Sole Fitness TT9 Owner's Manual
TABLE OF
CONTENTS
Product Registration 1
Important Safety Instructions 2
Important Electrical Information 3
Important Operation Instructions 4
Assembly instructions 9
Transport Instructions 13
Operation of Your New Treadmill 14
General Maintenance 36
Service Checklist - Diagnosis Guide 39
Manufacturer’s Limited Warranty 40
Before returning your Sole product to any retailer, or if you require an
assistance with assembly or technical support please call us first for
assistance at 866-697-6531. Thank you for your Sole purchase.
y
TT9 -2018 Ver. A
TT9
TREADMILL
1
CONGRATULATIONS ON YOUR NEW TREADMILL AND WELCOME TO THE SOLE FAMILY!
Thank you for your purchase of this quality treadmill from
one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive
warranties available.
many years to come.
If you have any questions about your new product contact
technical problem with your new treadmill contact
SOLE
will do all we can to make your ownership experience as pleasant as possible for
SOLE
. Your new treadmill has been manufactured by
SOLE
SOLE
technical service at
Fitness at
866-780-SOLE (7653)
866-MYSOLE1 (1-866-697-6531).
. If you have a
Please take a moment at this time to record below the name of the dealer, their telephone number, and the
date of purchase for easy contact in the future. We appreciate your confidence in SOLE
remember that you are the reason that we are in business. Please complete and mail your registration card
today and enjoy your new treadmill.
and we will always
Yours in Health,
SOLE Fitness
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT
RECORD YOUR SERIAL NUMBER Please record the
Serial Number of this fitness product in the space
provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soletreadmills.com under the support tab to register online.
REGISTRATION
TT9_ 201802
TT9 TREADMILL
2
IMPORTANT
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your SOLE treadmill from the electrical
outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the
treadmill on a flat level surface with access to a 120-volt, 15-amp grounded outlet with only the
treadmill plugged into the circuit.
SAFETY
INSTRUCTIONS
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING
IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET.
A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions, page 3.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both
carpet and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
Keep children under the age of 13 away from this machine. There are obvious pinch
points and other caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not
working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, remove tether cord, then remove the
plug from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use
on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
This appliance is not intended for use by persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
TT9
TREADMILL
3
IMPORTANT
ELECTRICAL
INSTRUCTIONS
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any
appliance with a large motor, the GFCI will trip often. Route the power cord away from any
moving part of the treadmill including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your treadmill may be
affected. Such conditions are not covered under your warranty. If you suspect the voltage is
low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment. The maximum operating
temperature specification is 40 degrees c, and humidity is 95% non-condensing (no water drops
forming on surfaces).
Circuit Breakers: Some circuit breakers used in homes are not rated for high inrush currents ,
(ARC fault breakers are one example) that can occur when a treadmill is first turned on or even
during use. If your treadmill is tripping the house circuit breaker (even though it is the proper
current rating) but the circuit breaker on the treadmill itself does not trip, you will need to replace
the home breaker with a high inrush type. This is not a warranty defect. This is a condition we as a
manufacture have no ability to control. This part is available through most electrical supply stores.
Examples:
Grainger part # 1D237, or available online at www.squared.com part # QO120HM.
GROUNDING
This product must be grounded. If the treadmill should malfunction or breakdown, ground
provides a path of least resistance for electric current, reducing the risk of electric shock. This
product is equipped with a cord having an equipment-grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the
product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available. The temporary adapter should be used only until a properly grounded
outlet, (shown below) can be installed by a qualified electrician. The green colored rigid earlug, or the like, extending
from the adapter, must be
connected to a permanent
ground such as a properly
grounded outlet box cover.
Whenever the adapter is
used, it must be held in
place by a metal screw.
INSTRUCTIONS
ing
TT9 TREADMILL
4
IMPORTANT
NEVER operate this treadmill without reading and completely understanding the results of
any operational change you request from the computer.
