Soleus Air WM1-15E-01, WM1-18E-01, WM1-24E-01 Operating Instructions Manual
Models
WM1-15E-01
15,400 BTU
WM1-18E-01
18,300 BTU
WM1-24E-01
24,700 BTU
Electronic Window Air Conditioner
Operating Instructions
V170124
Plug into a grounded 3 prong outlet.
Do not remove the ground prong.
Do not use a plug adapter.
Do not use an extension cord.
Unplug the air conditioner before servicing
Use two or more people to move and install the air
conditioner
This is a safety alert symbol.
This symbol alerts you to potential hazards that can harm you or others or even cause
death.
All safety messages will directly follow the safety alert symbol and/or the words
“DANGER” or “WARNING”.
All Safety messages alert you of potential hazards, how to reduce the chance of injury,
and what can happen if instructions are not followed correctly.
Failure to immediately follow these
instructions may cause serious injury
or even death.
PURCHASE INFORMATION
SAFETY INSTRUCTIONS
Thank you for choosing a Soleus Air Air Conditioner. This owner’s manual will provide you with
valuable information necessary for the proper care and maintenance of your new product. Please take
a few moments to thoroughly read the instructions and familiarize yourself with all the operational
aspects of your new air conditioner.
For your own records, please attach a copy of your sales receipt to this manual. Also, write the store
name/location, date purchased, and serial number below:
Store Name:
Location:
Date Purchased:
Serial Number (located on back of unit):
Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a
safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to
all safety messages outlined in this owner’s manual.
WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow
the following basic precautions:
POWER CORD AND PLUG
This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and
plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord
with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.
The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the risk
of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they must
be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any exposed
metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:
1. Plug power cord into wall outlet. The LED light will turn on.
2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,
the LED light will turn off.
3. Press RESET button to restore power to the machine. Once power is restored, the LED light
will turn on again.
If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air
conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting
recommendations.
LED LIGHT
Note: Your units power cord and plug may differ from the one shown.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
4. The cord and plug are intended for indoor use only.
CURTAIN
CURTAIN LOCK
FOAM SEAL FOR
BOTTOM RAIL
SCREWS AND
LOCKNUTS
FRAME
ASSEMBLY
WINDOW SUPPORT
BRACKET
Weather Insulation Board
SILL ANGLE BRACKET
FLATHEAD BOLT
LOCKNUT
Remote Control
2 AAA Batteries
Owner's Manual
WINDOW SASH SEAL
SASH LOCK AND
SHORT SCREW
FOAM GASKET
TOP MOUNTING
RAIL
SHORT SCREW
TOOLS NEEDED
Large Flathead Screwdriver
Tape Measurer
Adjustable Wrench or Pliers
Pencil
Level
Socket Wrenches
Phillips Head Screwdriver
PACKAGE CONTENTS
Hardware
(in plastic bag)
Qty.
Sash Lock
Screw and
Locknut
Flathead Bolt
and Locknut
Sill Angle
Bracket
Curtain Lock
1
4
2
2
2
Long Screws
13
Short Screws
10
Non-Hardware Part List
Window Air Conditioner (1)
Remote Control (1)
AAA Batteries (2)
Top Mounting Rail (1)
Foam Gasket (1)
Curtain (2)
Window Sash Seal (1)
Foam Seal for Bottom Rail (1)
Owner’s Manual (1)
Weather Insulation Board (2)
Model
WM1-15E-01
Power Supply (Ph/V/Hz)
1/115/60
Rated Cooling Capacity (BTU/h)
15,400
Cooling Power Input (Watts)
1,230
Rated Current Cooling (Amperage)
12
EER
11.8
Noise Level dB(A) (L/H)
55/59
Airflow CFM (H/L)
700/610
Dehumidifying Capacity
74 Pints per day
Product Dimensions (W” x H” x D”)
23.625 x 17.75 x 25.375
Package Dimensions (W” x H” x D”)
26.125 x 20 x 30.5
Net/Gross Weight (Lbs)
110/121
Refrigerant Type
R-410A
Plug Type
NEMA 5-15P
Model
WM1-18E-01
WM1-24E-01
Power Supply (Ph/V/Hz)
208/230/60
208/230/60
Rated Cooling Capacity (BTU/h)
18,300
24,700
Cooling Power Input (Watts)
1,530
2,330
Rated Current Cooling (Amperage)
6.7
10.3
EER
11.8
10.3
Noise Level dB(A) (L/H)
56/61
56/61
Airflow CFM (H/L)
730/630
760/660
Dehumidifying Capacity
83 Pints per day
152 Pints per day
Product Dimensions (W” x H” x D")
26.375 x 18.625 x 26.625
26.375 x 18.625 x 26.625
Package Dimensions (W” x H” x D”)
29.5 x 20.875 X 31.125
29.5 x 20.875 X 31.125
Net/Gross Weight (Lbs)
132/154
141/163
Refrigerant Type
R-410A
R-410A
Plug Type
NEMA 6-15P
NEMA 6-20P
SPECIFICATIONS
Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.
Power consumption is measured when the fan runs at the highest speed setting.
These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.
WARNING:
Avoid fire hazard or electronic shock,
DO NOT use an extension cord or an adapter plug.
DO NOT remove any prong from the power cord.
DO NOT
under any circumstances,
cut, remove, or bypass the
grounding prong!!
Power supply cord with 3-prong grounding
plug and current detection device
ELECTRICAL SAFETY
DISCLAIMER
ALL INFORMATION AND THE TECHNICAL SPECIFI-
CATIONS PRESENTED IN THIS USER’S MANUAL
ARE THE PRESENTATION OF THE MANUFACTURER. SOLEUS N.A HAS NOT CON-DUCTED
INDEPENDENT TEST TO THE INFORMA- TION AND
THE SPECIFICATIONS PRESENTED HEREWITHIN.
Loading...