SolidDrive SD1 Specifications
SolidDrive
INSTALLATION & USE GUIDE
for SolidDrive SD1 into walls and ceilings
ype
T
Impedance
Frequency Response (Hz)
ecommended Amplifier Power
R
Dimensions
Weight
UL Listing
NOTE: When installed in Canada, this product must be installed in accordance
with the Canadian Electrical Code, C22.1, Part1.
Full Range Transducer
Ohm
8
70 Hz to 15 kHz
10 – 100 Watts
.28'' Diameter x 2.08'' Height
2
Mounting Plate 3.5'' Diameter
1.2 lb / .54 kg
1480 & 2043
SolidDrive SD1 In-Wall and
In-Ceiling Mounting Bracket Specifications
ype
T
Construction
Dimensions
Weight
WARRANTY
es, SolidDrive subwoofers, and A4 amplifiers are guaranteed for 7 years
iv
SolidDr
from date of purchase. Any misuses or modifications to this equipment in any way will
void the warranty.
ARNING
W
Read instructions prior to operating. To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture. Unplug prior to cleaning and clean with a
damp cloth. There are no user-serviceable parts in this product, please refer all
vicing to qualified personnel.
ser
8650 College Boule
866.663.9770
TEL:
atented balanced cantile
P
vy duty, galv
Hea
12OC – 2.0'' H x 17.5'' W x 5.0'' D
16OC – 2.0'' H x 25.5'' W x 5.0'' D
24OC – 2.0'' H x 13.5''
1.0 lb / .45 kg
vard
AX: 913.663.9790
• F
anized steel
erland Park, KS 66210
• Ov
• www
er spr
v
W x 5.0'' D
.soliddrive.com
ing br
et
k
ac
Experience Audio Perfection
Induction Dynamics extensive line of audio
products makes it easy to create the ultimate
audio system, regardless of installation
requirements. Induction Dynamics builds
these products with only the most select
components and materials; and utilizes
numerous unique and proven technologies.
INSTALLATION OF SOLIDDRIVE SD1 INTO WALLS
AND CEILINGS
By utilizing these basic installation steps, you can install the
SolidDrive SD1 into walls and ceilings to create sound for
boardrooms, home theater, and distributed audio.
GETTING STARTED WITH SOLIDDRIVE
What’s included with the SolidDrive SD1 for installation
into walls and ceilings and what is supplied by the
installer —
A SolidDrive SD1 consists of: One (1) SolidDrive SD1 unit
and attached wiring harness with Eurostyle connector.
*Additional mounting materials may need to be ordered with
the SolidDrive SD1 or supplied by the installer depending on
the application.
For drywall: For in-wall and in-ceiling installation, you will
have ordered one (1) or more SolidDrive SD1s and one (1)
or more patented acoustic in-wall mounting brackets (one (1)
et per SD1), which comes with f
k
ac
br
Phillips flat head machine screws for mounting the drive to the
bracket. At the time of the order, you will also have specified
et(s) in widths of 12OC, 16OC, or 24OC
k
mounting br
(ON CENTER of wall studs or ceiling joists) for proper width.
*Installation also requires f
one (1) container of 3M
by the installer).
EXISTING
For retrofitting the SolidDrive SD1 into existing drywall
installations, it will be necessary to remove a portion of the
xisting dr
e
after the SolidDrive SD1 is installed. Please refer to the
instr
necessary for the type of installation. If installing the
SolidDrive SD1 in new construction, IGNORE the EXISTING
DRYWALL steps.
ac
DR
all bef
yw
uctions mar
our (4) 1 3/8'' dr
®
Super 77 Spray Adhesive (supplied
ALL INSTALLATION NOTE:
YW
ore installation and to replace the drywall
EXISTING
ed with
k
our (4) #8-32 x 5/16''
ws and
all scre
yw
DRYWALL for the steps
STEP 1
INSTALLATION INTO EXISTING DRYWALL
Cut a rectangle opening in the wall
For installing the SolidDrive SD1 mounting bracket into existing drywall, first
cut a rectangular opening in the drywall. The minimum recommended
opening size is approximately fifteen inches tall and beyond the width of the
adjacent wall studs. This will help in attaching the mounting bracket,
feathering the drywall back in, and getting the drywall to meet at the seams
(Figure 1). This will allow proper distribution of sound and the SolidDrive
SD1 will function with optimum performance.
