring pets. The
Webcam can be remotely accessed and controlled via a browser. Moreover, while
connectting 3.5G plus WLAN Mobile Server Router with 3.5G USB dongle/Card Bus to
access Internet or work as connection backup, you can immediately speed up data
transmission, as well as calling out and receiving phone calls via a cell phone.
Version 1.0
10
1.2 Features
3.5G plus WLAN Mobile Server Router’s main functions, including Wireless Access, Printer
Server, Webcam Monitor, Samba Server, FTP Server and IP Sharing etc. are shown as
below. These features and their applying instructions specified in User Manual will not only
fulfill your requirements, but also ease your inconvenience from the job.
Easy Setup
Proprietary utility is designed to let users, even the beginners, complete their server setups
easily and access Internet without any difficulty.
3 Operation Modes
The unit provides Router, AP and Client operation modes by manually exchange via
software.
Web GUI
Friendly user interface only requires supported web browser to start advanced setup.
Webcam Server
The product supports USB Web Camera, which provides easy and affordable solution for
home safety. It allows users monitoring home from anywhere via online webcam. Also, you
might be alerted by an email with an intruder picture.
Samba Server
It is located on your network places to provide shared information and printer for LAN users.
FTP Server
3.5G plus WLAN Mobile Server Router supports FAT32/EXT3 file system format. Plug with
USB hard drive or thumb drive, it will become a FTP server, and the users can share files on
the Internet.
Printer Server
3.5G plus WLAN Mobile Server Router supports LPR protocol, so users can use shared
printer from both WAN and LAN.
Security/Encryption
The unit is equipped with encryption types of WEP, WPA, 802.1x and so on to give more
security assurance.
Real-time Monitoring
3.5G plus WLAN Mobile Server Router can save real-time images from connected web
camera for the purpose of home safety monitoring.
3.5G Internet Connection
With a 3.5G USB dongle/Card Bus, 3.5G plus WLAN Mobile Server Router can upgrade its
data transmission rate on the Internet.
Version 1.0
11
1.3 Specifications
CPU Star 9105gu
Flash ROM 8Mbyte (NAND Gate)
Components
DRAM 32MByte
WAN Port 1 x 10/100 Mbps RJ45, with auto MDI/MDIX
LAN Port 4 x 10/100 Mbps RJ45, with auto MDI/MDIX
USB2.0 Port
2 x Standard _A type—USB 2.0 for 3.5G USB Dongle, USB Webcam,
USB printer, USB Flash/HDD
Wireless Ralink 2561 Mini_PCI
Card Bus
1 x Card Bus slot for 3.5G device, support Qualcomm MSM6280 and 7200
chipsets (Sierra Wireless Aircard 875 and 880)
Interface
Software Switch Manually exchange among Router/AP/Client operation modes.
Web-Base Windows IE / Linux Firefox / MAC Safari
WAN Protocol PPPoE / PPTP / Static IP/ Dynamic IP/ HSDPA/UMTS
WLAN WDS / WEP Key / WPA / WPA-PSK / MAC Access Control /Hidden SSID
Routing UPnP / DHCP / DNS / WINS / DDNS
NAT Virtual Server / Virtual DMZ
Firewall MAC Filter / URL Filter / SPI / DoS Protection / IP Packet Filter
QoS 3-level priority for each application port
Folder
Management
Disk Format
Function
User account
Management
User account create and access control
Webcam Server
Webcam view via browser by internet real time
Picture monitor from LAN/WAN PC
Picture recording to FTP server or USB HDD
Printer Server
Printer Via WAN/LAN PC
Printer Sharing
Samba Server File Sharing
Application
Management
FTP Server Anonymous login / User login
Administrator
Quick Setup Wizard / Site Map
Setup wizard / General Setup
Personal Panel My Document / My Webcam / My Status
Operation
Requirement
Operating Temp. 0°C~40°C (32°F~104°F)
Storage Temp. -20°C~70°C (-14°F~158°F)
Operating Humidity 10% to 85% Non-Condensing
Storage Humidity 5% to 90% Non-Condensing
Peak Gain of the
Antenna
2dBi @ 2.45GHz
Transmitted
Power (Typical)
15dBm @ Normal Temp. Range
Others
Receive
Sensitivity (Typical)
Normal Temp. Range: 11Mbps: 10-5 BER @ -83 dBm
Dimension 225mm (L) x 162mm (W) x 48mm (H)
Application
Power Adapt AC 100 V ~ 240 V in / DC 5V 2.5A output
Notice: USB devices with power more than 0.5 mAh are not supported.
Notice: Firmware Upgrade available through download.
Version 1.0
12
1.3.1 Front Panel and LED Indicators Description
Status
LED Indicator
Solid Flashing
WIRELESS
Operation OK Transmitting Data
LAN Ethernet OK Transmitting Data
WAN
Internet OK Transmitting Data
STATUS Operation OK Reset/Firmware updates in progress
POWER
Operation OK Firmware upgrade failed
1.4 System Requirements
To begin with 3.5G plus WLAN Mobile Server Router, you must have the following minimum
system requirements. If your system can’t correspond to the following requirements, you
might get some unknown troubles on your system.
XDSL/Cable Modem and broadband Internet Account.
One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card.
TCP/IP and at least one web browser software installed (E.g.: Internet Explorer 5.0,
Netscape Navigator 7.x, Apple Safari 2.03 or higher version).
At lease one 802.11g (54Mbps) or one 802.11b (11Mbps) wireless adapter for wireless
mobile clients.
Recommended OS: Win2000 or WinXP / Linux.
1.5 Get Your IP Automatically & Manually
After 3.5G plus WLAN Mobile Server Router connected with your computer, please make
sure your IP is in the automatic IP position or you adjust it manually in order to activate the
Internet network from home to Internet. If you don’t know how to enter the settings, please
follow the steps as below.
Version 1.0
13
【【【【Step 1】】】】
Go to Start>Settings> Network Connections and then select Local Area Connection.
【【【【Step 2】】】】
Click on Properties
Version 1.0
14
【【【【Step 3】】】】
Double click on Internet Protocol (TCP/IP).
【【【【Step 4-1】】】】
For getting IP automatically if you are one of the users under 3.5G plus WLAN Mobile
Server Router, please skip Use the following IP address and then select Obtain an IP
address automatically and Obtain DNS server address automatically and then click on
OK button.
【【【【Step 4-2】】】】
For getting IP manually in order to specify a Virtual Server, such as Print Server, FTP Server
Version 1.0
15
and so on, please skip Obtain an IP address automatically and then select Use the
following IP address. And the following default setting of 3.5G plus WLAN Mobile Server
Router should be noted:
IP Address：192.168.1.10 (as your Print Server for example)
Subnet Mask：255.255.255.0
Default Gateway：192.168.1.1
Notice: If you configure your computer’s IP Address manually, it needs to be on the same
network segment.
For example:
IP Address: 192.168.1.xxx (xxx can be any number between 2 and 253, but it can’t be
repeated, we use 100 to be the example.)
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1 (this is the IP address of 3.5G plus WLAN Mobile Server Router
in Router Mode)
DNS: 192.168.1.1 (use 3.5G plus WLAN Mobile Server Router’s IP address or on your
own choice)
Notice: IP address and Default gateway cannot be the same.
Version 1.0
16
1.5.1 Network Testing
There are two ways to test your Network whether it can work on Internet or not. They are
“Testing with Internet Browser” and “Testing with Dos”.
1.5.1.1 Testing with Internet Browser
Open an Internet Browser, such as Internet Explore or Netscape. Input a valid web
address you like, for example, http://www.yahoo.com in the web address blank and then
press enter. If the website appears, that means your Internet is working under normal
situation.
Version 1.0
17
1.5.1.2 Testing with DOS (Windows XP Platform)
【【【【Step 1】】】】
Go to start > Run.
【【【【Step 2】】】】
Input cmd in the blank, and then click OK button. The Command Prompt window appears.
【【【【Step 3】】】】
Input ipconfig in the flashing area then press enter. You will get an IP Address
192.168.1.100, for example, and Default Gateway as 192.168.1.1.
【【【【Step 4】】】】
Ping a legal WAN Address such as 192.168.1.1. If Internet works, it will show Reply from
192.168.1.1: bytes = 32 time = 3ms TTL =64, for example.
Version 1.0
18
If it can’t work, it will show Request timed out.
19 Version 1.0
Chapter 2 Hardware Installation
2.1 Diagram of Connecting Hardware to 3.5G plus WLAN Mobile Server Router
3.5G plus WLAN Mobile Server Router is a portable and convenient wireless solution for the
traveling businessmen delivering 802.11g wireless connectivity with a maximum wireless
signal rate of up to 54Mbps. Use it in conference rooms, hotel rooms, or even at hotspots.
The Router supports multiple operation modes, including Access Point (AP) mode, Router
mode, and Wireless Client mode. You can switch among these modes easily by manually
applying 3.5G plus WLAN Mobile Server Router's 3-way configuration software switch.
Moreover, there are 2 USB ports support with 3.5G plus WLAN Mobile Server Router; user
can plug the USB devices including Flash Disk, Web Camera, Printer or 3.5G USB Dongle.
