MIC
VOL
PWR
MUTE
GPS
MAP
RESET
USB
AUX
6.75
Double Din with fixed panel
SD
AVN67 5D
AVN675D
CONTENTS
Panel function description
Remote control function
Turn on/off Host
Access main interface
Wallpaper and Logo Setup
Radio Function Operation
Disc Function Operation
U Disc/SD Card function operation
BT Function Operation
Music function operation
External input operation
NOTE
1. Please read the instructions before using the unit, the damage caused by not following the instructions will not enjoy the warranty.
2. To drive safely and avoid break the traffic rules, do not watch program and operate the unit while driving.
3. To avoid short circuit, please do not exposure the device to rain.
4. To avoid short circuit, please do not put in the device or any metal objects left behind.
5. Not open the machine for maintenance by yourself, please go to the professional repair service station for repairing.
6. When the engine is turned off, please do not use the car audio a long time, otherwise the battery may run out.
7. Do not insert anything to the device’s vent and other openings.
8. Damage to the screen carefully! Do not use sharp objects push, rub, Stroke the screen.
03
Compass
04
Counter
06
GPS Navigation Function Operation
06
Other function operation
06
Basic operation setup menu
07
Access setup interface
08
General Settings
09
Trouble shooting
10
Accesories
11
WIRING DIAGRAM
11
SPECIFICATIONS
SPECIFICATIONS
12
12
12
13
14
14
16
17
18
18
19
Power supply
Power range
Max operate current
Ground system
Bluetooth
Audio
Video
Display
Resolution
Max output power
Subwoofer Output
FM tuner
Frequency range
Signal/Noise ratio
Stereo separation
Search station volt
Distortion rate
AM tuner
Frequency range
Limit noise sensitivity
DVD player
Signal/Noise ratio
Frequency response
DC 12V
10.8-16.0V DC
Negative ground
RCA 4 Output, RCA 2 Input
RCA 2 Output, RCA 1 Input
87.5-107.9 MHz
15A
2.0, class II
16:9
800*480 Pixels
4*25W
1 Output
55dB
30dB
20-30dBuv
1.5%
530-1710 KHz
32dB
70dB
20Hz-20KHz
02
19
Accessories
Accessories
Left Bracket
Right Bracket
White screw
Warranty card
Registration card
Manual
QRG
Power harness
Trim
18
WIRING DIAGRAM
This player is equipped with ISO standard connector, please follow
below instruction:
1
1
8
● Red - ACC ON (+12V)
● Yellow – 12 V Constant
● Black – Ground wire
● Blue - Power Antenna / Remote Amp Turn On
● Orange – Back-Up Camera Trigger (+)
● Grey/Grey black - Right front speaker (+/-)
● White/White black - Left front speaker (+/-)
● Purple/Purple black - Right rear speaker (+/-)
● Green/Green black - Left rear speaker (+/-)
● Parking Brake (-)
1
Panel function description
MIC
VOL
PWR
MUTE
GPS
MAP
RESET
USB
AUX
AVN675 D
1
1. PWR / VOL button
1
1
1
1
Press this button to power on; In boot-up state, long press this
button to power off; short press to return to main menu under an
mode, rotating the knob to adjust the volume.
2. MUTE button
Press the button to close volume output, re-press it to resume
previous volume level.
3. GPS button
Press it to enter or exit the navigation.
4. MAP slot
Insert a map card to read navigation map data.
5. RESET
Press this button can back to default mode.
6. USB slot
SD
Connect USB mobile device to read video, audio and image files
of large volume.
Warning: You can only use either front or rear USB at a time.
Never connect both front and rear USB at the same time!
This could cause malfunctions.
7. AUX slot
To input external audio.
Warning: You can only use either front or rear AUX at a time.
Never connect both front and rear AUX at the same time.
8. Eject disc
Press this button can eject the disc.
9. IR
To receive infrared signals from the remote control matched with
the unit.
10. Disk load slot
Disk loading / exit window.
11. SD slot
Connect the SD memory card to this socket, and the unit can play
MP3 music.
12.MIC
BT microphone input socket.
03
Remote control function
1. POWER
Press once to switch on, press again to switch off.
2. MUTE button
Press once to turn off audio output, press again to resume volume
level.
3. NAVI button
Press it to enter & to exit the navigation.
