Soltek SL-KT400-C User Manual

KT400-C

Contents

Chapter 1 Specification ............................................. 8

1-1 KT400-C Mainboard Layout**..............................................9

1-2 Mainboard Specifications .................................................... 10

1-2.1 CPU Socket ...................................................................................10

1-2.2 System Chipsets ........................................................................... 10

1-2.3 Memory ......................................................................................... 10

1-2.4 BIOS............................................................................................... 10

1-2.5 Accelerated Graphics Port (AGP) Interface........................... 10

1-2.6 Advanced System Power Management .................................... 11

1-2.7 Multi-I/O Functions .................................................................... 11

1-2.8 Expansion Slots ............................................................................ 11

1-2.9 AC’97 Audio Codec on board.................................................... 12

1-2.10 Hardware Monitor on board ................................................... 12

1-2.11 Form Factor................................................................................ 12

1-3 Mainboard Specification Table ........................................... 13

1-4 Chipset System Block Diagram........................................... 14

Chapter 2 Hardware Setup..................................... 16

2-1 CPU Identification and Installation ................................... 17

2-1.1 CPU Identification Legends....................................................... 17

2-1.2 CPU Installation with Socket 462 ............................................. 18

2-2 Memory Installation ............................................................. 19

2-2.1 To Install DDR SDRAM Module .............................................. 19

2-2.2 To Remove a DIMM .................................................................... 20

2-3 AGP Slot Installation ............................................................ 21

2-4 IDE Connector Installation ................................................. 22

2-5 Floppy Drive Connector ( FDC ) Installation................... 23

2-6 ATX Power Supply Installation .......................................... 24

4

Contents

2-7 Jumper / Switch Settings ...................................................... 25

2-7.1 How to tackle the Jumpers: ....................................................... 26

2-7.2 SW1: CPU Clock/Overclock Select ..........................................26

2-7.3 JBAT1: Clear CMOS ..................................................................27

2-7.4 Jp1: Anti-burn Shield (ABSII).................................................. 28

2-7.5 JP2: KB/Mouse Power On / Wake Up ..................................... 29

2-8 Other Connectors Configuration........................................ 30

2-8.1 On-board FAN Connectors ........................................................ 30

2-8.2 USB Ports and USB Pin-headers ..............................................31

2-8.3 Chassis Panel Connectors .......................................................... 32

2-8.4 PS/2 Mouse and PS/2 Keyboard ............................................... 32

2-8.5 CD-ROM Audio Connectors (CD-In1) ....................................33

2-8.6 Thermal Connectors.................................................................... 34

2-8.7 Complex Pin-header (Front Panel Connectors)..................... 35

2-8.8 JAUD1: Front Panel Audio Connector (optional) .................37

Chapter 3 Software Setup ....................................... 38

3-1 Open Up Support CD: .......................................................... 39

3-2 Proceed to VIA 4-IN-1 Drivers Installation ...................... 40

3-3 Proceed to AC’97 Audio Driver Installation..................... 42

3-4 Install USB 2.0 Driver for Win98 / Me / 2000 / XP.......... 43

3-5 To Install Hardware Monitor Utility.................................. 45

3-5.1 Installation ................................................................................... 45

3-5.2 Verification .................................................................................. 46

Chapter 4 AMI BIOS Setup.................................... 48

4-1 About BIOS Setup ................................................................. 49

4-2 To Run BIOS Setup ............................................................... 49

4-3 About CMOS .......................................................................... 49

4-4 The POST ( Power On Self Test ) ....................................... 49

5

KT400-C

4-5 To Update BIOS ..................................................................... 50

4-6 BIOS SETUP --- CMOS Setup Utility................................ 52

4-6.1 CMOS Setup Utility ....................................................................52

4-6.2 Standard CMOS Setup ...............................................................53

4-6.3 Advanced BIOS Features ...........................................................56

4-6.4 Advanced Chipset Features ....................................................... 59

4-6.5 Power Management Features .................................................... 62

4-6.6 PNP / PCI Configurations .......................................................... 65

4-6.7 Integrated Peripherals................................................................ 67

4-6.8 SmartDoc Anti-Burn Shield....................................................... 70

4-6.9 Frequency/Voltage Control....................................................... 72

4-6.10 System Information................................................................... 74

4-6.11 Set Supervisor Password ..........................................................75

4-6.12 Load Optimized Defaults ........................................................77

4-6.13 Save & Exit Setup...................................................................... 77

4-6.14 Exit Without Saving .................................................................. 77

APPENDICES.......................................................... 78

Appendix-1 Identify Mainboard Model Number ................... 79

Appendix-2 Technical Terms...................................................... 80

6

Contents

ITEM CHECKUP

• Mainboard

• Mainboard User Manual

• Multi-lingual Quick Installation Guide

• Support CD

• Bundled Bonus Pack CD

• Bundled Bonus Pack Manual

• Cables :
ATA66/100/133 IDE Cable
FDD Cable
USB Cable (Optional)

7

KT400-C

Chapter 1 Specification

Introduction

This mainboard features an integration of the powerful AMD proces­sors Athlon/Athlon XP/Duron and the North Bridge VIA Apollo KT400
plus South Bridge VT8235, with which the whole system performance
supports 333/266/200 MHz system bus.

VIA Apollo KT400 plus VT8235 supports on-board AMD processors
to implement the 333/266/200MHz Front Side Bus, the AGP 8X/4X
interface, the LPC Super I/O, the DDR *400/333 MHz SDRAM, the 2­channel AC’97 Audio interface, the USB 2.0 interface and ATA 133/100/
66 data transfer rate. This chapter is to introduce to users every ad­vanced function of this high performance integration.

Topics included in this chapter are:
1-1 Mainboard Layout
1-2 Mainboard Specifications**
1-3 Mainboard Specification Table
1-4 Chipset System Block Diagram

** If any difference is found between this manual and the Main­board you are using, please look up the ERRATA/UPDATE Slip
enclosed inside for the correction or updated information, or
else contact the Mainboard Dealer or visit our Web Site for the
latest manual update.

8

Chapter 1 Specification

1-1 KT400-C Mainboard Layout**

JP1

1

JBAT1

1

CN8

Fan2

HDD/LED

--

++

Speaker

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

RST

IR

+

PLED

Socket 462

RT1

KT400

AGP 8X/4X

ON

SW1

1 2 3 4 5

PWR

USB2

-

1

VIA

DIP

9

1

USB3

Generator

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM1

Clock

VIA

VT8235

IDE1

1

IDE2

1

FDC1

1

9

DIMM2

Fan3

Mouse

(on top)

PS/2 K/B



USB0

(on top)

USB1

(underside)

COM1

COM2

Line

Out

Line

In

MIC



ALC202A

AC'97

Codec

(underside)

JP2

1

LPT1

Game/MIDI Port

CD-In1

1

RT2





LPC I/O

IT8705

BIOS

Li

Battery

1

JAUD1

Fan1



9

9

KT400-C

1-2 Mainboard Specifications

1-2.1 CPU Socket

CPU Socket 462 (Socket A) on board, supporting AMD Athlon, Athlon
XP and Duron processors and implementing 333/266/200MHz system
bus

1-2.2 System Chipsets

• North Bridge VIA KT400 for managing and supporting 333/266/

200MHz system Bus, AGP 8X/4X interface and DDR 333/266MHz
Memory Interface *with an enhanced support of DDR 400MHz
Memory Module which should have passed Soltek DDR 400 Memory
Module Validation.

• South Bridge VIA VT8235 working with North Bridge KT400 supporting

the V-Link, LPC Super I/O, PCI interface, ATA133 interface, USB V2.
0 interface, as well as AC’97 Audio 2-channel interface.

1-2.3 Memory

2 DDR DIMM 184-pin slots on board :

• Supporting unregistered, non-ECC *DDR 400/333/266/200 SDRAM

up to 2 GBs (DDR 400 Module supported conditionally)

• Supporting installation of mixed volumes yet same type of DDR

SDRAM modules

* Soltek Computer Inc. typically runs a DDR 400 Memory Module

Validation Program for Chipset VIA KT400/P4X400A. Detailed
information is available in Soltek Web Site: www.soltek.com.tw

1-2.4 BIOS

• Supporting Plug & Play V1.0

• Flash Memory for easy upgrade

• Supporting BIOS Writing Protection and Year 2000 compliant

• Supporting BIOS Setup (See Chapter 4 BIOS Setup)

1-2.5 Accelerated Graphics Port (AGP) Interface

AGP Controller embedded on board, supporting:

• 1.5V(8X/4X) power mode only, 1 AGP Slot supported

• 8X 66MHz AD and SBA signaling; AGP pipelined split-transaction

longburst transfers up to 2GB/sec.

• AGP 8X/4X supported, AGP V3.0 compliant

10

Chapter 1 Specification

1-2.6 Advanced System Power Management

Advanced Configuration and Power Interface incorporated in BIOS for
reducing power consumption :

• ACPI 1.0 compliant (Advanced Configuration and Power Interface)

• APM V1.2 compliant (Legacy Power Management)

• ACPI Suspend function supported

• PS/2 Keyboard & Mouse Power On

• Real Time Clock (RTC) with date alarm, month alarm, and century

field

1-2.7 Multi-I/O Functions

• PCI EIDE Controller, supporting:

-- 2 ATA 133 / 100 / 66 IDE connectors supporting up to 4 IDE devices

• Dedicated IR Functions:

-- 1x5 IR connector dedicated to IR function with Infrared-IrDA (HPSIR)
and ASK (Amplitude Shift Keyed) IR

• Multi-mode parallel data transfer:

-- Standard mode, high speed mode ECP and enhanced mode EPP

• Floppy Drive Connector:

-- 1 FDD connector supporting 2 floppy drives with drive swap support

• Universal Serial Bus Transfer Mode:

-- USB V2.0 compliant, 480 Mb/s USB Bus, supporting Win 98 and later
operating systems; USB drivers provided in Support CD for installation

-- 2 built-in USB connectors and 2 more USB pin-headers which require 2
optional USB cables to provide 4 more USB ports

• PS/2 Keyboard and PS/2 Mouse

• UARTs (Universal Asynchronous Receiver / Transmitter):

-- 2 complete serial ports (COM1 & COM2) on board

1-2.8 Expansion Slots

• 5 PCI Bus Master slots

• 1 AGP 8X/4X slot

• 2 DDR DIMM slots

11

KT400-C

1-2.9 AC’97 Audio Codec on board

AC’97 Audio Codec on board, 2-channel interface compliant

1-2.10 Hardware Monitor on board

• Hardware Monitor integrated in LPC I/O IT8705F, providing monitor­ing functions on hardware voltage, temperatures and fan speeds.