2.1.1 Router Mode Hardware Connection and Application
When 3.5G plus WLAN Mobile Server Router switches to Router Mode, there will be WAN
and LAN ports existing, the administrator can do the Quick Setup including WAN Setup,
LAN Setup, Wireless Setup, Time Server Setup, Password Setup, USB Disk Management
Setup, User Account Management Setup, Firewall Setup, QoS Setup, FTP Server Setup,
Web Camera Setup, Print Server Setup and Samba Server Setup.
20 Version 1.0
2.1.2 AP Mode Hardware Connection and Application
Under AP Mode, it supports LAN ports as Bridge, and user can connect to 3.5G plus WLAN
Mobile Server Router via LAN port or Wireless (WDS). The administrator can set up quickly,
including LAN Setup, Wireless Setup, Time Server Setup, Password Setup, USB Disk
Management Setup, User Account Management Setup, FTP Server Setup, Web Camera
Setup, Printer Server Setup and Samba Setup.
2.1.3 Client Mode Hardware Connection and Application
As for Client Mode, 3.5G plus WLAN Mobile Server Router will be a Wireless Adapter, and
users can plug cable to each LAN port and then connect Internet via Wireless.
21 Version 1.0
Chapter 3 Router Mode
3.1 Administrator Quick Setup Instruction
Make sure that 3.5G plus WLAN Mobile Server Router is in Router Mode from IP
configuration, then open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
browser, and enter
http://192.168.1.1 (Default Gateway) into browser’s blank.
Notice: If the homepage doesn’t appear, please check if the TCP/IP configuration is obtaining IP address
automatically or not. If you don’t know how to do it, please refer to “1.5 Get your IP Automatically
& Manually”.
Homepage
Please click on Administrator button to log in setup at first time, also any settings can be
changed in the future. Only the Administrator has the right to modify all settings.
22 Version 1.0
User Name and Password
The default values for User Name and Password are admin (all in lowercase letters). Click
Login to enter.
Notice: Only the password can be changed, please read setup “3.3.5 Password Setup” or “3.7.2 Change
Password”. In order to protect your own settings, it’s strongly recommended to change the password
before you finish the Router Basic Setup.
3.2 Operation Mode
Click on Operation Mode from the left menu. After logging in, user can manually switch to
other 2 modes by selecting the preferred and click Apply.
A message window will pop up for your confirmation to reboot the system. Click OK to
continue.
23 Version 1.0
3.3 Quick Setup
Typical Configuration Manager Page consists of two separate frames. The left frame
contains all the means available for device configuration. Menus are indicated by file icons,
and related menus are grouped into categories, such as LAN, WAN etc., and indicated by
folder icon, depending on whether the group of menus are expanded or not. You can click
on any of these to display a specific configuration page. And the right frame is designed
as a site map. And the right frame is designed as a site map.
The above diagram shows all PCs and devices connected to your 3.5G plus WLAN
Mobile Server Router and their status. Click Quick Setup on the left of the main menu.
Then you’ll see the full functionality selection screen appears and detailed settings for
each item, including “Basic” and “Application” two parts.
Note: The device models named of USB Device, Webcam and Printer will be shown under the picture of each
device if the product supports.
Quick Setup full function table list
24 Version 1.0
Click Basic, you see 5 major items set in Quick Setup Selection. Please click Next
button after confirmed.
Click Application, you see 8 major items set here, including USB Disk Management
Setup, User Account Management Setup, Firewall Setup, QoS Setup, FTP Server Setup,
Printer Server Setup, Web Camera Setup and Samba Server Setup. For the checked
ones are recommended, all can be selected upon your demands.
Quick Setup Instruction
WAN Setup: Set up the connecting type provided by your ISP, 5 modes of WAN
connection are supported by 3.5G plus WLAN Mobile Server Router–Static IP,
Dynamic IP, PPPoE, PPTP and HSDPA/UMTS.
LAN Setup: Set up the IP Address for LAN and Group. If you are using the Router
with multiple PCs on your LAN, you must connect the LAN via the Ethernet ports on
the built-in Ethernet switch. You should also assign a unique IP address to each
device residing on your LAN.
Initiated as default
Initiated as default
25 Version 1.0
Wireless Setup: Define the Wireless Mode, ESSID, TxRate, Channel and other
wireless settings.
Time Server Setup: Set time by NTP server or user defines.
Password Setup: To change administrator’s password.
USB Disk Management Setup: View the entire data folder inside each storage
devices, also can do formatting and disk partition.
User Account Management Setup: Set maximum user number, account and right for
using personal services of your 3.5G plus WLAN Mobile Server Router for each user.
Firewall Setup: To enable Firewall and set security level.
QoS Setup: To enable/disable QoS setup.
FTP Server Setup: To enable FTP server and set controlling rules.
Printer Server Setup: To enable /disable server.
Web Camera Setup: To enable Web camera function.
Samba Server Setup: To enable Samba server for shared documents and printer.
3.3.1 WAN Setup (Internet Connection)
WAN is short for Wide Area Network. The WAN settings can be referred to as the Public
setting. All IP information in the WAN settings is public IP addresses which are accessible
on the Internet. 3.5G plus WLAN Mobile Server Router supports 5 connection types to
WAN. Select one of the WAN connection modes required by your ISP in the following
Internet Connection Configuration page, the WAN setup pages will vary depending on
what kind of WAN Type you select.
Choose your WAN type as the above mentioned, and its associated settings will show up
underneath at the same time.
3.3.1.1 WAN Type – Static IP
26 Version 1.0
Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will
need to enter the IP address, IP Netmask and IP gateway as provided. Each entered fields
must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The
Router will not accept the IP address if it is not in this format. If ISP provides you DNS
information, please select Specify DNS Server IP and fill in Primary field at least;
otherwise, Domain Name can’t be used.
In particular, here provides 3G or 3.5G transmission rate when the device is plugged, either
a 3.5G USB Dongle or Card Bus; just check to apply for the backup. In other words, once
Static IP connection is disconnected, the system automatically connects Internet via 3.5G
adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals
until none existed. The default interval between the two connection detection is 3 minutes.
The interval range is from 1 to 3 minutes.
The 3.5G feature is working as mutual backup for other 4 WAN Types, and the required
information is listed as follows, such as user name, password and SIM PIN etc. That is,
setting up the interval time to auto detect whether the Internet connection is lost or not. If
yes, the system immediately switches to 3.5G Internet connection until the original Static IP
connection is back during the next detection.
Check to activate
27 Version 1.0
Please click on Next button to go on 3.3.2 LAN Setup.
3.3.1.2 WAN Type – Dynamic IP
Choose Dynamic IP to obtain IP address information automatically from your ISP. Select
this option if your ISP does not give you any IP numbers to use. This option is commonly
used for Cable modem services. If ISP provided you DNS information, please select
Specify DNS Server IP; otherwise, select No Default DNS Server.
In particular, here provides 3G or 3.5G transmission rate when the device is plugged, either
a 3.5G USB Dongle or Card Bus; just check to apply for the backup. In other words, once
Dynamic IP connection is disconnected, the system automatically connects Internet via
3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G
signals until none existed. The default interval between the two connection detection is 3
minutes. The interval range is from 1 to 3 minutes.
The 3.5G feature is working as mutual backup for other 4 WAN Types, and the required
information is listed as follows, such as user name, password and SIM PIN etc. That is,
setting up the interval time to auto detect whether the Internet connection is lost or not. If
yes, the system immediately switches to 3.5G Internet connection until the original Dynamic
IP connection is back during the next detection.
28 Version 1.0
Click on Next button to go on 3.3.2 LAN Setup.
3.3.1.3 WAN Type – PPPoE
This option is typically used for DSL services. Choose PPPoE (Point to Point Protocol
over Ethernet) if your ISP uses PPPoE connection. Your ISP will provide you with a
username and password. MTU stands for Maximum Transmission Unit. For PPPoE
connections, you may need to change the MTU setting in order to work correctly with your
ISP. As Idle Time, it’s the amount of time of inactivity before disconnecting your PPPoE
session. Enter an Idle Time (in minutes) to define and period of time for which the Internet
connection is maintained during inactivity. If the Auto-reconnect enabled, the Router will
automatically connect to your ISP after your system is restarted, or if the connection is
dropped. If ISP provides you DNS information, please select Specify DNS Server IP;
otherwise, select No Default DNS Server.
In particular, here provides 3G or 3.5G transmission rate when the device is plugged, either
a 3.5G USB Dongle or Card Bus; just check to apply for the backup. In other words, once
Input it if requested by your ISP (Ex:
Wireless Mobile
Router)
MAC address
29 Version 1.0
Dynamic IP connection is disconnected, the system automatically connects Internet via
3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G
signals until none existed. The default interval between the two connection detection is 3
minutes. The interval range is from 1 to 3 minutes.
The 3.5G feature is working as mutual backup for other 4 WAN Types, and the required
information is listed as follows, such as user name, password and SIM PIN etc. That is,
setting up the interval time to auto detect whether the Internet connection is lost or not. If
yes, the system immediately switches to 3.5G Internet connection until the original PPoE
connection is back during the next detection.
Click on Next button to go on 3.3.2 LAN Setup.
3.3.1.4 WAN Type – PPTP
This option is typically used for DSL services. Some DSL service providers supply a
Enter as provided.
Enter as provided.
Check to activate
30 Version 1.0
special DSL modem. This kind of modem only supports the PPTP tunnel to access the
Internet, you should create a PPTP tunnel that carries a PPP session and terminates on
the DSL model. Once the tunnel has been established, this kind of DSL modem will
forward the PPP session to the ISP. As long as the PPP session is connected, all the local
users will be able to share this PPP session to access to the Internet. If ISP provided you
DNS information, please select Specify DNS Server IP; otherwise, select No Default
DNS Server.