04
4. SOURCE button
Press this button to choose audio sources.
5. EQ button
Press this button
6. SEEK+ ( )/ SEEK- ( )button
Press this button to manual turning, sped or quick back, previous
song and next song.
7. VOL+ ( )/ VOL- ( )
Press this button to increase or decrease volume level.
8. SEL button
Press this button to choose sound feature.
9. LOUD button
Press this button to startup LOUD function.
10. BAND -P/N button
In radio mode, press this button to choose band.
In VCD, DVD mode, press this button to choose PAL, AUTO or
NTSC system.
11. LOC/RDM button
In radio mode, press this button to switch between local and
direction, In VCD, CD mode, press this key to randomly play.
12. STOP button
Press this button to stop playing.
13. PLAY/PAUSE button
Press this button to switch between play and pause, In stop mode,
press this button to play.
14. ST/PROG button
In radio mode, press this button to choose stereo or mono station.
In audio mode, it can help stop button to programmed play.
at the can switch between different modes.
Troubleshooting
PROBLEM CAUSE
Cannot power on
After ignition switch
off, setting information
all lose
Poor performance of
radio station
Cannot load disk
Cannot play disc
Cannot switch
language/subtitle
No image
Cannot watch image
during driving
Check fuse
Some factors cause MPU wrong operation
Change battery or fuse
Weak signal
There is a disk inside
Disc is scratched
Put wrong side of disc into the unit
There is only one language/subtitle in disc
Other factors cause MPU wrong operation
It’s not allowed to watch image during driving
CORRECT ACTION
Change fuse same as the old one
Press RES button on the panel by
power on
Reset information and save
Move the car to another place, then research
Eject disk, then, slot in new disc
Change new disc
Insert in the disk with sign side up
Clean lens by lens clean discLens is dirty
If disc is not with multi-language/subtitle, it cannot
switch language/subtitle
Press [RES] button on the panel by penpoint, then,
power on
Park the car in a safe place, put the car stall in “ P ”
postion, pull up the hand brake, parking brake wire
must be grounded
penpoint, then,
17
General Settings
In the set interface click [GENERAL] icon, into the General set
interface. (Password: 888888).
General settings have been set at the factory.
Language setting
In the General Settings screen click [LANGUAGE] icon to enter the
Language setting interface, as shown below:
Slide up and down to select your preferred language mode.
Regional radio
In the General Settings screen click [RADIO] icon to enter the
Radio setting interface, as shown below:
Select your desired area.
16
System setting
In the General Settings screen click [SYSTEM] icon to enter the
System setting interface, as shown below:
You can choose the system settings interface has the feature is
turned on or off.
Car Set settings
In the General Settings screen click [Car Set] icon to enter the
agreement setting interface, as shown below:
You will need to set protocol, click the icon to confirm the
save the settings.
Version Information
In the General Settings screen click [VERSION] icon to enter the
Version Information interface, as shown below:
The version information is displayed please prevail in kind.
15. 0-10+ button
Press this button to choose desired song, section, preset stations.
Decimal numbers, for example the 19th song, press 10+ and 9
button.
16. AMS/RPT button
In radio mode, press this button to browse stored stations. In audio
mode, press this button to play repeatedly.
17. TITLE button
In DVD mode, press this button to play back to the top menu of
disc.
18. AUDIO button
In DVD mode, press this button to switch language of dialogue.
In VCD mode, press this button to choose left track, right track,
and stereo.
19. GO TO button
In DVD mode, press this button, you can define playing time.
20. SUB-T button
In DVD mode, press this button to switch language of subtitle.
21. PBC button
In VCD mode, press this button to display all song menus, work
with number button to choose songs.
22. UP, DOWN, LEFT, RIGHT, ENTER button
In DVD mode, press this button to move cursor up, down, left,
right to choose item in menu, Press the enter button to confirm
choice.
23. SLOW button
In audio mode, press this button to slow backward and slow
forward.
24. SETUP button
In audio mode, press this button to choose different set items.
25. OSD display
Press this button to display the title chapter and the left time.
26. ZOOM button
In DVD/VCD mode, press this button to ZOOM in.
27. MENU button
Press button to back to the main menu.
BATTERY CHANGE
When control distance of remote control becomes shorter or no
function, please change battery, please confirm polarity before
change.