• Utility Software SmartGuardian for displaying monitor status is en­closed in Support CD for user’s installation.

1-2.11 Form Factor

• ATX form factor, ATX power supply

• Mainboard size: 305mm x 190mm

12

Chapter 1 Specification

1-3 Mainboard Specification Table

KT400-C Specifications and Features

CPU

North Bridge

South Bridge

BIOS

Memory

I/O Chip

AGP interface

Audio

IDE Interface

VGA

PCI Slots

I/O Connectors

Other common
features

Socket 462 for AMD Athlon, Athlon XP, Duron CPU

VIA KT400, supporting 333/266/200 MHz FSB

VT8235

AMI BIOS

Supporting DDR *400/333/266 SDRAM, up to 2GB
in 2 DDR SDIMM slots

ITE IT8705F with Hardware Monitor

AGP 8X/4X mode only

AC’97 Audio Codec, 2-channel compliant

2 ATA 133/100/66 IDE

Not integrated on board

5 PCI Master slots on board

6 USB V2.0, 1 FDD port, 2 COM ports, 1 LPT,
1 IrDA, 1 PS/2 K/B, 1 PS/2 Mouse

BIOS Writing Protection;
Keyboard/ Mouse Power On;
ATX Power Supply;
ATX form factor

13

KT400-C

1-4 Chipset System Block Diagram

Socket 462

for AMD CPUs

System Bus 333/266/200MHz

AGP Slot

4 IDE
Devices

Mouse

Keyboard

Serial Ports
Printer Port

Game/MIDI

H/Monitor

AGP 8X/4X

ATA 133/100/66

IR

FDD

LPC I/O
IT8705

VIA KT400
North Bridge

V-Link

VT8235
South
Bridge

DDR memory
Interface

DDR 400/
333/266
SDRAM

PCI Bus

AC’97

USB Bus V2.0

BIOS

System
Memory

5 PCI Slots

Audio Codec
(2-channel)

USB
Ports

Socket 462 + VIA KT400 + VIA VT8235 Diagram

14

KT400-C

Chapter 2 Hardware Setup

To Get Things Ready for Hardware Setup !

1. We recommend to install your CPU before any other components.

For detailed installation instructions of processor, you can also refer
to the pamphlet enclosed in your CPU package.

2. Installing a cooling fan with a good heatsink is a must for proper heat

dissipation for your CPU. Get ready an appropriate fan with heatsink
for proper installation. Improper fan and installation will damage your
CPU.

3. In case CPU Vcore, CPU clock or Frequency Ratio is adjustable on

board, please follow the instructions described in the User Manual
for proper setup. Incorrect setting will cause damage to your CPU.

The following topics are included in this chapter:

2-1 CPU Identification and Installation
2-2 Memory Installation
2-3 AGP Slot Installation
2-4 IDE Connector Installation
2-5 Floppy Drive Connector ( FDC ) Installation
2-6 ATX Power Supply Installation
2-7 Jumper Settings
2-8 Other Connectors Configuration
2-9 IRQ Description

16

Chapter 2 Hardware Setup

AMD

AMD Athlon

T
M

A
X
D
A
2
4
0
0
D
K
V
3
C

R
F
B
C
Y
A
5
2
8
0
0
6
1

X
X
X
X
X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X
X

2-1 CPU Identification and Installation

2-1.1 CPU Identification Legends

AMD

XXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXX
XXXXXXXXX
XXXXXXXXXXX
XXXX

.18 micron process CPU .13 micron process CPU

AMD Athlon(Duron)

AX 1900 D M T 3 C

(1) (2) (3) (4) (5) (6) (7)

Family / Architecture:

(1)

A, AX, AXDA=AMD Athlon Processor
D, DHD=AMD Duron Processor

Speed: 1000=1000MHz, 1600=1400MHz, 1700=1467MHz,
1800=1533Mhz, 1900=1600MHz, 2000=1667MHz, 2100=1733MHz,

(2)

2200=1800MHz, 2400=2000MHz, 2700=2167MHz

(3)

(4)

(5)

(6)

(7)

Package Type: M=Card Module, A=PGA, D=OPGA

Voltage: L=1.5V, U=1.6V, K=1.65V, P=1.7V, M=1.75V, N=1.8V

Case Temperature: Q=60˚C, X=65˚C, R=70˚C, Y=75˚C,
T=90˚C, S=95˚C

Size of L2 Cache: 1=64Kbyte, 2=128Kbyte, 3=256Kbyte

Max FSB: A=B=200MHz, C=266MHz, D=333MHz
Note: Get the Host CPU Clock by dividing FSB by 2.

17

KT400-C

2-1.2 CPU Installation with Socket 462

This mainboard is built with CPU Socket 462 supporting the AMD CPUs
Athlon, Athlon XP and Duron:

• Follow the steps described in this section to install CPU into the on­board Socket 462.

• After installation of CPU, you must also install a proper cooling fan
on top of the CPU and connect the Fan cable to the CPU fan
connector.

1. First pull sideways the lever of
Socket 462, and then turn it up

0

so as to raise the upper layer

90
of the socket from the lower
platform.

2. Configure Pin 1 of CPU to Pin 1

SOCKET 462

D

M

A

of the Socket, just as the way
shown in the diagram on the
right. Adjust the position of CPU
until you can feel all CPU pins
get into the pin holes of the
socket.

SOCKET 462

Pin 1

3. Make sure that all CPU pins have
completely entered the socket
and then lower down the lever
to lock up CPU to socket.

18

D

M

A

Pin 1

2

6

4

T

E

K

C

O

S

Chapter 2 Hardware Setup

2-2 Memory Installation

How to tackle the memory Modules:

• Make sure to unplug your power supply before adding or removing

memory module. Failure to do so may cause severe damage to both
your mainboard and the memory module.

• Pay attention to the orientation of the DIMM slots. Forcing a DIMM

into a slot improperly will damage the memory module and slot itself.

• Make sure you have the right type of memory module for your

mainboard.

2-2.1 To Install DDR SDRAM Module

• This series supports up to 2GB unbuffered *DDR 400/333/266 SDRAM,

with 2 DDR DIMM slots on board. Do not insert other type of mod­ules into these slots. Memory support is upgradable to DDR 400 with­out guarantee of success in BIOS Setup.

* DDR 400 Module is supported on condition that the module has

passed Soltek DDR 400 Memory Module Validation Test. Soltek
Computer Inc. typically runs a DDR 400 Memory Module Validation
Program for Chipset VIA KT400/P4X400A. Detailed information is
available in Soltek Web Site: www.soltek.com.tw

• DDR DIMM slot has 184-pins and one notch. Insert a DDR SDRAM

vertically into the 184-pin slot with the notch-to-rib matching.

184-Pin DIMM Notch Key Definitions

DRAM Key Position Voltage Key Position

DDR Notch

2.5V

DDR Rib

Module Latch

19

KT400-C

2-2.2 To Remove a DIMM

Press down the holding latches on both sides of slot to release the
module from the DIMM slot.

DDR DIMM Slots
(184-pin)

JP1

(underside)

1

LPT1

Game/MIDI Port

1

RT2





LPC I/O

IT8705

BIOS

Li

Battery

1

JAUD1

1

S

o

c

k

e

t 4

6

JP2

Fan1

2

RT1

CN8

VIA

KT400

Fan2

CD-In1



PCI 1

SW1

AGP 8X/4X

ON

DIP

1 2 3 4 5

PCI 2

PCI 3

PCI 4

PCI 5

IR

HDD/LED

PWR

--

++

1

9

JBAT1

Speaker

USB2

-

+

RST

1

PLED

9

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

1

9

PS/2 K/B



Mouse
(on top)

USB0

(on top)

USB1

(underside)

COM1

COM2

Line

Out

Line

In

MIC



ALC202A

AC'97
Codec

20

Chapter 2 Hardware Setup

2-3 AGP Slot Installation

The AGP slot on board supports 1.5V AGP 8X/4X card only. A Rib is
specifically added to the 8X/4X slot so as to match the AGP 8X/4X card.
To insert a 3.3V AGP 2X card into the AGP 4X slot will damage the
system chip and burn the 1.5V circuitry.
An AGP 8X card will support a data transfer rate up to 2GB/sec., while
an AGP 4X card will provide 1GB/sec transfer rate.

AGP Accelerator

notch

AGP 8X/4X Slot

JP1

(underside)

LPT1

Game/MIDI Port



ALC202A

AC'97
Codec



LPC I/O

IT8705

BIOS

Battery

1

1

S

o

c

k

e

t 4

6

JP2

1

Fan1

2

RT1

CN8

VIA

KT400

Fan2

CD-In1

1



RT2



PCI 1

PCI 2

PCI 3

SW1

AGP 8X/4X

ON

DIP

1 2 3 4 5

PCI 4

PCI 5

Li

IR

HDD/LED

PWR

--

++

1

9

JBAT1

Speaker

JAUD1

USB2

-

+

RST

1

PLED

9

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

1

9

PS/2 K/B

Mouse

(on top)



USB0

(on top)

USB1

(underside)

COM1

COM2

Line

Out

Line

In

MIC

21

KT400-C

2-4 IDE Connector Installation

To install IDE Connector, you may connect the blue connector of IDE
cable to the primary (IDE1) or secondary (IDE2) connector on board,
and then connect the gray connector to your slave device and the black
connector to your master device. If you install two hard disks, you must
configure the second drive to slave mode by setting its jumpers correctly.
Please refer to your hard disk documentation for the jumper settings.