Figure 1
Cut an
opening
large
enough to
install the
mounting
bracket to
the wall
studs
STEP 4
Figure 4 Eurostyle connector
Make the electrical connections
Make the electrical connection
between the SolidDrive SD1 and the
speaker cable using the Eurostyle
connector attached
to the end of the
SolidDrive SD1 audio cable. The
polarity of the wiring is clearly
indicated (Figure 4). NOTE:When
installed in Canada, this product
must be installed in accordance
with the Canadian Electrical Code,
C22.1, Part1.
STEP 5
Apply adhesive to the drywall surface and base of the SolidDrive
If possible, position the SolidDrive SD1 near the center of the drywall panel or
away from the edge of the panel. Prior to mounting, determine the area that
will come in contact with the base of the SolidDrive SD1, and spray that area
liberally with the 3M
on the surface of the oversized mounting base of the SolidDrive SD1 (masking
around the base is recommended to prevent overspray). NOTE: Failure to
apply the adhesive to both the drywall surface and oversized mounting
base will prevent the system from functioning properly.
®
Super 77 contact spray adhesive. Also, spray a thin layer
STEP 2
Attach the SolidDrive mounting bracket to wall studs or
ceiling joists
Place the mounting bracket between the wall studs or ceiling joists and
secure with two 1 3/8" drywall screws. Insert the screws through the two
pre-drilled holes in each flange and screw them into the face of each wall
stud or ceiling joist (Figure 2). The drywall screws need to be driven flush
with the surface of the flange so that the drywall sets flush on the bracket
flange. NOTE: If installing the SD1 in existing drywall using the optional
heat sink, install the SD1 into the mounting bracket as described in step
3 below, then install the heat sink over the SD1 before mounting the
bracket to the studs. To install the heat sink, slide it over the SD1
housing body and tighten with the included mini hex key. DO NOT
OVERTIGHTEN as this could strip the screw.
Figure 2
SolidDrive
SD1
mounting
bracket
attached
to the wall
studs
STEP 3
Insert the SolidDrive into the bracket
Feed the SolidDrive SD1 cable through the round opening in the face of the
mounting bracket. Insert the SolidDrive SD1 through the same opening with
the oversized mounting base facing outward toward the side that the drywall
will be installed and flush against the bracket face. Align the pre-drilled holes
in the mounting base to the threaded holes in the bracket face (Figure 3).
Attach the SolidDrive SD1 securely to the mounting bracket using the 4
Phillips flat head machine screws.
Figure 3
SolidDrive
SD1 being
installed
into the
mounting
bracket
STEP 6
EXISTING DRYWALL
Re-install rectangular cutout in wall
For re-installing the rectangle drywall panel that was cut out to install the
SolidDrive SD1, it is important to create a uniform seal between the cut
drywall and the existing drywall.This will allow proper distribution of sound
and the SolidDrive SD1 will function with optimum performance. Apply fast
setting joint compound, not vinyl based, in the space between the cutout
section and the existing drywall panel. Make sure to fill the space completely
with drywall compound then proceed with the normal taping, sanding and
finishing routine.
STEP 7
Install the new drywall
Immediately install the new drywall before the spray adhesive sets up
(approximately 10 minutes). This allows adjustment of the panel before the
final location is determined. The drywall panel is to be fitted to the wall studs
or ceiling joists and screwed into position. Apply joi
between the drywall panels and proceed with the normal taping, sanding and
finishing routine. The joint compound filled between the panels will improve
the distribution of sound as well as overall sound quality.
nt compound in the space
STEP 8
Equalize the SolidDrive sound system
The surface material plays a key role in the system’s sound performance.
To ensure an optimal listening experience the installer MUST equalize the
SolidDrive SD1 system. Equalization is accomplished by using the optional
SolidDrive Drywall Passive Equalization Module (not UL approved) or using
the auto equalization feature available on some receivers.
Installation is now complete, you can enjoy the audio perfection
of the Induction Dynamics SolidDrive SD1 sound system.
HIGH OUTPUT INSTALLATIONS
For installations requiring high
output, such as a home theater or
other high output type applications,
two SolidDrive SD1’s should be used
for each of the high output channels
(for example the left, right, and center
of a home theater or the left
channel
and right channels of a high output
stereo system). The two SD1’s should
be wired in series for each of the high
output channels (Figure 5). For
maximum output each SolidDrive
channel should have available at
least 20 square feet of surface area.
Figure 5 SolidDrive wired in series
Loading...