User's Guide
SP7-100
User's Guide
■ Thank you for purchasing Solt wireless calling system products.
■ Please read this user's guide carefully before using and follow the instructions.
■ Specification and instructions are subject to change without notice.
Important Safety Instructions
Contents / Recharging Instructions
Name of each part / Screen Layout (Idle screen)
Screen Layout (Receiving Screen / Cancel receiving screen )
List of setting modes
Time Setting
..............................................................................
Sound / Vibration Setting
Bell ID Setting
(1) New bell ID registration
(2) Calling number change
(3) Whole calling number deletion
Other Settings
(1) STAT : Checking the detail set by Other Settings
(2) CONT : Adjusting the contrast of LCD screen
(3) DUPT : Duplicated receiving prevention time
(4) SOND : Number of call alarm repetition
(5) COPY : Registration transmission
(6) NORX : Receiving restriction number
(7) RSSI : Receiving sensitivity check
(8) REMD : Unchecked calling number notification
.............................................................
....................................................
.................................
......................................................................
.............................................................
......................................
......................................
............................
........................
...................
.......................
...............
.......
.........
................
......
...
3
4
5
6
7
8
9
10~11
12
13
14
15
16
17
18~19
20
21
22
Important Safety Instructions
Safety Instruction contains the information to prevent the unexpected risk or damage in
advance by using the product in correct way and it should always be observed all the times.
Warning
Caution
Power precautions
Be sure to insert the power plug to
the end of the inner part.
[If the connection is unstable, it may
cause fire.]
Do not use one socket for multiple
devices at the same time. [It may cause
fire due to overheating of the socket.]
This is for the case with the possibility of serious injury or death if this is not observed.
This is for the case with the possibility of minor injury or damage to the product
if this is not observed.
Warning
Warning
Be sure to unplug the power plug while
holding it firmly. If cord is unplugged
by pulling out, some parts of the cord
can be disconnected and it may cause
risky situation. [
If power plug is dropped or case is
broken, unplug the power cord. [If it is
used as it is, it may cause fire or
tric shock. Please contact service center.]
It may cause fire.
Caution
]
Caution
elec-
Caution
Do not touch the power plug with wet hand.
[There is a risk of electric shock.]
Caution
In case of thunderstorm or lighting or
if the power plug is not used for long
time, unplug the power cord. [There
is the risk of electric shock or fire.]
Caution
Specification
Model SP7-100
Frequency (MHz) 433.0500 ~ 434.7900
Freq Stability ±5 ppm
Data Rate 1800 bps
Channel space 12.5 KHz
Modulation FSK (±3KHz)
Sensitivity -118dBm (at Direct)
Power Supply DC 3.7V/250mA Li-Polymer Battery (Rechargeable)
Dimension (mm) 37W × 49L × 13.5H
Standby Time about 30 hours
Antenna Helical (Internal)
Use precautions
Do not harm or damage the unit with
sharp object such as nail, pencil, or pen.
[It will damage the surface of the unit
and cause malfunction.]
Do not disassemble or modify the
unit. If repair of the unit is required,
please contact the service center.
Warning
CautionCaution
Do not clean the unit with water,
benzene or paint thinner.
[Damage to the insulation of electrical
parts may cause malfunction.]
Battery charging level.
Caution
When the battery icon indicates as
marked in a circle, use it after
recharging for more than 2 hours.
If foreign object enters the unit,
please contact service center.
[This may cause damage to the
internal parts.]
Caution
Use the supplied adapter.
[Malfunctioning of supplied adapter
during its use is not covered by
manufactures' warranty.]
3
Contents
[Main Body] [Adapter - DC5V 1A][Wrist Band]
PRGH
VHW
SZU
Upper Band
Input : 100-240V~50/60Hz
Onput : DC5V 1A
[Charging cables - micro USB]
Name of each part
Push the band to the left fitting into the groove of main body.)