JP1

PS/2 K/B

(on top)



USB0

(on top)

USB1

(underside)

COM1

COM2

Line

Line

MIC

Mouse

Out

In



ALC202A

AC'97
Codec

1

S

o

c

k

e

(underside)

1

LPT1

Game/MIDI Port

RT2



LPC I/O
IT8705

BIOS

Battery

1

JAUD1

JP2

Fan1

CN8

Fan2

CD-In1

1





Li

HDD/LED

--

++

1

9

JBAT1

Speaker

t 4

RT1

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

PWR

-

+

RST

1

PLED

Pin 1 (to Red Line)

6

VIA

KT400

USB2

2

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

ATA IDE connectors:

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

IDE1

Orient the red line on the IDE

IDE2

Flat Cable to Pin1.

Black Connector

(To Master Device)

Gray Connector

(To Slave Device)

Red Line

Blue Connector

(To Mainboard)

IDE Flat Cable

22

Chapter 2 Hardware Setup

2-5 Floppy Drive Connector ( FDC ) Installation

To install FDC, you should connect the end of FDC cable with single
connector to the board, and connect the other end with two connectors
to the floppy drives.

JP1

1

Mouse
(on top)

(underside)

PS/2 K/B



USB0

JP2

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

CD-In1

1



ALC202A



AC'97
Codec

RT2





LPC I/O
IT8705

BIOS

Li

Battery

1

JAUD1

S

o

c

k

e

t

4

6

2

Fan1

RT1

CN8

Fan2

PCI 1

SW1

VIA

KT400

AGP 8X/4X

ON

DIP

1 2 3 4 5

Clock

Generator

PCI 2

PCI 3

PCI 4

PCI 5

IR

HDD/LED

--

++

1

9

JBAT1

+

RST

Speaker

PLED

1

1

PWR

USB3

USB2

-

1

9

1

9

Pin 1 (to Red Line)

VIA

VT8235

1

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

IDE1

IDE2

Fan3

FDC1

Floppy Drive Connector:

Orient the red line of the
Floppy Flat Cable to Pin1.

To 1st Floppy Drive

Red line

FDD Cable

23

To 2nd Floppy Drive

To mainboard

KT400-C

2-6 ATX Power Supply Installation

JP1

1

Mouse
(on top)

(underside)

PS/2 K/B



USB0

JP2

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

CD-In1

1



ALC202A



AC'97
Codec

RT2





LPC I/O
IT8705

BIOS

Li

Battery

1

JAUD1

To set up Power Supply on this series:

1. Connect the on-board Main Power Connector (20-pin) to the Main
Power Connector (20-pin) of an ATX Power Supply which can be
either of the latest version 2.03 or of earlier ATX model.

S

o

c

k

e

t

4

6

2

Fan1

1

9

JBAT1

RT1

+12V

5SB

CN8

Fan2

HDD/LED

--

++

Speaker

VIA

KT400

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

PWR

USB2

-

+

RST

1

PLED

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

PWR OK

GND

+5V

GND

+5V

GND
+3.3V
+3.3V

Pin1

Main Power Connector

(20-pin)

+5V
+5V

-5V
GND

GND

GND
PS ON#
GND

-12V
+3.3V

Pin11

24

Chapter 2 Hardware Setup

2-7 Jumper / Switch Settings

The following diagrams show the locations and settings of jumper / switch
blocks on the mainboard.

Anti-burn Shield (ABSII)

JP1:

(Overheated CPU Shutdown)

(only for Athlon XP/Duron Morgan)

JP2:

Keyboard/Mouse

Power On / Wake Up

1-2 closed

KB/Mouse Power On /

1

Wake Up Enabled

2-3 closed

KB/Mouse Power On / Wake

1

Up Disabled

1

1

(default)

JBAT1

Clear CMOS

1-2 closed
(default)
To hold data

2-3 closed
To clear CMOS

1

Enable overheated CPU (85oC) shutdown function

1

1-2 closed (default)

2-3 closed

Disable overheated CPU shutdown function

JP1

1

Mouse

(on top)

(underside)

PS/2 K/B



USB0

JP2

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

CD-In1

1



ALC202A



AC'97
Codec

RT2





LPC I/O

IT8705

BIOS

Li

Battery

1

JAUD1

S

o

c

k

e

t

4

6

2

HDD/LED

++

Speaker

RT1

CN8

Fan2

--

VIA

KT400

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

PWR

USB2

-

+

RST

1

PLED

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

Fan1

1

9

JBAT1

SW1 (5-Dip)

On

Off

1 2 3 4 5

SW1 (5-Dip): CPU Clock/Overclock Select

CPU Clock SW1-1 SW1-2 SW1-3 SW1-4 SW1-5

100MHz Off On Off Off Off

(default)

133MHz On Off On Off Off

166MHz On Off On On On

25

KT400-C

2-7.1 How to tackle the Jumpers:

123

A 3-pin Jumper

If a pin-header (of 2 or more pins) is
designed in such a way that its pins
can be closed or linked together to
set up a specific function,
is called a jumper in this manual.

this header

A 2-pin
Jumper
Cap

The conductor inside the cap
links two header-pins together.

• A Jumper is usually but not necessarily given a “JpX” legend.

• In the Jumper setting diagram, all jumper pins covered with
black marks stand for closed pins with jumper cap.

1 13313

Jp X

Jumper with

Pin 2-3 closed

Jumper with

all pins open

Jumper with

Pin 1-2 closed

• Do not remove any jumper cap when power is on. Always
make sure the power is off before changing any jumper settings.
Otherwise, mainboard could be damaged.

2-7.2 SW1: CPU Clock/Overclock Select

SW1 is designed on board as a 5-dip switch for CPU clock select.

1. Before setting the CPU clock, read the Identification Legend on the
CPU, find the Max FSB and divide it by two. The result is the default
CPU clock.

2. Select the CPU clock you want from 100/133/166MHz and set SW1
to match your choice.

3. If you select a CPU clock which is higher than your default CPU
clock, it means that an overclock is desired. However, if an overclok
fails to boot system, you should restore the default setting and then
clear CMOS to rebooting your system. (See Clear CMOS in next
paragraph.)

SW1 (5-Dip)

SW1 (5-Dip): CPU Clock/Overclock Select

CPU Clock SW1-1 SW1-2 SW1-3 SW1-4 SW1-5

100MHz Off On Off Off Off

(default)

On

Off

1 2 3 4 5

133MHz On Off On Off Off

166MHz On Off On On On

26

Chapter 2 Hardware Setup

Further notes on CPU Overclocking:

1. If you have successfully booted system with or without CPU overclock,
you still can do another CPU overclock in BIOS Setup. Please enter
BIOS Setup, choose “Frequency/Voltage Control” menu, and take
the “Use Linear” option of the “Use CPU Linear Frequency”. Then
configure the “CPU Clock” item to raise your CPU clock.

2. CPU overclocking should take all components on board into account.
If you fail in BIOS overclocking, you will not be able to restart system.
In such case, power off system and clear CMOS by JBAT1 as stated
below and then restart your system. And remember to reconfigure
whatever should be reconfigured.

3. If your system is already fixed in a cabinet or case, you may not like
to take the trouble to clear CMOS. Then power on your system with
the power button on the case and simultaneously press down the
“Insert” key of the keyboard until you see the initial bootup screen
appear. And remember you should also enter CMOS BIOS Setup
and choose “Load Optimized Defaults” to restore default BIOS .

2-7.3 JBAT1: Clear CMOS

When you have problem with rebooting your system, you can clear
CMOS data and restore it to default value. To clear CMOS with Jumper
JBAT1, please follow the steps below:

1. Power off system.

2. Set JBAT1 to Pin 2-3 closed.

3. After 2 or 3 seconds, return the JBAT1 setting to Pin1-2 closed.

4. CMOS data are restored to default. Remember never clear CMOS
when system power is on.

JBAT1

Clear CMOS

1

1-2 closed
(default)
To hold data

1

2-3 closed
To clear CMOS

27

KT400-C

2-7.4 Jp1: Anti-burn Shield (ABSII)

Anti-burn Shield (ABSII)

(Overheated CPU Shutdown)

(only for Athlon XP/
Duron Morgan)

1-2 closed (default)

1

Enable overheated CPU
(85oC) shutdown function

1

2-3 closed

Disable overheated CPU
shutdown function

JP1 is designed to enable the overheat safeguard for some CPUs which

JP1:

are incorporated with a protective thermal diode.

The latest AMD Athlon
XP and Duron Morgan CPUs are incorporated with such thermal diode
and can be protected by this function. Setting JP1 1-2 closed (default
setting) will get system shutdown when any of the above-mentioned
CPUs gets to 85oC (the default protection temperature.) Only when the
CPU returns to a cooler state can you restart your system.
For other CPUs that are not incorporated with a protective thermal diode,
please set JP1 2-3 closed to disable the function because it is a vain
design now.

Reminder: If a sudden shutdown happens to your system which has
been running well for a while with an AMD Athlon XP/Duron Morgan
CPU, this might be caused by the “Overheated CPU Shutdown” design.
Please use a better CPU cooling fan to restart your system.

28

Chapter 2 Hardware Setup

2-7.5 JP2: KB/Mouse Power On / Wake Up

JP2 is designed on board as a jumper to enable/disable the PS/2 key­board/mouse Power On/Wake Up from system off or suspend mode.
Yet users should still enter BIOS setup to choose the Wake Up/ Power
On mode.
USB keyboard/mouse Wake Up function is not supported in this
mainboard.

JP2:

Keyboard/Mouse

Power On / Wake Up

1-2 closed

KB/Mouse Power On /

1

Wake Up Enabled

2-3 closed

KB/Mouse Power On / Wake

1

Up Disabled

(default)

29

KT400-C

2-8 Other Connectors Configuration

This section lists out all connectors configurations for users’ reference.