In particular, here provides 3G or 3.5G transmission rate when the device is plugged, either
a 3.5G USB Dongle or Card Bus; just check to apply for the backup. In other words, once
Dynamic IP connection is disconnected, the system automatically connects Internet via
3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G
signals until none existed. The default interval between the two connection detection is 3
minutes. The interval range is from 1 to 3 minutes.
The 3.5G feature is working as mutual backup for other 4 WAN Types, and the required
information is listed as follows, such as user name, password and SIM PIN etc. That is,
setting up the interval time to auto detect whether the Internet connection is lost or not. If
yes, the system immediately switches to 3.5G Internet connection until the original PPTP
connection is back during the next detection.
31 Version 1.0
Please enter the account’s name and password which provided by your ISP, and then
click on Next button to go on 3.3.2 LAN Setup.
3.3.1.5 HSDPA/UMTS
If you are using HSDPA/UMTS (3.5G connection) as the WAN Type, please check
HSDPA/UMTS selection on the top and fill in the required information as follows to directly
access Internet via connected 3.5G adapter. At this moment, Backup of Connection is
not available, for it is in use as the preferred—Always, Dial on demand or Manual. When
3.5G signal cannot be reached, the system starts to search downward for 3/2.75/2.5G
signals until none existed.
PPTP Server IP, My WAN IP and
My WAN Subnet Mask are all
necessary inputs.
Check to activate
32 Version 1.0
• Always: Stay connected all the time. After the Quick Setup is finished, the Internet
connection is on automatically. If disconnection is detected, the system will carry on
re-connection immediately in order to stay online.
• Dial on Demand: Connect to the Internet when it is needed. After the Quick Setup is
finished, the Internet connection is on automatically. When it is idled for the set-value
(0~60 Minutes), the connection will be disconnected automatically. On the other hand,
setting up the value as 0 or leaving it blank works the same as the above, Always.
• Manual: Connect to the Internet by setting up each time. After the Quick Setup is
finished, user has to go to Network Configuration page to manually set up the
connection and disconnection.
If ISP provided you DNS information, please select Specify DNS Server IP; otherwise,
33 Version 1.0
select No Default DNS Server.
Click on Next button to go on 3.3.2 LAN Setup.
3.3.2 LAN Setup
If you are using 3.5G plus WLAN Mobile Server Router with multiple PCs on your LAN,
you must connect the LAN via the Ethernet ports on the built-in Ethernet switch. You must
assign a unique IP address to each device residing on your LAN. The LAN IP address
identifies the router as a node on your network; that is, its IP address must be in the same
subnet as the PCs on your LAN. The default LAN IP for the Internet Security Router is
192.168.1.1.
For Gateway IP Address, the IP address 192.168.1.xxx (xxx can be any number between
1 and 254 that is not used by another device.) Please don’t change the default LAN IP
settings at this section until you have completed the rest of the configurations and confirm
that your Internet connection is working. And the DHCP Server will automatically allocate
an unused IP address from the IP address pool to the requesting computer. You must
specify the starting and ending address of the IP address pool.
Click on Next button to proceed.
3.3.3 Wireless Setup
3.5G plus WLAN Mobile Server Router is based on industry standards to provide
The setup of pre-assigned Gateway IP
Address is suggested for good to use.
Requested to be a
s complied as LAN IP
.
34 Version 1.0
compatible high-speed wireless connectivity within your home, business or public access
wireless networks. Strictly adhering to the IEEE standard, the router will allow you to
access the data you want, when and where you want it. You will be able to enjoy the
freedom that wireless networking delivers.
For selecting configuration utility in AP/Bridge wireless connection, the Channel 6 is the
default channel; all devices on the network must be set to the same channel to
communication on the network. The default TxPreamble setting is Long (if you use high
traffic networks should use the shorter preamble type). Authentication is the security
function to prevent the connection requests from unauthorized wireless clients. As the
Encryption Type, select WEP or WPA can protect your data from eavesdroppers, if you
do not need the encryption, select “None” to skip the following setting.
For selecting configuration utility in WDS wireless connection, please refer to 3.4.3
Wireless for detail setting.
After checking each above blank and choose the suitable item as your demand, click on
Next button to proceed to next setting.
Notice: If use AP/Bridge as wireless connection to router, here suggests disabling the DHCP setup in LAN
Setup, please refer to 3.3.2 LAN.
Select AP/Bridge or WDS from drop-down list.
You can use the default ESSID unless
more than one AP/Router is deployed
in the same area. And it will show
when searching the wireless signal.
35 Version 1.0
3.3.4 Time Server Setup
The section provides time alteration. The Router keeps a record of the current date and
time, which is used to calculate and report various performance data, but changing the
router’s date and time does not affect the date and time on your PCs.
Select your time zone from the Time Zone drop-down list, or you may set the time manually;
there is no real time clock inside the router, the system date and time are maintained by
external network time server. Click on Next to continue.
3.3.5 Password Setup
Here suggests changing the password for logging into the configuration manager in terms
of security reason.
For changing password, please fills the password information into above blanks, and then
click on Next button.
Notice 1: Only the password can be changed, the user name for administrator is always admin and not be changed.
Select your time zone from
the “Time Zone” drop-down
list or you may set the time
by manual.
The password
may consist of A
-
Z, a-z, 0-9,
underscores, and a single dot (.)
36 Version 1.0
Notice 2: If you forget administrator’s password, please reset 3.5G plus WLAN Mobile Server Router to default setting
by pressing the Reset button on the rear panel over 5 seconds. And the password will return to admin.
3.3.6 USB Disk Management Setup
Easy to check all the USB storage devices connected to your 3.5G plus WLAN Mobile
Server Router, view the entire data folder inside each storage device, and you can
manage the disk formatting/partitioning via click on the button of this page.
Select the USB Disk and click on OK button for refreshing all disks before you execute disk
partition, and the Unplug button will appear. To partition/format the disk, please select the
disk and click on Format button. Moreover, if you want to view the data inside the disk,
please go to 3.3.10 FTP Sever Setup to enable FTP server and then click on Disk Explorer
to view all folders inside the device.
Notice: You have to click on Unplug button before removing the USB devices from 3.5G plus WLAN Mobile
Server Router.
3.3.7 User Account Management Setup
Personal users can use each individual application such as My Status, My Webcam and
My Document. This section is to set the user’s right. Also, all the users’ rights will be
37 Version 1.0
showed in User Account List and can be edited or deleted by clicking the meaning text.
Set each user’s right and space arrangement, and then click on Add button for saving
user’s account. Click on Next button after finished.
3.3.8 Firewall Setup
The Firewall rules of 3.5G plus WLAN Mobile Server Router are an advance feature used
to deny or allow traffic from passing through the router.
Input the User’s name and password, and then
click on “Add”, and you will see the user
information appear on the “User Account List”
38 Version 1.0
The default setting for Firewall Protection Level security is Low, which attacks Blocking
Policy, allow all Inbound and Outbound IP Filter Policy, and allow all router service access
policy from WAN. Please change it as your demand, and click on Next button to next step
(see also 3.4.2.1 Firewall Configuration).
3.3.9 QoS Configuration Setup
QoS management helps to set and evaluate QoS policies and goals. It is the particular
concern for the continuous transmission of high-bandwidth video and multimedia
information. Transmitting this kind of content dependably is difficult in public networks
using ordinary best effort protocols.
Make sure your connecting bandwidth with ISP and set the priority percentage. Once setting
the QoS service, the transmitting performance will be affected, so please ensure your
connection setting before doing this setup. Click on Next button to next step after finishing
the above.
Input the figures by demand to decide your
priority order.
39 Version 1.0
3.3.10 FTP Server Setup
3.5G plus WLAN Mobile Server Router can be the FTP Server providing users to transmit
files, also for the guest to download the files from assigned website. Moreover, by
connecting USB HDD, USB Flash to the router, user can easily set up a FTP Server to
share or download files for local or remote users.
Set the FTP Server and related setting. Disable the function as demand, and click on Next
button to continue.
3.3.11 Printer Server Setup
3.5G plus WLAN Mobile Server Router supports LPR-protocol, as well as NetBIOS, and is
convenient for sharing printer. In other words, it is an Internet access solution for your
LAN/WAN, which provides you the shared web surfing, and supports USB interface printer.
Any users in the same subnet of 3.5G plus WLAN Mobile Server Router can print their
document via the network printers.
Enable the printer and click on Next button to next setup.
Notice: After above Printer Server in Quick Setup finished, the related printing settings on 3.5G plus WLAN
Mobile Server Router and PC have to be set up, too. Please refer to 3.6.5 Printer Server to set the
details.
If the USB device isn’t enabled first,
you can’t enable FTP Server. (Not
even click on “Enable”)
If the printer isn’t connected,
you can’t choose “Enable”.
40 Version 1.0
3.3.12 Web Camera Server Setup
If you plan to use 3.5G plus WLAN Mobile Server Router as a Web Camera site, connect
a supported USB Web Camera to the USB port of 3.5G plus WLAN Mobile Server Router.
Check to enable the webcam server and WAN access by demand.
Click on Next button to next step.
Notice: Before webcam server enabled, please make sure the webcam has connected to the product; otherwise,
the “Enable” selection can’t be checked.
