Soleus LS14121430 Specs

MINI SPLIT LINE SETS SPECIFICATIONS

MODEL # FITS MINI

SPLIT
MODEL

LS14381415 RAS-09

KFR-09

LS14381430 RAS-09

KFR-09

LS14121415 KFS-12

KFR-12
KFR-18
KFI-09
KFH-12
KFIHP-09
KFHHP-12
KFGHP-09
KFGHP-12

LS14121430 KFS-12

KFR-12
KFR-18
KFI-09
KFH-12
KFIHP-09
KFHHP-12
KFGHP-09
KFGHP-12

LS38581415 KFR-24

KFH-18
KFHHP-18
KFHHP-22
KFGHP-18
KFGHP-24

LS38581430 KFR-24

KFH-18
KFHHP-18
KFHHP-22
KFGHP-18
KFGHP-24

DESCRIPTION
L=Liquid
S=Suction
W=Wall

1/4”L x 3/8”S x ¼” W 15 4.5

1/4”L x 3/8”S x ¼” W 30 9

1/4”L x ½”S x ¼” W 15 5.5

1/4”L x ½”S x ¼” W 30 11

3/8”L x 5/8”S x ¼” W 15 8.5

3/8”L x 5/8”S x ¼” W 30 16

LENGTH SHIPPING

WEIGHT

Note: These are copper line sets both liquid & suction lines
insulated with ¼’ rubber insulation tubing suitable for DX and/or
heat pump. Each end has female flare connectors attached.

Soleus International Inc.

9451 Telstar Avenue El Monte, CA 91731

www.soleusair.com

TECHNICAL BULLETIN

LINE SET OUTDOOR APPLICATIONS

Use of Soleusair’s flexible rubber insulation [contained on our copper line sets] product outdoors may
require special installation recommendations to prevent unacceptable degradation from ultra-violet (UV)
exposure.

Soleusair’s rubber insulation is produced from UV resistant materials. For
applications such as residential, no additional protective coating or jacketing is required for many years of
service. However, for
required, it is recommended that the insulation be coated with a protective coating material or jacketing as
required for the conditions.

It is difficult to determine outdoor service life of the rubber insulation due to the wide range of
environmental conditions that may be encountered. In addition to the harmful rays of the sun, other
factors such as damage from maintenance workers, wildlife and weather conditions must also be factor ed
in. Protective coating/ jacketing provide more than just protection from UV degradation.

Accelerated UV aging studies are difficult to correlate to actual outdoor exposure because of the wide
range of potential exposures for various applications and in different parts of planet Earth. In addition,
there are no industry accepted performance criteria by which to determine if a product is meeting
expectation or not. As such, Soleusair is not able to provide any type of specific life expectancy for our
products when used outdoors.

Some states (CA, TX, FL, etc) have recently made changes to their building codes as a result in mandates
to improve energy savings, revising wall thickness requirements for some applications from 3/8” to ¾” or
even 1” on some outdoor applications. These changes are state by state and in some cases even dictated at
the local level. The codes have always stated that outdoor applications require the material to be protected
from UV exposure. Some of the new codes now state: “should be protected from UV exposure unless the
product is produced from UV resistant material”. This new wording poses a major problem in that the
term “UV resistant material” is not defined. It is similar to the terms biodegradable or hypo-allergenic.
Without specific definition or test methods, these terms are practically useless. As a result, Soleusair is
reluctant to put the term “UV resistant” on its insulation because of the potential for misunderstanding. In
some application (as noted above) the product will perform to typical expectation but in severe UV
exposure applications or where other factors may enter into the conditions the product will be exposed to,
it may not perform to expectation unless it is protected.

Soleusair feels it is better to provide a conservative recommendation along with information on which our
customers can make an informed decision.

severe UV exposure [roof top applications] or where optimum performance is

052307

moderate UV exposure

Tel: [phone] Fax: [phone]