Buttons Description
MODE
Press it more
than 2 seconds
Press it more
SET
than 2 seconds
Press it more
PWR
than 2 seconds
<
Press it
<
once shortly
Press it
SET
once shortly
Entering into Mode / Exit to idle screen
Conversion of numbers, English letters and special characters
Move to upper mode
Power ON/OFF
Mode Shift, Digit Location Shift, Shift to receiving screen
Mode Selection, Setting Value Selection and Change
(How to combine main body and band :
Wrist type upper band
Wrist type lower band
PRGH
←
←
←
VHW
SZU
Lower Band
Screen Layout
Idle screen
Recharging Instructions
※ Please use only supplied adaptor.
Reception
available
AM/PM
Defect of the product caused by the use of other products will be repaired with charge.
Limited accessary warranty. Malfunctioning of supplied adapter during its use is not
covered by manufactures' warranty.
① Open the USB cover of pager.
② Connect micro USB jack to the connector of pager.
③
②
①
4 5
③ Plug the cord into the outlet after connecting
adaptor and USB cable.
Battery charging level.
When the battery icon indicates as marked
in a circle, use it after recharging for more
than 2 hours.
Current Time
Unchecked call Icon, Number of Unchecked Calls
Sound
Vibration
Remaining
battery
Charging in progress battery icon
Charging completed battery icon
※ When there are unchecked calling numbers in idle screen,
the number of unchecked calls is displayed.
When you press SET button at receiving screen,
unchecked call icon is disappeared. When you
check all received call numbers, only current time
is displayed.
Screen Layout
List of setting modes
Receiving Screen : Screen example of receiving number [A11]
Current Time
Receiving
number
Unchecked
call Icon
Receiving time
Receiving sequence / Total number of calls
· [A11] calling number is displayed in the middle, and receiving time is displayed at left bottom.
·
Tot al n um be r of re c ei ve d ca ll s a nd re ce iv ing s eq ue nc e o f ca ll in g numbers are displayed at right bottom.
[A11] is secondly received number out of total 3 receiving numbers.
· Total 50 calling numbers can be stored.
(When 51st calling number is received, 1st receiving calling number is disappeared.)
▶
When you press SET button,
unchecked call icon is disappeared.
Cancel receiving screen : Example screen of [A11] cancellation among receiving numbers
You can set following listed modes using set button of main body.
Time Setting
Sound / Vibration Setting
ㆍ24hours digital watch function
ㆍCall notification method setting
ㆍNew bell ID registration
Bell ID Setting
ㆍCalling number change
ㆍWhole calling number deletion
(1) STAT : Checking the detail set by Other Settings
(2) CONT : Adjusting the contrast of LCD screen
(3) DUPT : Duplicated receiving prevention time
SOND
Other Settings
(4)
(5) COPY : Registration transmission
(6) NORX : Receiving restriction number
(7)
(8)
: Number of call alarm repetition
RSSI
: Receiving sensitivity check
REMD
: Unchecked calling number notification
Entering into Setting Mode
You can enter into setting mode by pressing
MODE button for more than 2 seconds at idle screen.
Setting mode screen
※ Note: Calling signal cannot be received at setting mode.
(Calling signal can be received at idle screen only.)
▶
Receiving
number
Cancel Button of [A11]
OK Icon
·[A11] is displayed together with OK icon at right bottom.
·After cancellation, [A11] is deleted from receiving list, and total number of calls is
decreased.
6 7
Exit from setting mode to idle screen
If you press MODE button at setting mode screen for
more than 2 seconds, Idle screen is displayed.
Current Time
Idle screen
Time Setting
You can set the time of Pager.
Sound / Vibration Setting
You can set sound or vibration when receiving calls.
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Select 'Hour' using SET button and
after setting 'Hour' using arrow keys,
press SET button.
④ Move cursor using arrow keys and
select 'Minute' using SET button.
⑤
After setting 'Minute' using arrow keys,
press SET button.