3.3.13 Samba Server Setup
3.5G plus WLAN Mobile Server Router supports NetBIOS protocol, providing network
neighbors to share file folders or printer.
Click on Next button to next setup.
41 Version 1.0
3.3.14 Quick Setup Finish
The Quick Setup has been completed successfully when you see this screen.
To apply your new settings, please click on Finish button to reboot system automatically
and go to the product’s diagram homepage. You may connect to Internet via wired or
wireless at this moment according to above settings.
3.4 IP Configuration
This function allows you to add routing rules into 3.5G plus WLAN Mobile Server Router. It
is useful if you connect several computers behind 3.5G plus WLAN Mobile Server Router to
share the same connection to Internet.
3.4.1 WAN
Select WAN under the IP Config menu. 3.5G plus WLAN Mobile Server Router supports
four WAN connection types, i.e. Static IP Address, Dynamic IP Address, PPPoE, PPTP
and HSDPA/UMTS. Follow the instructions below for each to set up accordingly.
3.4.1.1 Static IP
The WAN (Wide Area Network) page shows the settings that are used to connect to your
ISP (Internet Service Provider). Please select the Static IP for your specific ISP.
42 Version 1.0
If you applied for a Static IP connection type from ISP, please follow the steps to set up your
WAN connection.
1. IP Address
Input your IP Address supplied by ISP. If you don’t know, please check with your ISP.
2. Subnet Mask
Input Subnet Mask, normally it is 255.255.255.0.
3. ISP Gateway Address
Input ISP Gateway Address. If you don’t know, please check with your ISP.
4. HSDPA/UMTS Backup
The default interval between the two connection detection is 3 minutes, and the range is
from 1 to 3 minutes. Once Internet connection is disconnected, the system automatically
connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search
downward for 3/2.75/2.5G signals until none existed. Please check to activate or not.
5. 3.5G
43 Version 1.0
This feature requires user to enter user name, password and SIM PIN etc.; also it is
working as mutual backup for other 4 WAN Types. That is, setting up the interval time to
auto detect whether the Internet connection is lost or not. If yes, the system immediately
switches to 3.5G Internet connection until the original connection is back during the next
detection.
6. DNS
If ISP provides you DNS information, please select Specify DNS Server IP and input
the DNS information into the blank; otherwise, select No Default DNS Server.
7. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.4.1.2 Dynamic IP
If you applied for a Dynamic IP connection type from ISP, please follow the steps to set up
your WAN connection. Cable modem providers typically use dynamic assignment of IP
Address.
44 Version 1.0
1. Host Name
The host name is optional; but if your ISP requires you to input a specific host name,
please put it in, for example, 3.5G plus WLAN Mobile Server Router applied from ISP.
Generally, Cable Modem will provide the hostname information.
2. MAC Address: Keep, Clone & Input MAC Address
Select Keep or Clone MAC Address for copying the MAC address of your Ethernet
adapter to the gateway, or input a group of MAC Address. Generally, your ISP will
inform you.
3. HSDPA/UMTS Backup
The default interval between the two connection detection is 3 minutes, and the range is
from 1 to 3 minutes. Once Internet connection is disconnected, the system automatically
connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search
downward for 3/2.75/2.5G signals until none existed. Please check to activate or not.
4. 3.5G
This feature requires user to enter user name, password and SIM PIN etc.; also it is
45 Version 1.0
working as mutual backup for other 4 WAN Types. That is, setting up the interval time to
auto detect whether the Internet connection is lost or not. If yes, the system immediately
switches to 3.5G Internet connection until the original connection is back during the next
detection.
5. DNS
If ISP provides you DNS information, please select Specify DNS Server IP and input
the DNS information into the blank; otherwise, select No Default DNS Server.
6. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.4.1.3 PPPoE
If you applied for a PPPoE connection type from ISP, please follow the steps to set up your
WAN connection.
46 Version 1.0
1. User Name
Input your user name supplied by ISP. If you don’t know, please check with your ISP.
2. Password
Input your Password supplied by ISP.
3. MTU
MTU stands for Maximum Transmission Unit. For PPPoE connection, you may need to
set the MTU setting in order to work correctly with your ISP.
4. Idle Time
It is the time of inactivity before disconnecting your PPPoE session. Enter an Idle Time
(in minutes) to define a maximum period of time for which the Internet connect is
maintained during inactivity. If the connection is inactive for longer than the defined Idle
Time, then the connection will be dropped. Either set this to zero or enable
Auto-reconnect to disable this feature.
5. Auto-reconnect
If checked, the Router will automatically connect to your ISP after your system is
restarted or if the connection is dropped.
6. HSDPA/UMTS Backup
The default interval between the two connection detection is 3 minutes, and the range is
from 1 to 3 minutes. Once Internet connection is disconnected, the system automatically
connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search
downward for 3/2.75/2.5G signals until none existed. Please check to activate or not.
7. 3.5G
This feature requires user to enter user name, password and SIM PIN etc.; also it is
working as mutual backup for other 4 WAN Types. That is, setting up the interval time to
auto detect whether the Internet connection is lost or not. If yes, the system immediately
switches to 3.5G Internet connection until the original connection is back during the next
detection.
8. DNS
If ISP provides you DNS information, please select Specify DNS Server IP and input
the DNS information into the blank; otherwise, select No Default DNS Server.
9. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.4.1.4 PPTP
If you have applied for a PPTP connection type from ISP, please follow the steps to set up
your WAN connection.
47 Version 1.0
1. PPTP
Select connect to PPTP by Dial On Demand, Always Online or Manual connects.
2. PPTP Account
Input the PPTP Account supplied by ISP, 3.5G plus WLAN Mobile Server Router, for
example. If you don’t know, please check with your ISP.
Notice: Don’t copy the mentioned example as yours.
3. PPTP Password
Input the Password supplied by ISP.
4. Retype your Password
Retype the password into this blank for confirming.
48 Version 1.0
5. PPTP Server IP
Input the Server IP supplied by ISP. If you don’t know, please check with your ISP.
Input the WAN IP address provided by your ISP.
6. My WAN Subnet Mask
Input the WAN Subnet Mask supplied by your ISP. If you don’t know, please check with
your ISP.
7. MTU
MTU stands for Maximum Transmission Unit. For PPTP connections, you may need to
set the MTU setting in order to work correctly with your ISP.
8. Maximum Idle Time
It is the time of inactivity before disconnecting your PPTP session. Enter an Idle Time
(in minutes) to define a maximum period of time for which the Internet connect is
maintained during inactivity. If the connection is inactive for longer than the defined Idle
Time, then the connection will be dropped. Either set this to zero or enable
Auto-reconnect to disable this feature.
9. HSDPA/UMTS Backup
The default interval between the two connection detection is 3 minutes, and the range is
from 1 to 3 minutes. Once Internet connection is disconnected, the system automatically
connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search
downward for 3/2.75/2.5G signals until none existed. Please check to activate or not.
10. 3.5G
This feature requires user to enter user name, password and SIM PIN etc.; also it is
working as mutual backup for other 4 WAN Types. That is, setting up the interval time to
auto detect whether the Internet connection is lost or not. If yes, the system immediately
switches to 3.5G Internet connection until the original connection is back during the next
detection.
11. DNS
If ISP provides you DNS information, please select Specify DNS Server IP and input
the DNS information into the blank; otherwise, select No Default DNS Server.
12. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.4.1.5 HSDPA/UMTS
If you have applied for a HSDPA/UMTS connection type from ISP, please follow the steps to
set up your WAN connection. At this moment, Backup of Connection is not available.
49 Version 1.0
When 3.5G signal cannot be reached, the system starts to search downward for
3/2.75/2.5G signals until none existed.
1. 3.5G
This feature requires user to enter user name, password and SIM PIN etc.; also it is
working as mutual backup for other 4 WAN Types. That is, setting up the interval time to
auto detect whether the Internet connection is lost or not. If yes, the system immediately
switches to 3.5G Internet connection until the original connection is back during the next
detection.
2. Always
Stay connected all the time. After the Setup is finished, the Internet connection is on
automatically. If disconnection is detected, the system will carry on re-connection
immediately in order to stay online.
3. Dial on Demand
Connect to the Internet when it is needed. After the Setup is finished, the Internet
connection is on automatically. When it is idled for the set-value (0~60 Minutes), the
connection will be disconnected automatically. On the other hand, setting up the value
as 0 or leaving it blank works the same as the above, Always.
4. Manual
50 Version 1.0
Connect to the Internet by setting up each time. After the Setup is finished, user has to
go to Network Configuration page to manually set up the connection and
disconnection.
5. DNS
If ISP provides you DNS information, please select Specify DNS Server IP and input
the DNS information into the blank; otherwise, select No Default DNS Server.
6. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.4.2 LAN
Use this page to set up the local IP address and subnet mask for your router. Please select
LAN under the IP Config menu and follow the instructions below to enter the LAN setting
page to configure the settings you want.
1. IP Address
The default value of LAN IP address is 192.168.1.1 for this router.
2. IP Netmask
Input Subnet Mask, normally it is 255.255.255.0.
3. DHCP
Enable or disable DHCP services. The DHCP server will automatically allocate an
unused IP address from the IP address pool to the requesting computer if enabled.
4. Start IP
This field specifies the first address in the pool to be assigned by the DHCP server in
your local network. The default setting is 2.
