Soleus SG004 User Manual

GPS Tour

GPS Tour User Manual

Introduction

Thank you for purchasing the GPS Tour Watch. This GPS Watch is packed with personal
Training features like speed, trip time, laps, etc. Watch features include but not limited to the
following:

! 12/24H Time format
! Chronograph
! World time
! Dual Time T1 and T2
! 5 daily Alarms
! RUN mode
! Chronograph mode
! Timer mode
! HRM mode (2.4GHz)
! Route mode
! Altimeter mode ( GPS based)
! Compass mode ( GPS based)
! Data mode
! Set modes

" This Watch can communicate with a PC to store and review your

performance.

" This Watch uses a rechargeable battery that can be charged through USB

port of your PC.

Caring for your GPS Watch:

Clean your GPS Watch with a dampened cloth preferably with mild detergent solution. Wipe
dry using a dry cloth. Do not use chemical cleaners and solvents that may damage plastic
components.

Do not store your GPS Watch to prolonged exposure to extreme temperatures as this may
result to permanent damage to your unit.

About GPS:

Global Positioning System (GPS) is a satellite- based navigation system made up of a
network of 24 or more satellites. GPS works best in clear weather condition, anywhere in the
world, 24 hours a day. Tall buildings may interfere with GPS accuracy. When 3 satellite
signals are received, the Watch will have 2D GPS fixed (Latitude and Longitude). When 4 or
more satellite signals are received, the Watch will have 3D GPS Fixed.

Water immersion:

This GPS Watch is designed to be water resistant up to 3 ATM. It can resist water pressure
up to 30 meters. After submersion to water, please make sure to wipe dry and air dry the unit
before using or charging.

Caution:

" Prolonged water submersion may cause electronic shorting in the unit which may

cause minor skin burn or irritation.

" Persons who are using Pacemakers should not use this devise with the HRM belt.

Signal from the HRM belt may interfere with the pacemaker.

Getting Started

Step 1) Know your Watch:

Push button location:

Push button Main function:

S1 – Start / Stop / Hold to Save / Increase adjust (+)
S5 – View / OK
S7 – Change Mode / Exit

S11 – Light / Set / Save / Lap / Decrease adjust (-)

GPS Tour

Step 2) Charging the Battery:

Charge the unit for at least 4 to 5 hours before first use. The length of time for a fully charged
battery will last depending on the actual usage. It is recommended to regularly re-charge your
battery every 1-2 months even if it is not used to maintain good battery condition.

2.1) Plug your USB PC link cable to your PC

2.2) Align the charging clip with the contacts on the back of the Watch.

2.3) Connect the charging clip securely to the watch.

Note: Please thoroughly dry the charging contacts and surrounding area to ensure proper
electrical contact and prevent corrosion.

When the battery is low, it is time to charge the watch.

Battery low condition:

You cannot turn ON the GPS when the battery is low. The watch will display LOW BATT. You
need to recharge the battery in order to use the GPS again.

When the battery is almost low and you still perform your exercise, your data may not be
saved. Please make sure the battery have enough battery power before doing your exercise
in order not to lose your data.

Step 3) Configure your Watch:

Before using your watch, you may please set your Watch.

3.1) While in TIME mode, press S7 to go to SET mode and set the following parameters:
AUTO LAP, TIME, UNITS, USER, HRM, HRM LINK, VIEW, NIGHT, Contrast, CHIME,
ALARM, TIMER, and SCALE.

Press S1 or S11 to change the blinking parameter to set.

How to set the AUTOLAP:

• Press S5 while AUTO LAP is blinking. Auto lap 1 will start to blink.

• Press S1/S11 to change the setting. Auto lap preset settings are: off, 0.4, 1, 2, 3, 4,

and 5 KM.

• Press S5/S7 to confirm and set ALERT ON or OFF.

• Press S1/S11 to change the setting. There is a beep sound and EL on for 10 sec every

auto lap taking when ALERT is set to ON.

• Press S5/S7 to confirm setting and go back to Auto lap setting screen.

GPS Tour

How to set the TIME:

TIME 1/ Time 2 setting:

• Press S5 while TIME is blinking. The watch will display T1 or T2.

• Press S1/S11 to choose between T1 or T2 to set.

• Press S5 to set the selected time (T1 or T2). The watch will display GPS or MANUAL.

• Press S1/S11 to select GPS or MANUAL. You have two options in setting the watch,

GPS or MANUAL. In manual setting, you can manually set the time. If you select the
GPS option, the watch will be automatically set based on the data and time data from
GPS satellites.

