Page 1
his User‘s Guide & Technical Reference is for assisting system
T
manufacturers and end-users in setting up and installing the
mainboard.
Every effort has been made to ensure that the information in this manual
is accurate. Soltek Computer Inc. is not responsible for printing or
clerical errors. Information in this document is subject to change without notice and does not represent a commitment on the part of Soltek
Computer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identification purpose only. Product names appearing in this manual may or
may not be registered trademarks or copyrights of their respective
companies.
oltek computer inc. Provides this manual “As is “ without war
S
ranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall Soltek computer inc.
Be liable for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or consequential damages of any kind, even if Soltek computer inc. Has been
advised of the possibility of such damages arising from any defect or
error in this manual or product.
R
© Copyright 2000 Soltek Computer Inc.
All rights reserved.
Model : SL-65DV
Edition : March 2000
Version : 2.0
http://www.soltek.com.tw
e-mail: support@soltek.com.tw
Page 2
65DV
CONTENT
Default setting: Intel Celeron 300A/66MHz; Pentium II/III 450/
100MHz..................................................................................... 5
SW1 DIP1 ~ DIP4: Bus Ratio Select ...................................... 7
SW1 DIP5 ~ DIP6: Bus Clock Select ..................................... 7
Onboard AC’97 Audio Codec Controller driver installation..
................................................................................................ 11
STANDARD CMOS SETUP.................................................... 13
BIOS FEATURES SETUP ...................................................... 1 5
CHIPSET FEATURES SETUP ............................................... 19
POWER MANAGEMENT SETUP........................................... 22
PnP/PCI CONFIGURATION SETUP ...................................... 26
LOAD SETUP DEFAULTS ..................................................... 29
CPU SPEED SETTING .......................................................... 30
INTEGRA TED PERIPHERALS............................................... 32
SUPERVISOR/USER PASSWORD........................................ 36
IDE HDD AUTO DETECTION ................................................ 37
SAVE & EXIT SETUP............................................................. 37
2
Page 3
65DV
EXIT WITHOUT SA VING........................................................ 37
Appendix A
Flash Memory Update Installation ....................................... 38
Appendix B
Driver installation .................................................................. 39
Appendix C
THERMAL SENSOR CONNECTOR ...................................... 41
3
Page 4
65DV
4
SL-65DV
VIA 82C693A SOCKET-370
F E A T U R E
PROCESSOR
Supports Intel PPGA Celeron 370 / FC-PGA Pentium III
(Coppermine) CPUs 300 ~ 750 MHz or higher.
Supports 66/ 75*/ 83*/ 100/ 103*/ 105*/ 124*/ 133/ 140*/ 150*MHz
system bus speeds.
Clock multipliers up to 8x.
CHIPSET
VIA 82C693A + 686A (133MHz FSB ).
ONBOARD SOUND
Built-In AC’97 Audio Codec.
Supports Line-In, Mic-In, Speaker-Out / Line-Out connector
and MIDI port.
SYSTEM MEMORY
3x 3.3V DIMM sockets.
8MB to 768MB DRAM size.
ECC or Parity support.
SLOT
1x AGP slot supports 1x / 2x mode bus; 1x AMR (Audio
Modem Riser)slot; 5x PCI Bus Master slots; 1x ISA slot.
ONBOARD I/O
2x Ultra A T A33/66 Bus Master IDE ports.
4x USB ports.
1x PS/2 mouse connector and 1x PS/2 keyboard connector.
1x 2.88MB Floppy port, 2x High Speed 16550A UART ports
and 1x IrDA TX / RX Header.
POWER
ATX power supply connector.
Power-On by LAN(WOL), RTC Alarm, Modem Ring.
BIOS
2MB FLASH BIOS.
Licensed AW ARD BIOS, supports SCSI / ZIP / LS-120 / CDROM boot and ACPI Power Management.
FORM FACTOR / PCB
ATX, 4 layers PCB, 18.5cm x 30.5cm size.
OTHER FEATURES
Hardware Monitor.
Supports BIOS Writing Protection.
Page 5
upper
PS/2
MOUSE
upper
USB0
COM2 COM1
LINE
LINE
MIC
1 4
1 4
1 3
1 3
lower
lower
OUT
IN
JP9
JP8
PS/2
USB1
CD_IN2
CD_IN1
AC'97
Codec
K/B
2 16
1 15
LPT1
GAME/MIDI PORT
FAN1
USB2
JP3
JP4
ATX POWER
ON DIP
1 3
1 3
JP6
JP7
SW1
1 2 3 4 5 6
AMR
1 3
1 3
1 3
JP5
RT1
MOTHERBOARD DIAGRAM
1 3
1 3
1 3
DIMM1
DIMM2
VIA
686A
DIMM3
JP11
1
3
FDC1
Battery
RT2
Clock
Generator
Li
IDE2
JBAT1
VIA
693A
PCI 1
PCI 2
PCI 3
PCI 4
JP14
JP13
JP12
SOCKET 370
AGP
65DV
IDE1
FAN2
1 3
FLASH BIOS
JWOL1
PCI 5
ISA
HD/LED IR PWR SUSPEND
1 1
J2 J3
SPK RST PWR/LED SUSLED
Default setting: Intel Celeron 300A/66MHz; Pentium II/III 450/
100MHz.
NOTE: For 100MHz/133MHz CPU environment, the SDRAM sepc must comply with
PC-100/PC-133 spec.
