LED Crystal Ball
REMOTE CONTROL DMX512 CRYSTAL BALL LED LIGHT
User's Manual
Read this manual before using. Do not attempt to open the housing or repair
this device by yourself without contact us!
General
instructions
Troubleshooting
1. If the power supply indicator doesn't light up and the light doesn't work, please
1PCS
Unpacking: check the power supply, the input voltage and the fuse.
Thank you for purchasing this product. Please read user guide for safety and before using
the product. Keep this manual for future reference. This product can create perfect light
programs and effects since it has passed a series of strictly tests before delivery. Please check
the attachments listed on the page after opening the carton. Immediately upon receiving
a fixture, carefully unpack the box. Check the box contents to ensure that all parts are present
and that they are in good condition. If any part appears damaged from shipping, or if the
box shows signs of mishandling, notify the shipper immediately. In addition, retain the box 3. In Master-Slave operation, slave unit don't function, please check as below.
and all the packing material for inspection.In any event, save the carton and all packing material
because, in case that you have to return the fixture to the factory, you will have to do so in its
original box, with its original packing.
1. LED Light:
2. Power Cable: 1PCS 3. User Guide: 1PCS
Safty Notice:
Please read the following notes carefully because they include important safety information
about the installation,usage and maintenance of this product. It is important to read all these
notes before starting to work with this product.
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to
the
acceleration of this decline. Packaged in clusters, LEDs exhibit higher operating
temperatures than in ideal or singular optimum conditions. For this reason when all color
LEDs are used at their fullest intensity, life of the LEDs is significantly reduced. It is
estimated that a viable lifespan of 40,000 to 50,000 hours will be achieved under normal
operational conditions. If improving on this lifespan expectancy is of a higher priority,
place care in providing for lower operational temperatures. This may include climatic-
2. In Stand-Alone operation, if the power supply indicator is light up and sound
active indicator isn't light up, but the light is shut off doesn't work.
A. Because sound is too small make for light shut off in sound active, please
increase the music volume or increase audio sensitivity with sensitivity knob,
please check as below.
B. Please check if unit has been set up in slave mode, then set up in master mode.
A. Make sure to there's only one master in the chain, and the others are set in slave mode.
B. Make sure to control the unit without DMX console controlling.
C. Make sure to take a good quality power cable and connection.
Warranty Warnings:
1. Damages caused by the disregard of this user manual are not subject to Warranty.
The dealer will not accept liability for any resulting defects or problems.
2. Please consider that unauthorized modifications on the device are forbidden due to
safety reasons. Please note that damages caused by manual modifications on the
device or unauthorized operation by unqualified persons are not subject to warranty.
3. If this device will be operated in any way different to the one described in this
manual, it may suffer damages and the guarantee becomes void. Furthermore, any
other operation may lead to dangers like short-circuit, burns electric shock, etc.
After trying the above solution you still have a problem, please contact your dealer
or our company for service.
Page 1 Page 10
IR control Introduction
Technical
Specification
Function:
1.the user can choose the voice control, automatic work mode, DMX512 work mode with remote
control.
2.Under remote control mode, the remote controller works like a MINI DMX512 controller, can
manually adjust the brightness of the color and control jumping, frequently flashing, rotating,
movement, zoom(+/-). Speed is adjustable
3.Remote control distance is up to 8 Meters
Precautions
A. Using infrared remote controller to control the machine running, the launch of the infrared
remote controller must on the machine head of infrared receiving head.
B. Infrared remote controller to control the machine run, infrared emission head sent via infrared
data, if the machine can receive data correctly, LED digital display will flash once, if not Please
check The launch of the infrared remote controller whether on the machine head of infrared
receiving head.
AUTO mode
Slave function
Remote function
DMX IN
Color change
Down/decrease
Flash mode
UP/ increase
Speed control
Feature:
◆With the newest LED technology, this LED light can creat an amazing and romantic
lighting effects for your place.
◆It has over 200 beams of LED lighting from the transparent case. The beams on the wall
looks like handreds of flowers drifting round and round.
◆Compact and lightweight, exquisite appearance, small size, streamline design, attractive
effects.
◆Clear and sharp lighting effects even without fog/smoke
◆Easy to use, plug and play
◆LCD digital display, manual function: color selection, jumping, dimmer, strobe, Sound
Active
◆Stable working, no hassle on warranty
◆Automatic rotation once power on
◆Built-in microphone can trigger external sound
◆DMX control function: 1. color change 2.strobe speed 3. brightness dimming 4.rotation
direction 5. rotation speed 6. Sound active
◆Remote control
Specification:
◆LED power output: 6x1W (Red:1W*2,Green:1W*2,Blue:1W*2)
◆long life working hours:20000 H
◆Rotation angle: 180°
◆Cooling system: air cool
◆Working environment temperature: 0℃-40℃
◆Operation Modes: AUTO, Sound, DMX, Master/Slave, Remote control
◆DMX Channel: 9
◆Input Voltage: 90V-240V AC 50-60Hz
◆LED Light size: 185*185*150mm
◆Net weight: 0.5Kg
◆Gross Weight: 0.8Kg
◆Volume weight: 1.6kg(/5000) on inner gift box, 23.6kg(/5000) on outer carton box.
◆Gift box size: 190*190*160(0.006m³)
Fade mode
Page 9 Page 2
Fixture
Apperance
Front Panel Figure mode, the light beam ON /OFF, running direction, running speed and twinkle speed etc.
8
8
6
1
2 3
4
5
Rear Panel Figure
7
9
10
Remote control distance is
up to 8 Meters
1. working mode selection 2. UP (previous or speedy) 2. DOWN (next or slower)
4. Enter for confirmation 5. Built-in Michrophone 6.Digital LCD display
7. DMX IN 8. DMX OUT 9. Fuse
10. Power Cable
DMX Control
The system only accepts the DMX512 signal of international standard to control the system
DMX Control:
The LED light only accepts the DMX512 signal of international standard to control the light.