GPS setting:

o While GPS is blinking, Press S5 to set the TIME ZONE.
o Press S1 or S11 to change the time zone. There are 36 city codes to choose from.
o Press S5 to confirm and set DST ON /OFF.
o Press S1/S11 to change setting.
o Press S5 to confirm and set 12H/ 24H format setting.
o Press S1/S11 to change 12H/24H format setting.
o Press S5 to confirm and go back to TIME setting screen.

MANUAL setting:

o While MANUAL is blinking, Press S5 to enter.
o Set the HOUR by pressing S1 or S11 and then press S5 to enter.
o Set the Minute by pressing S1 or S11 and then press S5 to enter.
o Set the SECOND by pressing S1 or S11 and then press S5 to enter.
o Set the YEAR by pressing S1 or S11 and then press S5 to enter.
o Set the MONTH by pressing S1 or S11 and then press S5 to enter.
o Set the DATE by pressing S1 or S11 and then press S5 to enter.
o Set the 12/24H by pressing S1 or S11 and then press S5 to enter.
o Press S5 to enter.

How to set the UNITS:

• Press S5 while UNIT is blinking. KM will start to blink.

• Press S1/S11 to change the unit.

• Press S5/S7 to confirm setting and go back to UNIT setting screen.

How to set USER details:

• Press S5 while USER is blinking. GENDER will start to blink and 2 seconds later MALE

is blinking.

• Press S1/S11 to change the gender (MALE or FEMALE).

• Press S5/S7 to confirm and set the AGE. Age digits will start to blink.

• Press S1/S11 to change the age digits.

• Press S5/S7 to confirm and set the WEIGHT. Weight digits will start to blink.

• Press S1/S11 to change the weight digits.

• Press S5/S7 to confirm and set the HEIGHT. Height digits will start to blink.

• Press S1/S11 to change the height digits.

• Press S5/S7 to confirm and go back to USER setting screen.

Note: While in USER GENDER, USER AGE, USER WEIGHT or USER HEIGHT
screen, press S1 to toggle.

GPS Tour

How to set the HRM:

• Press S5 while HRM is blinking. ZONE 1 will start to blink.

• Press S1/S11 to change the zone. There are 3 preset zones

• Press S5 and the watch will display the LOWER limits of the selected zone. LOW limit

digit will start to blink.

• Press S1/S11 to change the low limit value.

• Press S5 to confirm. High limit digit will start to blink.

• Press S1/S11 to change the high limit value.

• Press S5 to confirm. The watch will display ZONE ALERT ON or OFF.

• Press S1/S11 to change ON to OFF or vice versa

• Press S5 to confirm and the watch will go back to HRM setting screen.

o Max HRM calculation: 220 – Age
o HR Zones: 1, 2, 3
o Low Limit setting range: 30 BPM to HIGH limit value
o High limit setting range: Low limit value to 240 BPM

How to link the HRM belt to the Watch:

This is where you LINK your HR belt to the GPS watch

• Press S5 while HRM LINK is blinking. Make sure you are properly wearing the HRM
belt on your chest. The watch will start to search for the HRM signal from the HRM belt.

• Within 1 minute of searching, the watch will display your Heart Rate and % Max.

• The watch will automatically go to HRM mode.

• If the LINK fails, it will display FAIL. Please try linking again.

How to set the VIEW (2 rows or 3 rows)

• Press S5 while VIEW is blinking. View “3” digit will start to blink.

• Press S1/S11 to select VIEW setting “2 or 3 row”.

You can select what information to display in Line 1 & Line 3 for 3-row display and Line 2
for 2-row display as shown.

How to set the LCD display CONTRAST:

• Press S5 while CONTRAST is blinking. Contrast percentage will start to blink.

• Press S1/S11 to change to your desired value. LCD Contrast range is from 10 to 100%.

• Press S5/S7 to exit to CONTRAST setting screen

Contrast range = 10 to 100%

GPS Tour

How to set the NIGHT mode function:

• Press S5 while NIGHT is blinking. The watch will display 10 seconds blinking.

• Press S1/S5 to change to 20 sec or NIGHT ON.

• While on 10 SEC or 20 SEC setting, Press S5 to accept the setting and go back to

NIGHT setting screen.

• While on NIGHT ON setting screen Press S5 to accept the ON setting. The watch will
display the START TIME.

• Press S1/S11 to toggle between START TIME and END TIME.

• Press S5 or 3 seconds auto to set the START TIME. Hour digit will start to blink.

• Press S1/S11 to change the hour setting.

• Press S5 to change the MINUTE. Minute digits will start to blink.

• Press S1/S11 to change the minute setting.

• Press S5 to go back to START TIME setting screen.

• Press S1/S11 to set the END TIME. Hour digit will start to blink.

Note: Follow the procedure in setting the START TIME.

• Press S7 to exit to NIGHT ON setting screen.