5
Page 6
65DV
CPU Type Configuration
CPU CLOCK SETTING
CPU MODEL SW1 CPU RATIO
ONONON
OFF
OFF
OFF
1 2 3 4 5 6
ONONON
OFF
OFF
1 2 3 4 5 6
ONONON
OFF
OFF
OFF
1 2 3 4 5 6
OFF
OFF
OFF
1 2 3 4 5 6
ON
OFF
OFF
OFF
OFF
1 2 3 4 5 6
ONONON
OFF
OFF
1 2 3 4 5 6
ON
ON
OFF
OFF
OFF
1 2 3 4 5 6
ONONON
OFF
OFF
OFF
1 2 3 4 5 6
ON
OFF
OFF
OFF
OFF
1 2 3 4 5 6
ONONON
OFF
OFF
OFF
1 2 3 4 5 6
3.5x
ON
4.0x
4.5x
ONONON
5.0x
ON
5.5x
ON
6.0x
ON
6.5x
7.0x
ON
7.5x
8.0x
Celeron 233/66
Celeron 266/66
Pentium III 533EB/133*
Celeron 300/66
Pentium III 600EB/133*
Celeron 333/66
Pentium III 500E/100*
Pentium III 667B/133*
Celeron 366/66
Pentium III 550E/100*
Pentium III 733B/133*
Celeron 400/66
Pentium III 600E/100*
Celeron 433/66
Pentium III 650/100*
Celeron 466/66
Pentium III 700/100*
Celeron 500/66
Pentium III 750/100*
Celeron 533/66
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
* : Pentium III Coppermin FC-PGA CPUs.
6
Page 7
SW1 DIP1 ~ DIP4: Bus Ratio Select
65DV
ONONON
ON
3.0x
OFF
14
ON
ON
3.5x
4.0x
ON
ON
OFF
OFF
4
1
ONONON
OFF
14
ON
ON
4.5x
5.0x
ON
ON
OFF
1
OFF
OFF
4
ON
ON
OFF
14
ON
ON
OFF
OFF
5.5x
OFF
4
1
SW1 DIP5 ~ DIP6: Bus Clock Select
6.0x
6.5x
7.0x
7.5x
8.0x
ONONON
ON
14
ON
ON
1
ON
ON
14
ON
ON
1
ON
OFF
14
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
4
OFF
OFF
4
OFF
SW1 DIP5 ~ DIP6 JP11: FSB Select
66/100/133MHz
Auto Select
(default)
100MHz
133MHz
ON
ON
ON
OFF
1 2 3 4 5 6
OFF
1 2 3 4 5 6
OFF
1 2 3 4 5 6
ON
OFF
ON
1
3
1
3
1
3
7
Page 8
65DV
JUMPER SETTING
A1 A2
--
++
J2
1
1
J3
EF
A1: 1st HDD LED
B. : INFRARED (IR)
D. : NONE
F. : RESET SWITCH
H. : NONE
B
+
G
A2: 2nd HDD LED
C. : POWER SWITCH
E. : SPEAKER
G. : POWER LED
I. : SUSPEND LED
C
-
H I
FAN#: Onboard FAN (12V) Connector.
FAN# FUNCTION
FAN1 CPU FAN
FAN2 SYSTEM FAN
JP3 / JP4: USB Port Select (1)
USB Port Select JP3 / JP4
Redirect USB port3 to
USB2 connector (default)
Redirect USB port3 to
AMR
D
15
15
1 3
JP3
JP4
1 3
1 3
JP3
JP4
1 3
JP6 / JP7: USB Port Select (2)
USB Port Select JP6 / JP7
Redirect USB port2 to
USB2 connector (default)
Redirect USB port2 to
AGP
8
JP6
JP7
JP6
JP7
1 3
1 3
1 3
1 3
Page 9
JP5 / JP9: AC’97 Codec Control
AC’97 Codec JP5 / JP9
Disabled
Enabled (default)
1 3
JP5 JP9
1 3
JP5 JP9
JP8: Power Lost Resume
This feature must work with BIOS. Please refer to the BIOS “Power On
After PWR-Fail” sector.
Power Lost Resume JP8
65DV
3
1
3
1
Enabled
Normal (default)
JP12 / JP13 / JP14: Intel / Cyrix CPU Select
CPU Type
Intel CPU (default)
Cyrix JOSHUA CPU
JP12
JP13
3
1
3
1
3
1
3
1
JBAT1: Clear CMOS Data
Before you clear the CMOS data, it’s necessary to turn the power off first
(including +5V standby power). Otherwise, the system may work
abnormally or malfunction.
CMOS Status JBAT1
Retain Data (default)
Clear CMOS Data
3
1
3
1
JP14
3
1
3
1
3
1
3
1
9
Page 10
65DV
CD_IN1/CD_IN2: CD-ROM Audio Connector
CD_IN2PIN # CD_IN1
PIN 1 Left Channel
PIN 2 GND
PIN 3
PIN 4 Right Channel
GND
Left Channel
GND
Right Channel
GND
RT2: Thermal Sensor Connector
GAME/MIDI Port:
Connect joystick or MIDI to this connector.
MIC :Microphone Jack
Connect to microphone device.
LINE IN: Audio In Jack
Connect audio line in.
LINE OUT/SPEAKER OUT: Audio Out Jack
Connect audio line out or speaker out.
JWOL1: Wake On LAN (WOL) Connector
This connector is designed to boot up system via LAN. Connect the wake
on signal form the LAN card to this connector.
10
Page 11
DRIVERS & SOFTWARES INSTALLATION
Onboard AC’97 Audio Codec Controller driver installation
For Windows95 / Windows98:
1. Go to CD-ROM directory, we suggest that’s D:\.
2. Find and run D:\DRIVER\AUDIO\VIA AC97\SETUP.EXE or 68USR1XX.EXE
3. The installation will detect your O.S. to install relative files into your
system.