⑥ When you press SET button for more than 2 seconds,
setting is completed.
▶
▶
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ If you select Type using arrow keys, you can check
sound or vibration.
④
When you press SET button for more than 2 seconds
after selecting Type, setting is completed.
⑤
When you press MODE button for more than 2 seconds,
idle screen is displayed.
Sound Mode Only sound output is made and there are ① ② ③ types.
① ② ③
① ② ③
① ② ③
Vibration Mode
⑦ When you press MODE button for more than 2 seconds,
idle screen is displayed.
Note
※ If battery is completely discharged and goes out, set time can be initialized.
8 9
Sound/Vibration Mode
Note
※
Cancel reception notifying methods(sounds/vibrations) are fixed
depending on each [sound mode, vibration mode, sound/vibration mode].
Only vibration output is made and there are ① ② ③ types.
Sound and vibration outputs are made at the same time
and there are ① ② ③ types.
New bell ID registration
(1) New bell ID registration (Available number of calling bell registration: about 900)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Enter into Mode using SET button.
④ When calling bell that is to be registered as No.1 is pressed,
it is registered with 'beep' sound. Number of cursor location
is changed to '2', and when calling bell that is to be registered
as No.2 is pressed, it is registered.
Thus each time next calling bell is pressed in order, sequential
registration is made from No.1.
If you want to change to other characters, refer to following table.
(④-1)
When character inversion is made by pressing SET button, you can select
other characters using arrow keys.
[Character Inversion]
▶
Character
Change
When you press MODE button for more than 2 seconds, you can select
<Numbers, English Lower Case Letters, English Capital Letters, Special Characters>.
Registered total number of calling bells.
⑤ When you press SET button for more than 2 seconds,
registration is completed and returns to previous stage.
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑦
When you press MODE button for more than 2 seconds,
idle screen is displayed.
※ Expressible Characters
Numbers
English Letters
(Lower case letters)
English Letters
(Capital Letters)
Special Characters
Digit Loca-
tion Shift
(Cursor
Movement)
10 11
You can move cursor location using arrow keys.
(Blank)
Calling Number Change
Whole calling number deletion
(2) Calling Number Change (Mode that changes registered calling number)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow
keys and enter into change mode by
pressing SET button.
ㆍ'Press Bell' is displayed.
Example: Change [A1] to [C-5].
④ When you press calling bell that you want to change among
registered calling bells, relevant number is displayed with
'beep' sound.
⑤ After changing to desired characters, when you press SET button
for more than 2 seconds, changed number is stored and
'Press Bell' is displayed.
(Refer to 'New Calling Number Registration (④-1)' for character
change method.)
⑥
If you want to change other calling number, repeat ④~⑤ process.
Registered
number
Changed
number
⑦ When pressing SET button for more than 2 seconds,
it returns to previous stage.
(3) Whole calling number deletion (Mode that deletes all registered calling numbers)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into
change mode by pressing SET button.
④
If you want whole deletion, move to [YES] and press SET button.
If you want to cancel whole deletion, move to [NO] and press
SET button.
⑤ When you make whole deletion, registered all calling numbers
are deleted, therefore, you need to check one more time.
If you want whole deletion, move to [YES] and press SET button.
Registered total number of calling bells.
⑥ After 'beep' sound is made, whole deletion
is completed and returns to previous stage.
Number of registered calling bells becomes '0'.
⑧ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑨
When you press MODE button for more than 2 seconds,
idle screen is displayed.
12 13
⑦ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑧
idle screen is displayed.
Other Settings Other Settings
⑴ Checking the detail set by Other Settings
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
Total registered bells(32 bells) / Receiving-restricted bells(5 bells)
Number of call alarm repetition : call to be alarmed one(1) time
When receiving same calling numbers for 3 seconds, it is displayed only once.
Battery calibration value(Only for manufacturer's checking purpose)
④ When pressing SET button for more than 2 seconds,
it returns to previous stage.