One hand press stopper, then pull out battery.
Put battery into controller.
Insert battery holder into controller.
05
Turn on/off Host
When the ignition switch is put in ACC or ON position, Press [ ] button on the front panel to turn on the unit. After the host starts,
hold [ ] button for 3 seconds , the host will turn off.
Access main interface
In boot-up state, press [ ] button on the panel to switch to main interface, as shown in below picture:
Touch in different interface style to switch between.
1.
Press and hold the hide icon hold to the left and right drag, you can hide the location of the icon to the left or right.
2.
3. Click the icon or gently with a touch pen or finger to the left and sliding screen to toggle the main menu page.
4. To reset the shortcuts with a touch pen or finger to hold down the icon to drag the icon to drag the icon to the shortcut bar to the
bottom of the screen, move over the icon will replace the old icon. If you want to delete the shortcut icon, first press and hold the icon
until the trash can icon and then drag to the trash.
5. The icon at the touch on the main interface to switch between day, night and off-screen three modes.
6. Touch the function icons so as to access the corresponding function operations.
7. Double-click the watch icon to enter the clock setting interface:
Click the icon to select your favorite type of clock. Click the icon unlock unlocked drag minutes
to set the time, set up and click again to icon to lock the clock.
Wallpaper and Logo Setup
Click on the main interface [wallpaper] icon into the wallpaper and boot screen settings interface,
you can choose your favorite wallpaper and boot screen.
Note: The start-up screen has been set at the factory.
06
Touch calibration
If touch calibration error occurs, you can adjust the touch
coordinate by “Touch calibration”. Click [CALIBRATION] icon
on setup interface, click OK to pop up a [Do you want to
calibration?] as shown below, click OK to confirm to access touch
calibration interface:
Touching methods
Use touch pen to click the center of”+” icon, and move along
with center of “+” icon so as to calibrate the screen, It shall
automatically save data and exit after screen calibration. Please
accurately click all positions on screen, or the accuracy of touch
calibration shall be affected.
Serial port setting
In the set interface click [SET COMM] icon, into the Serial port
set interface.
Choose good then click the icon to save your settings and exit
the serial port settings interface.
Steering wheel setting
Click the settings interface [STEER] icon into the steering wheel
settings interface.
Steering steps:
The original line of control of
the vehicle side, the positive,
the negative and machine side
control line cathode, anode
connection after connection:
① Touch [Reset] and press
above the steering wheel buttons one by one, and record the
appropriate sequence and function, touch [allocation].
The steering wheel buttons
② Touch the desired distribution voltage value (such as: 2.00V).
③ select the appropriate settings (such as: volume +).
④ completed the steering wheel buttons will display the
corresponding function.
⑤ After completing the settings, touch [OK] to save the settings.
⑥ For the reset function, can touch [Reset] (the original settings
will all be cleared), and repeat Step ② ~ Step ④
⑦ You can also choose to set a good model of the steering wheel.
Click the models select] icon pop-up model selection interface,
select your car type click OK icon to save the settings.
forresetting.
15
Basic operation setup menu
Access setup interface
Click on the main screen [Setup] icon, enter the setting interface.
With a finger or touching pen to gently sliding screen can be set
about switching interface.
Navigation setting
Navigation path has been set at the factory, please do not enter
the navigation setup interface to change the path freely, otherwise
the procedure many lead to abnormal navigation.
Video setting
In the set interface click [VIDEO] icon, into the video set interface.
Brightness:
Forbid play on run: Driving ban and click on play icon can
open/close the function (Optional).
Drag icon can adjust video the screen brightness.
14
Audio setting
In the set interface click [AUDIO] icon, into the Audio set interface.
Click into sound effect default interface.
Press into loudspeaker interface, click to adjust the
channel of loudspeaker, touch to get back to initial setting.
BEEP: click that icon to switch on/off that.
LOUD: click that icon to switch on/off that.
GPS. MIX: click that icon to switch on/off that.
EQ: click that icon to switch different mode.
Time setting
Click the Settings interface Time setting icon, enter the Time
settings screen, as shown below:12h/24h interchangeable,
In the year, month, day, hour, sub-office slide up and down to
the relevant settings.
Zone is set to enter the time zone settings interface when clicked.
Choose the time zone, click the icon to save your settings
and exit the time setting interface.
Radio Function Operation
1. Enter/exit
Touch [Radio] icon in the main interface to enter into the radio interface.
Touch [ ] icon to return to main interface, and then touch other function icons so as to exit
radio mode.
2. Operation stored radio
Each band can be stored six radio stations, radio stations can be stored directly click (P1-P6)
choice, and will be displayed on the screen.
3. How to save radio stations
Select a band, and then select a radio station. Press and hold button (P1-P6) to select the preset
number will appear in the corresponding number button on the screen.
4. Band selection
] icon so as to switch among FM1, FM2, FM3, AM1, AM2 bands.
Touch [
5. Search/Save radio stations
Short touch the [ ] button, browse 1-6 sets of bits stored on the radio, Long touch the [ ]
button to long-automatic station search, and the strongest radio signals P1-P6 are stored in the
display position on the table.
6. Play radio station selection
Touch [ ] icon pop-up selection sets the keyboard input radio frequency selectable radio frequency spectrum or you can drag
directly touch the icon to select a stored radio station.
7. Other Functions
Touch [ ] icon to access sound setting interface.
Touch [ ] icon so as to turn on/off loudness function.
Touch [ ] can enter icon spectrum interface. Double-click the spectrum can switch over the spectrum style.
Touch [ ] icon so as to turn on/off Long/Short-Range function.
Touch [ ] icon to turn on/off stereo.
8. RDS Function
RDS function provides series information (such as traffice information, name of station) ,and can automatically switch to
the station with stronger signal and carries the same program.
AF: touch the button to turn on/off AF mode.
TA: touch the button to turn on/off TA mode.
PTY: touch the button the screen displays program types, users can search station according to program type.
NOTE: If the unit does not have RDS function, it has no AF/TA/PTY function, .
Touch the corresponding icon had no effect
Sliding around
07
Disc Function Operation
1. Play/eject disc
Play disc
Insert the disc into the disc slot with the printing surface up, system will detect the disc and automatically take it in to read and play.
Eject disc
(1) Click button on the panel to eject the disc.
(2) If a disc has not been took away 15 seconds after it is ejected, system will automatically take in the disc but not play.
Do not insert two discs or more.
2. DVD/VCD disc playback
During playback of disc, touch the middle lower area of the screen to pop up the touch menu, operate the touch menu to perform
various playback controls.
3. CD Disc Playback
After a CD is inserted, system shall access disk reading state immediately.
When there is a disk in the device, click [Disk] at the main interface so as to access disk reading state.
After the disk being read out, system shall automatically play in sequence.
4. MP3/JPEG disk playing
When the disk contains readable files, such as MP3/JPEG files, it shall be automatically read out and played after slipping into
DVD player.
During playing, touch the screen area and the touch menu shall pop up. Operate the touch menu
for playing.
5. Touch Menu Function Description
The disc read, touch area of the screen, pop-up touch menu. Operate a variety of playback controls
the touch menu.
Forward/Backward play
Play/Pause
The previous/next song
Stop
08
Back to Root Menu
Access title menu
Repeat play
Volume button Number Button
The next page menu
Zoom in/out
Channel conversion Language Selection
Random play
Scanning
00 :0 0:0 9 00 :0 4:4 8
Other function
Rearview function
In any running state, the video signal can switch to reverse video state when reversing the car, and the system shall return to
running state after reversing the car.
Warning
Do not rely on CCD system completely, please make sure
your car is safe by your eyes during driving. Back rearview
system only assists in driving. As the distance range of
rearview system is limited, completely relying on the
rearview system during driving may cause accidents.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
operation
Reverse field simulation
its initial
Rearview backup image
13
COMPASS
In the main interface touch [COMPASS] icon, into a compass interface.
COUNTER
In the main interface touch [COUNTER] icon, into the counter interface.
GPS Navigation Function Operation
1. Navigation Function Operation
For detailed operation of navigation function, see “Navigation Operation Manual”.
2. Receiving signal error
When the satellite signals can be normally received, the error of standard GPS shall be about 7 meters, Driving on parallel sections,
there shall be error even the product has auto-correct function. The normal receiving of satellite signals shall be affected and cause
error in following environment.
In tune
3. Satellite receiver
Navigation system can keep receiving eight satellite signals. As a general rule, the navigation system
can figure out your accurate location after received 3-4 satellite signals. But sometimes, weather and
tall buildings in the city shall affect the signal receiving effect, as is shown in following figure:
12
Among tall buildings At the boulevard The antenna is sheltered Underground parking Overpass or viaduct
Forward/Backward play
Click the button, forward/backward play.
The previous/next song
Channel conversion
Click Switchable channel the button, .
Back to Root Menu
Click the button the DVD state can return to the root menu of
the disc, VCD state can enter the PBC menu and playback.
Access title menu
Press this button to return to title menu of the disk. Directly click
menu bar at title menu interface for playing.
The previous/next songClick the button, .
Repeat play
In playing state, touch this button to start repeat play function:
Chapter repeat → Title repeat Off.→ Entire disc repeat →
During VCD playing, this function only works when PBC is off.
Language Selection
Note: the need to support the the subtitle language discs have
this feature
Number Button
Click the button, pop-up numeric keypad. By click the numeric
keypad for direct selections played.
can switch subtitle language.Touch the button,
U Disc/SD Card function operation
When there is a USB device/SD card connected, the unit can conduct the playback of
Insert/Eject USB storage device
1. Connect a U disc recorded with media information to the unit by a USB connecting cable.
2. When there is a need to eject the USB device, exit the USB device playback screen first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit correctly until it is locked.
When pulling out the SD card, exit SD card playing state first, then press the SD card and it shall pop up after unlocking.
2.
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the unit has connected with a USB device or SD
card, touch [USB] icon in the multimedia interface to enter into the external storage playback interface; Touch [SD] icon to enter into
the SD card playback interface. During playback, touch the top center area of the screen to pop up the touch menu, operate touch menu
to perform various playback controls.
Play
After SD card/USB removable device being read out, the operation methods are similar to disk operation methods.
audio/video/image files in the USB device/SD card.
09
BT Function Operation
1. Enter/exit
Touch [BT] icon in the main interface to enter the BT interface,
Touch icon to exit BT interface.
2. Pair/link
To use hand-free function, make connection first, i.e. match the host with the
BT BT
Operation methods:
Set the host to be matching state, and open the of your mobile phone and use the mobile phone
to search device, the mobile phone shall prompt to match password with the when it has searched
the device. Input password (0000) to the mobile phone and confirm. The mobile phone shall
BT BT
prompt whether authorize to this device, please select [Yes]. Phone and shall automatically connect
within 20 seconds. Under any working mode, the host shall convert to state if there is an incoming
call. And the host shall restore to current mode after hanging up.
When the device matches with this device, the connection status shall display , otherwise,
it shall display .
3. Dialing
You can dial on mobile phone directly or input phone number through the number buttons on the
screen, click to delete if there is input error. After input the phone number, click to make a call.
4. Call records
In the BT interface of click to access call records interface as PIC 2:
5. Phone book
After the cellphone gets connected to the unit, you can read records in the phonebook of your
cellphone and store information in the phonebook of the unit. In the BT interface of click
to access Phonebook interface as PIC 3:
Touch icon in the phonebook interface, the unit will automatically download phone numbers
and put them in order.
6. BT Music
In the BT interface of click to access BT music interface as PIC 4:
BT
Dialed numbers: Touch this button to check all the dialed phone numbers.
Received calls: Touch this button to check all the phone numbers of received calls.
Missed calls: Touch this button to check all the phone numbers of missed calls.
Delete: Touch the button to delete a selected record.
All Delete: Touch the button to delete all information in phone book.
BT
as PIC 1:
mobile phone.
BT
BT
BT
10
Previous song
PIC 1
PIC 2
PIC 3
Play/Pause
PIC 4
Next song
MUSIC function operation
Connect to Music first, touch [Music] icon on main interface to access Music
interface, as
shown in below diagram.
Random play
cycle play
previous Song/
Short press next Song
Long press fast forward playback/rewind playback
Back to the previous directory
Number Button
Click icon return to a interface
External input operation
Connect the video input plug with external video input jack, and connect the audio input plug
with external audio input jack.
Touch [AV-IN] icon on main interface to access external input interface.
Click icon into the sound settings screen.
Loudness on / off.
Play/Pause
Sound settings
Loudness on/off
Page up/down
11
Loading...