Solt SOLTPEPEATER User Manual

3

Supplies Per Models

Repeater

Installation Deck (Screw 2pcs)

Adaptor

Specification

Repeater

Model

SOLTPEPEATER

Frequency(MHz)

433.0500 ~ 434.7900

Freq Stability

±5 ppm

Data Rate

1800 bps

Channel space

12.5 KHz

Modulation

FSK (±3KHz)

Output Power

10mW (Max)

Sensitivity

-118dBm (at 12dB)

Power Supply DC 12V/1A Adapter

Dimension(mm) 146W × 90L x 32H

Battery Life cycle

External Power

Antenna

Tilt base snap-in_dipole (External)

User's Guide

SOLTREPEATER

4 5

Repeater

/P3FDFJWF

① Folding antenna : 180 degrees pivot

④ Setting buttons

③ Wall mount holes : Refer to item 4 of Installation Guide in page 53.

⑤ Display

⑥ Adapter input: DC12V 1A (Use the supplied adapter)

② Bell number indicator : activated led number varies by different models.

Limited accessary warranty: malfunctioning of supplied adapter during its use is not covered by manufactures' warranty.

Purchasing an adapter with AC110~22OV input, DC12V 1A output is recommended.

PWR Red led indicates power is on

RX Blinking Red led indicates bell model

TX Blinking Green led indicates pager model

MENU / ESC

·Menu button in setting mode

· alphabetic and numeric changing button

▲ ▼ ·up /down

◀ ▶ ·left / right buttons

SET / PWR

·Storing button for set value

·Dower button

[Wall mount bracket installation]

Missed call icon

.&/6

&4$

ⶸⶼⶾ ⶺ

4&5 183

/P3FDFJWF

① Retractable antenna

⑤ Call number Display

② Status indicator

[Back cover]

④ Setting buttons

⑥ Adapter input

(DC 12V 1A)

Name of each section

③ Holes for wall mount

Front

Back

Input : AC110~220V

Output : DC12V 1A

6 7

Repeater

② Bracket Installation

③ Power Cord

(Use the adapter provided in the package.)

④ Wall Mounting

(Pull down the unit until clicking sound is heard. )

Install at roof like picture above, it is better if antenna direction go downward. In the case of cannot be installed to the roof install rear the roof. Once decided where to install, fix the mount.

Installation guide

① Location

※ Transmitter must be installed with in 100% reception area.

※ This product is needed to avoid moisture and water (It can be cause of breakdown) Recommend to install away from water. If needed to install outside of building, install where does net get wet.

It is most appropriate to install A location which is located within 100% reception area. (See map a picture above)

Transmitter (Main or Bell) Location.

100% Reception Area.







To assure the finest performance, please read this manual carefully.

8 9

Repeater

Repeater selection mode (Cbr / CPr)

·Sets the repeater as call bell repeater or pager repeater.

·Entering setting mode as [E1 Rsel] is displayed.

·

[E1 Rsel] is displayed and returns

to previous step.

·

[ST-r5] is displayed and ready for reception.

⑴ Press and hold (MENU) button for 3 seconds.

⑵ Press (SET) button.

⑶ Press (▲▼) buttons. (Cbr / CPr)

⑷ Press (SET) button.

⑸ Press (MENU) button.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

※ Press (▲▼) buttons to select different setting mode.

Cbr : Extends bell receiving range by relaying

bell's data to main transceiver.

CPr : Extends pager receiving range by relaying

main transceiver data to pager.

· [Cbr or CPr] is displayed.

Repeater setting modes

Listed items below can be set by using user setting buttons.

E1

Repeater selection mode

Sets the repeater as call bell repeater or pager repeater.

E2

Download mode

Downloads registered call numbers from main transceiver.

E3

No receive call number setting mode

Selects call numbers that are not desired to receive.

E4

Call redundancy interval setting mode

Sets interval for redundant calls. (default value is 3 seconds)

E5

Call number deleting mode

Deletes registered call numbers.

E6

Call number registering mode

Registers new call numbers.

E7

TX delay time setting mode

Sets delay time for received call number from bell.

[TBD]

10 11

Repeater

·Entering setting mode as [E1 Rsel] is displayed.

·

[E3 Daof] is displayed.

·Registered call number is displayed.

⑴ Press and hold (MENU) button for 3 seconds.

⑵ Press (▲) button twice.

⑶ Press (SET) button.

⑷ Press (▲▼) buttons to select a Call number don't want to receive.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

No receive call number setting mode

·Selects call numbers that are not desired to receive.

·Selected call number is displayed.

·

[No Receive] button toggles each time

SET button is pressed.

⑸ Press (SET) button to select desired receiving mode.

MENU

ESC

▲

◀ ▶

SET

PWR

▼

※ To set another receiving mode, repeat steps (4) to (5).