(2) Adjusting the contrast of LCD screen
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
④
Set desired value using arrow keys. (default setting value is 10.)
You can select it from 00 to 20.
⑤ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑤ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑥
idle screen is displayed.
14 15
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑦
idle screen is displayed
Other Settings
Other Settings
⑶ Duplicated receiving prevention time
(When receiving same calling numbers, it allows only one
reception during set time period.)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
④
Set desired value using arrow keys.
Initial setting value is [03] and 3 seconds (setting range: 00~99).
(When receiving same calling numbers for 3 seconds, it is displayed
only once.)
⑤ When you press SET button for more than 2 seconds,
storing is completed and returns to previous stage.
⑷ Number of call alarm repetition
(It is a function that sets repeated numbers of sound or
vibration for calls.)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
④
Set desired value using arrow keys.
ㆍInitial setting value is [01] and it means one time notification against a call.
(setting range: 00~99)
ㆍ
When setting as [00], receiving notification is repeated continuously,
and when pressing any button, receiving notification stops.
⑤ When you press SET button for more than 2 seconds,
storing is completed and returns to previous stage.
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑦
idle screen is displayed.
16 17
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑦
idle screen is displayed.
Other Settings
⑸ Registration transmission
(Function that duplicates registered all calling numbers to
other pagers.)
ㆍConnect 2 pagers using dedicated cable.
(Transmission time varies depending on the registered capacity.)
④
When you press SET button, transmission starts, and when transmission is completed,
'OK' icon is displayed.
ⓐ
Pager screen that transmits data
...............................
SET Button. Transmission Start Being Transmitted Transmission Completion
ⓑ
Pager screen that receives data
(※ Data can be transmitted only in idle mode.)
Dedicated Data Transmission cable
Pager screen that transmits data
(Refer to following sequence.)
(Option item)
Pager screen that receives data
(The registered Bell IDs are deleted.)
: Data can be transmitted only in idle mode.
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
idle screen
Beep sound + Backlight turns on
Rebooting after completing
transmission
⑤ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑦
When you press MODE button for more than 2 seconds,
idle screen is displayed.
※ When the cable is not connected well or when the mode of a receiving pager is not idle one.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
SET Button.
Transmission Start
18 19
...............................
After 'WAIT' displayed for 15 seconds
"ERR" appears on the screen.
Mode moves to previous stage.
Other Settings
Other Settings
⑹ Receiving restriction number
(Function that sets unwanted receiving number out of
registered calling numbers.)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
④
After searching unwanted receiving number using arrow keys,
when you press SET button, it is set as no- reception [NoRx].
When you press SET button once again, it is set as reception [Rx].
(Initial setting value is reception [Rx].)
Pager does not receive call from [T-9].
⑤ When you press SET button for more than 2 seconds,
storing is completed and returns to previous stage.
⑺ Receiving sensitivity check
(Function that checks receiving signal strength.)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
④
When you press a calling bell, you can check receiving
signal strength.
⑤ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑦
idle screen is displayed.
20 21
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
⑦
When you press MODE button for more than 2 seconds,
idle screen is displayed.
Other Settings
⑻ Unchecked calling number notification
(Function that notifies unchecked calling number.)
① You can enter into Setting Mode by pressing MODE button
for more than 2 seconds at idle screen.
② After moving to using arrow keys, enter into setting mode
by pressing SET button.
③ Move to mode using arrow keys and enter into change
mode by pressing SET button.
④
Select desired setting out of [ON], [OFF] using arrow keys.
·When you set as [ON], upper right LED light flickers every minute
if there is unchecked calling number. (Initial setting value is OFF.)
LED light
PRGH
VHW
SZU
⑤ When you press SET button for more than 2 seconds,
storing is completed and returns to previous stage.
⑥ When pressing SET button for more than 2 seconds,
it returns to previous stage.
When you press MODE button for more than 2 seconds,
⑦
idle screen is displayed.
22
Loading...