DMX Control Parameter Chart
Channel Function Value Description
0～63
CH1
CH2
CH3 Green brightness 0～255
CH4
CH5
CH6
CH7
CH8
CH9
Mode
Red brightness
Blue brightness
LED color
control
LED Strobe
LED fade
Motor spin
control
Motor spin speed
64～127
128～191
192～255
0～255
0～255
0～31
32～63
63～127
128～191
192～223
224～239
240～255
0～63
64～191
192～255
0～15
16～223
224～255
0～95
96～255
0～255
Close, LED OFF
Sound active mode
AUTO mode
DMX mode
dim ----bright
dim ----bright
dim ----bright
R-G-B-RG-RB-GB-RGB color selection
R--G--B AUTO color change
RG--RB--GB color change
R--G--B--RG--RB--GB--RGB AUTO color change
R--G--B Sound color change
RG--RB--GB Sound color change
R--G--B--RG--RB--GB--RGB Sound color change
No strobe
AUTO strobe
Sound Strobe
No fade
AUTO fade
Sound Fade
No spin
Spin
Slow --- Fast
Page 3
Page
4 Digits to display 7 levels functions:
Function
&
Setting
7
Digital display
Description
Red Brightness: 1st digit stands for "Red", 2nd
and 3rd digits stands for levels from 00 to 31, 4th
digit stands for 9 levels motor spin speed
Green Brightness: 1st digit stands for "Red", 2nd
and 3rd digits stands for levels from 00 to 31, 4th
digit stands for 9 levels motor spin speed
Sound Active
The change of the light pattern is controlled by sound, that is, the rhythm of the sound
control the effect of the changing light pattern. Turning the sensitivity knob in the
clockwise direction to increase the fixture’s sensitivity to sound, the knob in the counter
clockwise direction to decrease. The light diode will automatically turn off after 8
seconds when the music stops.
AUTO display lighting effects: 1st digit stands
for AUTO, 2nd and 3rd digits stands for 11
kinds of effects, 4th digit stands for 9 levels of
motor spin speed.
01: Red AUTO Strobe
02: Green AUTO Strobe
03: Blue AUTO Strobe
04: RG AUTO Strobe
05: RB AUTO
Blue Brightness: 1st digit stands for "Red", 2nd
and 3rd digits stands for levels from 00 to 31, 4th
digit stands for 9 levels motor spin speed
Sound Active display lighting effects: 1st
digit stands for SOUND, 2nd and 3rd digits
stands for 11 kinds of effects, 4th digit
stands for 9 levels of motor spin speed.
01: Red SOUND Strobe
02: Green SOUND Strobe
03: Blue SOUND Strobe
04: RG SOUND Strobe
AUTO
Auto cycles the built-in programs without being controlled externally. It has no light OFF.
The mode allows a single unit to react to the beat of the music in the master mode.
1. Install the units in a suitable position (laying or appending).
2. Set dipswitch to select Sound Active or AUTO mode.
3. Turn on the unit power, the unit begins reset, then the unit begins working.
4. The unit will react to the low frequencies of music via the internal microphone.
Adjust the audio sensitivity knob on the back of the unit to make the unit more or less
sensitive in sound active.The panel has LED indicating for sound active.
Master-Slave Operation
This mode will allow you to link up to 32 units together without controller.
1. Install the units in a suitable position (laying or appending).
2. Choose a unit to function as Master mode, set dipswitch to select Sound Active or
AUTO mode. The others must be set to Slave mode, set dipswitch to select Slave mode.
3. Use standard XLR microphone cable chain your units together via the XLR connector
on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
DMX512 mode: 001---512 stands for value
Slave mode
Page
Page 4
Caution:
LCD
Digital
display
function:
Grounding the common can cause a ground loop, and your fixture may perform erratically.
Test cables with an ohm meter to verify correct polarity and to make sure the pins are
not grounded or shorted to the shild or each other.
4. Turn on the all units' power, the units begins reset, then the unit begins working.
The slave units will react the same as the master unit.
5. The units will react to the low frequencies of music via the internal microphone.
Adjust the audio sensitivity knob on the back of the master unit to make the unit more
or less sensitive in sound active.The panel has LED indicating for sound active.
Universal DMX Operation (DMX mode)
This mode allows you to use universal DMX-512 console to operate.
1. Install the units in a suitable position (laying or appending).
2. Use standard XLR microphone cable chain your units together via the XLR connector
on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.
3. Assign a DMX address to each the unit using dipswitches, see the "DMX Address
Quick Reference Char".
Do not allow contact between the common and the ficture's chassis ground.
Menu: function selection
UP/DOWN: LED brightness adjustment, or
DMX512 address value, or lighting effects under
Auto and Sound Active mode
ENTER: Step motor speed level
Light No 1
DMX Signal
1：MASTER: SOUND/AUTO/DMX
4. Turn on the all units' power, the units begins reset, then the unit begins working.
5. Use DMX console to control your units.
Notes:
1. DMX console can not be used in Master-Slave operation (Sound Active or AUTO mode ).
2. There should be only one master unit in Master-Slave operation.
Light No 2
2：SLAVE
Page 5 Page 6
Light No 3
2：SLAVE
Light No ….
……...
Quick Operation:
MENU: Red, green, blue LED brightness, AUTO, Sound Active, DMX512, Master/Slave.
UP/DOWN: Red, green, blue LED brightness adjustment in 32 levels; DMX512 address value;
Lighting effects on AUTO and Sound Active
ENTER: 9 levels on step motor spin speed
Loading...