Understand that changes in speed and grade do not occur immediately. Set your desired
speed on the computer console and release the adjustment key. The computer will obey the
command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your household
power supply that could damage treadmill components. Unplug the treadmill during an
electrical storm as a precaution.
Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or stray
from walking in the center of the belt; which may result in serious injury.
NEVER mount or dismount the treadmill while the belt is moving. SOLE treadmills start at a
very low speed and it is unnecessary to straddle the belt during start up. Simply standing on
the belt during slow acceleration is proper after you have learned to operate the unit.
Always hold on to a handrail or hand bar while making control changes (grade, speed, etc.).
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure. Pushing harder is not going to make the unit go faster or
slower. If you feel the buttons are not functioning properly with normal pressure contact
your SOLE dealer.
OPERATION
INSTRUCTIONS
IMPORTANT
A safety tether cord is provided with this unit and should be used at all times. It is for your safety
should you fall or move too far back on the tread-belt. Pulling this safety tether cord will stop
tread-belt movement.
To Use:
1. Place the safety key into position on the console control head. Your treadmill will not start
and operate without this. Removing the safety key also secures the treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power.
Note: The clip should be attached securely to make certain it does not come off. Be familiar
with its function and limitations. The treadmill will stop, depending on speed, with a one to two
step coast anytime the safety key is pulled off the console. Use the red Stop switch in normal
operation.
SAFETY
INSTRUCTIONS
TT9
TREADMILL
5
IMPORTANT
SAFETY
INSTRUCTIONS
READ BEFORE UNPACKING YOUR FOLDING TREADMILL
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill from
unfolding accidentally during shipping. If this strap is not removed properly the treadmill could
spring open unexpectedly and cause injury if someone is standing near the treadmill when the
strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure the
treadmill is positioned flat on the ground, in the orientation it would be in if you were using the
treadmill. Do not turn the treadmill up on its side while removing the shipping strap. This could
cause the treadmill’s folding mechanism to spring open. If the end of the Velcro strap (that you
need to grab to remove it) happens to be under the treadmill deck, reach under the deck to
grab it, but do not tilt the treadmill up to gain access to the strap end.
PREVENTATIVE
Vacuum Under
Motor Cover &
Check Wiring
(Every Other
Month)
Clean & Inspect Deck
for Lubrication
(Every Other Month)
MAINTENANCE CHART
Lubricate Deck
(Every 90 hours
or sooner if dry)
Inspect Belt Tracking
(Monthly) Adjust if
necessary
Date
TT9 TREADMILL
6
TT9
ASSEMBLY PACK CHECKLIST
1
HARDWARE
#117. Ø10 × 2.0T_
Split Washer (10 pcs)
#134. M5 × 12L_Phillips
Head Screw (4 pcs)
STEP 1
#116. Ø3/8" × 35 × 2T_
Flat Washer (10 pcs)
#193. 3.5 × 12m/m_
Sheet Metal Screw (4 pcs)
HARDWARE
2
#144. 3/8" × 16 × 3"_Button
Head Socket Bolt (10 pcs)
STEP 2
#133. M5 × 20L_
Phillips Head Screw (4 pcs)
TT9
TREADMILL
7
HARDWARE
STEP 3
3
#117. Ø10 × 2.0T_
Split Washer (6 pcs)
#145. 3/8" × 16 × 3/4"_
Button Head Socket Bolt (6 pcs)
#125. Ø3/8" × 25 × 2T_
Flat Washer (6 pcs)
#146. M8 × 1.25 × 12L_
Socket Head Cap Bolt (6 pcs)
4
HARDWARE
#162. 3/8" × 16 × 1-3/4"_
Button Head Socket Bolt (2 pcs)
#163. Ø10 × 23 × 1.5T_
Curved Washer (2 pcs)
STEP 4
#117. Ø10 × 2.0T_
Split Washer (2 pcs)
#134. M5 × 12L_
Phillips Head Screw (8 pcs)
TT9 TREADMILL
8
ASSEMBLY
#148. 8m/m_L Allen Wrench
TOOLS
#147. Phillips Head Screw Driver
#149. 3/8" L Allen Wrench
TT9
TREADMILL
9
TT9
STEP
1
ASSEMBLY
INSTRUCTIONS
1
ASSEMBLY
STEP 1
1. Right Upright(34) which Computer Cable (Lower) (42)
Computer Cable (Lower) (72) already inserted, Move Right
Upright to Main Frame , When align Right Upright and Main
Frame insert the Computer Cable (Lower) (42)、Computer Cable
(Lower) (72) carefully to avoid Computer Cable (Lower) (42)
Computer Cable (Lower) (72) clamp to Right Upright (34) and
Main Frame, Align Foam Pad (98) with Right Upright (34) and
Main Frame , Align one 3/8" × 16 × 3"_Button Head Socket Bolt
(144) with Ø10 × 2.0T_Split Washer (117) and Ø3/8" × 35 ×
2T_Flat Washer (116) then screw up Right Upright (34) and Main
Frame from middle hole on Foam Pad (98). Then screw up other
four 3/8" × 16 × 3"_Button Head Socket Bolt (144), Ø10 ×
2.0T_Split Washer (117) and Ø3/8" × 35 × 2T_Flat Washer (116) .
2. Assemble Left Upright (33) like Right Upright (34)
3. Screw up Motor Base Cap (R) (27) and Motor Base Cap (L) (26)
with four M5 × 12L_Phillips Head Screw (134)
4. Screw up Motor Base Cap (R) (197) and Motor Base Cap (L) (196)
with four 3.5 × 12m/m_Sheet Metal Screw (193)
、
、
HARDWARE
#116. Ø3/8" × 35 × 2T_
Flat Washer (10 pcs)
#117. Ø10 × 2.0T_
Split Washer (10 pcs)
#134. M5 ×12L_Phillips
Head Screw (4 pcs)
#144. 3/8" × 16 ×
3"_Button Head Socket
Bolt (10 pcs)
#193. 3.5 × 12m/m_
Sheet Metal Screw
(4 pcs)
TT9 TREADMILL
10
2
ASSEMBLY
STEP 2
1. Connect Ground Wire(35) and Handpulse Wire (Upper/Lower)(39)
and Computer Cable (Upper)(41) and Pad/Backlit Cable(43) and
Connecting Cable(61) and Computer Cable (Upper)(71) all connect
to the board on back of the console (28).
2. Use four M5 × 20L_Phillips Head Screws (133) to secure console
assembly onto the console support (5).
.
HARDWARE STEP 2
#133. M5 × 20L_
Phillips Head Screw
(4 pcs)
TT9
TREADMILL
11
3
ASSEMBLY
STEP 3
Use six M8 × 1.25 × 12L_Socket Head Cap Bolts (146) to secure the
1.
console on interface mounting bracket on uprights (3, 4).
2. Connect upper computer cable (41) and lower computer cable (42).
Connect upper computer cable (71) and lower computer cable (72)
3. Use six 3/8"x16 × 3/4"_Button Head Socket Bolts (145), together
with six Ø10×2.0T_Split Washers (117) and six 3/8" × 25 × 2T_Flat
Washers (125) on top of uprights. Be careful not to pinch the
computer cable.
HARDWARE STEP 3
#117. Ø10 × 2.0T_
Split Washer (6 pcs)
#125. Ø3/8" × 25 × 2T_
Flat Washer (6 pcs)
#145. 3/8" × 16 × 3/4"_
Button Head Socket
Bolt (6 pcs)
#146. M8 × 1.25 × 12L_
Socket Head Cap Bolt
(6 pcs)
TT9 TREADMILL
12
IMPORTANT ASSEMBLY INSTRUCTION
When assembling the console mounting interface brackets (Items 3&4) please
be sure to slide the brackets all the way towards the back of the console before
tightening the bolts.
Loading...