2-8.1 On-board FAN Connectors

JP1

1

Mouse
(on top)

(underside)

PS/2 K/B



USB0

JP2

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

CD-In1

1



ALC202A



AC'97
Codec

RT2





LPC I/O
IT8705

BIOS

Li

Battery

1

JAUD1

S

o

c

k

e

t

4

6

2

Fan1

1

9

JBAT1

RT1

CN8

Fan2

HDD/LED

--

++

Speaker

VIA

KT400

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

PWR

USB2

-

+

RST

1

PLED

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

GND
+12V
SENSOR

Sensor Conn.

FAN1, Sensor Fan Connector
(Yellow)

FAN2, Sensor Fan Connector
(Yellow)

FAN3, No-sensor Fan Connector

Void

+12V

GND

No Sensor

Both Sensor and No-sensor Fan Connectors support CPU/AGP/Sys­tem/Case cooling fan with +12V mode. When connecting the wire to
any Fan Connector, user should make sure that the red wire is for the
positive current and should be connected to pin +12V, and the black
wire is Ground and should be connected to pin GND. A Hardware Moni­tor chipset is on board, with which user can install a Hardware Monitor
Utility and read the fan speed transmitted from the sensor fan connector.
Otherwise, user can read the fan speed from the “Hardware Monitor
Status” in CMOS BIOS.

A running fan will send out 2 electric pulses per rotation of its fan
blade to a Sensor Fan Connector which in turn will count the electric
pulses and send the information to the System Hardware Monitor. The
hardware Monitor Program will work out the fan rotation speed and dis­play it on screen.

30

Chapter 2 Hardware Setup

2-8.2 USB Ports and USB Pin-headers

This series provides two USB ports USB0 and USB1 on board sup­porting various USB devices. In addition, two USB pin-headers are
added on board to provide expansion of four more optional USB ports
by using two additional USB Cables. User can order the optional USB
cables from your mainboard dealer or vender.

When plugging the USB cable to USB Header, user must make sure
the red wire is connected to Pin 1.

All 6 USB ports are compliant with 1.0 / 2.0 USB Bus. USB 2.0 sup­ports Win 98 and above. USB 1.0 / 2.0 drivers are provided in Support
CD for user’s installation.

USB connectors USB0 and USB1 (underside)

JP1

1

Mouse

(on top)

(underside)

PS/2 K/B



USB0

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

1



ALC202A

AC'97
Codec

RT2





LPC I/O
IT8705

BIOS

Li

Battery

1

JAUD1

Socket 462

JP2

Fan1

CD-In1



9

JBAT1

RT1

CN8

VIA

KT400

Fan2

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

HDD/LED

PWR

--

USB2

++

1

-

+

RST

Speaker

1

PLED

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

USB Pin-headers USB2 and USB3

USB Cable (Optional)

USB Port

Red wire

1

1

10

10

First USB Port Wiring for Front USB

USB Header

Pin Assignment

Second USB Port Wiring for Front USB

Red White

+5V

1

+5V
Red

D1-

D2-

White

Green

D1+

D2+

Green

31

black
GND

GND
black

10

KT400-C

2-8.3 Chassis Panel Connectors

A.

B. C. D.

E. F. G. H. I. J. K.

A: PS/2 Mouse

B : Port USB 0

C: LPT1 PORT

D: Game/MIDI

E: PS/2 Keyboard

F: USB 1 (Underside)

G: COM 1
H: COM 2
I: Line Out
J: Line In
K: Microphone Input

2-8.4 PS/2 Mouse and PS/2 Keyboard

(PS/2 Mouse: On top of keyboard connector, Green Color)

6

Void

Vcc

4

2

Mouse Clock

5

GND

3

1

Mouse DataVoid

Keyboard Clock

Void

Vcc

Void

6

4

2

5

GND

3

Keyboard Data

1

(PS/2 Keyboard Connector: Underside, Purple Color)

32

Chapter 2 Hardware Setup

2-8.5 CD-ROM Audio Connectors (CD-In1)

CD-In1 is an audio connector connecting CD-ROM audio to mainboard.

JP1

1

Mouse

(on top)

(underside)

PS/2 K/B



USB0

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

1



ALC202A

AC'97
Codec

RT2



LPC I/O
IT8705

BIOS

Battery

1

JAUD1

Socket 462

JP2

Fan1

CD-In1





Li

9

RT1

CN8

VIA

KT400

Fan2

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

HDD/LED

PWR

--

USB2

++

1

JBAT1

-

+

RST

Speaker

1

PLED

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

CD-ROM Audio Connector

CD-In1

1

Pin 1

Pin 2

Pin 3

Pin 4

Pin Signal

Left Channel

GND

GND

Right Channel

33

KT400-C

2-8.6 Thermal Connectors

JP1

(underside)

1

LPT1

Game/MIDI Port

CD-In1

1

RT2





LPC I/O

IT8705

BIOS

Li

Battery

1

JAUD1

1

S

o

c

k

e

t

4

6

PCI 1

SW1

RT1

KT400

AGP 8X/4X

ON

1 2 3 4 5

2

VIA

DIP

Generator

JP2

Fan1

CN8

Fan2



PCI 2

PCI 3

PCI 4

PCI 5

IR

HDD/LED

PWR

--

++

1

9

JBAT1

+

RST

Speaker

PLED

USB3

USB2

-

1

9

1

PS/2 K/B



(on top)

(underside)

COM2

Line

Line

Mouse

(on top)

USB0

USB1

COM1

Out

In

MIC



ALC202A

AC'97
Codec

Clock

1

1

9

VIA

VT8235

IDE1

1

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

IDE2

Fan3

FDC1

RT1

RT1 is mounted
with Thermal Resistor
by default.

RT2

To Devices

To RT2

Thermal Cable

(Optional)

1. Connector RT1: A thermal resistor is mounted by default to connector

RT1 so as to detect the temperature of the CPU. What RT1 does is
to transmit the thermal signal to BIOS or Hardware Monitor.

2. Connector RT2: A thermal cable is needed to connect RT2 to on-

board devices such as HDD, Graphics card etc., so as to detect the
temperature generated therein. Please connect the end (a) of the
thermal cable to RT2, and tape another end (b) of the thermal cable
on to the device which you want to monitor. After you have finished
the thermal cable installation, you will see the detected temperature

in BIOS setup or Hardware Monitor utility.

34

Chapter 2 Hardware Setup

2-8.7 Complex Pin-header (Front Panel Connectors)

This complex Pin-header consists of the following connectors for vari­ous front panel supports. When you have fixed the mainboard to the
case, join the connectors of this Complex Pin-header to the case Front
Panel.

JP1

1

Mouse
(on top)

(underside)

PS/2 K/B



USB0

(on top)

1

USB1

(underside)

COM1

LPT1

COM2

Line

Out

Line

In

Game/MIDI Port

MIC

CD-In1

1



ALC202A

AC'97
Codec

RT2





LPC I/O

IT8705

BIOS

Li

Battery

1

JAUD1

S

o

c

k

e

t

4

6

JP2

Fan1

CN8

Fan2



HDD/LED

++

1

9

JBAT1

Speaker

2

RT1

VIA

KT400

AGP 8X/4X

ON

SW1

1 2 3 4 5

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

IR

PWR

--

USB2

-

+

RST

1

PLED

DDR 400/333/266 MHz

(DDR 400MHz CONDITIONALLY SUPPORTED)

DIMM2

DIMM1

DIP

Clock

Generator

VIA

VT8235

IDE1

1

IDE2

1

Fan3

FDC1

USB3

1

9

1

9

Case
Front Panel

Power
Switch

2

Power Switch

3

Infrared(IR)

2nd HDD LED

4

1st HDD LED

(Optional)

1

SMI

ATX POWER SWITCH

NO CONNECTION

INFRARED TRANSMIT SIGNAL

INFRARED TRANSMIT SIGNAL

Logic High
HDD LED SIGNAL
HDD LED SIGNAL

Logic High

GND

SMI SIGNAL

Vcc

Vcc

GND

(+)

(-)
(-)

(+)

SPEAKER SIGNAL

35

GND
SUSPEND LED SIGNAL

GND
KLOCK

Keylock

GND
NO CONNECTION

Vcc

GND
RESET SIGNAL

NO CONNECTION
GND
Vcc

Suspend LED

(Optional)

(Optional)

6

Power LED

Reset Switch

Speaker

5

7

8

9

KT400-C

(1) SMI Connector (Optional):

Connectedion: Connected to the Suspend Switch.
Function: Manually selecting DOS system into the Suspend Mode
or “Green Mode” by System Mangement Interupt.

(2) Power Switch Connector:

Connectedion: Connected to a momentary button or switch.
Function: Manually switching the system between “On” and “Soft
Off”. Pressing the momentary button for more than 4 seconds will
also turn the system off.

(3) IR Connector (Infrared Connector):

Connectedion: Connected to Connector IR on board.
Function: To support wireless transmitting and receiving

on board.

module

(4) 1st HDD LED Connector/2nd HDD LED Connector:

Connectedion: Connected to HDD LED.
Function: To supply power to HDD LED.

(5) Suspend LED Connector (Optional):

Connectedion: Connected to Suspend Indicator.
Function: To supply power to “Suspend Indicator”.

(6) Keylock Connector (Optional):

Connectedion: Connected to keyboard.
Function: To lock keyboard and disable keyboard function.

(7) Power LED Connector:

Connectedion: Connected to System Power LED.
Function: To supply power to “System Power LED”.

(8) Reset Switch Connector:

Connectedion: Connected to “Reset Switch”.

Function: To supply power to “Reset Switch” and support
system reboot function.

(9) Speaker Connector:

Connectedion: Connected to the case-mounted Speaker.
Function: To supply power to the case-mounted Speaker.