5. End IP
This filed specifies the last address in the pool to be assigned by the DHCP server in
your local network. The default setting is 253.
6. Advanced
Enable the advance setting and then setup the Router, DNS and WINS value.
7. Router
This field indicates the IP address of DNS to provide to clients that request IP Address
from DHCP Server, the default setting is the same with LAN IP address.
51 Version 1.0
8. DNS
This field indicates the IP address of DNS to provide to clients that request IP Address
from DHCP Server, the default setting is the same with LAN IP address.
9. WINS
The Windows Internet Naming Service manages interaction of each PC with the Internet.
If you use a WINS server, enter IP Address of server here.
10. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
Besides, the DHCP information will be listed below, like DHCP Clients list, including IP
Address and MAC address.
3.4.3 Wireless
3.5G plus WLAN Mobile Server Router enables fastest 54 Mbps IEEE802.11g wireless
transmissions and keeps compatibility with existing IEEE 802.11b devices. 3.5G plus WLAN
Mobile Server Router complies with IEEE 802.11b standard. Please select Wireless under
the main menu. Follow the instructions to configure the Wireless settings.
52 Version 1.0
1. Wireless
Select AP/Bridge or WDS to allow or disallow the wireless operation.
2. Wireless Mode
This field indicates the 802.11g interface mode. “802.11G” prevents the 802.11b clients
from accessing the router. “802.11B/G” allows both 802.11b and 802.11g clients to
access the router. “802.11B” will enable the network as an 802.11b wireless network. By
default, the mode is “802.11B/G”.
3. ESSID
You can use the default ESSID and radio channel unless more than one 3.5G plus
WLAN Mobile Server Router or access point is deployed in the same area. Under this
situation, it is advised that you should use a different ESSID and radio channel for each
of 3.5G plus WLAN Mobile Server Router or access point in order to distinguish from
each other. All of 3.5G plus WLAN Mobile Server Routers and your wireless LAN cards
must have the same ESSID to allow a wireless mobile client roaming inbetween. By
default, the ESSID is set to Wireless_Mobile_Router.
4. TxRate
53 Version 1.0
Select the transmission rate for the network. The default setting is Auto.
5. Channel
IEEE 802.11g and 802.11b devices are direct sequence spread spectrum devices that
spread a radio signal over a range of frequencies. The range of frequencies used by a
direct sequence device is called Channel.
The 802.11g and 802.11b specification supports up to 14 overlapping Channels for radio
communication. But only 11 Channels are supported in the United States and therefore
built-in on 3.5G plus WLAN Mobile Server Router. To minimize interference, configure
each of 3.5G plus WLAN Mobile Server Router to use Non-overlapping channels.
Non-overlapping channels have 25 MHz separation beginning at the first allowed
channel for the country (for the US and most of Europe, channel 1, 6 & 11 are used.)
Make sure that 3.5G plus WLAN Mobile Server Router sharing the same Channel (or
Channels close in number) is as far away from each other as possible, based on the
results of your site survey of the facility. You can find the site survey utility in 3.5G plus
WLAN Mobile Server Router’s setup CD. By default, the channel is 6.
6. Hide SSID
This term is used to increase the security level. Check it to hide SSID information
against the wireless clients that are sniffing radio. By default, this option is inactive.
7. TxPreamble
The default TxPreamble setting is Long (if you use high traffic networks should use the
shorter preamble type)
8. Beacon Interval
Beacons are packets sent by an access point to synchronize a wireless network. Specify
a beacon interval value. Default (100) is recommended.
9. RTS Threshold
This value should remain at its default setting of 2346. If you encounter inconsistent data
flow, only minor modifications to the value range between 256 and 2346 are
recommended
10. Authentication Mode
Four authentication methods are supported: Open and Shared. Select Open, your
wireless network would be intruded by anonymous. Not only your network bandwidth
would be shared; but also transmitting data might be intercepted. Select Shared
function and it can be taken effect.
11. Encrypt Type - WEP
There are two types of encrypt type can be selected, including WEP and WPA.
WEP Encryption: Enabling WEP can protect your data from eavesdroppers. If you do
not need this feature, select “None” to skip the following setting. 3.5G plus WLAN Mobile
Server Router supports both 64-bit and 128-bit encryption using the Wired Equivalent
54 Version 1.0
Privacy (WEP) algorithm. Select the type of encryption you want to use (64 or 128 bit)
and configure one to four WEP Keys. The “1280bit” method is more secure than the
“64-bit”.
Key Type: For 64bits WEP key, either 5 ASCII characters or 10 hexadecimal digitals
leading by 0x can be entered. For 128bits WEP key, either 13 ASCII characters or 26
hexadecimal digits leading by 0x can be entered.
Note: 128 bits WEP is most secure, but has more encryption/decryption overhead. Note that all wireless
devices must support the same WEP encryption bit size and have the same key. Four keys can be
entered here, but only one key can be selected at a time. The keys can be entered in ASCII or
Hexadecimal. Select the item from drop-down list you wish to use.
Pass phrase: Automatically generate four WEP keys. A WEP key is either 10 or 26
hexadecimal digits (0~9, a~f, and A~F) based on whether you select 64 bit or 128 bit in
the WEP drop-down menu. Type a combination of up to 64 letters, numbers, or symbols
in the blank, 3.5G plus WLAN Mobile Server Router uses an algorithm to generate four
WEP keys for encryption. If you want to type in the keys manually, leave this field blank.
Note: This function eases users from having to remember their passwords. But this isn’t as secure as
manual assignment.
WEP Key: At most four keys can be set. A WEP key is either 10 or 26 hexadecimal
digits (0~9, a~f, and A~F) based on whether you select 64 bit or 128 bit in the WEP
drop-down list. 3.5G plus WLAN Mobile Server Router must have at least the same
default key.
12. Encrypt Type - WPA
The WPA encrypts each frame transmitted from the radio using the pre-shared key (PSK)
which entered from this panel or a key got dynamically through 802.1x.
WPA-PSK (TKSP): Allow the access from WPA clients simultaneously and the
encryption keys are given from PSK respectively.
WPA Rekey Timer: Allows for the session keys to be refreshed over time,
minimizing the amount of data that is encrypted with the same session key.
55 Version 1.0
ASKII: The 8~63 ASCII characters can be entered, for example,
“0123456789ABCD….”
Radius with 802.x: Check this circle to enable Radius client function.
WPA Rekey Timer: Allows for the session keys to be refreshed over time,
minimizing the amount of data that is encrypted with the same session key.
RADIUS Server IP: The IP address of RADIUS server.
RADIUS Server Port: The UDP port number that the RADIUS server is listed.
The default value is 1812.
Shared Secret: The RADIUS server and client share a secret that is used to
authenticate the messages sent between them. You must configure both sides
to sue the same shared secret.
13. Apply & Cancel
Click on Apply button to save the settings. If you want to clear the settings, please click
on Cancel button. The functional button, Cancel can take effect after clicking on Apply
button.
3.4.4 DDNS
56 Version 1.0
Dynamic DNS allows you to make an assumed name as a dynamic IP address to a static
hostname. Please configure the dynamic DNS below. Please select DDNS under the IP
Config menu, and follow the instructions below to enter the DDNS setting page to configure
the settings you want.
1. Service Provider
Choose correct Service Provider from drop-down list, here including dyndns, dhs, ods
and tzo embedded in 3.5G plus WLAN Mobile Server Router.
2. Enable / Disable DDNS
Select enable to use DDNS function. Each time your IP address to WAN is changed,
and the information will be updated to DDNS service provider automatically.
3. Host Name
This field represents the host name you register to Dynamic-DNS service and expect to
export to the world.
4. User Name
User name is used as an identity to login Dynamic-DNS service.
5. Password
Password is applied to login Dynamic-DNS service.
6. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the setting on this
page.
3.5 Advanced
57 Version 1.0
There are NAT settings, Firewall setting and QoS setting included in advance setup. The
advanced setting is in Router Mode only.
3.5.1 NAT
NAT is a method of mapping one or more IP addresses and/or services ports into different
specified services, where NAT stands for Network Address Translation. It allows the internal
IP addresses of many computers on a Local Area Network (LAN) to be translated to one
public address, saving users’ cost. It also plays a security role by obscuring the true IP
addresses of important machines from potential hackers on the Internet. For convenience,
we called a router having the NAT facility as a NAT-enabled router.
3.5.1.1 Virtual Server
To offer services, like WWW, FTP, provided by a server in your local network accessible for
outside users, you should specify a local IP address to the server. Then, add the IP address
and network protocol type, port number, and name of the service in the following list. Based
on the list, the gateway will forward service request from outside users to the corresponding
local server.
58 Version 1.0
1. Enable Virtual Server: Check Enable to apply all those rules in Virtual Server List
into 3.5G plus WLAN Mobile Server Router.
2. Description: Enter the description of the virtual server, this field allows you to record
what this rule is used for.
3. Private IP: Specify the private IP address of the internal host offering the service.
4. Protocol Type: Specify the transport layer protocol (TCP or UDP).
5. Private Port: Specify the private port number of the service offered by the internal
host.
6. Public Port: Specify the private IP address of the internal host offering the service.
7. Schedule: Set up the schedule for server.
8. Add: Click on Add button to record this setting.
9. Apply & Cancel
Click on Apply button to add the settings into the list table. Click on Cancel button to
clear the settings on this page.
10. Virtual Server List
Shows all IDs and relevant information on server for administrator to edit or delete.
