Sollatek Voltsure Ultima LCD 650, Voltsure Ultima LCD 1500, Voltsure Ultima LCD 1000, Voltsure Ultima LCD 2000 Instruction Manual

Ultima LCD

Line Interactive UPS

Instruction manual

Voltsure

™

Important: This manual contains important safety instructions.
Keep this manual handy for reference.

• Before using this product please read all instructions carefully.

• Keep these instructions for future reference.

• All specifications are subject to change without prior notice.

IMPORTANT SAFETY WARNING (SAVE THESE INSTRUCTIONS)

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of

conductive contaminants. (See the specifications for the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS’ cooling vents and avoid exposing the unit to
direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces.
CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens,
or vacuum cleaners to UPS.

CAUTION! Do not plug the UPS input into its own output.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing

vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to
properly disable the UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! With the installation of this equipment, it should be prevented that the sum of the leakage current of the UPS to the

connected consumer exceeds 3.5mA.
ATTENTION ! Hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous voltage still
may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus
pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary.
CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the
required precautions. Keep unauthorised personnel away from batteries.

CAUTION! When replacing the batteries, use the same number and type of batteries.
CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.
CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the battery or batteries.

Released electrolyte is harmful to the skin and eyes.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The following precaution should be

observed before replacing batteries:

1) Remove watches, rings, or other metal objects.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting batteries terminal.

1. PACKAGE CONTENTS

You should have received the following items inside of package:

• UPS Unit

• Quick Guide

• USB Cable

• CD Rom

2. LCD PANEL

1. Input informat ion

2. Output information

3. AC mode indicator

4. Battery mode indicator

5. Load level indicator

6. Battery capacit y indicator

7. Overload indicator

8. Low battery indicator

9. Fault indicator

2

3. INSTALLATION AND INITIAL STARTUP

NOTE: Before installation, please inspect the unit. Ensure nothing inside the package is damaged.

Placement & Storage Conditions

Install the UPS in a protected area that is free of excessive dust and has adequate air flow.
Place the UPS away from other units at least 20 cm to avoid interference. Do NOT operate
the UPS where the temperature and humidity is outside the specific limits. (Please check
the specs for the limitations.)

Connect to Utility and Charging

Plug in the AC input cord to the wall outlet. For best results, charge the battery for at least
6 hours before initial use. The unit charges its battery while connected to the utility.

Connect the Loads

Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power switch of UPS
unit, then devices connected to the UPS will be protected by UPS unit.

CAUTION: NEVER connect a laser printer or scanner to the UPS unit. This may cause damage to the unit.

Connect Modem/Phone for Surge Protection (Only for the model with RJ-11/45)

Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of the UPS unit.
Connect from “OUT” outlet to the computer with phone line cable.

Connect Communication Cable (Only for the model with USB port)

To allow for unattended UPS shutdown/start-up and status monitoring, connect the communication cable one end to the USB port and
the other to the communication port of your PC. With the monitoring software installed, you can schedule UPS shutdown/start-up and
monitor UPS status through your PC.

Turn On/Off the Unit

Turn on the UPS unit by pressing the power
switch.Turn off the UPS unit by pressing the
power switch again.

20cm

4. SOFTWARE DOWNLOAD
& INSTALLATION

(Only for the model with communication
port)

Please either: use CD provided
or: follow steps below to download and
install monitoring software:

1. Go to the website http://www.power-

software-download.com for the latest

version to download.

2. Click ViewPower software icon
and then choose your required OS to
download the software.

3. Follow the on-screen instructions to
install the software.

4. When your computer restarts, the

monitoring software will appear as an
orange plug icon located in the system

tray, near the clock.

Four

output

Receptacles

Telecom

inlet

VDU

CPU

Mains inlet

Modem

AC Input

Circuit

breaker

Cooling fan

USB port

Connections

Rear panel shown for
demonstration purposes.
Please refer to section 6. for
individual rear panels.

3