Night mode settings:

• 10 SECONDS – Press S11 will turn ON the Light for 10 seconds.

• 20 SECONDS – Press S11 will turn ON the Light for 20 seconds.

• NIGHT ON – Light will continuously ON when CHRONO is running in preset duration time

(5:00 pm to 7:00 am). Start and End time can also be manually set to different times.

How to set the CHIME:

• Press S5while CHIME is blinking. The watch will display CHIME ON.

• Press S1/S11 to change to CHIME OFF or OFF.

• Press S5/S7 to confirm and exit to CHIME setting screen

How to set the ALARM:

• Press S5 while ALARM is blinking. AL-1 will start to blink.

• Press S1/S1 to toggle through Alarm 1 to alarm 5. The watch has 5 alarms which can be

set individually

• Press S5 to set the selected Alarm. The HOUR digit will start to blink.

• Press S1/S11 to change the hour digit.

• Press S5 to confirm and set the MINUTE digit. The minute digit starts to blink.

• Press S1/S11 to change the minute digit.

• Press S5 to confirm and set the T1 or T2 setting. T1 or T2 starts to blink. The alarm time

will be referred to Time 1 or Time 2.

• Press S1/S11 to change setting

• Press S5 to confirm. Alarm ON or OFF will start to blink.

• Press S1/S11 to change the setting.

• Press S5 to confirm and go back to ALARM 1 setting screen

• Press S7 to exit.

GPS Tour

How to set the TIMER:

• Press S5 while TIMER is blinking. The segment number will start to blink.

• Press S1/S11 to change the segment number

• Press S5 to set the HOUR. The hour digit starts to blink.

• Press S1/S11 to change the digits

• Press S5 to set the MINUTE. The minute digit starts to blink.

• Press S1/S11 to change the digits

• Press S5 to set the SECONDS. The second digit starts to blink.

• Press S1/S11 to zero the digits.

• Press S7to exit TIMER setting screen

How to set the SCALE:

• Press S5while SCALE is blinking. The watch will display SCALE AUTO.

• Press S1/S11 to change the scale.

• Press S5/S7 to confirm and exit scale setting screen.

Scale range: AUTO, 50 M, 100 M, 200 M, 400 M, 800 M, 1.6 KM, 3.2 KM, 6.4 KM

3.2) TIME, NIGHT, CONTRAST, & CHIME, can also be set in TIME quick SET mode.

• Press and hold S11 while in Time mode. TIME will start to blink.

• Press S1/S11 to toggle through TIME, NIGHT, CONTRAST and CHIME.

3.3) AUTO LAP, UNITS, USER, and VIEW can also be set in RUN quick SET mode.

• Press and hold S11 until AUTO LAP blinks.

• Press S1/S11 to toggle through AUTO LAP, UNIT, USER and VIEW.

GPS Tour

3.4) TIMER can also be set in TIMER SET mode

• Press and hold S11 until SG 1 (segment 1) blinks.

• Press S5 to set the hour, minute and second.

3.5) HRM and LINK HRM can also be set in HRM quick SET mode.

• Press and hold S11 until HRM LINK blinks.

• Press S5 to enter HRM link. It will then start to search (within 1 min.) for HR belt

and once HRM linked is successful it will display the HR belt ID number. If HRM link
fails, after 1 minute of searching, the watch will display “HRM LINK FAIL”

3.6) ALARM can also be set in ALARM quick SET mode.

• Press and hold S11 until the “ALARM” blinks.

• Press S5 to set the alarm 1 to 5, hour, minute, T1/T2 and Alarm On/Off.

Note: The Chime can also be set. When Chime is on, there will be an hourly chime.

GPS Tour

Step 4) Acquire Satellite signals:

In order to get the correct time of day and begin using your watch, you have to acquire the
Satellite signals. It may take a few minutes to get the signals.

4.1) Go outside to an open area away from tall buildings and trees. Orient the GPS antenna
towards the sky for best reception. The antenna is located at the 12 o’clock position of
the watch.

4.2) Stand still and do not begin moving while locating the Satellites until the GPS signals are
already received.

4.3) How to Turn ON the GPS: Following are the possible ways to turn on the GPS.

4.3.1) Press S1 in TIME mode. The Watch will display the GPS / INDOOR selection

screen.

4.3.2) Press S7 to go to exercise modes enter RUN, CHRONO, HRM, ROUTE, ALTI,

COMPASS, or TIMER mode.

4.3.3) Press and hold S7 for 2 seconds from any mode while GPS is initially OFF.

4.4) How to turn OFF the GPS:

4.4.1) Press and hold S7 for 2-3 seconds from any mode while GPS is initially ON.

4.4.2) Press S7 to enter RUN, CHRONO, HRM, ALTI, COMPASS, or TIMER mode.