3.5.1.2 Virtual DMZ
59 Version 1.0
Virtual DMZ allows you to expose one computer to Internet, so that all inbound packets will
be redirected to the computer you set. It is useful while you run some applications that use
uncertain incoming ports. Please use it carefully.
1. Enable/Disable Virtual DMZ: Check Enable to apply Virtual DMZ for the Router.
2. IP Address: This field stands for the destination IP address that you like to redirect the
matched packet to.
3. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the setting on this
page.
3.5.2 Firewall
The Firewall function helps to protect your local network against attacks from outside. It also
provides a way of restricting users on the local network from accessing the Internet.
Additionally, it can filter out specific packets to trigger the router to place an outgoing
connection.
3.5.2.1 Firewall Configuration
3.5G plus WLAN Mobile Server Router provides built-in firewall functions, enabling you to
protect the system against denial of service (DoS) attacks and other types of malicious
accesses to your LAN while providing Internet access sharing at the same time. You can
also specify how to monitor attempted attacks, and who should be automatically notified.
60 Version 1.0
1. Firewall Protection Level: Select the level from the drop-down list, including High,
Medium and Low. The below screen including SPI service and ICMP setting will
change according to your level setup.
2. Enable SPI Service: 3.5G plus WLAN Mobile Server Router often monitor a wider
range of activity, such as patterns of traffic and the type of application sending traffic.
With SPI, the router looks at individual packets for patterns similar to known hacker
techniques, such as Denial of Service (DoS) attacks, Ping of Death (illegal ping
packet sizes or excessive ICMP messages), SYN Flood, LAND Attack, and IP
Spoofing. Enable it if you need.
61 Version 1.0
3. Blocking ICMP Ping from WAN side: The purpose of ICMP is to provide feedback
regarding the network and datagram, it is not to make IP a reliable transport
mechanism. ICMP messages use a basic IP datagram header with the IP data being
the ICMP message. The IP source address is that of the host or gateway sending the
ICMP message with the destination IP address being that of the original source IP
address. You can enable ICMP Ping from WAN side or not.
4. DoS Attacks Blocking Settings
Enable DoS Attacks Blocking: The following sections will explain in more detail
about DoS Defense setup by using the web configuration. There are a total 8 kinds of
defense function for the DoS Defense Setup. By default, the DoS Defense
functionality is disabled. Further, once the DoS Defense functionality is enabled, the
default values for the threshold and timeout values existing in some functions are set
to 300 packets per second and 10 seconds, respectively. A brief description for each
item in the DoS defense function is shown below.
SYN Flooding: Check or uncheck this option to enable or disable protection against
SYN Flood attacks. This attack involves sending connection requests to a server, but
never fully completing the connections. This will cause some computers to get into a
“suck state” where they cannot accept connections from legitimate users. (“SYN” is
short for SYNchronize”; this is the first step in opening an Internet connection). You
can select this box if you wish to protect the network from TCP SYN flooding.
WinNuke: Check or un-check this option to enable or disable protection against
WinNuke attacks. Some older versions of the Microsoft Windows OS are vulnerable to
this attack. If the computers in the LAN are not updated with recent versions/patches,
you are advised to enable this protection by checking this check box.
MIME Flood: Check or un-check this option to enable or disable protection against
MIME attacks. You can select this box to protect the mail server in your network
against MIME flooding.
FTP Bounce: Check or un-check this option to enable or disable protection against
FTP bounce attack. In its simplest terms, the attack is based on the misuse of the
PORT command in the FTP protocol. An attacker can establish a connection between
the FTP server machine and an arbitrary port on another system. This connection may
be used to bypass access controls that would otherwise apply.
IP Unaligned Time-Stamp: Check or un-check this option to enable or disable
protection against unaligned IP time stamp attack. Certain operating systems will
crash if they receive a frame with the IP timestamp option that isn’t aligned on a 32-bit
boundary.
Sequence Number Prediction Check: For TCP packets, sequence number is used
to guard against accidental receipt of unintended data and malicious use by the
62 Version 1.0
attackers if the ISN (Initial Sequence Number) is generated randomly. Forged packets
with valid sequence numbers can be used to gain trust from the receiving host.
Attackers can then gain access to the compromised system. Note that this attack
affects only the TCP packets originated or terminated at the Internet Security Router.
Sequence Number Out of Range Check: Protect against TCP out of range
sequence number attacks. An attacker can send a TCP packet to cause an intrusion
detection system (IDS) to become unsynchronized with the data in a connection.
Subsequent frames sent in that connection may then be ignored by the IDS. This may
indicate an unsuccessful attempt to hijack a TCP session.
ICMP Verbose: Check or un-check this option to enable or disable protection against
ICMP error message attacks. ICMP messages can be used to fold your network with
undesired traffic.
Max IP Fragment Count: Enter the maximum number of fragments the Firewall
should allow for every IP packet. This option is required if your connection to the ISP is
through PPPoE. This data is used during transmission or reception of IP fragments.
When large sized packets are sent via 3.5G plus WLAN Mobile Server Router, the
packets are chopped into fragments as large as MTU (Maximum Transmission Unit).
By default, this number is set to 45. If MTU of the interface is 1500(default for
Ethernet), then there can be a maximum of 45 fragments per IP packet. If the MTU is
less, then there can be more number of fragments and this number should be
increased.
Minimum IP Fragment Size: Enter the Minimum size of IP fragments to be allowed
through Firewall. This limit will not be enforced on the last fragment of the packet. If
the Internet traffic is such that it generates many small sized fragments, this value can
be decreased. This can be found if there are lots of packet losses, degradation in
speed and if the flowing log message is generated very often: “fragment of size less
than configured minimum fragment size detected”.
5. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
6. DoS Attacks Blocking List
The list shows all the DoS attacks blocking items.
63 Version 1.0
3.5.2.2 IP Filter
Use IP Filter to deny LAN IP addresses from accessing the Internet. You can deny specific
port numbers or all ports for the specific IP address.
1. Enable IP Filter: Check enable or disable to apply IP Filter function.
2. Enable Log: All packets between WAN and LAN will be logged.
64 Version 1.0
3. Source: To specify the appropriate IP address / mask and enter the source port
number.
4. Destination: Allows you to set the destination address / mask to which this rule
should apply and enter the source port number.
5. In/Out: Select inbound or outbound ACL (Access Control List) rules, you can control
(allow or deny) incoming or external network access to computers on your LAN.
6. Protocol: This option allows you to select protocol type. Available settings are TCP,
UDP and ICMP.
7. Listen: To check if a computer is on the Internet. It sends ping packets and listens for
replies from the specific host.
8. Time Ranges: Apply IP filter by setting time ranges.
9. Action: Select Deny, the IP filter will deny for above time range, otherwise, to allow IP
filter in above time.
10. Side: Set the IP filter from LAN or WAN, or you may select both side.
11. Add, Apply & Cancel:
After finish the above, click Add button to create the new ACL rule and add the
settings into the list table. Click on Apply button to save and Cancel button to clear
the settings on this page.
12. IP Filter List
Shows all filtered IP information for administrator to edit or delete.
3.5.2.3 MAC Filter
Use MAC filters to deny LAN computers by their MAC addresses from accessing the
Internet. You can manually add a MAC address that is currently connected to 3.5G plus
WLAN Mobile Server Router.
65 Version 1.0
1. MAC Filter Action: To deny or allow all MAC filter action.
2. Enable MAC Filter: Check enable or disable to apply MAC Filter function.
3. Enable Log: All packets between WAN and LAN will be logged.
4. Description: Enter the filter description into this blank.
5. MAC Address: Enter the MAC address manually that you want to filter.
6. Time Ranges: Apply MAC filter by setting time ranges.
7. Add, Apply & Cancel
After finish the above, click Add button to create the MAC configuration rule and add
the settings into the list table. Click on Apply button to save and Cancel button to
clear the settings on this page.
8. MAC filter list
Shows all filtered MAC information for administrator to edit or delete.
3.5.2.4 URL Filter
Keyword based URL (Uniform Resource Locator) filtering allows you to define one or
more keywords that should not appear in URL’s. Any URL containing one or more of these
keywords will be blocked. This is a policy independent feature i.e. it cannot be associated
to ACL rules. This feature can be independently enabled / disabled, but works only if
firewall is enabled.
66 Version 1.0
1. Enable URL Filter: Check enable or disable to apply URL filter function.
2. Enable log: All packets between WAN and LAN will be logged.
3. Description: Enter the filter description into this blank.
4. URL keyword: Enter the URL words into this blank to apply filter blocking, example:
“www.yahoo”, then it’ll block all the websites from www.yahoo range.
5. Time Ranges: Apply URL filter by setting time ranges.
6. Add, Apply & Cancel
After finish the above, click Add button to create the URL rule and add the settings into
the list table. Click on Apply button to save and Cancel button to clear the settings on
this page.
7. URL Filter List
Shows all filtered URL information for administrator to edit or delete.
67 Version 1.0
3.5.3 QoS
Quality of Service (QoS) refers to the capability of a network to provide better service to
selected network traffic over various technologies, including Frame Relay, Asynchronous
Transfer Mode (ATM), Ethernet and 802.1x networks, and IP-routed networks that may
use any or all of these underlying technologies. The primary goal of QoS is to provide
priority including dedicated bandwidth, controlled jitter and latency (required by some
real-time and interactive traffic), and improved loss characteristics. Also important is
making sure that providing priority for one or more flows does not make other flows fail.