36

Chapter 2 Hardware Setup

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

VIA

KT400

IDE1

IDE2

Li

Battery

Fan3

VIA

VT8235

FDC1

COM1

COM2

LPT1

MIC

Line

Out

Line

In

Game/MIDI Port

AGP 8X/4X

Clock
Generator

JBAT1

Speaker

RST

PLED

HDD/LED

IR

PWR

++

--

+

-

USB3

1

CN8

DIMM1

DDR 400/333/266 MHz



USB1

PS/2 K/B

Mouse
(on top)

(underside)

Fan1

1

JP2

1

JP1

Socket 462

USB2

1

9

9





LPC I/O
IT8705

RT2



1

CD-In1



AC'97
Codec

JAUD1

BIOS

1

9

1

ALC202A

Fan2

SW1

ON

DIP

1 2 3 4 5

DIMM2

(underside)

(on top)

USB0

RT1

1

1

1

(DDR 400MHz CONDITIONALLY SUPPORTED)

2-8.8 JAUD1: Front Panel Audio Connector (optional)

This Mainboard is designed with a Front Panel Audio connector “JAUD1”
which provides connection to your chassis.

1. When JAUD1 is set to 5-6 closed and 9-10 closed, this default setting
disables this connector and leaves the Back Panel Audio enabled.

2. To use this Front Panel Audio Connector, please open all pins of
JAUD1 and connect it to the Front Panel Audio Connector.

JAUD1: Front Audio Connector

2

1

10

9

Pin 1 Mic In
Pin 3 Mic VREF
Pin 5 FPOUT R
Pin 7 (Key)
Pin 9 FPOUT L

Pin 2 Aud GND
Pin 4 Aud Vcc
Pin 6 RET R
Pin 8 (Void)
Pin10 RET L

37

KT400-C

Chapter 3 Software Setup

Drivers, Utilities and Software Installation

Support CD:
This mainboard will be shipped with a Support CD which contains those
necessary driver files, Application Softwares and some helpful utilities.
It is a user-friendly, auto-run CD which will open itself up in a CD-ROM
automatically.

Contents of Support CD:
For this mainboard, user will be able to find in the Support CD the fol­lowing drivers and utilities:

1. VIA 4-in-1 Drivers

2. AC’97 Audio Drivers

3. VIA USB 2.0 Drivers

4. Hardware Monitor Utility

5. Other drivers (including LAN drivers)

This chapter is devoted to describing the installations of all these
essential drivers and utilities on Windows 9X, Windows ME , Windows
2000 and Windows XP. The installation procedures for all these oper­ating systems are programed into an auto-run mode. What users have
to do is read and follow the pop-up instructions. We therefore take the
installation on Windows 98 as the general illustration hereby.

The priority of driver installation should also be noted. Users are rec­ommended to take the following installation order:

3-1 Open Support CD and choose your drivers
3-2 VIA 4-in-1 Drivers Installation
3-3 AC’97 Audio Drivers Installation
3-4 USB 2.0 Drivers Installation
3-5 Hardware Monitor Utility Installation

38

Chapter 3 Software Setup

3-1 Open Up Support CD:

1. Please put the Support CD enclosed in your mainboard package

into the CD-ROM drive. In a few seconds, the Main Menu will
automatic ally appear, displaying the contents to be installed for this
series:

2. In case your system does not open the Support CD automatically,

please click to the following path to enter the Main Installation Menu:

D:\ Autorun.exe (assuming that your CD-ROM Drive is Drive D)

3. Users are recommended to install all the drivers and utilities at a

time, though they can be installed separately.

Also, we should take “VIA 4-in-1 Drivers” as first installation priority

to optimize the VIA system.
From next section, we provide detailed descriptions of all these
installations with graphical illustrations.

39

KT400-C

3-2 Proceed to VIA 4-IN-1 Drivers Installation

1. Following the procedures of opening the Support CD, click to “ VIA 4-

in-1 Drivers” to proceed.

2.The VIA Service Pack

InstallShield Wizard will pop up
to guide you to the VIA Service
pack installation. Click “Next”
button to continue.

Next Yes

4. On the screen below, check

”Normally Install” and click
“Next” to continue. (If you check
“Quickly Install”, you will skip
the detailed procedures of the
VIA 4-in-1 Setup.)

3. “VIA Service Pack README”
screen will appear, please click
the “Yes” button to agree with
the Licence Agreement and
continue.

5. Select the checkbox as below
and click “Next” to continue:

VIA ATAPI Vendor Support Driver
AGP Driver (AGP3.0 Supported)
IRQ Routing Miniport Driver
VIA INF Driver’1.70a

Next

Next

40

Chapter 3 Software Setup

6. Select “Install VIA ATAPI
Vendor Support Driver”
checkbox, then click the “Next”
button to continue.

Next

8. Select “Install VIA AGP Driver”
and press “Next” button to
continue.

Next

7. Click on “Click to enable DMA
Mode” checkbox to enable
DMA function, then click the
“Next” button to continue.

Next

9. Select “Install VIA IRQ Routing
Miniport Driver” checkbox, then
click the “Next” button to
continue.

Next

10. After all these setup procedures have finished, you should restart
your computer by clicking on “OK” so as to put VIA 4-in-1 drivers

into effect and proceed to second driver installation.

OK

41

KT400-C

3-3 Proceed to AC’97 Audio Driver Installation

1 Following the installation of VIA 4in1 drivers, you have to restart

system so that your system can be reconfigured with VIA 4in1. When
restarting procedures finish, please open the Support CD with your
CD-ROM to enter the Main Installation Menu. Then click to “Install
AC97 Audio Driver”.

2 The Realtek AC’97 Audio Setup
InstallShield Wizard will pop up
to guide you to the Realtek AC’97

Audio Driver installation. Press
“Next” button to continue.

kÉñí

3 After all setup procedures
have completed, click to “Finish”
button to restart your computer

and it will take into effect after
rebooting up.

cбеблЬ

42

Chapter 3 Software Setup

3-4 Install USB 2.0 Driver for Win98 / Me / 2000 / XP

VIA USB V2.0 is already integrated on board. Its 480Mb/s transfer rate
supports operating system Win98/Me/2000/XP. USB Driver installa­tion procedures are of similar steps in these systems. Please take the
following illustrations from Win XP as the USB driver installation guide:

1. Following the procedures of opening the Support CD, click to
“Motherboard Drivers” and then choose “VIA USB 2.0 Driver” to
proceed. Please notice that the USB card driver is different from the
USB 2.0 driver typically for the on-board USB. Do not use the USB
card driver here.

2. Instantly the “USB 2.0 Setup Program” will pop up on screen. Click
“Next” to continue.

43

Next

KT400-C

3. Instantly, next screen will pop up to prompt you to select component.
Select “Install USB Driver” and click “Next” button to continue.

Next

4. The USB 2.0 Setup Program will then guide you through the whole
driver setup (including the acceptance of License Agreement)until
the “Finish” screen appears to prompt you to restart your system.
Please click “Finish” button to restart system to put the new driver
into effect.

44

Finish

Chapter 3 Software Setup

3-5 To Install Hardware Monitor Utility

3-5.1 Installation

Hardware Monitor is built on this mainboard. Its installation is pro-

gramed to a fully automated mode on Windows 9X/Me/NT4/2000/
XP. User can follow the model installation below for its installation
on various Windows System.

1.Following the procedures of opening the Support CD, click to “

Hardware Monitor Utility” to proceed.

2.Then the installation program

automatically opens the
“Soltek HM Setup” screen.

Click “OK” to continue.

`äáÅâ

3.Select the Program folder

and click “Install” to continue.

4.In a few seconds, the instal-

lation completes. Click the
“Finish” button to complete
the driver utility setup.

`äáÅâ

`äáÅâ

45

KT400-C

3-5.2 Verification

1. After installing Soltek Hardware
Monitor, double click “SoltekHM”
icon on the desktop to open the main
window of the Soltek Hardware
Doctor.

2.Then the pop-up screen will show all information about CPU

Temperature, Fan Speed and various Voltages.

Showing the Fan Speed(s) that

Showing the temperature(s), the
function of which is supported by
the mainboard.

is supported by the mainboard.

Click on “Soltek” button to
display the function menu.

Showing the Voltage(s) that is
supported by the mainboard.

Status Warning LED

*Note: Not all items or functions showing in the above picture will
show up. Only those items or functions that are supported
by the mainboard will reveal themselves in the above
screen.

46

KT400-C

Chapter 4 AMI BIOS Setup

THE BIOS

BIOS stands for Basic Input and Output System. It was once called
ROM BIOS when it was stored in a Read-Only Memory (ROM) chip
Now manufacturers would like to store BIOS in EEPROM which means
Electrically Erasable Programmable Memory. BIOS used in this series
of mainboard is stored in EEPROM, and is the first program to run when
you turn on your computer.

BIOS performs the following functions:

1. Initializing and testing hardware in your computer (a process called
“POST”, for Power On Self Test).

2. Loading and running your operating system.

3. Helping your operating system and application programs manage
your PC hardware by means of a set of routines called BIOS Run­Time Service.

This Chapter includes the following topics :
4-1 About BIOS Setup
4-2 To Run BIOS Setup
4-3 About CMOS
4-4 The POST (Power On Self Test)
4-5 To Update BIOS
4-6 BIOS Setup

48

Chapter 4 BIOS Setup

4-1 About BIOS Setup

BIOS setup is an interactive BIOS program that you need to run when:

1. Changing the hardware of your system. (For example: installing a
new Hard Disk etc.)

2. Modifying the behavior of your computer. (For example: changing
the system time or date, or turning special features on or off etc.)

3. Enhancing your computer’s behavior. (For example: speeding up
performance by turning on shadowing or cache)

4-2 To Run BIOS Setup

First access BIOS setup menu by pressing < DEL > key after “POST” is
complete ( before OS is loaded ). BIOS will then display the following
message:

DEL:SETUP

4-3 About CMOS

CMOS is the memory maintained by a battery. CMOS is used to store
the BIOS settings you have selected in BIOS Setup. CMOS also
maintains the internal clock. Every time you turn on your computer, the
BIOS looks into CMOS for the settings you have selected and configures
your computer accordingly. If the battery runs out of power, the CMOS
data will be lost and POST will issue a “CMOS invalid” or “CMOS
checksum invalid” message. If this happens, you have to replace the
battery and check and configure the BIOS Setup for the new start.

