Soleus Air GPS 2.0 Watch Instruction Manual

GPS 2.0 Watch Instruction Manual

Introduction

Thank you for purchasing the GPS watch. This GPS watch

is

Training features like speed, trip time, laps, etc.

GPS can display your current location

in an electronic map. Watch features include 12/24H Time format, Chronograph, World

time, 5 daily Alarms, 6 Interval Timers, Run and Run Data

m

communicate with

a PC to store and review your performance. This watch

rechargeable battery that can be charged

through USB port of your PC.

Caring for your GPS watch:

Clean your GPS watch

and heart rate monitor with a dampened cloth preferably with

mild deter

gent solution. Wipe dry using a dry cloth. Do not use chemical cleaners and

solvents that may damage plastic components.

Do not store your GPS watch to prolonged exposure to extreme temperatures as this

may result to permanent damage to your unit.

About GPS:

Global Positioning System (GPS) is a satellite-

based navigation system made up of a

network of 24 or more satellites. GPS works best in clear weather condition, anywhere

in the world, 24 hours a day. Tall buildings may interfere with GPS accuracy.

satellite signals are received, the watch will have 2D GPS fixed (Latitude and

Longitude). When 4 or more satellite signals are received, t

he watch will have 3D GPS

Fixed.

Water immersion:

This GPS watch is designed to be water resistant up to 3 ATM. It can resist water

pressure up to 30 meters. After submersion to water, please make sure to wipe dry and

air dry the unit before using or charging.
Caution: This unit is not intended to be use

d while swimming. Prolonged water

submersion may cause electronic shorting in the unit which may cause minor skin burn

or irritation.

packed with personal

odes. This watch can

uses a

When 3

Getting Started

Step 1) Know your watch:

Push button location:

Push button Function:

S1 – Start / Lap /

+

S3 – View / Enter
S5 – Stop / Save /

-

S7 – Mode
S9 – GPS
S11 – Light / Set

Note: Actual color of the watch and artwork may vary from style to style.

Step 2) Charging the Battery:

Charge the unit for about 4.5 hours

before first use. The length of time for a fully

charged battery will last depending on the actual usage. It is recommended to regularly

re-charge your battery every 1-

2 months even if it is not used to maintain good battery

condition.

2.1) Plug your USB PC link cable to your PC

2.2)

Align the charging clip with the contacts on the back of the watch.

2.3) Connect the charging clip securely to the watch.

Note: Please thoroughly dry the charging contacts and surrounding area to ensure

proper electrical contact and prevent corrosion.

When the battery is low,

it is time to charge the GPS watch.

you charge your watch.
Once the battery is full, it will display CHARGE

100% FULL

Battery low condition:

You cannot turn ON

the GPS when the battery is low. The watch will display

LOW

. The battery icon will blink. You need to recharge the battery in order to use the

GPS again.

When the battery is almost low and you still perform your exercise, your data may not

be sav

ed if the battery becomes low. Please make sure the battery have enough

battery power before doing your exercise in order not to lose your data.

When

the battery level becomes very low, the watch will automatica

display (blank-screen).

The possible screen when

.

BATT

lly turn OFF the

Step 3) Acquire Satellite signals:

T

o get the correct time of day and begin using your GPS watch, you have to acquire

GPS signals. It may take few minutes to acquire the satellite

signals.

3.1) Go outside to an open area away from tall buildings

and trees. Orient the GPS

antenna towards the sky for best reception. The antenna is located at the 6 o’clock

position of the watch.
Note:

In order to accurately navigate the GPS, you need to have a good line of

sight to the satellites.

3.2)

Stand still and do not begin moving while performing the following steps until the

GPS signals are already received.

3.3) How to Turn-ON the GPS:

Press S9 to turn ON the GPS. The watch will start

locating the satellites. After receiving the satellite

signals, it will automatically go to

RUN mode and the watch will display “GPS GO” while the “

CHRONO

3.4) How to turn OFF the GPS:

If you wish to turn OFF the GPS,

about 3 seconds and the watch will momentarily display GPS OFF

to Time view.

Note:

When GPS is ON and CHRONO is running or stop, User cannot turn OFF

GPS.

GPS signals and its meaning:

” blinks.

press and hold S9 for

and then return

You will hear

a beep sound when the watch has received a GPS signal or when the

GPS signal has been lost. LOST GPS signal

will also be displayed in the screen.

If no Satellite signal is received within 15 minutes, the watch will auto return to Time

mode.

Step 4) Go for a Run:

4.1) Using Run mode:

4.4.1)

Press S1 or S7 from Time mode to go to RUN mode.

4.4.2) The watch will

automatically search for GPS signal. Once the signal is

received, the watch will prompt “

GPS GO, PACE and the CHRONO time

blinks.

4.4.3) Press S1

to START or TAKE LAP. If auto lap function is set, the watch will

take lap automatically based on auto lap setting.

sound during taking of auto lap.

4.4.4) Press S5

to stop after completing your run.

4.4.5) Press & hold S5 again

to save your run data.

Note:

When the chronograph is stopped or reset, the GPS will automatically turn

OFF after 15 minutes and return to

Time mode.

4.2) Using Chronograph mode:
RUN mode and CHRONOGRAPH

mode has the same timer counter. When the

chronograph is started or stopped in RUN mode, the same thing happens in

Chronograph mode. They just diff

er in the views

chronograph,

lap time, exercise time, and distance travelled.

4.2.1) Press S1

to START or TAKE LAP. If auto lap function is set, the watch will

take lap automatically based on auto lap setting.

sound during taking auto lap.

4.2.2) Press S5

to stop after completing your run.

4.2.3) Press & hold S5

again to save your run data.

Step 5)

Download your data to PC

The watch comes with PC software to make communication between your watch and

PC easy and enjoyable. Please install the PC software to your PC using the installer

provided. The watch is using a USB PC link cable to connect the watch to PC.

And there is a beep

. This mode is dedicated to

There is also a beep

: