SOLTEK SL-65DVB User Manual

SL-65DVB/65DV2 V1.0

USER MANUAL

R

USER NOTICE

Product Model : SL-65DVB/65DV2
Manual Revision : V1.0
Release Date : November 2000

his Users Guide & Technical Reference is for assisting system
manufacturers and end-users in setting up and installing the
motherboard.

Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for print­ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, trans­lated into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identifi­cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec­tive companies.

Soltek computer inc. Provides this manual “As is “ without war­ranty of any kind, either express or implied, including but not limited
to the implied warranties or conditions of merchantability or fitness
for a particular purpose. In no event shall Soltek computer inc. Be
liable for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con­sequential damages of any kind, even if Soltek computer inc. Has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.

Copyright © 2000 Soltek Computer Inc. All Rights Reserved.

• Intel, Celeron, Pentium II, Pentium III are trademarks of Intel Corporation.

• Intel 82815 Graphic Memory Controller Hub(GMCH), 82801 I/O Controller Hub(ICH) are trade­marks of Intel Corporation.

• VIA Cyrix III is trademark of VIA Corporation.

• Norton AntiVirus, Norton Ghost are trademarks of Symantec Corporation.

T

SOLTEK AROUND THE WORLD

SOLTEK COMPUTER INC.

Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chin, Taipei-

Hsien, Taiwan, R.O.C.

Telephone : [phone]
Fax : [phone]
E-mail : [e-mail]
Web site : http://www.soltek.com.tw

SOLTEK KOREA INC.

Address : 1002, Chungjin Bldg. 53-5 Wonhyo-Ro, 3-Ka,

Yongsan-Ku Seoul 140-113, Korea

Telephone : [phone]
Fax : [phone]
E-mail : [e-mail]

MOKA HOLDING B.V.

Address : De Run 4428 5503 LR Veldhoven, the Netherlands
Telephone : [phone]
Fax : [phone]
E-mail : [e-mail]

SOUL TECHNOLOGY EUROPE B.V.

Address : Sydneystraat 52-54 3047 BP Rotterdam, the Nether-

lands

Telephone : [phone]
Fax : [phone]
E-mail : [e-mail]
Web site : http://www.soultech-europe.com

4

65DVB/65DV2

C O N T E N T

CHAPTER 1

INTRODUCTION ........................................................................... 6

1-1 ITEM LIST CHECKUP ............................................................................ 6

1-2 CPU ........................................................................................................ 6

1-3 CHIPSET ................................................................................................ 6

1-4 ADVANCED HIGH-PERFORMANCE DRAM CONTROLLER................ 6

1-5 FULL FEATURED ACCELERATED GRAPHICS PORT (AGP)

CONTROLLER ....................................................................................... 7

1-6 MULTI-I/O FUNCTION ........................................................................... 7

1-7 EXTENSION SLOTS .............................................................................. 7

1-8 BIOS ....................................................................................................... 8

1-9 SOUND CONTROLLER ......................................................................... 8

1-10 POWER MANAGEMENT ..................................................................... 8

1-11 FROM FACTOR .................................................................................... 8

1-12 HARDWARE MONITORING ................................................................ 8

1-13.1 MOTHERBOARD LAYOUT --- 65DVB .............................................. 9

1-13.2 MOTHERBOARD LAYOUT --- 65DV2 ............................................ 10

1-14 CHIPSET SYSTEM BLOCK DIAGRAM ............................................. 11

1-15 MOTHERBOARD SPECIFICATION TABLE OF ................................. 12

65DVB & 65DV2 ................................................................................. 12

CHAPTER 2

HARDWARE SETUP ................................................................... 14

2-1 CPU INSTALLATION ............................................................................ 14

2-2 MEMORY INSTALLATION ................................................................... 16

2-3 HDD / FDD INSTALLATION ................................................................. 17

2-4 BUS RATIO SELECT ........................................................................... 18

2-4.1 BUS CLOCK SELECT ....................................................................... 18

2-5 JUMPER DEFINITION ......................................................................... 19

2-5.1 ONBOARD FAN CONNECTOR (FAN1/FAN2) .................................. 19

2-5.2 USB PORT SELECT-1 (JP3/JP4) ..................................................... 19

2-5.3 ONBOARD AC97 CODEC SELECT (JP5/JP9) ................................. 20

2-5.4 USB PORT SELECT-2 (JP6/JP7) ..................................................... 20

2-5.5 POWER LOST RESUME (JP8)......................................................... 21

2-5.6 CD-ROM AUDIO CONNECTOR (CD_IN1/CD_IN2) ......................... 21

2-5.7 CLEAR CMOS DATA (JBAT1) .......................................................... 21

5

65DVB/65DV2

2-5.8 WAKE ON LAN FUNCTION (WOL1) ................................................ 21

2-5.9 THERMAL SENSOR CONNECTOR (RT2) ....................................... 23

2-6 CONNECTORS .................................................................................... 23

2-6.1 J2J3 ................................................................................................... 23

2-6.2 CHASSIS PANEL CONNECTOR ...................................................... 26

2-6.3 ATX POWER SUPPLY CONNECTOR .............................................. 26

2-6.4 AUDIO MODEM RISER SLOT (AMR) ............................................... 27

2-6.5 PS/2 MOUSE AND PS/2 KEYBOARD .............................................. 28

2-6.6 IRQ DESCRIPTION .......................................................................... 28

CHAPTER 3

SOFTWARE SETUP .................................................................... 30

3-1 ABOUT SOLTEK SUPPORT CD .......................................................... 30

3-2 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)................... 30

3-3 AC’97 AUDIO CODEC INSTALLATION ................................................ 34

3-4 HARDWARE MONITOR INSTALLATION ............................................. 35

CHAPTER 4

BIOS SETUP ............................................................................... 36

4-1 INTRODUCE THE BIOS ...................................................................... 36

4-2 WHAT IS BIOS SETUP ........................................................................ 36

4-3 HOW TO RUN BIOS SETUP ............................................................... 36

4-4 WHAT IS CMOS ................................................................................... 37

4-5 WHAT IS POST .................................................................................... 37

4-6 BIOS UPGRADE .................................................................................. 37

4-6.1 BEFORE UPGRADE BIOS ............................................................... 37

4-6.2 UPGRADE PROCESS ...................................................................... 38

4-7 CMOS SETUP UTILITY ....................................................................... 41

4-8 STANDARD CMOS SETUP ................................................................. 42

4-9 ADVANCED BIOS FEATURES ............................................................ 45

4-10 ADVANCED CHIPSET FEATURES ................................................... 50

4-11 INTEGRATED PERIPHERALS ........................................................... 55

4-12 POWER MANAGEMENT SETUP ...................................................... 59

4-13 PNP / PCI CONFIGURATION ............................................................ 65

4-14 PC HEALTH STATUS ......................................................................... 68

4-15 FREQUENCY/VOLTAGE CONTROL ................................................. 69

4-16 LOAD OPTIMIZED DEFAULTS .......................................................... 71

4-17 SET SUPERVISOR / USER PASSWORD ......................................... 71

4-18 SAVE & EXIT SETUP ......................................................................... 72

4-19 EXIT WITHOUT SAVING ................................................................... 72

6

65DVB/65DV2

CHAPTER 1

INTRODUCTION

1-1 ITEM LIST CHECKUP

• Motherboard

• Support CD

• User’s Manual

• Bundle Bonus Pack CD

• Bundle Bonus Pack Manual

• Temperature Sensor Cable

• ATA 66/100 IDE Cable

• FDD Cable

1-2 CPU

• Supports Intel® FC-PGA Pentium !!!TM up to 1GHz or above.

• Supports Intel

®

FC-PGA 370 Celeron & PGA 370 Celeron up to 766MHz

or above.

• Supports VIA Cyrix !!! up to 600MHz.

• Supports CPU voltage Auto-Detect circuit.

1-3 CHIPSET

• North Bridge - VIA VT82C693A APOLLO PRO-PLUS.

• South Bridge - VIA VT82C686A (for 65DVB only)
VIA VT82C686B (for 65DV2 only)

1-4 ADVANCED HIGH-PERFORMANCE DRAM
CONTROLLER

• Supports FP, SDRAM, VCM memory types up to 3 DIMMS.

• 64-bit data width and 3.3V DRAM interface.

• Supports up to 768MB memory space.

• Different DRAM types may be used in mixed combinations.

• PCI-2.2 compliant, 32 bit 3.3V PCI interface with 5V tolerant inputs .

• DRAM interface synchronous with host CPU (66/100/133 MHz) or AGP
(66MHz) for most flexible configuration.

• DRAM interface may be faster than CPU by 33MHz to allow use of PC100

7

65DVB/65DV2

memory modules with 66MHz Celeron or use of PC133 with 100MHz
Pentium III.

• DRAM interface may be slower than CPU by 33 MHz to allow use of older
memory modules with newer CPUs (e.g., PC66 memory modules with
100 MHz Pentium III).

1-5 FULL FEATURED ACCELERATED GRAPHICS PORT
(AGP) CONTROLLER

• AGP v2.0 compliant

• Supports Sideband Addressing (SBA) mode (non-multiplexed address/
data)

• Supports 133MHz 2x mode for AD and SBA signaling

• Pipelined split-transaction long-burst transfers up to 533 MB/sec

1-6 MULTI-I/O FUNCTION

• Two Ultra DMA-33 / 66 Master Mode PCI EIDE ports (for 65DVB only).

• Two Ultra DMA-33 / 66 / 100 Master Mode PCI EIDE ports (for 65DV2
only).

• Two UART’s for Complete Serial Ports.

• One dedicated IR connector:

Third serial port dedicated to IR function either through the two complete serial
ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK (Amplitude Shift
Keyed) IR.

• Multi-mode parallel connector:
Standard mode, ECP and EPP support.

• Floppy Disk connector:
Two FDDs with drive swap support .

• Universal Serial Bus connector:

--- USB v1.1 and Intel Universal HCI v1.1 compatible.

--- Provides 2 build-in USB ports (another 2 internal USB ports for extensible
purpose require an optional USB connect cable).

• PS/2 Keyboard connector.

• PS/2 Mouse connector.

1-7 EXTENSION SLOTS

• Five PCI bus Mater slots.

• One ISA slot.

• One AMR slot.

8

65DVB/65DV2

• One AGP 4x mode slot.

• Three DIMM slots.

1-8 BIOS

• Award BIOS Version 6.0.

• Supports Plug & Play V1.0.

• FLASH MEMORY for easy upgrade.

• Supports BIOS writing protection.

• Year 2000 compliant.

1-9 SOUND CONTROLLER

• Sound Blaster Pro Hardware and Direct Sound Ready AC’97 Digital
Audio Controller with Codec onboard.

1-10 POWER MANAGEMENT

• ACPI 1.0 compliant (Advanced Configuration and Power Interface).

• APM V1.2 compliant (Legacy power management).

• System event monitoring with two event classes.

• Supports PS/2 Keyboard & Mouse power on.

• Supports Wake On LAN (WOL) & Wake On Modem.

• Supports real time clock (RTC) with date alarm, month alarm, and century

field.

1-11 FROM FACTOR

• ATX from factor, 4 layers PCB.

• Motherboard size 19.0cm X 30.5cm.

1-12 HARDWARE MONITORING

• Programmable control, status, monitor and alarm for flexible desktop

management (software included).

• Five-positive voltage.

• Two-temperature monitoring.

• Three Fan-speed monitoring.

9

65DVB/65DV2

1-13.1 MOTHERBOARD LAYOUT --- 65DVB

• Default Setting: Intel Celeron 300A/66 MHz

Using non-compliant memory with higher bus clock (over clocking) may severely
compromise the integrity of system.

1 3
1 3

JP6
JP7

1 3

JP9

1 3

JP8

1 3
1 3

1 3

1 4

1 4

JP3
JP4

JP5

1

3

JP11

1 3

JBAT1

SPK RST PWR/LED SUSLED

HD/LED IR PWR SUSPEND

FAN2

FAN1

J2 J3

1 1

LPT1

COM2 COM1

GAME/MIDI PORT

LINE

OUT

LINE

IN

MIC

JWOL1

SW1

CD_IN2
CD_IN1

AMR

ISA

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

DIMM1

DIMM2

DIMM3

FDC1

IDE2

IDE1

SOCKET 370

RT2

RT1

ATX POWER

FLASH BIOS

Li

Battery

ON DIP

1 2 3 4 5 6

USB2

1

16

AC'97
Codec

Clock
Generator

PS/2

MOUSE

PS/2

K/B

upper

lower

USB1

USB0

upper

lower

VIA

VT82C

693A

VIA

VT82C

686A

AGP 2X

10

65DVB/65DV2

1-13.2 MOTHERBOARD LAYOUT --- 65DV2

• Default Setting: Intel Celeron 300A/66 MHz

1 3
1 3

JP6
JP7

1 3

JP9

1 3

JP8

1 3
1 3

1 3

1 4

1 4

JP3
JP4

JP5

1

3

JP11

1 3

JBAT1

SPK RST PWR/LED SUSLED

HD/LED IR PWR SUSPEND

FAN2

FAN1

J2 J3

1 1

LPT1

COM2 COM1

GAME/MIDI PORT

LINE

OUT

LINE

IN

MIC

JWOL1

SW1

CD_IN2
CD_IN1

AMR

ISA

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

DIMM1

DIMM2

DIMM3

FDC1

IDE2

IDE1

SOCKET 370

RT2

RT1

ATX POWER

FLASH BIOS

Li

Battery

ON DIP

1 2 3 4 5 6

USB2

1

16

AC'97
Codec

Clock
Generator

PS/2

MOUSE

PS/2

K/B

upper

lower

USB1

USB0

upper

lower

VIA

VT82C

693A

VIA

VT82C

686B

AGP 2X

Using non-compliant memory with higher bus clock (over clocking) may severely
compromise the integrity of system.

11

65DVB/65DV2

1-14 CHIPSET SYSTEM BLOCK DIAGRAM

VIA

VT82C

693A

VIA

VT82C

686A/

686B

ISA1

PCI3

PCI2

PCI1

PCI5

PCI4

Keyboard
& Mouse

Main
Memory
(DRAM)

AGP Slot or

3D Graphics

Controller

PM Control ,
GPIO , Reset

BIOS
ROM

USBx4

Super IO

IDE x 2

Serial Port x 2

Infrared Port x 1

Parallel Port x 1

FDD x1

Socket 370

CPU

Figure 1-11. VIA VT693A System Block Diagram Using the
VT82C686A or VT82C686B South Bridge

Hardware
Monitoring

AC97 Codec

ATA 33/66 or

ATA 33/66/100

12

65DVB/65DV2

1-15 MOTHERBOARD SPECIFICATION TABLE OF
65DVB & 65DV2

Model

VIA686A VIA686B

65DVB

North bridge

VIA VT82C693A APOLLO PRO-PLUS

Sorth bridge

AGP Interface AGP Pro 2X Mode

Build-in AC97 codec

Memory

Supports PC133 and PC100 FP, SDRAM and Virtual Channel

Memory (VCM) up to 768MB

3 DIMM Slots

Audio

IDE

2 x Ultra 33/66

IDE ports

2 x Ultra33/66/100

IDE ports

I/O

yes

yes

4 x USB ports, 1 x FDD port, 2 x COM ports,

1 x LPT port, 1 x IrDA, PS/2 Mouse, PS/1 K/B

PCI slot

5 x PCI Master Slots

ISA slot

1 x ISA slot

Hardware

Monitoring

BIOS writing

Protection

Remark

65DV2

13

65DVB/65DV2

ATTENTION !!!

1. Please refer to your processor installation or other
documentation attached with your CPU for detailed
installing instruction.

2. Installing a heat sink and cooling fan is necessary for
proper heat dissipation from your CPU. Uncorrected
installation may result in overheating and damage of
your CPU.

3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD make sure of correct specifi­cation both of CPU CLOCK and RATIO. Uncorrected
setting may cause damage to your CPU.

14

65DVB/65DV2

CHAPTER 2

HARDWARE SETUP

2-1 CPU INSTALLATION

Warning!!!

Never run the processor without the heat sink properly and firmly attached
PERMANENT DAMAGE WILL RESULT.

1. Pull the lever sidways away from the socket, and then raise the lever up
to a 90-degree angle.

2. Take note of the red circle as below picture. When insert the CPU into
socket, you can find out there is a definite pin orientation for CPU and
socket.

SOCKET 370

SOCKET 370

15

65DVB/65DV2

3. Make sure that the CPU positions in the socket tightly, and then put the
lever down to complete the CPU installation.

SOCKET 370

16

65DVB/65DV2

WARING !!!

• Make sure that you unplug your power supply when adding or remoning
memory modules or other system components, failure to do so may cause

severe damage to both your motherboard and expansion cards.

• Be careful when inserting or removing DIMM, fouceing a DIMM in or out of
a socket can be damaged the memory module or the socket. Some of DIMMs
contain EDO or FPM DRAM that accept only 5V power. These DIMM types
are incompliant with the motherboard, the M/B only supports 3.3V true
SDRAM DIMMs

2-2 MEMORY INSTALLATION

168-Pin DIMM Notch Key Definitions(3.3V)

DRAM Key Position Voltage Key Position

Unbuffered

3.3V

Installing DIMM:

• Make sure you have the correct memory module type for your motherboard.

• Insert the mdule(s) as shown, DIMMs have 168-pins and two notches that
will match with the onboard DIMM socket, memory modules are installed by
inserting them straight into the slot until they “click” into place. They only fit
in one direction so do not force them into place.

Removing:

• Press the holding clips on both sides of socket out ward to release the
DIMM, Gintly pull the DIMM out of the socket.

17

65DVB/65DV2

1 3
1 3

JP6
JP7

1 3

JP9

1 3

JP8

1 3
1 3

1 3

1 4

1 4

JP3
JP4

JP5

1

3

JP11

1 3

JBAT1

SPK RST PWR/LED SUSLED

HD/LED IR PWR SUSPEND

FAN2

FAN1

J2 J3

1 1

LPT1

COM2 COM1

GAME/MIDI PORT

LINE

OUT

LINE

IN

MIC

JWOL1

SW1

CD_IN2
CD_IN1

AMR

ISA

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

DIMM1

DIMM2

DIMM3

FDC1

IDE2

IDE1

SOCKET 370

RT2

RT1

ATX POWER

FLASH BIOS

Li

Battery

ON DIP

1 2 3 4 5 6

USB2

1

16

AC'97

Codec

Clock
Generator

PS/2

MOUSE

PS/2

K/B

upper

lower

USB1

USB0

upper

lower

VIA

VT82C

693A

VIA

VT82C

686B

AGP 2X

2-3 HDD / FDD INSTALLATION

• To install HDD (Hard Disk Drive), you may connect the cable’s blue
connector to the motherboard’s primary (IDE1) or secondary IDE
connector, and then connect the gray connector to your slave de­vice and the black connector to your master device.If you install two
hard disks , you must configure the second drive to Slave mode by
setting its jumper accordingly.Please refer to your hard disk docu­mentation for the jumper settings.

• To install FDD (Floppy Disk Drive), you may connect the single end
to the board , and connect two plugs on the other end to the floopy
drives.

Floppy Disk Drive Connector:
Orient the red markings on
the floppy ribbon cable to
Pin1.

Hard Disk Drive Connector:
Orient the red markings on
the IDE ribbon cable to Pin1.

18

65DVB/65DV2

2-4 BUS RATIO SELECT

2-4.1 BUS CLOCK SELECT

• Normally, the Bus Ratio (Frenquency Multiple) of your processor is locked
by processor’s Vendor,setting of the CPU Bus Ratio will have no effect.

• Bus Ratio exceed 8.0X, user can not change all values from the ratio will
be detected by BIOS automatically.

• The Bus Ratio Setting is available on unlocked processors only.

• Over clocking is not recommanded, your system may work unstable.

SW1 DIP1 ~ DIP4 SETTING

OFF

ON

ON

ON

ON

1 2 3 4 5 6

OFF

ON

3.0x

OFF

OFF

ON

ON

ON

1 2 3 4 5 6

OFF

ON

3.5x

OFF

ON

ON

ON

ON

1 2 3 4 5 6

OFF

ON

4.0x

OFF

OFF

ON

ON

ON

1 2 3 4 5 6

OFF

ON

4.5x

OFF

OFF

ON

ON

ON

1 2 3 4 5 6

OFF

ON

5.0x

OFF

OFF

OFF

ON

ON

1 2 3 4 5 6

OFF

ON

5.5x

OFF

ONONON

ON

1 2 3 4 5 6

OFF

ON

6.0x

OFF

OFF

ON

ON

ON

1 2 3 4 5 6

OFF

ON

6.5x

OFF

OFF

ON

ON

ON

1 2 3 4 5 6

OFF

ON

7.0x

OFF

OFF

OFF

ON

ON

1 2 3 4 5 6

OFF

ON

7.5x

OFF

OFF

ON

ON

ON

1 2 3 4 5 6

OFF

ON

8.0x

ON OFF1ON OFF2ON OFF3ON OFF

4

OFF

5ON6

66/100/133MHz

Auto Select

(default)

1

3

ON OFF1ON OFF2ON OFF3ON OFF

4

OFF5OFF

6

100MHz

1

3

ON OFF1ON OFF2ON OFF3ON OFF

4

OFF

5ON6

133MHz

1

3

ON

ON

ON

SW1 DIP5 ~ DIP6 JP11: FSB SELECT

19

65DVB/65DV2

2-5 JUMPER DEFINITION

• The figure below shows the location of the motherboard’s jumper blocks.

CAUTION

• Do not move the jumper with the power on. Always turn off the power and unplug
the power cord from the computer before changing the jumper. Otherwise, the
motherboard could be damaged.

Those connectors support processor/system cooling fan with +12V. Those support
three pin head connector. When connecting the wire to FAN connectors, user should
give attention that the red wire is the positive and should be connected to the
+12V, the black wire is Ground and should be connected to GND. If your
motherboard has Hardware Monitor chipset on-board, you must use a specially
designed fan with speed sensor to take advantage of this function.
For fans with fan speed sensor, every rotation of the fan will send out 2 pulses.
System Hardware Monitor will count and report the fan rotation speed.

NOTE 1: Always consult vendor for proper CPU cooling fan.
NOTE 2: CPU FAN supports the FAN control. You can install PC Alert utility.

This will automatically control the CPU FAN speed according to the
actual CPU temperature.

GND
+12V
SENSOR

CPU FAN

FAN1 / FAN2: ONBOARD FAN CONNECTOR (12V)

FAN2

FAN1

SYSTEM FAN

2-5.1 ONBOARD FAN CONNECTOR (FAN1/FAN2)

2-5.2 USB PORT SELECT-1 (JP3/JP4)

Redirect USB port 3 to USB 2
connector (default)

JP3/JP4: USB PORT SELECT (1)

1 3

1 3

JP3
JP4

1 3

1 3

JP3
JP4

Redirect USB port 3 to AMR

20

65DVB/65DV2

Redirect USB port 2 to USB 2
connector (default)

JP6/JP7: USB PORT SELECT (2)

1 3

1 3

JP6
JP7

1 3

1 3

JP6
JP7

Redirect USB port 2 to AGP

NOTE: This jumper allows user to use the switch of ATX power supply

to control ON/OFF switch directly instead of using the power
switch on the motherboard.

Normal (default)

JP8: POWER LOST RESUME

3

1

3

1

JP8

Enabled

JP8

2-5.5 POWER LOST RESUME (JP8)

CD_IN1PIN NO.

CD_IN1/CD_IN2: CD-ROM AUDIO CONNECTOR

CD_IN2

PIN 1 Left Channel

GND

PIN 2

GND

GNDPIN 3

Right ChannelPIN 4

GND

Left Channel

Right Channel

2-5.6 CD-ROM AUDIO CONNECTOR (CD_IN1/CD_IN2)

2-5.3 ONBOARD AC97 CODEC SELECT (JP5/JP9)

2-5.4 USB PORT SELECT-2 (JP6/JP7)

Disabled

JP5/JP9: ONBOARD AC'97 CODEC SELECT

3

1

3

1

1 3

JP5 JP9

1 3

JP5 JP9

Enabled (default)

21

65DVB/65DV2

Clear CMOS Data

Retain Data (default)

JBAT1: CLEAR CMOS DATA

JBAT1

1 3

JBAT1

1 3

A battery must be used to retain the motherboard configuration in
CMOS RAM.

NOTE : You can clear CMOS by shorting 2-3 pin when the system is

POWER OFF. Then, return to 1-2 pin position (default). It may
damage the motherboard if clearing the CMOS in POWER ON
status. Unplug the power cord from power supply before
clearing CMOS will be a best bet for user.

2-5.7 CLEAR CMOS DATA (JBAT1)

Connect the Wake On LAN signal from LAN card
to WOL1

WOL1 : WAKE ON LAN (WOL) FUNCTION

WOL1

GND

+5V standby

PME

This connector connects to a LAN card with a Wake On LAN output. The
connector powers up the system when a wake-up packet or signal is received
through the LAN card.

This feature requires that Wake On LAN feature is enabled at the BIOS
“Power Management Setup” and that your system has an ATX power supply with
at least 720mA / +5V standby power.

2-5.8 WAKE ON LAN FUNCTION (WOL1)

22

65DVB/65DV2

a: Connect to RT2.
b: Connect this thermal sensor
to particular device which
generates lots of heat such
as Hard Driver, VGA chip, etc.
When connected, user could
observe the temperature
change from the BIOS
program.

RT2: THERMAL SENSOR CONNECTOR

2-5.9 THERMAL SENSOR CONNECTOR (RT2)

USB2: 2nd USB Port

GAME/MIDI PORT

MIC port: Microphone Jack

Line In port: Audio In Jack

Line Out / Speaker Out port: Audio Out Jack

23

65DVB/65DV2

2-6 CONNECTORS

• In this section we list all external connectors that user will use them.

2-6.1 J2J3

123456789101112131415

J2

PIN 1 +5V

HDD LED CONNECTOR

PIN 2 HDD LED SIGNAL
PIN 3 HDD LED SIGNAL
PIN 4 +5V

DESCRIPTION

This connector supplies power to the cabinet's IDE
activity LED. Read and write activity by devices
connected to the Primary or SecondaryIDE
connector will cause the LED to light up.

123456789101112131415

J2

INFRARED CONNECTOR

PIN 6 INFRARED TRANSMIT SIGNAL
PIN 7 GND
PIN 8 INFRARED RECEIVE SIGNAL
PIN 9 NONE
PIN 10 +5V

DESCRIPTION

This connector supports an optional wireless
transmitting and receiving infrared module. This
module mounts to a small opening on system cases
that support this feature.
User must also configure the setting through
BIOS program "Peripheral Setup" to select whether
UART2 is directed for use with COM2 or IrDA.
Use the five pins and connect a ribbon cable from
the module to the motherboard's IR connector
according to the pin definitions.

24

65DVB/65DV2

ATX POWER SWITCH

PIN 12 ATX POWER SWITCH
PIN 13 GND

DESCRIPTION

The system power is controlled by a momentary
switch connected to this lead.
Pressing the button once will switch the system
between ON and SOFT OFF.
Pushing the switch while in the ON mode for more
4 seconds will turn the system off.
The system power LED shows the status of the
system's power.

123456789101112131415

J2

SMI CONNECTOR

PIN 14 SMI(System Managment Interrupt) SIGNAL
PIN 15 GND

DESCRIPTION

This allows user to manually place the system into a
suspend mode or "Green" mode, where system
activity is decreased to save electricity and prolong
the life of certain components when the system is
not in use. This 2-oin connector connects to the
case-mounted suspend switch. If you do not have a
switch for the connector, you may use the "Turbo
Switch".
SMI is activated when it detects a short to open
moment and therefore leaving it shorted will not
cause any problems. This may require one or two
presses depending on the position of the switch.
Wake-Up can be controlled by settings in the BIOS
but the keyboard will always allow wake-up(the SMI
lead cannot wake up the system).

123456789101112131415

J2

25

65DVB/65DV2

123456789101112131415

J3

PIN 1 SPEAKER SIGNAL

SPEAKER CONNECTOR

PIN 2 NONE
PIN 3 GND
PIN 4 +5V

DESCRIPTION

This SPEAKER connector connects to the case­mounted speaker. Two sources (LINE OUT and
SPEAKER) allow you to hear system beeps and
warnings. Only SPEAKER allows you to hear system
beeps before the integrated audio has been properly
initialized.

123456789101112131415

J3

PIN 5 RESET SIGNAL

RESET SWITCH CONNECTOR

PIN 6 GND

DESCRIPTION

RESET SWITCH connector connects to the case­mounted reset switch for rebooting your system
without having to turn off your power switch. This is
a preferred method of reboot to prolong the life of
the system's power supply.

123456789101112131415

J3

PIN 14 SUSPEND LED SIGNAL

SUSPEND LED

PIN 15 GND

DESCRIPTION Connect to Suspend indicator light.

26

65DVB/65DV2

2-6.2 CHASSIS PANEL CONNECTOR

A : PS/2 MOUSE PORT
B : USB 0 PORT
C : LPT1 PORT
D : GAME/MIDI PORT
E : PS/2 KEYBOARD PORT
F : USB 1 PORT
G : COM1 PORT
H : COM2 PORT
I : LINE / SPEAKER OUT
J : LINE IN
K : MICROPHONE

A.

E. F. G. H. I. J. K.

B. C. D.

2-6.3 ATX POWER SUPPLY CONNECTOR

• This connector connects to an ATX power supply. The plug from the power
supply only inserts in an orientation because of the different hole sizes.
Find the proper orientation and push down firmly making sure that all pins
are aligned.

• Reminding that your power supply should support at least 10mA on the
5V standby voltage. It may cause an difficulty to power on the system if
the power supply cant support the load.

• For Wake On LAN function, the power supply should support at least
720mA current.

VCC
VCC

-5V
GND
GND
GND
Power Supply on
GND

-12V
VCC3

+12V

+5V Standby

Power Good

GND

VCC

GND

VCC

GND
VCC3
VCC3

27

65DVB/65DV2

2-6.4 AUDIO MODEM RISER SLOT (AMR)

The slot is a new open industry-standard specification for Audio/Modem
solution, which use the AC’97 interface as the connection between the riser
and the motherboard. Then specification main objective is to reduce the
baseline implementation cost of audio and modem. The motherboard uses
the primary channel for the on-board AC’97 code, so for using AMR
modem card on the motherboard, the AMR modem card must be
secondary.

Note: AMR modem card is not include with the motherboard.

1 3
1 3

JP6
JP7

1 3

JP9

1 3

JP8

1 3
1 3

1 3

1 4

1 4

JP3
JP4

JP5

1

3

JP11

1 3

JBAT1

SPK RST PWR/LED SUSLED

HD/LED IR PWR SUSPEND

FAN2

FAN1

J2 J3

1 1

LPT1

COM2 COM1

GAME/MIDI PORT

LINE

OUT

LINE

IN

MIC

JWOL1

SW1

CD_IN2
CD_IN1

AMR

ISA

PCI 1

PCI 2

PCI 3

PCI 4

PCI 5

DIMM1

DIMM2

DIMM3

FDC1

IDE2

IDE1

SOCKET 370

RT2

RT1

ATX POWER

FLASH BIOS

Li

Battery

ON DIP

1 2 3 4 5 6

USB2

1

16

AC'97
Codec

Clock
Generator

PS/2

MOUSE

PS/2

K/B

upper

lower

USB1

USB0

upper

lower

VIA

VT82C

693A

VIA

VT82C

686B

AGP 2X

AMR modem card

28

65DVB/65DV2

2-6.6 IRQ DESCRIPTION

• Both ISA and PCI expansion cards may require IRQs. System IRQs are
available to cards installed in the ISA expansion bus first, then any re­maining IRQs are available to PCI cards. Currently, there are two types of
ISA cards.

• The original ISA expansion card design, now referred to as “Legacy” ISA

2-6.5 PS/2 MOUSE AND PS/2 KEYBOARD

PIN 6 : None
PIN 5 : Mouse Clock
PIN 4 : Vcc
PIN 3 : GND
PIN 2 : None
PIN 1 : Mouse Data

PS/2 MOUSE

PIN 6 : None
PIN 5 : Keyboard Clock
PIN 4 : Vcc
PIN 3 : GND
PIN 2 : None
PIN 1 : Keyboard Data

PS/2 KEYBOARD

IRQ 0 System Timer 1

IRQ Function Description Priority

IRQ 1 Keyboard Controller 2
IRQ 2 Programmable Interrupt N/A
IRQ 3 Serial Port (COM 2) 11
IRQ 4 Serial Port (COM 1) 12
IRQ 5 13
IRQ 6 Floppy Disk Controller 14
IRQ 7 Parallel Port (LPT1) 15
IRQ 8 Real Time Clock (RTC) 3
IRQ 9 4
IRQ 10 5
IRQ 11 6
IRQ 12 PS/2 Mouse Port 7
IRQ 13 Coprocessor 8
IRQ 14 Primary IDE Channel 9
IRQ 15 Secondary IDE Channel 10

29

65DVB/65DV2

card, requires that you configurate the card’s jumpers manually and then

install it in any available slot on the ISA bus. To see a map of your used
and free IRQs in Windows 98, the Control Panel in My Computer, contains
a System icon, which gives you a Device Manager tab. Double-Clicking on
a specific hardware device gives you a Resources tab which shows the
Interrupt number and address. Double-Clicking Computers to see all the
interrupts and addresses for your system. Make sure that no two devices
use the same IRQ or your computer will experience problems when those
two devices are in use at the same time.

30

65DVB/65DV2

CHAPTER 3

SOFTWARE SETUP

3-1 ABOUT SOLTEK SUPPORT CD

• In Soltek support CD, it contains most informations for user’s requirement,
such as Acrobat Reader, BIOS, User’s Manual, Driver, Hardware Monitor
(if motherboard supports this function), Patch, and Utility etc.,User can
browse the CD and get further details in regard of our motherboard. Of
course, welcome to vendor’s website for the newest release.

3-2 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)

Step 1:

• Please put the Support CD attached to motherboard into the CD-ROM drive.

• When appears a welcome window as left screen, then user should choose “Install Driver”.

Step 2:

• Click on the “VIA Chipsets Driver”.

Step 4:

• Click on the “Install VIA 4-in-1 driver” to continue.

Step 3:

• Click on the “4-in-1 driver”.

Step 5:

• Press Next button to continue.

31

65DVB/65DV2

Step 6:

• Click “Yes” to continue.

Step 8:

• Click “Install” and Press Next button to continue.

Step 7:

• Press select the checkbox as below:
Bus Master PCI IDE Driver
AGP VxD Driver
VIA Chipset Function’s Registry
IRQ Routing Miniport Driver

Note: For user who are upgrading VIA Drivers. We

recommend installing the 4-in-1 as it will
automatically detect and update the necessary
drivers.

32

65DVB/65DV2

Step 10:

• The default setup destination is C:\VIADMATOOL,

press Next button to continue.

Step 9:

• We recommend user to leave “Enable / Disable

[Ultra] DMA” checkbox empty.

Note: Whether select this item or not, user needs to

enable the Hard Disk DMA function in Control
Panel manually. (For further details, please
refer to next page)

Step 11:

• Press Next button to continue.

33

65DVB/65DV2

Step 13:

• After all the setup process is finished, please restart

your computer by clicking on Finish.

A

bout Hard Disk DMA Function

Last but not least, user must enable the Hard Disk DMA function. The process is below:

1. [Start] [Setting] [Control Panel] [System] [Device Manager].

2. In Device Manager, select [Disk Drivers] [GENERIC IDE TYPEXX].

3. Select [Properties] for GENERIC IDE TYPEXX.

4. In Properties, select [Settings].

5. In Option item, select the DMA checkbox.

6. Restart your computer.

Step 12:

• Select “Install VIA AGP VxD” in turbo mode and

press Next button to continue.

34

65DVB/65DV2

3-3 AC’97 AUDIO CODEC INSTALLATION

Step 6:

• It’s recommended for user to restart the computer

after the audio driver is finished. Please select “Yes,
I want to restart my computer now”.

Step 5:

• When asking you install or remove the audio driver,

please select “Install” and press Next button to
continue.

Step 4:

• Press Next button to continue.

Step 3:

• Click on the “AC’97 driver”.

Step 2:

• Click on the “VIA Chipsets Driver”.

Step 1:

• Please put the Support CD attached to motherboard into the CD-ROM drive.

• When appears a welcome window as left screen, then user should choose “Install Driver”.

35

65DVB/65DV2

3-4 HARDWARE MONITOR INSTALLATION

Step 1:

• Please put the Support CD attached to motherboard into the CD-ROM drive.

• When appears a welcome window as left screen, then user should choose “Install Driver”.

Step 2:

• Click on the “VIA Chipsets Driver”.

Step 3:

• Click on the “Hardware Monitor Utility”.

Step 6:

• Press Next button to finish the Hardware Monitor
setup process.

Step 5:

• The default destination is C:\VIAhm, then press
Next button to continue.

Step 4:

• Press Next button to continue.

65DVB/65DV2

36

4-1 INTRODUCE THE BIOS

• BIOS stands for Basic Input Output System. It is sometimes called ROM
BIOS because it is stored in a Read-Only Memory(ROM) chip on the
motherboard. BIOS is the first program to run when you turn on your
computer.

• BIOS performs the following functions:

1. Initializing and testing hardware in your computer (a process called “POST”,

for Power On Self Test).

2. Loading and running your operating system.

3. Helping your operating system and application programs to manage your

PC hardware by means of a set of routines called BIOS Run-Time Service.

4-2 WHAT IS BIOS SETUP

• Setup is an interactive BIOS program that you need to run when:

1. Changing the hardware on your system. (For example: installing a new

Hard Disk etc.)

2. Modifying the behavior of your computer. (For example: changing the

system time or date, or turning special features on or off etc.)

3. Enhancing your computer’s behavior. (For example: speeding up perfor-

mance by turning on shadowing or caching)

4-3 HOW TO RUN BIOS SETUP

• One way of running SETUP is to press a special function key or key combi­nation during POST, before the operating system is loaded during POST,
the BIOS usually displays a prompt such as:

Press DEL to enter SETUP

CHAPTER 4

BIOS SETUP

65DVB/65DV2

37

4-4 WHAT IS CMOS

• CMOS is a special kind of memory maintained by a battery after you turn
your computer off. The BIOS uses CMOS to store the settings you selected
in SETUP. The CMOS also maintains the internal clock. Every time you
turn on your computer, the BIOS Looks in CMOS for the settings you se­lected and configures your computer accordingly. If the battery charge runs
too low, the CMOS content will be lost and POST will issue a “CMOS in­valid” or “CMOS checksum invalid” message. If this happens, you may
have to replace the battery. After the battery is replaced, the proper set­tings will need to be stored in SETUP.

4-5 WHAT IS POST

• POST is an acronym for Power On Self Test. It’s a traditional name for the
routines that the BIOS uses to test and initializes the devices on your sys­tem when the PC is powered on. Its meanings has grown to include any­thing the BIOS does before the operating system is started. Each of POST
routines is assigned a POST code, an unique number which is sent to I/O
port 080h before the routine is executed.

4-6 BIOS UPGRADE

• Motherboards incorporate the system BIOS in a Flash memory component.
Flash BIOS allows user upgrades without the need to replace an EPROM
component.

• The upgrade utility fits on a floppy diskette and provides the capability to
save, verify, and update the system BIOS. The upgrade utility can be run
from a hard disk drive or a network drive, but no memory managers can be
installed during upgrades.

4-6.1 BEFORE UPGRADE BIOS

• It is recommended that you save a copy of the original motherboard BIOS
along with a Flash EPROM Programming utility (AWDFLASH.EXE) to a
bootable floppy disk in case you need to reinstall the BIOS later.

65DVB/65DV2

38

4-6.2 UPGRADE PROCESS

Note: Normally, to upgrade BIOS that is unnecessary if the system is working fine
without any problem, user should upgrade the BIOS unless you experienced
incompatible problem or need BIOS upgrade to create new features. However,
please read all information in this section before upgrading.

“AWDFLASH.EXE” is a Flash EPROM Programming utility that updates the
BIOS by uploading a new BIOS file to the programmable flash ROM on the
motherboard, This program only works in pure DOS environment, the utility

can not be worked in win95/98, ME, NT or WINDOWS 2000 environment.

Upgrading the system BIOS

Set 1. Pleas visit the board maker’s website, download the newest BIOS file and
newest award flash utility “AWDFLASH.ESE” for the motherboard. The BIOS
file you downloaded will be a *. bin format.

Step 2. Create a bootable diskette. Then copy the BIOS file and award flash utility
“AWDFLASH,EXE” into the diskette.

Step 3. Insert the diskette into drive A, reboot you system and boot form the diskette.

Step 4. When booting is finished type awdflash *.bin/sn/py/cc and then press
<Enter> to run BIOS upgrade program. (*.bin depends on your motherboard
model and version code).

Step 5. After upgraded, please press <F1> or <F10> to exit or reset your system,
Warning ! If there appears Write Fail while Award “FLASH MEMORY
WRITER” verifying Flash memory, just repeat the process, please DO NOT
reset or turn off the system. If the award memory flash utility was not able to
update the BIOS successfully, you system may not able to boot up,

Step 6. You will see a message “CMOS checksum error-Default loaded” during
booting the system. Please press <Del> to run CMOS setup utility, then
reload ‘LOAD SETUP DEFAULTS” or “Load Optimized Defaults” and

save this change.

65DVB/65DV2

39

Figure 1 : Award Flash Memory Writer Start Screen

Figure2 : Award Flash Memory Writer Complete Screen

65DVB/65DV2

40

The parameters of AWDFLASH.EXE

/sn: No original BIOS backup
/py: Program flash memory
/cc: Clear CMOS data after programming
/r : Reset system after programming

NOTE: User can type AWDFLASH /? to get further details about

parameters. Wrong usage of parameter will damage the BIOS
information, so that we strongly recommend user to leave pa­rameters away unless you realize their function.

65DVB/65DV2

41

4-7 CMOS SETUP UTILITY

• This motherboard comes with the AWARD BIOS from AWARD Software
Inc. Enter the CMOS SETUP UTILITY Main Menu by:

1. Turn on or reboot your system. After a series of diagnostic checks, the

following message will appear:

PRESS <DEL> TO ENTER SETUP

2. Press the <DEL> key and the main program screen will appear as follows.

3. Using the arrows on your keyboard, select an option, and press <Enter>.

Modify the system parameters to reflect the options installed in your system.

4. You may return to the Main Menu anytime by pressing <ESC>.

5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and

reboots the system, and “EXIT WITHOUT SAVING” ignores your changes
and exits the program.

CMOS Setup Utility - Copyright (C) 1984 - 2000 Award Software

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Frequency Control

Load Optimized Defaults

Set Supervisor Password

Set User Password

SAVE & EXIT SETUP

EXIT WITHOUT SAVING

Esc : Quit
F10 : Save & Exit Setup (Shift) F2 : Change Color

Time, Date, Hard Disk Type...

: Select Item

65DVB/65DV2

42

• Standard CMOS Setup allows you to record some basic system hardware
configuration and set the system clock and error handling. You only need
to modify the configuration values of this option when you change your
system hardware configuration or the configuration stored in the CMOS
memory gets lost or damaged.

Run the STANDARD CMOS SETUP as following:

1. Choose “STANDARD CMOS SETUP” from the Main Menu and a screen

with a list of option will appear:

2. Use one of the arrow keys to move between options and modify the se-

lected options by using PgUp / PgDn / + / - keys.

4-8 STANDARD CMOS SETUP

Date (mm:dd:yy) Wed, Nov 22 2000
Time (hh:mm:ss) 17 : 11 : 15

IDE Primary Master Press Enter 13022 MB
IDE Primary Slave Press Enter None
IDE Secondary Master Press Enter None
IDE Secondary Slave Press Enter None

Drive A 1.44M, 3.5 in.
Drive B None

Video EGA/VGA
Halt On All Errors
Base Memory 640K
Extended Memory 65472K
Total Memory 1024K

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Standard CMOS Features

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

65DVB/65DV2

43

Time (hh:mm:ss) The time format is based on the 24-hour military-time

clock. For example, 1 p.m. is 13:00:00. Press the
left or right arrow key to move to desired field. Press
the PgUp or PgDn key to increment the setting, or
type the desired value into the field.

Primary / Secondary

Master / Slave

This field records the specifications for all non-SCSI
hard disk drives installed in your system. Refer to the
respective documentation on how to install the drives.

Drive A / Drive B Set this field to the type(s) of floppy disk drive(s) in-

stalled in your system. The choices are:
360KB, 5.25in.,

1.2MB, 5.25in.,
720KB, 3.5in.,

1.44MB, 3.5in.,

2.88MB, 3.5in.,
None.

Video Set this field to the type of video display card installed

in the system. The choices are:
Monochrome,
Color 40x25,
VGA / EGA, (default)
Color 80x25.

Halt On Set this warning feature for the type of errors that will

cause the system to halt. The choices are:
No Errors,
All, But Keyboard,
All, But Diskette,
All, But Disk / Key.

Date (mm:dd:yy) The BIOS determines the day of the week from the

other date information. This field is for information
only.
Press the left or right arrow key to move to the de­sired field (date, month, year). Press the PgUp or
PgDn key to increment the setting, or type the de­sired value into the field.

65DVB/65DV2

44

IDE HDD Auto-Detection Press Enter

IDE Primary Master Auto
Access Mode Auto

Capacity 10243 MB

Cylinder 19846
Head 16
Precomp 65535
Landing Zone 19845
Sector 63

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

IDE Primary Master

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

3. Press <ESC> to return to the Main Menu when you finish setting up all

items.