⑹ Press (MENU) button.

MENU

ESC

▲

◀ ▶

SET PWR

▼

·[ST-r5] is displayed and ready for reception.

/P3FDFJWF

e.g.) Call number 200 is set to not receive when [No Receive] icon is displayed.

Download mode

·Downloads registered call numbers from main transceiver.

·[E2 Down] is displayed.

·[---] is displayed.

·[---] is displayed during downloading is in progress.

·[E2 Down] is displayed when downloading is completed and returns to previous step.

⑵ Press (▲) button once.

⑶ Press (SET) button.

⑷ Press (SET) button.

⑸ Press (MENU) button.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

·Entering setting mode as [E1 Rsel] is displayed.

⑴ Press and hold (MENU) button for 3 seconds.

MENU

ESC

▲

◀ ▶

SET PWR

▼

·[ST-r5] is displayed and ready for reception.

※ Press (▲▼) buttons to select different setting mode.

[TBD]

12 13

Repeater

·

" It has been deleted." is played.

·To delete another call number, repeat the processes from (4) to (5).

⑸ Press (SET) button.

⑹ Press (MENU) button.

MENU ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

⑷ Press (▲▼) button. Select the call number you want to delete.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

Call number deleting mode

·Deletes registered call numbers.

·[E5 Dele] is displayed.

⑵ Press (▲) button 4 times.

⑶ Press (SET) button.

MENU

ESC

▲

◀ ▶

SET PWR

▼

·Entering setting mode as [E1 Rsel] is displayed.

⑴ Press and hold (MENU) button for 3 seconds.

MENU

ESC

▲

◀ ▶

SET PWR

▼

·Registered call number is displayed.

·Selected call number is displayed.

·

[ST-r5] is displayed and ready for reception.

⑸ Press (SET) button.

⑹ Press (MENU) button.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

Repetition call setting mode

·Sets interval for redundant calls.

·

[E4 Dupt] is displayed.

·

[3] is displayed.

·Selected number is displayed.

⑵ Press (▲) button 3 times.

⑶ Press (SET) button.

⑷ Press (▲▼) buttons. Sets the desired number.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

·Entering setting mode as

[E1 Rsel] is displayed.

⑴ Press and hold (MENU) button for 3 seconds.

MENU

ESC

▲

◀ ▶

SET PWR

▼

·[ST-r5] is displayed and ready for reception.

※ Press (▲▼) buttons to select different setting mode.

·[E1 Rsel] is displayed and returns to previous step.

※ 3 is set for default. (Unit : second)

14 15

Repeater

⑺ Press and hold (SET) button for 3 seconds when registration is finished.

⑸ Press (SET) button.

MENU

ESC

▲

◀ ▶

SET

PWR

▼

MENU

ESC

▲

◀ ▶

SET

PWR

▼

·Registration for selected call number is completed.

·The number of screen is again blinking.

·To register another Bell, repeat the processes from (4) to (6).

⑹ Press the button to register.

䌫䌬䌅䌚䌍

·Selected-number from (4)section is displayed on the screen and the number stop blinking.

·

[ST-r5] is displayed and ready for reception.

Call number registering mode

·Registers new call numbers.

·

[E6 Breg] is displayed.

⑵ Press (▲) button 5 times.

⑶ Press (SET) button.

⑷ Press (▲▼◀▶) buttons. sets desired to call number.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

· Press (◀▶) buttons to move to different digits.

· Press (MENU) button to toggle input mode from / to numeric and English modes.

Number

mode

English

mode

%ODQN

·Entering setting mode as [E1 Rsel] is displayed.

⑴ Press and hold (MENU) button for 3 seconds.

MENU

ESC

▲

◀ ▶

SET PWR

▼

·Blinking [0] is displayed.

1716

Repeater

TX delay time setting mode

·Sets delay time for received call number from bell.

·[E7 Txdt] is displayed.

·

[0] is displayed.

·10(1Second), 20(2Second) ... 100(10Second)

·Selected number is displayed.

⑴ Press and hold (MENU) button for 3 seconds.

⑵ Press (▲) button 6 times.

⑶ Press (SET) button.

⑷ Press (▲▼) buttons. Sets the desired number.

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

MENU

ESC

▲

◀ ▶

SET PWR

▼

※ '0' is default value : transmits as soon as receiving a call.

·[ST-r5] is displayed and ready for reception.

⑸ Press (SET) button.

⑹ Press (MENU) button.

MENU

ESC

▲

◀ ▶

SET

PWR

▼

MENU

ESC

▲

◀ ▶

SET

PWR

▼

·Entering setting mode as [E1 Rsel] is displayed.

※ Press (▲▼) buttons to select different setting mode.

· [E1 Rsel] is displayed and returns to previous step.

Solt SOLTPEPEATER User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual