Pro 5 Bands Signal Booster
www.SolidRFCanada.com 1
Connect the world
Features
• Greatly reduces dropped calls, extends signal range, and increases data rates
• Allows multiple mobile devices to be used simultaneously
• Oscillation (or interference) detection and automatic shutdown with auto reset
• Overload protection circuit – protects cell towers from being overloaded
• Amplifies signals both to and from the cell tower
• Maximum 3 watts(EIRP) output power
• Works on all generations of 2G,3G and 4G
• Power control logic ensures maximum gain is within cellular standards
• Reduces radiation and extends battery life – up to 2 hours additional talk time in weak signal areas.
Package Contents
www.SolidRFCanada.com 2
BuildingForce 4G PRO
Cellular Signal Booster
User Manual
Booster
35702701-R5U08
Inside Antenna
ANT050501
Power Adapter
ADP0101
Inside cable 75feet
CAB017501
Outside cable 60feet
CAB016001
Outside Antenna
ANT011001
Lightning Surge Protector
ACC010101
Antenna Pole
ACC000101
Installation
1
www.SolidRFCanada.com 3
1.How it work
Step 1: The powerful outside antenna captures a voice and
data signal, and transfer it to the booster;
Step 2: The booster receives the signal, amplifies it and
rebroadcasts it by inside antenna.
Step 3: Your mobile devices get a better signal, never
experience dropped calls or slow data speed.
2. Step by step installation
Step 1: mount the outside antenna
a. Choose right position
• Find the strongest signal position in the possible install
locations by read your cell phone signal bar;
• 30cm away from any other metallic objects;
• 100cm away from any windows;
b. Mount the antenna pole;
c. Mount the antenna to the pole;
d. Connect outside cable to antenna
• Make sure connectors are screwed well;
• Seal the connectors with the glued tape;
Coverage Area
Note: cause the ability of coverage depends on output
power of booster. Any boost has a limit of amplification
factor, so finial output power is related to received signal
power level at the location of outdoor antenna.
Power level
at the outdoor antenna location
Coverage Area
(sq. ft.)
Strong (5 bars on the cellphone) 100000
Medium (3~4 bars on the cellphone) 30000
Weak (1~2 bars on the cellphone) 10000
Supported Carries
• AT&T 2G/3G/4G (HSPA+ & LTE)
• Verizon 3G/4G
• T-Mobile 2G/3G/4G
• Sprint 3G/4G
• US Cellular 3G/4G
• Metro PCS 3G/4G
• Major Canadian Carriers 2G/3G/4G
• All other carriers using 700MHz, 750MHz, 850MHz ,1900
and 2100MHz
www.SolidRFCanada.com 4
Installation
2
Step 3: arrange the booster
a. Choose position
• Be sure away from heat source;
• In ventilate dry place, temperature range should
-5~+50degree;
b. Connect the outside antenna’s connector to the “outsid-
e” labeled port of the booster;
c. Connect the inside antenna’s connector to the “inside” l
abeled port of the booster
Step 4: power on the booster
a. Plug the power adapter to the AC power;
b. Attach the cord of the adapter to the booster;
Inside antenna Outside antenna
Adapter cord
c. Connect the inside cable to the inside antenna;
Step 2: mount the inside antenna
a. Choose right position
• 20cm away from any other metallic objects;
• 50cm away from any windows;
• For the panel antenna the position on the end of the b
uilding is recommended;
b. Mount the inside antenna;
e. Set the outside antenna cable into the building
• Carefully arrange the cable along the building outside
and make sure don’t fold it;
• Fix the cable at each corner;
www.SolidRFCanada.com 5
Installation
3
Step 5: study GUI information
a. “State” there are three statements for each link: red color for alarm, green color for normal and good condition, yello
w for sleep mode;
b. “Gain” is each bands’ current gain state in dB;
c. “Pow” for each bands’ current output power in dBm;
a. state
c. Pow
b. gain
Step 6: setup each bands’ gain: press “Setup” then comes the next panel;
a. “+” add attenuation to corresponding band;
b. “-” reduce attenuation to corresponding band dB;
c. “MIRROR” or “NORMAL” change vision direction;
d. “ESC” no change and exist to information panel;
e. “OK” save what change have been done through the panel and turn to information panel;
a.
b.
c.
c.
d.
e.
Cautions & Spec.
4
Note1: Some of the 12V DC lighter power sources
will not shut down when the vehicle is turned off.
Please switch off the adapter when you leave the
car, in case the battery of the vehicle is used up.
Note2: Don’t cover the booster body with
anything, in case the power dissipation make the
booster too high temperature. Booster will shut
down when the temperature is too high itself.
Technical specification
www.SolidRFCanada.com 6
Note3
: Use only the power supply provided by
SolidRF, any other products non-approved by
SolidRF or self-made power cable may damage the
booster.
Note4: Troubleshooting
• Properly: The lights on the front panel indicate
the condition of the booster. Every time the
booster is powered on, all of the lights will be
light on in green color for around 2 seconds and
then lights off, this means the booster pass the
self check and in good condition;
• Wrong condition: If any of the lights flashing in
green light, than means the isolation between
the outside antenna and inside antenna is lower
than it should be, and self oscillate occurred.
You must switch off the booster and check the
outside antenna and inside antenna immediately.
Make sure you have followed this installation
recommended, and check every thing carefully.
If you can’t fix the problem please contact the
technician or our distributor.
Frequency
(MHz)
LTE
(band 12)
LTE
(band 13)
Cellular
( band5)
PCS
(band 25/2)
AWS
(band 4)
Uplink 698-716 776-787 824-849 1850-1910 1710-1755
Downlink 728-746 746-757 869-894 1930-1990 2110-2155
Gain Uplink 60±2 60±2 62±2 68±2 68±2
Downlink 60±2 60±2 62±2 68±2 70±2
Output power 23±2dBm(Uplink)/0±2dBm(Downlink)
Noise figure <5dB
In-band Flatness <8dB
Weight 3.5Kg
EIRP 1W
Gain adjustment 30dB
Impedance 50 ohm
Operating temperature -5°~60°
Current ≦2.5A(12V DC)
Dimension(mm) 338*230*35
www.SolidRFCanada.com 7
Warnings and Recommendations
Warning: This consumer booster is for Consumer use only.
Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC regulations. Please
contact FCC for details: 1-888-CALL-FCC.
Warning: Outside antenna orientation must be back side of inside antenna is to prevent the indoor antenna
receiving the signal emitted by outside antenna. Otherwise it will cause self-oscillation of booster.
Warning: RF safety, any antenna used with this device must be located at 20 cm (8 inches) away from
persons or by bystanders.
Warning: It will damage the mobile device and the booster if connect them with a cable directly.
Warning: Use the power supply provided by SolidRF only. Other power supplies may cause damage of the
booster.
Warning: Antenna installation is restricted to 10 meters or less height above ground, even if the antenna is
installed inside when used with a mobile device that operates in the 1710-1755 MHz band. Violation of this
requirement may subject the owner of the booster to potential FCC enforcement actions.
Warning: Never point the front of a directional antenna toward the inside antenna. Verify that both the
outside antenna and the inside antenna are connected to the booster before powering up the booster
.
RF Exposure: The manufacturer’s rated output power of this equipment is for single carrier operation.
For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB,
especially where the output is re-radiated and can cause interference to adjacent band users. This
power reduction is to be by means of input power or gain reduction and not by an attenuating at the
output of the device.
Description of network protection features:
This booster including safeguards to protect the cellular network from interference. Each Signal Booster is
individually tested and factory set to ensure FCC compliance.
1. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware.
2. The Signal Booster will amplify, but ONLY incoming and outgoing signals in order to increase coverage of
authorized frequency bands.
3. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected.
4. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal
Booster will automatically turn the power off on that band.
5. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum
of 1 minute. After 5 times consecutive such automatic restarts, if the detected oscillation still remains, any
problematic bands are permanently shut off until the Signal Booster has been manually restarted by
reconnecting power supply to the Signal Booster.
6. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.
www.SolidRFCanada.com 8
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
Contact information for providers
A subscriber must have the consent of a wireless provider to operate a consumer signal booster. Please
register your booster with your wireless service provider, refer to contact information for providers:
Sprint:
signalbooster@sprint.com
T-Mobile:
www.T-Mobile.com/BoosterRegistration
https://support.t-mobile.com/docs/DOC-9827
Verizon:
http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
AT&T:
https://securec45.securewebsession.com/attsignalbooster.com/
U.S. Cellular:
http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
Metro PCS
https://www.metropcs.com/support/signal-booster
This is a CONSUMER device
BEFURE USE ,you MUST REGISTER THIS DEVICE with your wireless provider and have
your provider’s consent .Most wireless provider consent to the use of signal boosters
.Some provider may not consent to the use of this device on their network .If you are
unsure, contact your provider.
You MUST operate this device with approved antenna and cables as specified by the
manufacturer .Antennas MUST be installed at least 20cm (8inches) from any person.
You MUST cease operating this device immediately if requested by the FCC or a
licensed wireless service provider.
WARNING.E911 location information may not be provided or may be inaccurate for
calls served by using this device.
Loading...