65DVB/65DV2

45

4-9 ADVANCED BIOS FEATURES

• ADVANCED BIOS FEATURES allows you to improve your system perfor­mance or set up system features according to your preference.

Run the ADVANCED BIOS FEATURES as following:

1. Choose “ADVANCED BIOS FEATURES” from the Main Menu and a screen

with a list of option will appear:

2. Use one of the arrow keys to move between options and modify the se-

lected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the

user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

65DVB/65DV2

46

Virus Warning
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Process or Number Feature
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
OS Select For DRAM > 64MB
Video BIOS Shadow
C8000-CBFFF Shadow
CC000-CFFFF Shadow
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFFF Shadow

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Advanced BIOS Features

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Disabled
Enabled
Enabled
Enabled
Disabled
Enabled
Floppy
HDD-0
CDROM
Enabled
Disabled
Disabled
On
Fast
Disabled
6
250
Setup
Non-OS2
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled

65DVB/65DV2

47

CPU Internal Cache Cache memory is additional memory that is much

faster than conventional DRAM (system memory).
CPUs from 486-type on up contain internal cache
memory, and most, but not all, modern PCs have
additional (external) cache memory. When the CPU
requests data, the system transfers the requested
data from the main DRAM into cache memory, for
even faster access by the CPU.
The External Cache field may not appear if your sys­tem does not have external cache memory.

External Cache Choose Enabled or Disabled. This option allows you

to enable or disable the external cache.

CPU L2 Cache ECC

Checking

When you select Enabled, memory checking is en­able when the external cache contains ECC SRAMs.
The choice: Enabled, Disabled.

Quick Power On Self

Test

Select Enabled to reduce the amount of time required
to run the power-on self -test (POST). A quick POST
skips certain steps. We recommend that you nor­mally disable quick POST. Better to find a problem
during POST than lost data during your work.

Process or Number

Feature

The choice: Enabled, Disabled.

Virus Warning Enabled: Activates automatically when the system

boots up causing a warning message to
appear if there is anything attempting to
access the boot sector or hard disk parti­tion table.

Disabled: No warning message will appear when there

is something attempting to access the boot
sector or hard disk partition table.

NOTE: Many diagnostic (or boot manager) programs which at-

tempt to access the boot sector table can cause the above
warning message. If you will be running such a program,
we recommend that you disable the virus protection first.

65DVB/65DV2

48

Gate A20 Option Gate A20 refers to the way the system addresses

memory above 1 MB (extended memory). When set
to Fast, the system chipset controls Gate A20. When
set to Normal, a pin in the keyboard controller con­trols Gate A20. Setting Gate A20 to Fast improves
system speed, particularly with OS/2 and Windows.

Typematic Rate Setting When Disabled, the following two items (Typematic

Rate and Typematic Delay) are irrelevant. Keystroke
repeat at a rate determined by the keyboard control­ler in your system.
When Enabled, you can select a typematic rate and
typematic delay.

Typematic Rate (Chars

/ Sec)

Range between 6 and 30 characters per second. This
option controls the speed of repeating keystrokes.

Boot Up NumLock

Status

Toggle between On or Off to control the state of the
NumLock key when the system boots. When toggled
On, the numeric keypad generates numbers instead
of controlling cursor operations.

Boot Up Floppy Seek Enabled: During POST, BIOS checks the track num-

ber of the floppy disk drive to see whether
it is 40 or 80 tracks.

Disabled: During POST, BIOS will not check the track

number of the floppy disk drive.

Swap Floppy Drive This field is effective only in systems with two floppy

drives. Selecting Enabled assigns physical drive B
logical drive A, and physical drive A to logical drive B.

First/Second/Third/

Other Boot Device

The BIOS attempts to load the operating system from
the devices in the sequence selected in these items.
The choice: Floppy, LS/ZIP, HDD, SCSI, CDROM,

Disabled.

65DVB/65DV2

49

Typematic Delay

(Msec)

Choose 250, 500, 750 and 1000. This option sets
the time interval for displaying the first and the sec­ond characters.

Security Option If you have set a password, select whether the pass-

word is required every time the System boots, or only
when you enter setup.

OS Select For DRAM >

64MB

Non-OS/2: For Non-OS/2 system.
OS: For OS/2 operating system.

Video BIOS Shadow Enabled copies Video BIOS to shadow RAM for im-

proving performance.
The choice: Enabled, Disabled.

C8000-CBFFF to

DC000-DFFFF Shadow

These options are used to shadow other expansion
card ROMs.

3. Press <ESC> to return to the Main Menu when you finish setting up all

items.

65DVB/65DV2

50

• ADVANCED CHIPSET FEATURES allows you to change the values of

chipset registers. These registers control the system options.

Run the ADVANCED CHIPSET FEATURES as following:

1. Choose “ADVANCED CHIPSET FEATURES” from the Main Menu and a

screen with a list of option will appear:

2. Use one of the arrow keys to move between options and modify the se-

lected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the

user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

4-10 ADVANCED CHIPSET FEATURES

65DVB/65DV2

51

Bank 0/1 DRAM Timing SDRAM 10ns
Bank 2/3 DRAM Timing SDRAM 10ns
Bank 4/5 DRAM Timing SDRAM 10ns
SDRAM Cycle Length 3
DRAM Clock Host CLK
Memory Hole Disabled
Read Around Write Disabled
Concurrent PCI/Host Disabled
System BIOS Cacheable Disabled
Video RAM Cacheable Disabled
AGP Aperture Size 64M
AGP 2X Mode Enabled
CPU to PCI Write Buffer Enabled
PCI Dynamic Bursting Disabled
PCI Master 0 WS Write Enabled

PCI Delay Transaction Enabled
PCI#2 Access #1 Retry Enabled

AGP Master 1 WS Write Disabled
AGP Master 1 WS Read Disabled
USB Keyboard Support Disabled
OnChip Sound Enabled
OnChip Modem Disabled
OnChip USB Enabled

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Advanced Chipset Features

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

65DVB/65DV2

52

System BIOS

Cacheable

Choose Enabled or Disabled. When enabled, the
access to the system BIOS ROM addressed at
F0000H - FFFFFH is cached.

SDRAM Cycle Length

Time

You can select CAS latency time in HCLKs of 2/2 or
3/3. The system board designer should have set the
values in this field, depending on the DRAM installed.
Do not change the values in this field unless you
change specifications of the installed DRAM or the
installed CPU.

Memory Hole In order to improve performance, certain space in

memory is reserved for ISA cards. This memory must
be mapped into the memory space below 16MB.
The choice: 15M-16M, Disabled.

DRAM Clock This item allows you to control the DRAM speed.

The choice: Host Clock, HCLK+33M, HCLK-33M.

Bank 0/1 2/3 4/5 DRAM

Timing

This item allows you to select the value in this field,
depending on whether the board has paged DRAMs
or EDO (Extended Data Output) DRAMs.
The choice: SDRAM 8/10ns,

Normal,
Medium,
Fast,
Turbo.

Read Around Write DRAM optimization feature: If a memory read is ad-

dressed to a location whose latest write is being held
in a buffer before being written to memory, the read
is satisfied through the buffer contents, and the read
is not sent to the DRAM.

Concurrent PCI/Host Please leave it at default setting

65DVB/65DV2

53

CPU to PCI Write

Buffer

When this field is Enabled, writes from the CPU to
the PCI bus are buffered, to compensate for the speed
differences between the CPU and the PCI bus. When
Disabled, the writes are not buffered and the CPU
must wait until the write is complete before starting
another write cycle.
The choice: Enabled, Disabled.

PCI Dynamic Bursting When Enabled, every write transaction goes to the

write buffer. Bursting transactions then burst on the
PCI bus and non-bursting transactions don’t.
The choice: Enabled, Disabled.

PCI Master 0 WS Write When Enabled, writes to the PCI bus are executed

with zero wait states.
The choice: Enabled, Disabled.

PCI Delay Transaction Leave this field at default

PCI #2 Access #1 Retry Leave this field at default

AGP Master 1 ws write Leave this field at default

AGP Master 1 ws read Leave this field at default

AGP Aperture Size Choose 4, 8, 16, 32, 64, 128 or 256 MB. Memory

mapped and graphics data structures can reside in a
Graphics Aperture. This area is like a linear buffer.
BIOS will automatically report the starting address of
this buffer to the O.S.

AGP-2X Mode This item allows you to enable / disable the AGP-2X

mode.

Video RAM Cacheable Choose Enabled or Disabled. When enabled, the

access to the VGA RAM addressed is cached.

65DVB/65DV2

54

3. Press <ESC> to return to the Main Menu when you finish setting up all

items.

OnChip USB This should be enabled if our system has a USB in-

stalled on the system board and you wish to use it.
Even when so equipped, if you add a higher perfor­mance controller, you will need to disable this feature.
The choice: Enabled, Disabled.

OnChip Sound Select Enabled to use the on-chip Audio capability of

your system. Most of the following field do not
appear when this field is Disabled, for user who wants
to use another sound card, this field must be Disabled.

USB Keyboard

Support

Enabled: Enable function when the USB keyboard is

being used.

Disabled: When the AT keyboard is being used,

choose disabled.

OnChip Modem Select Enabled to use the on-chip Modem capability

of your system. This field must be Disabled, if there
is NO AMR modem card installed.