4-4 The POST ( Power On Self Test )

POST is an acronym for Power On Self Test. This program will test all
things the BIOS does before the operating system is started. Each of
POST routines is assigned a POST code, a unique number which is
sent to I/O port 080h before the routine is executed.

49

KT400-C

4-5 To Update BIOS

• System BIOS is incorporated into a Flash memory component. Flash

BIOS allows user to upgrade BIOS without the need to replace an EPROM
component.

• The Upgrade Utility can be loaded on a floppy diskette for upgrading

saving, and verifying the system BIOS. The Update Utility can also be
run from a hard disk drive or a network drive.

• It is highly recommended that you save a copy of the original mainboard

BIOS along with a Flash EPROM Programming utility (AMIXXX.EXE)to a
bootable floppy disk so that you can reinstall the BIOS when in need.

• Normally, to update BIOS is unnecessary if the system is working fine.

Users should only update BIOS when incompatible problems are encoun­tered or new features have to be added to system.

• “AMIFLASH.EXE” is a Flash EPROM Programming utility that updates

the BIOS by uploading a new BIOS file to the programmable flash ROM
on the mainboard. This program only works in DOS environment, the

utility can not be executed in win95/98, ME, NT WINDOWS 2000 or
Windows XP environment.

• Please follow the steps below for updating the sys­ tem BIOS:

Step 1. Please visit the board maker’s website, download latest BIOS
file and AMI update utility. The file name of AMI update utility will be
“AMIXXX.EXE” of which “ XXX ” stands for the version number of the
file. The BIOS file format will be *.ROM, of which “ * ” stands for the
specific BIOS file name.

Step 2. Create a bootable diskette. Then copy the BIOS file and AMI
flash utility “AMIXXX.EXE” into the diskette.

Step 3. Insert the diskette into drive A, boot your system from the
diskette.

50

Chapter 4 BIOS Setup

Step 4. Type AMIFLASH *.ROM and then press <Enter> to run BIOS
update program. (*.ROM will vary, depending on your mainboard model
and version code. Instead of typing “*”, you should type specific file
name for your specific mainboard. For example: AMIFLASH(space)
75FRV11.ROM).

Step 5. When the message “Flash ROM Update Completed - Pass.”
appears, please restart your system.

Step 6. You will see a message “CMOS Memory Size Wrong” during
booting the system. Press <Del> or <F1> to run CMOS setup utility,
then reload “LOAD SETUP DEFAULTS” or “Load Optimal Defaults”
and save this change.

51

KT400-C

4-6 BIOS SETUP --- CMOS Setup Utility

4-6.1 CMOS Setup Utility

This mainboard comes with the AMI BIOS from American Megatrends
Inc. Enter the CMOS Setup Utility Main Menu by:

1. Turn on or reboot your system. After a series of diagnostic checks,
the following message will appear:

PRESS <Del> TO RUN SETUP

2. Press the <Del> key and the main program screen will appear as
follows.

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Power Management Features

PNP/PCI Configurations

Integrated Peripherals

SmartDoc Anti-burn Shield

Frequency/Voltage Control

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Exit : Select Menu Enter: Select Sub-Menu F10: Save and Exit

Set Time, Date, Hard Disk Type ...

System Information

Set Supervisor Password

Load Optimal Defaults

Save & Exit Setup

Exit Without Saving

3. Use the arrow keys on your keyboard to select an option, and press
<Enter>. Modify the system parameters to reflect the options installed
in your system.

4. You may return to the Main Menu anytime by pressing <ESC>.

5. In the Main Menu, “Save & Exit Setup” saves your changes and
reboots the system, and “Exit Without Saving” ignores your changes
and exits the program.

52

Chapter 4 BIOS Setup

4-6.2 Standard CMOS Setup

Standard CMOS Setup records some basic system hardware
configuration and sets the system clock and error handling. Modify the
configuration values of this option if you want to change your system
hardware configuration or after you clear CMOS data.

Run the Standard CMOS Setup as follows:

1. Choose “Standard CMOS Setup” from the Main Menu and a screen
with a list of options will appear:

Standard CMOS Features Setup Help

System Time 00 19 29
System Date Dec 05 2002 Thr

Floppy options.
IDE Device Config

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

53

KT400-C

System Time The BIOS shows the time of the day in the format:

hh:mm:ss. Choose the field with the Arrow keys
and change the time with the Page Up/Page
Down +/- keys.

System Date The BIOS shows the date of the day in the format:

mm:dd:yy :day of the Week. Choose the field with
the Arrow keys and change the value with the
Page Up/Page Down +/- keys.

Floppy options Press Enter on “Floppy options” will let you select

this field to the type(s) of floppy disk drive(s) installed
in your system. The choices are:

1.2MB, 5.25 in.
720KB, 3.5 in.

1.44MB, 3.5 in.

2.88MB, 3.5 in.
Not Installed

IDE Device Config Press Enter on IDE Device Config will let you

configure the IDE devices on board and the fol­lowing menu will reveal the following submenu
for your configuration of the hard Disk you have
installed:

Primary IDE Master : Not Installed Setup Help

Type Auto
Cylinders
Heads
Write Precompensation
Sectors
Maxium Capacity 0 Mb
LBA Mode Off
Black Mode Off
Fast Programmed I/O Modes 0
32 Bit Transfer Mode Off

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

54

Chapter 4 BIOS Setup

Type This option shows the types of configuration for the

IDE devices:
1-50: Predefined types
USER: set Parameters by User
Auto: Set parameters automatically
CD-ROM: Use for ATAPI CD-ROM drives
Double click [Auto] to set all HDD parameters
automatically, including “Cylinders, Heads, Write
Precompensation, Sectors, Maximum Capacity and
32 Bit Transfer Mode.

55

KT400-C

4-6.3 Advanced BIOS Features

Advanced BIOS Features improves your system performance or sets
up system features according to your preference.

Run the Advanced BIOS Features as follows:

1. Choose “Advanced BIOS Features” from the Main Menu and a screen
with a list of options will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

Advanced BIOS Features

Quick Boot Enabled
Delay for Hard Drive (Sec.) 2
Boot Device Priority
1st Floppy: 1.44 MB 3.5
2nd CD-ROM
3rd IDE-0 :Maxtor 20560 A4 ­Try Other Boot Devices Yes
Initial Display Mode Silent
Display Mode at Add-On ROM Init Force BIOS
S.M.A.R.T for Hard Disks Disabled
Bootup Num-lock On
Floppy Drive Swap Disabled
Floppy Drive Seek Disabled
Primary Display VGA/EGA
Password Check Setup
Boot To OS/2 No
L1 Cache Writeback
L2 Cache Enabled
System BIOS Cacheable Enabled
C000,32K Shadow Cached
C800,16K Shadow Disabled
CC00,16K Shadow Disabled
D000,16K Shadow Disabled
D400,16K Shadow Disabled
D800,16K Shadow Disabled
DC00,16K Shadow Disabled

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

Setup Help

56

Chapter 4 BIOS Setup

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide.

Quick Boot

Delay for Hard Drive

(Sec.)

1st/2nd/3rd Boot

Device

Try Other Boot De-

vices

Initial Display Mode

Display Mode at Add-

On ROM Init

S.M.A.R.T. for Hard

Disks

Allows you to enable / disable quick boot of your
system.

Allows you to adjust the time of detecting hard disk
on board at booting system.
Choices: Disabled; 1~10 sec. in 1 sec. stepping.

Allows you to set floppy or IDE devices already in­stalled on board to be the 1st/2nd/3rd boot device.
Choises: Disabled; Device(s) installed

Allows you to enable/disable system to try to boot
with other boot devices.
Choises: Yes; No

If option is “Silent”, the initial display mode is set to
one with Soltek logo. If option is “BIOS”, initial dis­play will hide logo.
Choices: Silent (default); BIOS

If the item “Initial Display Mode” is set to “Silent”, two
other sub-modes are provided for this item. If “Force
BIOS” is chosen, the vendor’s logo screen will be fol­lowed by the “Add-on ROM” initial screen (the screen
showing the add-on card BIOS message). If “Keep Cur­rent” is chosen, no “Add-On ROM” screen is followed.

Allows you to enable / disable the Self Monitoring
Analysis and Reporting Technology for the hard disk.
Choices: Enabled; Disabled

57

KT400-C

Bootup Num-lock Allows you to toggle between On or Off to control

the state of the NumLock keys when the system
boots. If On, the numeric keypad is in numeric
mode. If off, the numeric keypad is in cursor con­trol mode.

Floppy Drive Swap

Floppy Drive Seek

Primary Display Allows you to choose the primary display for the system.

Password Check Allows you to set BIOS to check up password with a

Boot to OS/2 Allows you to set your system to OS/2 operating

L1 Cache Allows you to set the Internal/External Cache Mode.

L2 Cache

System BIOS

Cacheable

Disabled (default), Floopy Drive A will not be chnged to
B, nor B to A. Enabled, Floppy Drive a and B will change
position.

Disabled (default), Floppy Drives will not be checked and
diagnosed at system bootup; Enabled, Floppy Drives
will be checked and diagnosed at system bootup.

Choices: VGA/EGA (default); CGA40x25; CGA80x25;
Mono; Absent

password prompt at BIOS Setup or whenever re­starting system.
Choices: Setup; Always

system.
Choices: Yes; No (default)

Choices: WriteBack; WriteThru; Disabled
Allows you to set the Internal/External Cache Mode.

Choices: Enabled; Disabled

Allows you to enable / disable the System BIOS
Cacheable function.

C000, 32K Shadow Allows you to set these addresses cached, Enabled or

Disabled. Default: Cached

C800,CC00,D000,D400,

D800,DC00 16K

Shadow

Allows you to set these addresses cached, Enabled or
Disabled. Default: Disabled

58

Chapter 4 BIOS Setup

4-6.4 Advanced Chipset Features

Advanced Chipset Features is used to modify the values of chipset
buffers. These buffers control the system options.

