SOLOMON DVM1815Z-A0, DVK1815Z-A0 Datasheet

SOLOMON SYSTECH

SEMICONDUCTOR TECHNICAL DATA

Rev 0.1

08/2000

Copyright © 2000 SOLOMON Systech Limited

Product Information

SSD1815Z Development Kit

DVK1815Z-A0 is a demonstration of SSD1815Z working on a (96 X 64 + 1
icon line) panel. It is intended to help users expedite their design-in of SOLOMON
LCD driver.

PACKAGE CONTENTS

DVK1815Z-A0 consists of the following:

1) LCD Module (96 X 64 + 1 icon line) (DVM1815Z-A0)

2) LCD Drawing (optional)

3) Programmed 8051 MCU Board (EVM89C52-A0)

4) 8051 MCU Board Schematics (EVM89C52-A0)

5) Demo Program in C Language (PRG1815Z-A0)

SYSTEM REQUIREMENT

DVK1815Z-A0 is good enough to serve as a standalone demo. 2 X AA 1.5V
battery is required for normal operation. For engineering evaluation on the LCD
driver and/or LCD panel, a 8051 Incircuit emulator (ICE) is required. The one
Solomon Systech is using is EMMIT 8051 ICE from Syber Electronics Co Ltd.
User can get its information from the email: [e-mail]

LCD MODULE

Table 1 DVM1815Z-A0 pin assignment

Pin Number

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

LCD Module

VDD

RES

NC

D/C

R/W

CS1

VSS

D0

D1

D2

D3

D4

D5

D6

D7

NC

NC

VSS

NC

NC

NC

NC

NC

NC

8051 MCU
Board

VOUT

PA-04

PA-05

PA-01

PA-07

PA-06

GND

PB-00

PB-01

PB-02

PB-03

PB-04

PB-05

PB-06

PB-07

PA-00

VOUT

GND

+9V

P34

P35

P36

P37

NC

DVK1815Z-A0

Figure 1 DVM1815Z-A0 outlook

The LCD module has been configured as follows

1) size: 96 X 64 + 1 icon line

2) COG Package

3) 4X DC-DC converter to generate VEE

4) Internal feedback resistor which is software programmable is used to
generate VL6.

5) 6800 8-bit parallel interface.

6) 24 pins single inline (SIL) header is used to connect 8051 MCU Board to LCD
Module. Please refer to Table 1 for pin assignment.

ORDERING INFORMATION

Item Ordering Part Number
SSD1815Z Develop-

ment Kit

DVK1815Z-A0

SSD1815Z Develop­ment Module

DVM1815Z-A0

2

SOLOMON

DVK1815Z-A0

Rev 0.1

08/2000

8051 MCU BOARD

The 8051 MCU Board is powered up by 2 X AA 1.5V battery. A 2X DC con­verter (ICL7660) is used to generate 4.8V to supply 8051 MCU. This voltage is
also regulated by LM317 to generate VOUT (adjustable from 1.8V to 3.5V)
which in turn powers up solomon LCD driver. All logic output from 8051 are
down-converted from 4.8V to VOUT through 74HC4050 non-inverting buffer.
User can change VOUT by tuning T1 (1K trimmer).The MCU board is configured
to run at a speed of 4MHz. 4 dummy keys are reserved for developing user­interactive application such as tuning contrast.

Figure 2 EVM89C52-A0 outlook

Figure 3 DVM1815Z-A0 schematics

3

SOLOMON

DVK1815Z-A0 Rev 0.1

08/2000

PROGRAMMING NOTE

/****************************************************************************
* PRG1815Z-A0 *
* 1815 Evaluation Program *
*****************************************************************************/
#include "reg8751.h"
#define controlport P0
#define dataport P1

/****************************************************
* A) HardWare Interface *
* *
* PORT A 7 6 5 4 3 2 1 0 *
* RW CS -- RES -- -- DC -- *
* PORT B 7 6 5 4 3 2 1 0 *
* D7 D6 D5 D4 D3 D2 D1 D0 *
* *
****************************************************/

/****************************************************
* B) Command Table per device *
****************************************************/
#define DisplayOff 0xAE
#define DisplayOn 0xAF
#define DisplayStart 0x40
#define PageAddr 0xB0
#define ColAddrHi 0x10
#define ColAddrLo 0x00
#define SegRemapOff 0xA0
#define SegRemapOn 0xA1
#define NormalDisp 0xA6
#define ReverseDisp 0xA7
#define SWRest 0xE2
#define ComRemapOff 0xC0
#define ComRemapOn 0xC8
#define PwrCtrlReg 0x28
#define OPampBuffer 0x01
#define IntReg 0x02
#define IntVolBstr 0x04
#define IntRegRatio 0x20
#define ContCtrlReg 0x81

#define Device SSD1815Z /* device under demo */
#define ColNo 96 /* number of Column/Seg on LCD glass*/
#define RowNo 64 /* number of Row/Com/Mux */
#define PS 1 /* fixed to Parallel mode */
#define PageNo 8 /* Total no of RAM pages */
#define IconPage 8 /* Icon Page number */
#define SSLNameNo 3

/****************************************************
* C) Global Variable Definition *
****************************************************/