4. Reboot the computer.
65DV
NOTE 1: IF USER WANTS TO USE EXTERNAL SOUND CARD, USER MUST RUN
NOTE 2: UNDER WINDOWS 95, USER MUST INSTALL DirectX AND USBSUPP.EXE
NOTE 3: “VIA Patch Code”, “VIA AGP VxD Driver” & “VIA PCI IRQ Routing
BIOS PROGRAM TO DISABLE “Onchip Sound” OPTION IN THE “Chipset
Feature Setup” AND “Onboard Legacy Audio” OPTION IN THE
“Integrated Pheripherals”.
FOR AGP ENVIRONMEMT.
Miniport” installation, please refer to Appendix B.
11
Page 12
65DV BIOS
This VIA 82C693A chipset comes with the AWARD BIOS from AWARD Software Inc. Enter the AWARD BIOS program Main Menu by:
1. Turn on or reboot the system. After a series of diagnostic checks, the
following message will appear:
PRESS <DEL> TO ENTER SETUP
2. Press the <DEL> key and the main program screen will appear as follows:
ROM PCI/ISA BIOS (2A6LGSNC)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD SETUP DEFAULTS
CPU SPEED SETTING
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Esc : Quit
F10 : Save & Exit Setup
: Select Item
(Shift)F2 : Change Color
3. Using the arrows on your keyboard, select an option, and press <Enter>.
Modify the system parameter to reflect the options installed in your
system.
4. You may return to the Main Menu anytime be pressing <ESC>.
5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and
reboots the system, and “EXIT WITHOUT SAVING” ignores your changes
and exits the program.
12
Page 13
65DV BIOS
STANDARD CMOS SETUP
Standard CMOS Setup allows you to record some basic system hardware configuration and set the system clock and error handling. You only need to modify
the configuration values of this option when you change your system hardware
configuration or the configuration stored in the CMOS memory gets lost or
damaged.
Run the Standard CMOS Setup as follows:
1. Choose “ST ANDARD CMOS SETUP” from the Main Menu and a screen
with a list of options will appear.
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys.
ROM PCI/ISA BIOS (2A69KSNH)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Tue, Oct 19 1999
Time (hh:mm:ss) : 15 : 6 : 26
HARD DISK TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
Primary Master : Auto 0M 0 0 0 0 0 AUTO
Primary Slave : Auto 0M 0 0 0 0 0 AUTO
Secondary Master : Auto 0M 0 0 0 0 0 AUTO
Secondary Slave : Auto 0M 0 0 0 0 0 AUTO
Drive A : 1.44, 3.5 in.
Drive B : None
Video : EGA/VGA
Halt On : All Errors
Esc : Quit
F1 : Help
(Shift) F2 : Change Color
: Select Item
Base Memory : 640K
Extended Memory : 64512K
Other Memory : 384K
Total Memory : 65536K
PU/PD/+/- : Modify
13
Page 14
65DV BIOS
Date (mm:dd:yy)
Time (hh:mm:ss)
Primary (Secondary)
Master / Slave
Drive A / B
Video
Halt On
Set the current date and time.
This field records the specification for all non-SCSI Hard Disk
Drives installed in your system. Refer to the respective documentation on how to install the drives.
Set the field to the type(s) of Floppy Disk drive(s) installed in
your system.
The choice:
360KB, 5.25in.
1.2MB, 5.25in.
720KB, 3.5in.
1.44MB, 3.5in.
2.88MB, 3.5in.
Set the field to the type of video display card installed in your
system.
The choice:
Monochrome,
Color 40x25,
EGA / VGA, (default)
Color 80x25
Set this warning feature for the type of errors that will cause
the system to halt.
The choice:
All Errors, (defaults)
No Errors,
All But Keyboard,
All But Diskette,
All But Disk / Key
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
14
Page 15
65DV BIOS
BIOS FEATURES SETUP
BIOS Features Setup allows you to improve your system performance or set
up system features according to your preference.
Run the BIOS Features Setup as follows:
1. Choose “BIOS FEATURES SETUP” from the Main Menu and a screen
with a list of options will appear.
ROM PCI/ISA BIOS (2A6LGSNC)
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning : Disabled
CPU Internal Cache : Enabled
External Cache : Enabled
CPU L2 Cache ECC Checking : Enabled
Processor Number Feature : Disabled
Quick Power On Self Test : Enabled
Boot Sequence : A,C,SCSI
Swap Floppy Drive : Disabled
Boot Up Floppy Seek : Disabled
Boot Up NumLock Status : On
IDE HDD Block Mode : Enabled
Gate A20 Option : Fast
Memory Parity/ECC Check : Disabled
Typematic Rate Setting : Disabled
Typematic Rate (Chars/Sec) : 6
Typematic Delay (Msec) : 250
Security Option : Setup
PCI/VGA Palette Snoop : Disabled
OS Select For DRAM > 64MB : Non-OS2
Video BIOS Shadow : Enabled
C8000-CBFFF Shadow : Disabled
CC000-CFFFF Shadow : Disabled
D0000-D3FFF Shadow : Disabled
D4000-D7FFF Shadow : Disabled
D8000-DBFFF Shadow : Disabled
DC000-DFFFF Shadow : Disabled
ESC : Quit
F1 : Help
F5 : Old Value
F7 : Load Setup Defaults
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys. An explanation of the
<F>keys follows:
<F1>: “Help” gives options available for each item.
<Shift> + <F2>: Change BIOS screen color.
<F5>: Get the previous values. These values are the values with the
user started in the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.
15
Page 16
65DV BIOS
Virus Warning
CPU Internal Cache
External Cache
CPU L2 Cache ECC
Checking
Processor Number
Feature
Enabled: Activates automatically when the system boots up
causing a warning message to appear if there is
anything attempting to access the boot sector or
Hard Disk partition table.
Disabled: No warning message will appear when there is
something attempting to access the boot sector or
Hard Disk partition table.
Note: Many diagnostic (or boot manager) programs which
attempt to access the boot sector table can cause
the above warning message. If you will be running
such a program, we recommend that you disable the
virus protection first.
Choose Enabled (default) or Disabled. This option allows user
to enable or disable the CPU internal cache.
Choose Enabled (default) or Disabled. This option allows user
to enable or disable the external cache memory.
Choose Enabled (default) or Disabled.
Choose Enabled or Disabled (default).
Quick Power On Self
Boot Sequence
Swap Floppy Drive
16
Choose Enabled (default) or Disabled. This option allows user
to speed up the Power-On-Self-T est routine.
Test
Default is “A , C, SCSI”. This option determines which drive
to boot at first for an operating system.
Default is “A, C, SCSI”. This option determines which drive
to boot at first for an operating system.
Page 17
65DV BIOS
Note: Some older model HDDs do not provide this feature.
Boot Up Floppy Seek
Boot Up NumLock
Status
IDE HDD Block Mode
Gate A20 Option
Memory Parity / ECC
Check
Typematic Rate Setting
Enabled (default): During POST, BIOS checks the track num-
ber for Floppy Disk drive to see whether it’s 40 or
80 tracks.
Disabled: During POST, BIOS will not check the track num-
ber for Floppy Disk drive.
On (default): Activate the NumLock function at boot up.
Off: Close the NumLock function at boot up.
Choose Enabled (default) or Disabled. If your hard disk is
larger than 540MB, choose Enabled. If you are using IDE
HDD AUTO DETECTION option, then BIOS will choose this
option automatically.
Choose Normal or Fast (default): This option allows the RAM
to access the memory above 1MB by using the fast gate A20
line.
Choose Enabled or Disabled (default).
Choose Enabled or Disabled (default): Enable this option to
adjust the deystroke repeat rate.
Typematic Rate
(Char / Sec)
Typematic Delay (Msec)
Range between 6 (default) and 30 characters per second.
This option controls the speed of repeating keystrokes.
Choose 250 (default), 500, 750 and 1000. This option sets
the time interval for displaying the first and the second
characters.
Security Option
Choose System or Setup (default). This option prevents unauthorized system boot up or use of BIOS Setup.
17
Page 18
65DV BIOS
PCI / VGA Palette
Snoop
OS Select for DRAM >
64MB
Video BIOS Shadow
C8000-CBFFF to DC000-
DFFFF Shadow
Choose Enabled or Disabled (default). It determines whether
or not the MPEG ISA cards can work with PCI / AGP.
Non-OS2 (default): For Non-OS/2 operating system.
OS: For OS/2 operating system.
Enabled (default): Map the VGA BIOS to system RAM.
Disabled: Don’t map the VGA BIOS to system RAM.
These options are used to shadow other expansion card
ROMs.
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
18
Page 19
65DV BIOS
CHIPSET FEATURES SETUP
Chipset Features Setup changes the values of the chipset registers. These
registers control the system options.
Run the Chipset Features Setup as follows:
1. Choose “CHIPSET FEATURES SETUP” from the Main Menu and a
screen with a list of options will appear.
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys.
ROM PCI/ISA BIOS (2A6LGSNC)
CHIPSET FEATURES SETUP
AWARD SOFTWARE, INC.
Bank 0/1 DRAM Timing : SDRAM 10ns
Bank 2/3 DRAM Timing : SDRAM 10ns
Bank 4/5 DRAM Timing : SDRAM 10ns
SDRAM Cycle Length : 3
DRAM Clock : Host CLK
Memory Hole : Disabled
Read Around Write : Enabled
Concurrent PCI/Host : Disabled
System BIOS Cacheable : Disabled
Video RAM Cacheable : Disabled
AGP Aperture Size : 64M
AGP-2X Mode : Disabled
OnChip USB1 : Enabled
OnChip USB2 : Enabled
USB Keyboard Support : Disabled
OnChip Sound : Enabled
OnChip Modem : Disabled
ESC : Quit
F1 : Help
F5 : Old Value
F7 : Load Setup Defaults
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
19
Page 20
65DV BIOS
Bank 0/1 2/3 4/5 DRAM
Timing
SDRAM Cycle Length
DRAM CLOCK
Memory Hole
Read Around Write
This item allows you to select the value in this field, depending on whether the board has paged DRAMs or EDO
(extended data output) DRAMs.
The choice:
EDO 50ns,
EDO 60ns,
Slow,
Medium,
Fast,
Turbo
Y ou can select CAS latency time in HCLKs of 2/2 or 3/3. The
system board designer should have set the values in this field,
depending on the DRAM installed. Do not change the values
in this field unless you change specifications of the installed
DRAM or the installed CPU.
The setting of this item must depend on the spec of PC100/
PC133. For example, if user chooses HCLK + 33M, that
means not only the motherboard but also the SDRAM needs
to comply with PC-133 spec.
Choice: Host CLK(default), HCLK-33M or HCLK+33M.
Choose Enabled or Disabled (default). In order to improve
performance, certain space in memory can be reserved for
ISA cards. This memory must be mapped into the memory’s
space below 16MB.
DRAM optimization feature: If a memory read is addressed to
a location whose latest write is being held in a buffer before
being written to memory, the read is satisfied through the buf fer
contents, and the read is not sent to the DRAM.
The choice:
Enabled,
Disabled
Concurrent PCI / Host
System BIOS
Cacheable
20
When disabled, CPU bus will be occupied during the entire
PCI operation period.
The choice:
Enabled,
Disabled
Choose Enabled or Disabled (default). When Enabled, the
access to the system BIOS ROM addressed at F0000HFFFFFH is cached.
Page 21
65DV BIOS
Video RAM Cacheable
AGP Aperture Size (MB)
AGP-2X Mode
OnChip USB1
OnChip USB2
USB Keyboard Support
Choose Enabled or Disabled (default). When enabled, the
access to the VGA RAM addressed is cached.
Choose 4, 8, 16, 32, 64 (default), 128 or 256MB. Memory
map and graphics data structures can reside in a Graphics
Aperture. This area is like a linear buffer. BIOS will automatically report the starting address of this buffer to the O.S.
This item allows user to enable / disable the AGP-2x (133MHz
clock) mode.
This should be enabled if your system has a USB installed on
the system board and you wish to use it. Even when so
equipped, if you add a higher performance controller, you will
need to disable this feature.
The choice:
Enabled (default), Disabled
This should be enabled if your system has a USB installed on
the system board and you wish to use it. Even when so
equipped, if you add a higher performance controller, you will
need to disable this feature.
The choice:
Enabled (default), Disabled
Enabled: Enables function when the USB keyboard is being
used.
Disabled (default): When the AT keboard is being used.
OnChip Sound
OnChip Modem
Enabled (default): Turn on AC’97 Codec chip controller .
Disabled: Turn off AC’97 Codec chip controller . If user wants
to use external sound card, this function must be disabled.
Enabled (default): Use MC99 feature.
Disabled: Turn off MC99 feature. If user wants to use external modem, this function must be disabled.
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
21
Page 22
65DV BIOS
POWER MANAGEMENT SETUP
Power Management Setup changes the system power savings function.
Run the Power Management Setup as follows:
1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a
screen with a list of options will appear.
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys.
ROM PCI/ISA BIOS (2A6LJSN9)
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
ACPI function : Disabled
Power Management : User Define
PM Control by APM : Yes
Video Off After : Suspend
Video Off Method : V/H SYNC+Blank
MODEM Use IRQ : 3
Soft-Off by PWRBTN : Instant-Off
PWRON After PW-Fail : Former-Sts
HDD Power Down : Disabled
Doze Mode : Disabled
Suspend Mode : Disabled
** PM Events **
VGA : OFF
LPT & COM : LPT/COM
HDD & FDD : ON
PCI Master : OFF
Modem Ring Resume : Disabled
RTC Alarm Resume : Disabled
Primary INTR : ON
IRQ3 (COM 2) : Primary
IRQ4 (COM 1) : Primary
IRQ5 (LPT 2) : Primary
IRQ6 (Floppy Disk) : Primary
IRQ7 (LTP 1) : Primary
IRQ8 (RTC Alarm) : Disabled
IRQ9 (IRQ2 Redir) : Secondary
IRQ10 (Reserved) : Secondary
IRQ11 (Reserved) : Secondary
IRQ12 (PS/2 Mouse) : Primary
IRQ13 (Coprpcessor) : Primary
IRQ14 (Hard Disk) : Primary
IRQ15 (Reserved) : Disabled
ESC : Quit
F1 : Help
F5 : Old Value
F7 : Load Setup Defaults
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
22
Page 23
65DV BIOS
Note: This function must work with JP8.
ACPI Function
Power Management
PM Control By APM
Video Off After
Video Off Method
Modem Use IRQ
Soft-Off By PWR-BTTN
Enabled: Turn on ACPI function.
Disabled (default): Turn off ACPI function.
Choose Max. Saving, User Define (default), Disabled, or Min.
Saving.
Choose Y es (default) or No. You need to choose Yes when
the operating system has the APM functions, otherwise
choose No.
Choose NA, Suspend, Standby (default) or Doze.
Choose Blank, DPMS or V/H Sync+Blank (default). Y ou can
choose either DPMS or V/H Sync+Blank when ther monitor
has the Green function. Y ou need to choose Blank when the
monitor has neither the Green function.
Assign the IRQ number to the modem which is being used so
that the ring signal can wake up the system. The default setting is 3 (COM2).
Instant-Off (default): Turn of f the system power at once after
pushing the power button.
Delay 4 Sec: Turn off the system power 4 seconds after push-
ing the power button (to meet PC97/98 spec)
PWRON After PW-Fail
HDD Power Down
Choose Off (default), On, Former Sts.
Off: Disable Power Lost Resume function.
On: Enable Power Lost Resume function.
Former Sts.: Use former status.
Time is adjustable from 1 to 15 minutes. When the set time
has elapsed, the BIOS sends a command to the HDD to power
down which turns off the motor.
23
Page 24
65DV BIOS
Doze Mode
Suspend Mode
VGA
LPT & COM
HDD & FDD
This mode sets the CPU speed down to 33MHz.
The option allows you to choose the mode for the different
timer. The Suspend mode turns off the CPU and saves the
energy of the system.
When On of VGA, any activity from one of the listed system
peripheral devices or IRQs wakes up the system.
Choice: On(default), Off.
When On of LPT&COM, any activity from one of the listed
system peripheral devices or IRQs wakes up the system.
Choice: LPT/COM(default), NONE, LPT or COM.
When On of HDD&FDD, any activity from one of the listed
system peripheral devices wakes up the system.
Choice: On(default), Off.
DMA / master
Modem Ring Resume
RTC Alarm Rescume
24
When On, any activity from one of the listed system peripheral devices wakes up the system.
Choice: On, Off(default).
An input signal on the serial Ring Indicator (RI) Line (in other
words, an incoming call on the modem) awakens the system
from a soft off state.
When Enabled, you can set the date and time at the which
the RTC(Real Time Clock) alarm awakens the system from
suspend mode.
Choice: Disabled(default), Enabled.
Page 25
65DV BIOS
Primary INTR
The following is a list of IRQ’s(Interrupt ReQuests), which can be exempted much as the
COM ports and LPT ports above can. When an I/O device wants to gain the attention of the
operating system, it signals this by causing an IRQ to occur. When the operating system is
ready to respond to the request, it interrupts itself and performs the service.
When set On, activity will neither prevent the system from going into a power management
mode nor awaken it.
IRQ3 (COM2)
IRQ4 (COM1)
IRQ5 (LPT2)
IRQ6 (Floppy Disk)
IRQ7 (LPT1)
IRQ8 (RTC Alarm)
When set to On, any event occurring at will awaken a system
which has been powered down.
On(default): The system can not enter the power saving mode
when I/O ports or IRQ# is activated.
Off: The system still can enter the power saving mode when
I/O ports or IRQ# is activated.
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
25
Page 26
65DV BIOS
PnP/PCI CONFIGURA TION SETUP
PnP/PCI Configuration Setup defines PCI bus slots.
Run the PnP/PCI Configuration Setup as follows:
1. Choose “PnP/PCI CONFIGURATION SETUP” from the Main Menu and
a screen with a list of options will appear.
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys.
ROM PCI/ISA BIOS (2A6LGSNC)
PNP/PCI CONFIGURATION
AWARD SOFTWARE, INC.
PNP OS Installed : No
Resources Controlled By : Auto
Reset Configuration Data : Disabled
CPU to PCI Write Buffer : Enabled
PCI Dynamic Bursting : Enabled
PCI Master 0 WS Write : Enabled
PCI Delay Transaction : Enabled
PCI#2 Access #1 Retry : Disabled
AGP Master 1 WS Write : Disabled
AGP Master 1 WS Read : Disabled
Assign IRQ For USB : Enabled
Assign IRQ For VGA : Enabled
ESC : Quit
F1 : Help
F5 : Old Value
F7 : Load Setup Defaults
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
26
Page 27
65DV BIOS
Note: BIOS will automatically diable all PnP resources
except the boot device card when you select Yes on
Non-PnP O.S.
PNP OS Installed
Resources Controlled
By
Reset Configuration
Data
CPU to PCI Write Buffer
PCI Dynamic Bursting
PCI Master 0 WS Write
Y es: OS supportsss Plug and Play function.
No (default): OS doesn’t support Plug and Play function.
Choose Manual (default) or Auto. The BIOS checks the IRQ/
DMA channel number on the ISA and PCI card manually if
you choose Manual. And the IRQ/DMA channel number will
be checked automatically if you choose Auto.
Choose Enabled or Disabled (default). Disable retains Enabled PnP configuration data in BIOS and resets the PnP
configuration data in the BIOS.
Choose Enabled(default) or Disabled.
Choose Enabled(default) or Disabled .
Choose Enabled(default) or Disabled .
PCI Delay Transaction
PCI #2 Access #1 Retry
AGP Master 1 WS Write
AGP Master 1 WS Read
Choose Enabled(default) or Disabled .
Choose Enabled or Disabled(default).
Choose Enabled(default) or Disabled.
Choose Enabled or Disabled(default).
27
Page 28
65DV BIOS
Assign IRQ for USB
Assign IRQ for VGA
Enabled (default): Add one IRQ to USB controller.
Disabled: Remove IRQ from USB controller. The system will
have extra IRQ for other devices but the USB controller will still not be diabled (only IRQ was
removed)
Enabled (default): Add one IRQ to VGA controller.
Disabled: Remove IRQ from VGA controller. The system will
have extra IRQ for other devices but the VGA controller will still not be disabled (only IRQ will be
removed)
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
28
Page 29
65DV BIOS
LOAD SETUP DEFAULTS
Load Setup Defaults option loads the default system values to the system
configuration fields. If the CMOS is corrupted the defaults are loaded
automatically.
Choose this option and the following message will appear:
“Load Setup Defaults (Y/N)? N”
To use the Setup Defaults, change the prompt to “Y” and press <Enter>.
29
Page 30
65DV BIOS
CPU SPEED SETTING
CPU Speed Setting option allows user to adjust CPU’s settings and retain
some informations inside computer when it is working.
Run the Integrated Peripherals as follows:
1. Choose “CPU SPEED SETTING” from the Main Menu and a screen with
a list of options will appear.
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys.
ROM PCI/ISA BIOS (2A6LGSNC)
CPU SPEED SETUP
AWARD SOFTWARE, INC.
Auto Detect DIMM/PCI Clk : Disabled
Spread Spectrum : Disabled
CPU Host Clock(CPU/PCI) : Default
Current CPU Temp. :
Current System Temp. :
Current CPUFAN1 Speed :
Current CPUFAN2 Speed :
Vcore : 2.5V :
3.3V : 5V :
12V :
30
ESC : Quit
F1 : Help
F5 : Old Value
F7 : Load Setup Defaults
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
Page 31
65DV BIOS
Auto Detect DIMM/PCI
clk
Spread Spectrum
CPU Host Clock (CPU/
PCI)
Current CPU Temp.
Current System Temp.
Current CPUFAN1
Speed
Choose Disabled (default) or Enabled. The clock generator
will turn off the DIMM clock if this slot is empty .
Choose Disabled (default) or Enabled. This function is designed to EMI test only.
Select the CPU Host Clock.
The choice: default, 66/33MHz, 75/37MHz, 83/41MHz, 124/
31MHz, 133/33MHz, 140/35MHz, 150/37MHz.
Shows temperature of the CPU.
Shows the temperature of the system.
Shows current speed of the FAN. The fan must provide rotary pulse. (Normally these types of fan have a three-wire
connector.)
Current CPUFAN2
Speed
Voltage
Shows current speed of the FAN. The fan must provide rotary pulse. (Normally these types of fan have a three-wire
connector.)
Shows power supply actual voltage value.
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
31
Page 32
65DV BIOS
INTEGRA TED PERIPHERALS
Integrated Peripherals option changes the values of the chipset registers. These
registers control system options in the computer.
Run the Integrated Peripherals as follows:
1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a
screen with a list of options will appear.
2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp/PgDn/+/- keys.
ROM PCI/ISA BIOS (2A6LGSNC)
INTEGRATED PERPHERALS
AWARD SOFTWARE, INC.
OnChip IDE Channel0 : Enabled
OnChip IDE Channel1 : Enabled
IDE Prefetch Mode : Enabled
Primary Master PIO : Auto
Primary Slave PIO : Auto
Secondary Master PIO : Auto
Secondary Slave PIO : Auto
Primary Master UDMA : Auto
Primary Slave UDMA : Auto
Secondary MasterUDMA : Auto
Secondary Slave UDMA : Auto
Init Display First : PCI Slot
Onboard FDD Controller : Enabled
Onboard Serial Port 1 : 3F8/IRQ4
Onboard Serial Port 2 : 2F8/IRQ3
UART 2 Mode : Standard
IR Function Duplex : Half
TX, RX inverting enable : No, Yes
Onboard Parallel Port : 378/IRQ7
Onboard Parallel Mode : ECP/EPP
ECP Mode Use DMA : 3
Onboard Legacy Audio : Enabled
Sound Blaster : Disabled
SB I/O base Address : 220H
SB IRQ Select : IRQ 5
SB DMA Select : DMA 1
MPU-401 : Disabled
MPU-401 I/O Address : 330H - 333H
Game Port(200H - 207H) : Enabled
ESC : Quit
F1 : Help
F5 : Old Value
F7 : Load Setup Defaults
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
32
Page 33
65DV BIOS
OnChip IDE Channel
0 / 1
IDE Prefetch Mode
Primary
Master/Slave PIO
Secondary
Master/Slave PIO
Primary Master/Slave
UDMA
Secondary Master/Slave
UDMA
Init Display First
The chipset contains a PCI IDE interface with support from
two IDE channels. Select Enabled to activate the first and/or
the second IDE interface. Select Disabled to deactivate an
interface, if you install a primary and/or second add-on IDE
interface.
The choice: Enabled(default), Disabled.
Choose Enable(default), Disabled.
Choose Auto (default) or Mode 0~4. The BIOS will detect the
HDD mode type automatically when you choose Auto. Y ou
need to set to a lower mode than Auto when your hard disk
becomes unstable.
Enabled (default): Turn on the onboard IDE function.
Disabled: Turn off the onboard IDE function.
This option allows you to decide to activate PCI Slot or AGP
first.
Choose PCI Slot(default), AGP.
Onboard FDC
Controller
Onboard Serial Port1
Onboard Serial Port2
Choose Enabled (default) or Disabled. Choose Disabled when
you use an ISA card with FDD function, or choose Enabled to
use the onboard FDD connector.
Choose Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/
IRQ3 or Disabled. Don’t set port 1 & 2 to the same value,
except when setting at Disabled.
Choose Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/
IRQ3 or Disabled.
33
Page 34
65DV BIOS
Note: This option will not be displayed unless the EPP/
ECP is selected.
Note: The above 2 options will not be displayed unless the
EPP/ECP is selected.
Note: The above 2 options won’t work unless UART2
Mode HPSIR/ASKIR is selected.
UART 2 Mode
IR Function Duplex
TX, RX inverting
enabled
Onboard Paralle Port
Onboard Parallel Mode
ECP Mode Use DMA
Choose Standard (default), HPSIR or ASKIR.
The choice: Half (default), Full
Choose No, Y es (default) / No, No / Yes, No / Yes, Y es.
Choose the printer I/O address: 378H/IRQ7 (default), 3BCH/
IRQ7, 278H/IRQ5 or Disabled.
Choose Normal (default), ECP/EPP, SPP mode. The mode
depends on the external device connected to this port.
Choose DMA3 (default) or DMA1. Most sound cards use
DMA1. Check with your sound card configuration to make
sure that there is no conflict with this function.
EPP Mode Select
Choose EPP1.7 (default) or EPP1.9. EPP1.9 supports hardware handshake. This setting is dependent upon your EPP
device.
Onboard Legacy Audio
The choice: Enabled (default), Disabled.
34
Page 35
65DV BIOS
Sound Blaster
SB I/O Base Address
SB IRQ Select
SB DMA Select
MPU-401
MPU-401 I/O Address
Game Port (200-207H)
Choose Enabled or Disabled (default). For DOS mode
compatibility, this option must be enabled. In Windows system,
this option must be disabled.
Use default setting.
Use default setting.
Use default setting.
Choose Enabled or Disabled (default). Some feedback type
joystick must enable this option (ex: Sidewinder joystick).
Use default setting.
Use default setting.
3. Press <ESC> and follow the screen instructions to save or disregard
your setting.
35
Page 36
65DV BIOS
Note: If you forget or lose the password, the only way to
access the system is to clear the CMOS RAM by
setting JBAT1. All setup information will be lost and
back to default seting. You need to run the BIOS
setup program and re-define all settings again.
SUPERVISOR/USER P ASSWORD
These two options allow you to set your system passwords. Normally, the
supervisor has a higher ability to change the CMOS setup option than the user.
The way to set up the passwords for both supervisor and user are as follows:
1. Choose “CHANGE PASSWORD” from the Main Menu and press
<Enter>. The following message appears:
Enter Password:
2. The first time you run this option, enter your own password up to 8
characters and press <Enter>. The screen doesn’t display the
entered characters.
3. After you entered the password, the following message appears
prompting you to confirm the password:
Confirm Password:
4. Enter the same password “exactly” as you just typed again to
confirm the password and press <Enter>.
5. Move the cursor to Save & Exit Setup to save the password.
6. If you need to delete the password you entered before, choose the
Supervisor Password and press <Enter>. It will delete the password
that you had before.
7. Move the cursor to Save & Exit Setup to save the option you did,
otherwise the old password will still be there the next time you turn
your machine on.
8. Press <ESC> to exit to the Main Menu.
36
Page 37
65DV BIOS
IDE HDD AUTO DETECTION
IDE HDD Auto Detection detects the parameters of an IDE Hard Disk drive and
automatically enters them to the Standard CMOS Setup screen.
The screen will ask you to select a specific Hard Disk for Primary Master
after you selected this option. If you accept a Hard Disk detected by the
BIOS, you can enter “Y” to confirm and then press <Enter> to check next
Hard Disk. This function allows you to check four Hard Disks and you
may press the <ESC> after the <Enter> to skip this function and go back
to the Main Menu.
SAVE & EXIT SETUP
Save & Exit Setup allows you to save all modifications you have specified into
the CMOS memory. Highlight this option on the Main Menu and the following
message appears:
SAVE to CMOS and EXIT (Y/N)? Y
Press <Enter> key to save the configuration changes.
EXIT WITHOUT SAVING
Exit Without Saving allows you to exit the Setup utility without saving the modifications that you have specified. Highlight this option on the Main Menu and
following message appears:
Quit Without Saving (Y/N)? N
You may change the prompt to “Y” and press the <Enter> key to leave this
option.
37
Page 38
Appendix A
APPENDIX A
FLASH MEMORY UPDATE INSTALLATION
1. Download BIOS files and flash utility from your board vendor. They are:
awdflash.exe and .bin file.
2. Copy them to bootable diskette and boot from diskette.
3. The diskette cannot include memory manager e.g. emm386.exe,qemm and
himem.sys, otherwise there will appear an error message “insufficient memory”.
4. Type “awdflash filename(XXXX.bin)”.
5. Next screen will ask you save current bios to file or not? Depend on your
diskette capacity, choose Y or N for this option.
6. Then screen ask you programming the flash memory now? type Y for this
option.
7. Programming finish,utility will ask you reboot system.
8. Reset system and press DEL key enter bios setup screen.
9. Select LOAD SETUP DEFAULTS, press ENTER, press Y, press F10, press Y
10. Finish update procedure.
38
Page 39
Appendix B
APPENDIX B DRIVER INSTALLATION
If you are using Windows 98 SE, you do not need to install the 4-in-1
driver as the IRQ Routing Driver and the ACPI Registry are already incorporated into the operating system. Users with Windows 98 SE may update the
IDE Busmaster and AGP drivers by installing them individually.
PART 1:
1. Put the CD into your CD-ROM.
2. There appears a welcome window.
(If doesn’t, it means that your CD-ROM auto-run function does not enable, but
you still can browser the CD via Windows Explorer and change the directory to
where your CD-ROM directory is. Then run the autorun.exe)
3. Select “Install Driver”.
4. Select “Install VIA Chipsets Driver”.
5. Select “Install 4in1 Driver”.
6. Then the program will automatically setup all drivers your system needs.
7. Finally, the system will re-boot.
NOTE: AFTER INSTALLED “ 4in1 Driver”, USER DOESN’T NEED TO INSTALL ANY
OTHER PROGRAM IN PART 2.
PART 2:
CAUTION!! ALL THE VIA MAINBOARD MUST INSTALL FOLLOWING 3 DRIVERS!!!
VIA Patch Code Installation
Windows95/Windows98:
1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\.
2. Find and run D:\Patch\Via\patch9x\Setup\Setup.exe
3. Select “Install VIA Chipset Functions’ Registry”, then it will automatically
install this program.
Note! This program should be installed before any other VIA’s drivers.
VIA AGP VxD Driver for Windows 9x Installation
Windows95/Windows98:
1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\.
2. Find and run D:\Driver\Via\Agp\Setup\Setup.exe
3. Select “Install VIA AGP VxD in turbo mode” or “Install VIA AGP VxD normal
mode”, then it will automatically install this program.
39
Page 40
Appendix B
VIA PCI IRQ Routing Miniport for Windows 9x Installation
Windows95/Windows98:
1. Go to the CD-ROM disk, we suggest the CD-ROM title is D:\.
2. Find and run D:\Patch\Via\Virq9x\Setup.exe
Note: Before install Windows98, user must enable two functions for this miniport driver
in the BIOS menu, one is “OnChip USB” in the “Chipset Features Setup” and
another is “Assign IRQ for USB” in the “PNP/PCI Configuration Setup”.
40
Page 41
Appendix C
APPENDIX C THE USAGE OF RT2
Thermal Sensor Connector
a: Connect to RT2.
b: Connect this thermal sensor to
particular device which generates lots of heat such as Hard
Disk, VGA chip, etc. When
connected, user could observe
the temperature change from
the BIOS program.
VIA Hardware Monitor Setup
1. Make sure that the CD is in the CD-ROM.
2. There will appear a welcome window, please use the mouse to choose
“Install Driver” item.
(If not, that means user’s CD-ROM autorun function is disabled, but user
could still install the program via Windows Explorer. )
3. Choose “Install VIA Chipset Driver” item, then choose “Install VIA
Hardware Monitor” item.
4. The setup program will install Hardware Monitor software automatically.
41
Loading...