QoS technologies provide the elemental building blocks that will be used for future
business applications in campus, WAN and service provider networks. This chapter
provides each setting of QoS.
68 Version 1.0
1. Enable QoS Service: One checkbox appears to activate the QoS control function or
not. Click it to force the router to perform QoS control over traffic flows. By default, it’s
enabled.
2. Current Upstream Bandwidth: Allows you to set the upper bound of the port
forwarding rate. It will be of great value to minimize the impact on other users from one
user who would otherwise monopolize the network transmission bandwidth (e.g.
playing games or downloading large files).
3. Priority: To limit the bandwidth consumed over a backbone link by FTP transfers or
give priority to an important database access. And the following applications can be
selected individually and distribute the priority level.
4. Application: Including FTP, HTTP, E-mail, Telnet, Voice, Games, IM and Video
priority setting.
5. Apply & Cancel
Click on Apply button to save the setting or Cancel button to clear the settings on this
page.
3.6 Server
3.5G plus WLAN Mobile Server Router provides FTP Server, Web Camera Server, Printer
Server and Samba Server applications.
3.6.1 Samba Server
By supporting NetBIOS Protocol, 3.5G plus WLAN Mobile Server Router provides LAN
users to share files or printer via My Network Places. Click Samba Server to proceed.
69 Version 1.0
1. Enable Samba Server
Check to Enable/Disable while connecting.
2. Workgroup Name
Fill in the name, and the default is WORKGROUP.
3. Server Name
Name your server.
4. Server Description
Describe your server by demand, and the default is Wireless Mobile Router.
5. Printer Model
Printer model appears when connected.
6. Apply & Cancel
Click Apply to save or Cancel to clear settings.
3.6.1.1 How to Access File Sharing Directory
Please follow the steps below.
【Step 1】
Go to Start and click My Computer.
70 Version 1.0
【Step 2】
Fill in blank address field with \\192.168.1.1.
【Step 3】
A window pops up asking for user name and password. If log in as an administrator,
please enter admin for both fields; otherwise, fill in with personal account and password.
Click OK after finished.
【Step 4】
As the window below appears, login user has entered file sharing directory, and the
folders underneath are all available for sharing locally.
71 Version 1.0
Note: Only 2 icons show up at most.
1. If a USB flash drive/hard disk is connected and enabled, the samba folder shows up.
2. If a USB printer is connected and enabled, the printer icon shows up.
3.6.2 FTP Server
By directly connecting USB storage devices to any USB port, FTP server can be created
with simple configuration. FTP Server utility allows both local and remote users to upload
or download files, pictures or music files from the same storage device in most easy and
timely fashion. It is also cost effective where users do not need to purchase a dedicated
PC to set up a 24-hour FTP service.
Before configuring FTP Server, please make sure the storage device is properly plugged
into any USB port on the router and make sure this USB storage device is detected by the
router.
72 Version 1.0
1. Enable FTP Server: Enabling selection for FTP Server only can be checked when
USB storage device is plugged.
2. Enable Anonymous to Login: Allow anonymous to log in after check on enable.
3. Enable FTP Access from WAN: Allow FTP access from WAN side by checking on
enable for this item.
4. FTP Server Port: Define the FTP command transfer service port. If you want to
change this port number, also remember to change the service port setting of your
FTP client.
5. Idle connection Time-Out: When a specific time value is added, FTP Server will be
de-activated if it has no activity within the time limit.
6. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
7. User Account List
A list shows all user names, staus and directory/file opened.
Notice: FTP server is compatible with FAT32 or EXT3 format USB storage device. In case you need to format
your USB storage device, please always make sure the device is formatted with FAT32 or EXT3
standard.
3.6.3 Web Camera Server
3.5G plus WLAN Mobile Server Router has built-in Web Cam Server. By connecting web
camera to the router, it allows user to monitor their home or office from remote locations.
Motion Detection function has also been built-in and allows user to use webcam to detect
any movements in their houses or offices and send email alert with captured images.
While USB storage device is
plugged, FTP Server can be
checked as enabled.
73 Version 1.0
3.6.3.1 Web Camera Server Basic Setup
1. Enable Webcam Server: Allow using this function by checking on enable.
2. Access from WAN: Allow webcam can access from WAN side by checking on enable
for this item.
3. Image format: The default is 320x240 pixels.
4. Preview: Click on this button, you can preview the image from webcam.
5. Record Setting: Please see the detail advance setting in 3.6.3.2 Web Camera
Server Advanced Configuration.
6. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.6.3.2 Web Camera Server Advanced Configuration
Click on Record Setting button, and the screen will appear as below.
1. Enable save image: If you want to save the image from webcam, please check on
enable.
2. Save image interval: For saving image, you can set the save interval time, the default
value is 5 seconds.
3. Save Location: Set the save location for webcam image, you may save into USB
74 Version 1.0
HDD or remote FTP; if select save to remote FTP, please continue follow-up remote
FTP setting.
4. USB HDD Directory: The section provides option of which folder should be used for
saving webcam image.
5. Remote FTP URL: Input the FTP URL for saving webcam image.
6. Remote FTP port: Input the FTP port number under URL to save image.
7. Remote FTP user: Enter the user’s name you like and it will be used to save the
webcam image into the FTP server.
8. Remote FTP password: Put in a password for validation while accessing.
9. Remote FTP Directory: To provide option of which folder should be used for saving
webcam image.
10. Back: Click on Back button for returning to Webcam Basic Setup screen.
11. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
3.6.3.3 Application for Web Camera
3.6.3.3.1 Web Camera Monitoring Application
Monitor your home or take pictures with a Webcam via 3.5G plus WLAN Mobile Server
75 Version 1.0
Router; one can set up the monitoring or recording of all images into the USB HDD for
reviewing. Often marketed as surveillance tools for home or office security; network
Webcams are now being employed by early adopters for more personal matters, such as
watching kids and monitoring pets. The Webcam can be remotely accessed and
controlled via a browser. In addition, record and monitor live actions with USB webcam;
then view the image through Internet browsers or WiFi mobile phones.
3.6.3.3.1.1 Web Camera Monitoring via WAN connection
The illustration below is an example for watching the webcam image via WAN connection.
How to check your WAN IP address
To monitor the webcam image from outside, you need to know the WAN IP address.
Select Network Configuration under Log & Status on main Menu after connected, and
you will see the WAN IP Address used to connect to webcam monitor screen. Here uses
210.168.117.96 as an example.
Monitor the webcam image via WAN
76 Version 1.0
Input the WAN IP Address (as you see on above screen) into browser blanks. You will see
the personal account login screen appear, and then input your own user account and
password. After logging in as a user, your will see the personal control panel screen as
below, please click on My Webcam.
There will pop-up screen shows the image from web camera as example below.
3.6.3.3.1.2 Web Camera Monitoring via WiFi Mobile Phone
You may view the monitor live action through WiFi mobile phones.
77 Version 1.0
Please fill the WAN IP address plus “/webcam.html” (e.g.
http://210.64.134.25/webcam.html)
into the mobile phone’s browser blank and you will see the webcam user login screen
appear as below.
After logging in with your own account, you will see the monitor image from web camera via
WiFi mobile phone.
3.6.3.3.2 Web Camera Recording
3.6.3.3.2.1 Administrator Setup
78 Version 1.0
3.5G plus WLAN Mobile Server Router also can record the pictures from Webcam; only
Administrator can activate the settings. Select Web Camera Server from main Menu and
enable this function, click on Record Setting button for further setting.
To set up the Webcam Advanced Configuration for each text field, the image from webcam
will be recorded into your USB HDD or Remote FTP. Click on Apply after setup finished.
For administrator, you may view all the images from webcam recording, please select
Folder Management and click on Disk Explorer to view entire folder inside the disk
including webcam record files.
79 Version 1.0
After click on Disk Explorer, you will see the folder screen appear including all the folders
inside 3.5G plus WLAN Mobile Server Router. (Below is the example.)
For getting the images from web camera or any files inside router, you may copy the files
into your own HDDs directly. In addition, all image files are stored in
webcam_recorded_files folder, click to examine the content inside.
3.6.3.3.2.2 Personal Application
All the users under administrator’s setting can view entire webcam recording images from
My Document. Please log in with your own personal account. For viewing your own folder,
please click on “My Document”.
80 Version 1.0
After click on My Document, you will see folder screen appear as the example below.
Notice: If you can’t open the folder, please check with administrator to set up your FTP access right.
3.6.4 Printer Server
81 Version 1.0
3.5G plus WLAN Mobile Server Router has two USB ports for connecting with printers to
be shared on the local area network. Follow the steps to set up your PC to connect to a
printer server.
1. Enable Printer Server: Check enable for applying printer server.
2. Enable Printer Access From WAN: Allow printer can access from WAN side by
checking on enable for this item.
3. Printer Model: The printer model will be shown when the USB printer is plugged.
4. Printer Name: Enter the name you like.
5. Printer Description: Enter your description by demand.
6. Apply & Cancel
Click on Apply button to continue. Click on Cancel button to clear the settings on this
page.
Besides the above is finished, the printer setting on PC also needs to be set as follows.
3.6.4.1 Printer Setting on PC
After enabling Printer Server in Quick Setup and Printer Server Configuration, please
follow the steps to set the detail LPR settings on your PC. (The example below is for
Windows XP platform.)