Run the Advanced Chipset Features as follows:

1. Choose “Advanced Chipset Features” from the Main Menu and a

list of option will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

Advanced Chipset Features Setup Help

DRAM Timing
Configure SDRAM Timing by SPD Enabled
SDRAM Frequency Auto
SDRAM CAS# Latency 2.5
SDRAM Bank Interleave Disabled

SDRAM Burst Length 4 QW
SDRAM Command Rate 2T
Fast Command Normal
AGP Mode 8X
AGP Fast Write Disabled
AGP Aperture Size 64MB
AGP Master 1 W/S Write Disabled
AGP Master 1 W/S Read Disabled
AGP Read Synchronization Disabled
APIC Interrupt Mode Enabled
USB Controller 6 USB Ports
USB 1.1 Device Legacy Support Disabled
USB 1.1 Port 64/60 Emulation Disabled

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

59

KT400-C

Configure SDRAM

Timing by SPD

SDRAM Frequency Allows you to set the SDRAM frequency.

SDRAM CAS# Latency With SDRAM Timing by SPD disabled, you can se-

SDRAM Bank Inter-

SDRAM Burst Length With SDRAM Timing by SPD disabled, you can se-

SDRAM Command

SPD (Serial presence detect) is a device in memory
module for storing the module information such as
DRAM timing and chip parameters. If this option is
enabled, BIOS will access SPD automatically to
configure module timing. If disabled, DRAM timing
can be configured manually.

Choices: Auto; 200MHz; 266MHz; 333MHz; 400MHz

lect the SDRAM CAS# (Column Address Strode)la­tency manually.
Choices: 1.5 Clocks; 2 Clocks; 2.5 Clocks; 3 Clocks

This item allows you to enable / disable SDRAM

leave

Bank Interleave function.
Choices: Disabled (default); 2-Way; 4-Way

lect the SDRAM Burst length manually.
Choices: 8 QW; 4 QW

Allows you to set the SDRAM Command Rate.

Rate

Choices: 1T; 2T

Fast Command Allows you to select SDRAM Command Mode.

Choices: Normal; Fast; Ultra

AGP Mode Allows you to see the AGP Mode on board. The

default setting is Auto. This item supports 4X/8X AGP
Mode. 2X and 1X modes are included in options for
attempt to lower the AGP speed.

AGP Fast Write Allows you to enable / disable the AGP Fast Write

function

60

Chapter 4 BIOS Setup

AGP Aperture Size Allows you to set the AGP Aperture Size.

Choices: 4MB; 8MB; 16MB; 32MB; 64MB; 128MB;
256MB;

AGP Master 1 W/S

Write

AGP Master 1 W/S

Read

AGP Read Synchroni-

zation

APIC Interrupt Mode

USB Controller Allows you to set the USB Controller on the USB

USB 1.1 Device Legacy

Support

USB 1.1 Port 64/60

Emulation

Allows you to enable / disable (default) the support
of AGP Master 1 Waite State Write.

Allows you to enable / disable (default) the support
of AGP Master 1 Waite State Read.

Allows you to enable / disable (default) the AGP
Read Synchronization function.

Allows you to enable (default) / disable the APIC
function for selecting the APIC interrupt Mode.

port(s).
Choices: 6 USB Ports; 4 USB Ports;
2 USB Ports; disabled

Allows you to select the USB Device Legacy support.
Choices: No Mice; all Devices; Disabled

Allows you to enable / disable (default) the Port 64/
60 Emulation.

61

KT400-C

4-6.5 Power Management Features

Power Management Features allows you to set the system’s power
saving functions.

Run the Power Management Features as follows:

1. Choose “Power Management Features” from the Main Menu and a
list of options will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

Power Management Features Setup Help

ACPI Standby State S1/POS
Power Management/APM Enabled
Video Power Down Mode Suspend
Hard Disk Power Down Mode Stand By
Standby Time Out (Minute) Disabled
Suspend Time Out (Minute) Disabled
Power Button Function On/Off
Restore on AC/Power Loss Last State
Resume On PME# Disabled
Resume On PS/2 KB Disabled
Wake-Up Key Any Key
Resume On PS/2 Mouse Disabled
Resume On RTC Alarm Disabled
RTC Alarm Date 15
RTC Alarm Hour 12
RTC Alarm Minute 30

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

62

Chapter 4 BIOS Setup

ACPI Standby State This item allows you to select the ACPI Suspend

type. You can select S3(STR) for suspending to
DRAM if your system supports this mode. Or you
can select S1 (POS) for Power on Suspend under
Windows 98 or later O/S ACPI mode..

Power Management/

Allows you to enable / disable the Power manage­ment / Advanced Power Management function.

APM

Video Power Down

Hard Disk Power

Down Mode

Standby Time Out

(Minute)

Suspend Time Out

(Minute)

Power Button Function Allows you to set Power Button function.

Restore on AC/Power

Resume on PME#

Resume on PS/2 KB

Allows you to select the Video Power Down Mode.

Mode

Choices: Disabled; Stand By; Suspend

Allows you to select the Hard Disk Power Down
Mode.
Choices: Disabled; Stand By; Suspend

To set the duration of Standby Time Out.
Choices: 1; 2; 4; 8; 10; 20; 30; 40; 50; 60

To set the duration of Suspend Time Out.
Choices: 1; 2; 4; 8; 10; 20; 30; 40; 50; 60

Choices: On/Off; Suspend

Allows you to set the restore state from AC/Power

Loss

Loss.
Choices: Last State; Power Off; Power On

Allows you to enable / disable the Resume on PME
function.

Allows you to select S3/S4/S5 mode or disable the
Resume on Keyboard clock function.
Choices: Disabled; S4/S5

Wake Up Key

Resume on PS/2

Mouse

If Resume On KBC is not disabled, this item allows
you to select any key to wake up system.

Allows you to S4/S5 mode or disable the Resume
on PS/2 Mouse function.

63

KT400-C

Resume On RTC Alarm Allows you to enable / disable the Resume On RTC

Alarm function.

RTC Alarm Date / Hour

/ Minute

If resume On RTC Alarm is enabled, this field al­lows you to set the Alarm date Hour, Minute and
second.
Date Choices: Every Day; 01 ~ 31
Hour Choices: 00 ~ 23
Minute Choices: 00 ~ 59

64

Chapter 4 BIOS Setup

4-6.6 PNP / PCI Configurations

PNP/PCI Configuration allows you to modify the system’s power saving
functions.

Run the PNP/PCI Configurations as follows:

1. Choose “PNP/PCI Configurations” from the Main Menu and a screen
with a list of options will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

PNP/PCI Configurations Setup Help

Plug and Play Aware O/S No
Clear NVRAM No
PCI Latency Timer (PCI Clocks) 32
Primary Graphics Adapter PCI
PCI IDE BusMaster Enabled
PCI Slot1 IRQ Priority Auto
PCI Slot2 IRQ Priority Auto
PCI Slot3 IRQ Priority Auto
PCI Slot4 IRQ Priority Auto
PCI Slot5 IRQ Priority Auto

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

65

KT400-C

Plug and Play Aware

Clear NVRAM

PCI Latency Timer (PCI

Clocks)

Primary Graphics

Adapter

PCI IDE BusMaster Allows you to enable / disable the PCI IDE Bus

PCI Slot 1/2/3/4/5 IRQ

Priority

Allows BIOS to recognize the Plug and Play Aware

O/S

Operating System.
Choices: No (default); Yes

Allows BIOS to clear the NVRAM data.
Choices: No (default); Yes

Allows you to set the PCI Latency Time.
Choices: 32; 64; 96; 192; 128; 160; 192; 224; 248;

Allows you to select the primary Graphics Adapter.
Choices: PCI; AGP

Master function.

Allows you to specify the IRQ for the PCI slots.
Choices: Auto; 3; 4; 5; 7; 9; 10; 11

66

Chapter 4 BIOS Setup

4-6.7 Integrated Peripherals

Integrated Peripherals option allows you to get some information inside
your system when it is working.

Run the Integrated Peripherals as follows:

1. Choose “Integrated Peripherals” from the Main Menu and a list of
options will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

Integrated Peripherals Setup Help

Onboard FDC Auto
Onboard Serial Port 1 Auto
Onboard Serial Port 2 Auto
Serial Port 2 Mode Normal
Onboard Parallel Port Auto
Parallel Port Mode ECP
Parallel Port IRQ Auto
Parallel Port DMA Channel Auto
Onboard MIDI Port Disabled
MIDI Port IRQ 5
Onboard Game Port 200
Onboard IDE Both
Onboard AC’97 Audio Enabled

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

67

KT400-C

Onboard FDC Allows you to enable / disable the Onboard FDC.

Choices: Auto; Enabled; disabled

Onboard Serial Port 1

Onboard Serial Port 2 Allows you to set the Onboard Serial Port B.

Serial Port 2 Mode

Onboard Parallel Port Allows you to configure onboard Parallel port .

Parallel Port Mode If Parallel Port is not disabled, this item allows you

Parallel Port IRQ If Parallel Port Mode is set at EPP, this item allows

Parallel Port DMA

Channel

Onboard MIDI Port

Allows you to set the Onboard Serial Port A.
Choices; auto; Disabled; 3F8/COM1; 2F8/COM2;
3E8/COM3; 2E8/COM4;

Choices; auto; Disabled; 3F8/COM1; 2F8/COM2;
3E8/COM3; 2E8/COM4;

Allows you to set the Serial Port B Mode.
Choices: Normal; IrDA; ASKIR;

Choices: Auto; Disabled; 378; 278; 3BC;

to configure parallel port mode.
Choices: ECP; EPP + ECP; Normal; EPP

you to set the Parallel Port IRQ.
Choices: 5; 7

If Parallel Port Mode is set at ECP, this item allows
you to set the DMA Channel.
Choices: 0; 1; 3

Allows you to configure onboard MIDI port address.
The choices: Disabled; 300h; 310h; 320h; 330h

MIDI Port IRQ If the onboard MIDI port is enabled, this item shows

up to allow you to configure the MIDI Port IRQ to
IRQ 5.

Onboard Game Port Allows you to configure Onboard Game port

address.
The choices: Disabled; 200h; 208h

68

Chapter 4 BIOS Setup

Onboard IDE Allows you to choose the Onboard IDE Mode.