65DVB/65DV2

55

• INTEGRATED PERIPHERALS option allows you to get some informations

inside your system when it is working.

Run the INTEGRATED PERIPHERALS as following:

1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a screen

with a list of option will appear:

4-11 INTEGRATED PERIPHERALS

On-Chip IDE Channel 0
On-Chip IDE Channel 1
IDE Prefetch Mode
Primary Master PIO
Primary Slave PIO
Secondary Master PIO
Secondary Slave PIO
Primary Master UDMA
Primary Slave UDMA
Secondary Master UDMA
Secondary Slave UDMA
Init Display First
IDE HDD Block Mode
Onboard FDD Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART 2 Mode
IR Function Duplex
TX, RX inverting enable
Onboard Parallel Port
Onboard Parallel Mode
ECP Mode Use DMA
Parallel Port EPP Type
Onboard Legacy Audio
Sound Blaster
SB I/O Base Address
SB IRQ Select
SB DMA Select
MPU-401
MPU-401 I/O Address
Game Port (200-207H)

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Integrated Peripherals

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Enabled
Enabled
Enabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
PCI Slot
Enabled
Enabled
Auto
Auto
Standard
Half
No, Yes
378/IRQ7
Normal
3
EPP1.9
Enabled
Disabled
220H
IRQ 5
DMA 1
Disabled
330-333H
Enabled

65DVB/65DV2

56

On-Chip Primary/

Secondary PCI IDE

The chipset contains a PCI IDE interface with sup­port from two IDE channels. Select Enabled to acti­vate the first and/or the second IDE interface. Select
Disabled to deactivate an interface if you install a pri­mary and/or second add-on IDE interface.
The choice: Enabled, Disabled.

Primary

Master / Slave PIO

Secondary

Master / Slave PIO

Choose Auto or Mode 0~4. The BIOS will detect the
HDD mode type automatically when you choose Auto.
You need to set to a lower mode than Auto when your
hard disk becomes unstable.
The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3,

Mode 4.

IDE Prefetch Mode The onboard IDE drive interfaces supports IDE

prefetching for faster drive accesses. If you install a
primary and/or secondary add-in IDE interfaces, set
this field to Disabled if the interface does not support
prefetching.
The choice: Enabled, Disabled.

2. Use one of the arrow keys to move between options and modify the se-

lected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the

user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

65DVB/65DV2

57

Primary

Master / Slave UDMA

Secondary

Master / Slave UDMA

Ultra DMA/66 implementation is possible only if your
IDE hard drive supports it and the operating environ­ment includes a DMA drive and your system software
both support Ultra DMA/66, select Auto to enable
BIOS support.
The choice: Auto, Disabled.

Init Display First This option allows you to decide to activate PCI Slot

or AGP first.
The choice: PCI Slot, AGP.

IDE HDD Block Mode Block mode is also called block transfer, multiple

commands, or multiple sector read/write. If your IDE
hard drive supports block mode (most new drives do),
select Enabled for automatic detection of the optimal
number of block read/write per sector the drive can
support.
The choice: Enabled, Disabled.

Onboard FDC

Controller

Select Enabled if your system has a floppy drive con­troller (FDC) installed on the system board and you
want to use it. If you install add-in FDC or the system
has no floppy drive, select Disabled in this field.
The choice: Enabled, Disabled.

Onboard Serial

Port 1 / Port 2

Select an address and corresponding interrupt for the
first and second serial ports.
The choice: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/

IRQ3, Disabled, Auto.

UART 2 Mode This item allows you to select which mode for the

Onboard Serial Port 2.
The choice: Standard, HPSIR, ASKIR

IR Function Duplex This item allows you to select the IR half / full duplex

function.
The choice: Half, Full.

65DVB/65DV2

58

3. Press <ESC> to return to the Main Menu when you finish setting up all

items.

Onboard Legacy Audio This field controls the onboard audio.

• Sound Blaster

• SB I/O Base Address

• SB IRQ Select

• SB DMA Select

• MPU-401

• MPU-401 I/O Address

• Game Port (200-207H)

Parallel Port EPP Type Select EPP port type 1.7 or 1.9

The choice: EPP1.7, 1.9.

Onboard Parallel Port This item allows you to determine onboard parallel

port controller I/O address setting.
The choice: 378H/IRQ7, 278H/IRQ5, 3BC/IRQ7,

Disabled.

0nboard Parallel Port

Mode

Select an operating mode for the onboard parallel
(printer) port. Select Normal, Compatible, or SPP
unless you are certain your hardware and software
both support one of the other available modes.
The choice: SPP, EPP, ECP, ECP + EPP.

ECP Mode Use DMA Select a DMA channel for the parallel port for use

during ECP mode.
The choice: 3, 1.

TX, RX inverting

enabled

This item allows you to enable the TX, RX inverting
which depends on different H/W requirement. This
field is not recommended to change its default set­ting for avoiding any error in your system.
The choice: “No, No”, “No, Yes”, “Yes, No”, “Yes, Yes”.

65DVB/65DV2

59

• POWER MANAGEMENT SETUP allows you to set the system’s power

saving functions.

Run the POWER MANAGEMENT SETUP as following:

1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a

screen with a list of option will appear:

2. Use one of the arrow keys to move between options and modify the se-

lected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the

user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

4-12 POWER MANAGEMENT SETUP

ACPI Function
Power Management
PM Control by APM
Video Off Option
Video Off Method
MODEM Use IRQ
Doze Mode
Soft-Off by PWRBTN
State After Power Failure
Wake Up Events

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Power Management Setup

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Enabled
Press Enter
Yes
Suspend Off
V/H SYNC+Blank
3
Disable
Instand-Off
Auto
Press Enter

65DVB/65DV2

60

ACPI Function Select Enabled only if your computer’s operating sys-

tem supports the Advanced Configuration and Power
Interface (ACPI) specification. Currently, Windows
NT 5.0 support ACPI.

HDD Power Down When enabled and after the set time of system

inactivity, the hard disk drive will be powered down
while all other devices remain active.

Power Management User Define
HDD Power Down Disable
Doze Mode Disable
Suspend Mode Disable

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Power Management

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Power Management This option allows you to select the type (or degree)

of power saving for Doze, Standby, and Suspend
modes.
This table describes each power management mode:

Max Saving Maximum power savings. Only Available for SL CPUs.

Inactivity period is 1 minute in each mode.

User Define Set each mode individually. Select time-out periods

in the section for each mode, below.

Min Saving Minimum power savings. Inactivity period is 1 hour

in each mode (except the hard drive).

65DVB/65DV2

61

PM Control by APM When enabled, an Advanced Power Management

device will be activated to enhance the Max. Power
Saving mode and stop the CPU internal clock, If Ad­vanced Power Management (APM) is installed on your
system, selecting Yes gives better power savings. If
the Max. Saving is not enabled, this will be present to
No.

Video Off Option When enabled, this feature allows the VGA adapter

to operate in a power saving mode.

nOsyawlA .sedomgnivasrewopgnirudnoniamerlliwrotinoM

ffO>--dnepsuS

dnepsuSehtsretnesmetsysehtnehwdeknalbrotinoM

.edom

ffO>--ybtS,psuS

rodnepsuSrehtiesretnemetsysehtnehwdeknalbrotinoM

.sedomybdnatS

Video Off Method This determines the manner in which the monitor is

blanked.

knalB+CNYSH/V

lacitrevehtffonrutotmetsysehtesuaclliwnoitcelessihT

ehtotsknalbetirwdnastropnoitazinorhcnyslatnozirohdna

.reffuboediv

neercSknalB .reffuboedivehtotsknalbsetirwylnonoitposihT

SMPD

rewoPyalpsiDehtstroppusrotinomruoyfinoitposihttceleS

oediVehtfodradnats)SMPD(gnilangiStnemeganaM

tnemeganamrewopoedivtcelesotsdradnatSscinortcelE

.seulav

Doze Mode When enabled and after the set time of system

inactivity, the CPU clock will run at slower speed while
all other devices still operate at full speed.

Suspend Mode After the selected period of system inactivity, the

chipset enters a hardware suspend mode, stopping
the CPU clock and possibly causing other system
devices to enter power management modes.

65DVB/65DV2

62

VGA When Enabled, you can set the VGA awakens the

system

State After Power

Failure

This field lets you determine the state that your PC
returns to after a power failure.
The choice: On, Off, Auto

VGA
LPT & COM
HDD & FDD
PCI Master
Modeam Ring Resume
RTC Alarm Resume
Date (of Month)
Resume Time (hh:mm:ss)
IRQS Activity Monitoring

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Wake Up Events

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

OFF
LPT/COM
ON
OFF
Disabled
Disabled
0
0 0 0
Press Enter

Soft-Off by PWRBTN Instant-Off : Turn off the system power at once after

pushing the power button.
Delay 4 Sec: Turn off the system power 4 seconds
after pushing the power button. (To meet PC97/98
spec)

MODEM Use IRQ Name the interrupt request (IRQ) line assigned to the

modem (if any) on your system. Activity of the se­lected IRQ always awakens the system.
The choice: 3, 4, 5, 7, 9, 10, 11, NA.

65DVB/65DV2

63

RTC Alarm Resume When Enabled, you can set the data and time at the

which the RTC (Real Time Clock) alarm awakens the
system from suspend mode.
The choice: Disabled, Enabled.