82 Version 1.0
【【【【Step 1】】】】
After setting USB printer on 3.5G plus WLAN Mobile Server Router’s setup page, please
go to
Start > Printers and Faxes to add a printer.
【【【【Step 2】】】】
Click on Add a printer item.
【【【【Step 3】】】】
Click on Next button.
83 Version 1.0
【【【【Step 4】】】】
Select Local printer attached to this computer, and click Next.
【【【【Step 5】】】】
Select Create a new port and choose Standard TCP/IP Port from drop-down list, then
click Next.
84 Version 1.0
【Step 6】
Click Next.
【Step 7】
Put in 3.5G plus WLAN Mobile Server Router’s address: 192.168.1.1 and click Next.
85 Version 1.0
【Step 8】
Select Custom and click on Settings… button to set the detail setting.
【Step 9】
Select LPR and give it the same Queue Name as USB Printer Name has shown, and
mark LPR Byte Counting Enabled. Finally, click on Next button.
86 Version 1.0
【Step 10】
Click Finish on the next screen after the aforesaid settings, you have to install the printer
driver as well.
【Step 11】
Select the Manufacturer and Printers. If your printer is not listed in the table, please
It has to be the same with the Printer Name
as shown in section 3.6.4 Printer Server
Configuration.
87 Version 1.0
insert its driver CD and then click on Have Disk… button for installation. Or click on Next
button to finish the setting.
You can name your printer, set it as default printer and share your printer as the next
screen shown, the Printer Server setting is getting completed.
【Step 12】
It shows you the printer settings that you have specified, and then click Finish.
88 Version 1.0
3.7 System Management
3.5G plus WLAN Mobile Server Router provides system management including password
changing, firmware upgrade, time setting, user’s account setting and other detail settings.
Following is detail explanation for each.
3.7.1 Reboot
If you had entered the wrong configuration while setting up your router or other utilities,
you can always reboot your 3.5G plus WLAN Mobile Server Router by this setting.
It’s necessary to reboot the router if it begins working improperly, please click on Reboot
button to reboot the router.
3.7.2 Change Password
At this section, the administrator can change the system password. Only the password
can be changed, the user name for administrator is admin and can’t be changed.
89 Version 1.0
1. Old Password: Enter the original password you set.
2. New Password: Enter the new password you want to change.
3. New Password (Confirm): Enter the new password again for confirming.
4. Apply & Cancel
Click Apply to continue or Cancel to clear the settings on this page.
3.7.3 Firmware Upgrade
There is certain risk while upgrading firmware. Upgrading firmware is not recommended
unless the significant faulty is found. You can upgrade the firmware of 3.5G plus WLAN
Mobile Server Router on this page. Make sure the firmware you want to use is on the local
hard drive of the computer. Click Firmware Upgrade to proceed.
90 Version 1.0
1. Update Firmware: Click on Browse… button to search your local hard drive and
locate the firmware to be used for update.
2. OK & Cancel
Click OK to confirm or click Cancel to clear the setting on this page.
Notice: Before using a whole new disk, please format it on your PC first, so that it can be formatted on 3.5G
plus WLAN Mobile Server Router.
3.7.4 Profile Sasve
To back up the current configuration setting or load the backup data, also you can restore
3.5G plus WLAN Mobile Server Router to default setting by this function.
91 Version 1.0
1. Save Settings To PC: Click on Save button for saving the configuration setting into
assigned location.
2. Load Settings From PC: Click on “Browse…” button for searching the saving
configuration from hard drive, and then click on Load button to load all the settings
into the router.
3. Restore To Factory Default Settings: After you have tried other methods for
troubleshooting your network, you may choose to restore 3.5G plus WLAN Mobile
Server Router to the factory default settings.
4. Apply
Click on Apply button to save the settings.
3.7.5 Remote Management
Remote Management allows 3.5G plus WLAN Mobile Server Router to be configured from
the Internet by a web browser. In general, only a member of your network can browse the
built-in web pages to perform “Administrator” tasks. This feature enables you to perform
the tasks from the remote (Internet) host.
92 Version 1.0
1. HTTP Connection Port: The port number used to access the router.
2. Remote Management: You can allow any Internet IP address to access the router, or
set up deny rule according to IP setting.
3. IP Address: Internet IP address of the computer that has access to the router.
4. Description: Enter the description for the remote configuration.
5. Add, Apply & Cancel
Click on Add button to add the remote list, click on Apply button to activate, or click on
Cancel button to clear the settings on this page.
6. Remote Management IP List
Display, edit or delete IDs, description and IP address of allowed remote list.
93 Version 1.0
3.7.6 Time
The System time is the time used by 3.5G plus WLAN Mobile Server Router for
scheduling services. You can manually set the time or connect to a NTP (Network Time
Protocol) server. If a NTP server is set, you will only need to set the time zone. If you
manually set the time, you may also set Daylight Saving dates and the system time will
automatically adjust on those dates.
1. Local Time: The default time within.
2. Default NTP Server: Select the NTP Server from the drop-down list.
3. Time Zone: Select your time zone location from the drop-down list.
4. Daylight saving time: If you are in daylight saving time area, please enable this item.
5. Set the Time: Select this item to set up time by manual, select the date and time from
each drop-down list.
6. Set Time: Select User Setup and click Set Time to set local PC time on router.
94 Version 1.0
7. Apply & Cancel
Click on Apply button to activate, or Cancel button to clear the settings.
3.7.7 UPnP Setting
UPnP (Univsersal Plug and Play) allows users to connect their UPnP-enabled broadband
router, printer server and other devices right to the network with zero-configuration,
meaning easier setup for installing the device on the network. The automatic discovery
feature enables the device to obtain an IP address, present and describe itself to other
devices and PCs on the network without having to install drivers, but to configure and use
those devices.
1. Enable/Disable UPnP: Select to enable or disable this service.
2. Apply, Cancel
Click on Apply button to activate this function or Cancel button to clear the setting.
3.7.8 User Account Management
Personal users can use each individual application such as My Status, My Webcam and
My Document. This section is to set the user’s right. Also, all the users’ rights will be
showed in User Account List and allowed to edit or delete by clicking the linking text.
95 Version 1.0
1. Max Login User: Set up the maximum users to log in at the same time, select the
number from drop-down list. If you want to change the maximum login users only
without changing user’s information, please click on OK button after select login user’s
number.
2. User Name: Create the user name in this blank.
3. Password: Set up the user’s password.
96 Version 1.0
4. User Right: Check to allow set-user accessing Samba folder, monitoring from
webcam or using FTP server.
5. Activated: Click On to allow the user’s right to be applied immediately.
6. Add, Apply & Cancel
After finishing the above, click Add button to create user account. Click on Apply button
to add set-user into the account list or Cancel button to clear the settings on this page.
7. User Account List
The list shows all users’ names, passwords, status and rights.
3.7.9 Folder Management
Easy to check all the USB storage devices connected to 3.5G plus WLAN Mobile Server
Router, view the entire data folder inside each storage devices, and you can manage the
disk formatting / partition via clicking the button on this page.
1. Select the USB Disk and click OK for refreshing all disks before you perform disk
partition, and the Unplug button appears afterwards.
2. To partition/format the disk, please select the disk and click on Format button.
3. Moreover, if you want to view the data inside the disk, please go to 3.3.10 FTP Sever
Setup to enable FTP server and then click on Disk Explorer to view all the folders
inside the device.
97 Version 1.0
Notice: You have to click on Unplug button before removing the USB device from 3.5G plus WLAN Mobile
Server Router.
3.7.10 Email Alert
To monitor router activity, you can run on a local PC or a remote one elsewhere on the
Internet. And 3.5G plus WLAN Mobile Server Router provides the email alert facility so that
the log messages can be packed as an e-mail for someone who wants to receive these
messages by scheduled time. In the following, here explains how to set up the email alert
function.
98 Version 1.0
1. Email Alert: Check the enable box to activate the email alert service.
2. SMTP Server: Specify an IP address of the SMTP server which can send mails from
your 3.5G plus WLAN Mobile Server Router to the recipients’ mailboxes directly.
3. Your Mail (from): Enter the email address indicated the sending location.
4. SMTP Auth: If the email alert needs to be sent via SMTP authentication, please check
this item, and then enter the required account and password.
5. Account: Enter the email account from which you want to send the alert.
6. Password: Enter the email account password to validate.
7. Email Address (To): Enter the email address where to receive the alert.
8. Schedule: Arrange to send the alert when event happens or by regular time.
9. Add, Apply & Cancel
After finishing the above, click Add to set up the rule into email alert list. Then, click
Apply to save or Cancel to clear the settings on this page.
10. Email Alert List
Display, edit or delete a list of relative information in regarding to the above mentioned.
99 Version 1.0
11. Refresh & Delete
Click on Refresh to renew the login data and other system status information, or click
on Delete to clear these logs.
3.8 Log & Status
3.5G plus WLAN Mobile Server Router provides the log list, connection status and user’s
account.
3.8.1 Network Configuration
Network Configuration shows all connection status of LAN, WAN, Wireless and plugged
USB devices.
Each block shows configuration status, you may click Refresh to update the screen list. If
WAN connection is in dynamic, click Release to free the used IP or Renew to get a new
one.
100 Version 1.0
3.8.2 User Account List
This section shows all users’ information.
Check the user name, status and opened directory/file on screen.
Loading...