Choices: Disabled; Primary; Secondary; Both

Onboard AC‘97 Audio Allows you to disable or set AC’97 Audio automati-

cally by system.
Choices: Auto; Disabled

69

KT400-C

4-6.8 SmartDoc Anti-Burn Shield

This menu helps you to read only and get more information on the
working CPU temperature, FAN speed and voltage.

1. Choose “SmartDoc Anti-Burn Shield” from the Main Menu and a
screen with a list of current status of your working system will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

SmartDoc Anti-Burn Shield Setup Help

CPU Warning Temperature Disabled
CPU Shut Down Temperature Disabled
CPU Fan Low speed Warning Disabled
CPU Fan Low Speed Shutdown (Disabled)
(ABSII)CPU Current Temperature (53
(ABSII)CPU Shutdown Temperature 85
Temperature 1 (31 0C/87 0F)
Temperature 2 N/A
Fan 1 Speed (5443 RPM)
Fan 2 Speed (0 RPM)
Vcore (+1.680 V)
+2.5V (+2.504 V)
+3.3V (+3.408 V)
+5.0V (+5.126 V)
+12.0V (+11.187V)

-12.0V (-11.972V)
5V SB (+5.164V)
Battery (+3.296V)

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

0

C/1270F)

0

C/185 0F

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

CPU Warning Tem-

perature

Select a upper limits for the CPU temperature. If
the CPU temperature extends beyond the limit,
any warning mechanism programmed into your sys­tem will activate the warning.

70

Chapter 4 BIOS Setup

CPU Shutdown Tem-

perature

CPU Fan Low Speed

Warning

CPU Fan Low Speed

Shutdown

ABS II CPU Current

Temperature(for

Athlon XP/Duron

Morgan)

ABS II CPU Shutdown

Temperature(for

Athlon XP/Duron

Morgan)

Temperature 1 Shows current CPU internal temperature.
Temperature 2 Shows current CPU external temperature.

This feature allows you to set the shutdown tem­perature to the running CPU.
Choices: Disabled; 50 0C~710C in 3˚ C stepping

This feature allows you to set up the CPU Fan Low
Speed warning function.
Choices: Disabled; Stop/0RPM; 1000~6000RPM

This feature allows you to enable/disable the CPU
Fan Low Speed Shutdown function.
Choices: Disabled; Stop/0RPM; 1000~6000RPM

This item will appear if Athlon XP or Duron Morgan
CPU is running on board. This item is to show the
current temperature inside the running CPU.

This item will appear if Athlon XP or Duron Morgan
CPU is running on board. ABS II (Anti-burn Shield
II) allows user to set up the safeguard temperature
for the CPU designed with a protective thermal di­ode inside the CPU itself. Default Safeguard tem­perature is 85˚C, at which the XP or Duron Morgan
CPU will shutdown. Usually, a jumper is also de­signed on board for enabling/disabling ABS II
function.
Choices: 75˚C / 167˚F; 80˚C / 176˚F
85˚C / 185˚F(default); 90˚C / 194˚F
95˚C / 203˚F; 100˚C / 212˚F

Fan 1 / 2 Displays the current speed of CPU Fan, and other

CPU Vcore Shows CPU core actual voltage value.

+2.5V/+3.3V/+5.0V/

+12V/-12V/+5.V SB/

Battery Shows current voltage against battery power supply.

onboard device which user has connected to the
onboard Fan Connectors.

Shows current voltage against the respective power
supply.

71

KT400-C

4-6.9 Frequency/Voltage Control

Run the “Frequency/Voltage Control” as following:

1. Choose “Frequency/Voltage Control” from the Main Menu and a
screen with a list of options will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

Frequency/Voltage Control Setup Help

RedStorm Overclocking Tech (Optional)
CPU Linear Frequency Disabled
CPU Clock 100 MHz
Spread spectrum Disabled
Auto Detect PCI Slot Disabled

CPU Voltage Control Auto
AGP Voltage Control 1.5V
DIMM Voltage Control 2.5V

CPU Ratio Selection Default

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation
of the <F> keys follows:

<F1>: “Help” gives options available for each item.
<F9>: Setup BIOS default values.
<F10>: Save and Exit Setup.

3. Press <ESC> to return to the Main Menu when you finish setting up
all items. The following item descriptions are provided as a quick
guide to your setup.

72

Chapter 4 BIOS Setup

(Optional)

Redstorm Overclock-

CPU Linear

Frequency

CPU Clock If CPU Linear Frequency is set at Enabled, this item

Spread Spec-

Auto Detect PCI Slot Allows you to enable / disable the Auto Detect PCI

CPU Voltage

Control

If this option is chosen in BIOS, press <Enter> to
start RED STORM OVERCLOCKING TECH. This

ing

option helps user to raise CPU clock automatically

Tech

until an unacceptable valueis reached. Then BIOS
will restart your systemwith a highest accept­able CPU clock.

This item allows you to enable / disable this setting
function.

allows you to set CPU Clock.
Choices: 100MHz ~200MHz in 1MHz stepping.

Allows you to enable / disable this Spread

trum

Speectrum function. If enabled, this function will
reduce the EMI (Electromagnetic Interference) in
your system. If you do not have an EMI problem,
leave this item disabled.

Slot function.

allows you to configure the CPU Voltage. Usually,
to raise CPU voltage will raise the chance of CPU
overclocking and yet risk damage of CPU.
Choices: Auto; 1.100V ~1.850V in 0.025 stepping

AGP Voltage

Control

DIMM Voltage

Control

CPU Ratio

Selection

allows you to configure the AGP Voltage.
Choices: 1.5V; 1.6V; 1.7V; 1.8V

allows you to configure the DIMM Voltage.
Choices: 2.5V; 2.6V; 2.7V; 2.8V

If CPU onboard is one with an adjustable or un­locked CPU ratio, this item allows you user to ad­just the CPU Ratio. If your CPU is one with the
CPU Ratio locked, this item will be invalid.

73

KT400-C

4-6.10 System Information

This menu helps you to read only and get more information on the
system.

1. Choose “System Information” from the Main Menu and a screen with
a list of current status of your working system will appear:

AMIBIOS NEW SETUP UTILITY - VERSION 3.31a

System Information Setup Help

BIOS Version (12/03/02)
Processor Type (AMD Duron(tm)
Processor Speed (1300MHz)
Base Memory (640KB)
Extended Memory (255MB)
Total Memory (256MB)
Cache Size (192KB)
Memory Bank 0 (SDRAM)
Memory Bank 1 (SDRAM)
Memory Bank 2 (None)

F1: Help : Select Item +/- : Change Values F9: Setup Defaults
Esc: Previous Menu Enter: Select Sub-Menu F10: Save and Exit

2. Press <ESC> to return to the Main Menu. In case any irregular read­ing appears about your system, it indicates that a problem exists
therein. To solve the problem, a hardware engineer or your dealer is
recommended.

74

Chapter 4 BIOS Setup

4-6.11 Set Supervisor Password

This option allows you to set a Supervisor password for the system:

1. Choose “Set Supervisor Password” in the Main Menu and press
<Enter>. Then the following message appears:

[ Enter new supervisor password ]

2. The first time you run this option, enter your password up to 8 char­acters and press <Enter>. (The screen does not display the entered
characters.)

3. After you enter the password, the following message appears prompt­ing you to confirm the password:

[ Retype new supervisor Password ]

4. Enter the same password “exactly” the same as you have just typed
to confirm the password and press <Enter>.

5. The following message appears to confirm the new password setup.

[ New supervisor password installed ]

Any Key to Continue

6. Then press any key to continue your CMOS Setup. To save the pass­word setup, you should press “Save & Exit Setup” and choose “yes”
to exit and save setup.

7. After the Supervisor password is set, you have to choose whether
the password is for entering the system or only for entering BIOS
Setup program. To make the choice, please enter BIOS Setup and
choose “Advanced BIOS Features” in the main menu. (At entering
BIOS Setup, you have to enter the password now.) In “Advanced
BIOS Features”, choose “Password Check” and change the option.
The “Setup” option is to set the password only for entering BIOS
Setup. The “Always” option is to set the password for entering the
system.

75

KT400-C

8. To change or remove a current supervisor password, choose “Set
Supervisor Password” and press <Enter>. An instruction box appears
on the screen, prompting you to enter the current password first:

[ Enter current supervisor password ]

9. Type the current password with keyboard and then press <Enter>.
An instruction box appears, prompting you to enter new supervisor
password:

[ Enter new supervisor password ]

10. If you enter a new password into the box, you will be using this new
password after you have finished and saved this new setup. Instead,
if you press <Enter> before you enter any new password into the
instruction box, another message box appears, telling you that you
have disabled the Supervisor password. That means, no password
is set for either entering BIOS Setup or system:

[ Supervisor password disabled ]

Any Key to Continue

NOTE: If you forget or lose a supervisor password, the only
way to access the system is to clear the CMOS. All setup
informations will then be cleared including the password and
you need to run the BIOS setup program again so as to
reconfigure BIOS.

76

Chapter 4 BIOS Setup

4-6.12 Load Optimized Defaults

When you press <Enter> on this item, you will get a confirmation dialog
box with a message similar to:

[ Load Optimized Settings ]

Press [Enter] to continue

or [ESC] to abort

Press <Enter> now to load Optimal values for all the Setup options.

4-6.13 Save & Exit Setup

Save & Exit Setup allows you to save all modifications you have specified
into the CMOS memory. Highlight this option on the Main Menu and
press <Enter>. The following message appears:

[ Saving current settings and exit ]

Press [Enter] to continue

or [ESC] to abort

Press <Enter> key to save the configuration changes and exit CMOS
Setup to restart your system.

4-6.14 Exit Without Saving

Exit Without Saving option allows you to exit the Setup Utility without
saving the modifications that you have specified. Highlight this option
on the Main Menu and the following message appears:

[ Quit Without Saving Changes ]

Press [Enter] to continue

or [ESC] to abort

Follow the message and press <Enter> key to exit CMOS Setup and
restart system.

77