Date (of Month) Set a certain date when RTC Alarm Resume option

is Enabled to awaken the system. This option is con­current with Resume Time option.

Resume Time (hh:mm:

ss)

Set a certain time when RTC Alarm Resume option is
Enabled to awaken the system. This option is con­current with Date option.

Modem Ring Resume An input signal on the serial Ring Indicator (RI) Line

(in other words, an incoming call on the modem) Awak­ens the system from a soft off state.

HDD & FDD When On of HDD & FDD, any activity from one of the

listed system peripheral devices wakes up the system.

PCI Master When On of PCI Master, any activity from one of the

listed system peripheral devices wakes up the system.

LPT & COM When On of LPT & COM, any activity from one of the

listed system peripheral devices or IRQs wakes up
the system.

65DVB/65DV2

64

3. Press <ESC> to return to the Main Menu when you finish setting up all

items.

Primary INTR ON
IRQ 3 (COM2) Primary
IRQ 4 (COM1) Primary
IRQ 5 (LPT2) Primary
IRQ 6 (Floppy Disk) Primary
IRQ 7 (LPT1) Primary
IRQ 8 (RTC Alarm) Disabled
IRQ 9 (IRQ2 Redir) Secondary
IRQ 10 (Reserved) Secondary
IRQ 11 (Reserved) Secondary
IRQ 12 (PS/2 Mouse) Primary
IRQ 13 (Coprocessor) Disabled
IRQ 14 (Hard Disk) Primary
IRQ 15 (Reserved) Disabled

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

IRQ Activity Monitoring

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

The following is a list of IRQ’s (Interrupt Requests), which can be exempted
much as the COM ports and LPT ports above can. When an I/O device
wants to gain the attention of the operating system, it signals this by causing
an IRQ to occur. When the operating system is ready to respond to the
request, it interrupts itself and performs the service. When set On, activity
will neither prevent the system from going into a power management mode
nor awaken it.

65DVB/65DV2

65

• PNP/PCI CONFIGURATION allows you to set the system’s power saving

functions.

Run the PNP/PCI CONFIGURATION as following:

1. Choose “PNP/PCI CONFIGURATION” from the Main Menu and a screen

with a list of option will appear:

2. Use one of the arrow keys to move between options and modify the se-

lected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change color.
<F5>: Get the previous values. These values are the values with which the

user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

4-13 PNP / PCI CONFIGURATION

PNP OS Installed
Reset Configuration Data

Resources Controlled By
IRQ Resources
DMA Resources

PCI/VGA Palette Snoop
Assign IRQ For VGA
Assign IRQ For USB

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

PnP/PCI Configurations

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

No
Disabled

Auto(ESCD)
Press Enter
Press Enter

Disabled
Enabled
Enabled

65DVB/65DV2

66

Resource ControlledByThe plug and play AwardBIOS can automatically con-

figure all the boot and play-compatible devices. If
you select Auto, all the interrupt request (IRQ) and
DMA assignment fields disappear, as the BIOS auto­matically assigns them.

Reset Configuration

Data

Normally, you leave this Disabled. Select Enabled to
reset Extended System Configuration Data (ESCD)
when you exit Setup if you have installed a new add­on and the system reconfiguration has caused such
a serious conflict that the operating system cannot
boot.

PNP OS Installed Select Yes if the system operating environment is

Plug-and Play aware (e.g., Windows 95).

NOTE: BIOS will automatically disable all PnP resources except

the boot device card when you select Yes on Non-PnP
operating system.

IRQ Resources Press Enter. Please refer to the below list.

IRQ-3 assigned to PCI/ISA PnP
IRQ-4 assigned to PCI/ISA PnP
IRQ-5 assigned to PCI/ISA PnP
IRQ-7 assigned to PCI/ISA PnP
IRQ-9 assigned to PCI/ISA PnP
IRQ-10 assigned to PCI/ISA PnP
IRQ-11 assigned to PCI/ISA PnP
IRQ-12 assigned to PCI/ISA PnP
IRQ-14 assigned to PCI/ISA PnP
IRQ-15 assigned to PCI/ISA PnP

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

IRQ Resources

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

65DVB/65DV2

67

DMA Resources Press Enter. Please refer to the below list.

Assign IRQ for USB Enabled: Add one IRQ to USB controller.

Disabled: Remove IRQ from USB controller. The sys­tem will have extra IRQ for other devices but the USB
controller will still not be disabled. (only IRQ was
removed)

Assign IRQ for VGA Enabled: Add one IRQ to VGA controller.

Disabled: Remove IRQ from USB controller. The sys­tem will have extra IRQ for other devices but the VGA
controller will still not be disabled. (Only IRQ was
removed)

3. Press <ESC> to return to the Main Menu when you finish setting up all

items.

PCI/VGA Palette Snoop Leave this field at Disabled.

The choice: Enabled, Disabled.

DMA-0 assigned to PCI/ISA PnP
DMA-1 assigned to PCI/ISA PnP
DMA-3 assigned to PCI/ISA PnP
DMA-5 assigned to PCI/ISA PnP
DMA-6 assigned to PCI/ISA PnP
DMA-7 assigned to PCI/ISA PnP

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

DMA Resources

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

65DVB/65DV2

68

4-14 PC HEALTH STATUS

• This section helps you to get more information about your system including

CPU temperature, FAN speed and voltage. It is recommended that you
contact with your motherboard supplier to get proper value about your set­ting of the CPU temperature.

Current CPU Temp. Shows current CPU temperature.

Current System Temp. Shows current system temperature.

Current CPU FAN1

Speed

Shows current CPU FAN1 speed. The fan must pro­vide rotary pulse. (Normally these types of fan have
a three-wire connector)

Current CPUFAN2

Speed

Shows current CPUFAN2 speed. The fan must pro­vide rotary pulse. (Normally these types of fan have
a three-wire connector)

Vcore Shows power supply actual voltage value.

• Press <ESC> to return to the Main Menu when you finish setting up all
items.

Current CPU Temp
Current System Temp
Current CPUFAN1 Speed
Current CPUFAN2 Speed
Vcore

2.5V

3.3V
5V
12V

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

PC Health Status

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

65DVB/65DV2

69

Auto Detect

DIMM/PCI CLK

This item allows you to enable/disable detect DIMM/
PCI Clock.
The choice: Enabled, Disabled.

Spread Spec-

trum Modulated

This item allows you to enable/disable the spread
spectrum modulate.
The choice: Enabled, Disabled.

CPU Host Clock

(CPU/PCI)

This item allows you to select CPU/PCI frequency.
The choice: Default, 100/33MHz, 103/34MHz, 105/
35MHz, 112/37MHz, 115/38MHz, 120/40MHz, 124/
41MHz.

• Press <ESC> to return to the Main Menu when you finish setting up all
items.

Auto Detect DIMM/PCI CLK Disabled
Spread Spectrum  Disabled
CPU Host Clock (CPU/PCI) Default

Item Help

Menu Level

CMOS Setup Utility - Copyright (C) 1984-2000 Award Software

Frequency Control

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

4-15 FREQUENCY/VOLTAGE CONTROL

65DVB/65DV2

70

4-16 LOAD OPTIMIZED DEFAULTS

• When you press <Enter> on this item you get a confirmation dialog box

with a message similar to:

“ Load Optimized Defaults (Y / N) ? N ”

Pressing “Y” loads the BIOS default values that are factory settings for opti-

mal performance system operations.

65DVB/65DV2

71

4-17 SET SUPERVISOR / USER PASSWORD

• These two options allow you to set your system passwords. Normally, the

supervisor has a higher ability to change the CMOS setup option than the
user. The way to set up the passwords for both Supervisor and User are
as follows:

1. Choose “Change Password” in the Main Menu and press <Enter>. The

following message appears:

“Enter Password : “

2. The first time you run this option, enter your password up to 8 characters

and press <Enter>. The screen does not display the entered characters.

3. After you enter the password, the following message appears prompting

you to confirm the password:

“Confirm Password : “

4. Enter the same password “exactly” as you just typed again to confirm the

password and press <Enter>.

5. Move the cursor to Save & Exit Setup to save the password.

6. If you need to delete the password or entered before, choose the Super-

visor Password and press <Enter>. It will delete the password that you
had before.

7. Move the cursor to Save & Exit Setup to save the option you did, other-

wise the old password will still be there the next time you turn your system
on.

8. Press <Enter> to exit to the Main Menu.

NOTE: If you forget or lose the password, the only way to access

the system is to clear the CMOS RAM. All setup informa­tions will be lost and you need to run the BIOS setup pro­gram again.

65DVB/65DV2

72

• SAVE & EXIT SETUP allows you to save all modifications you have speci-

fied into the CMOS memory. Highlight this option on the Main Menu and
the following message appears:

“SAVE to CMOS and EXIT (Y/N) ? Y “

Press <Enter> key to save the configuration changes.

4-19 EXIT WITHOUT SAVING

• EXIT WITHOUT SAVING option allows you to exit the Setup Utility without

saving the modifications that you have specified. Highlight this option on
the Main Menu and the following message appears:

“Quit Without Saving (Y/N) ? N “

You may change the prompt to “Y” and press <Enter> key to leave this op­tion .

4-18 SAVE & EXIT SETUP