Sole Fitness E35, E75, E95 Owner's Manual
!
Z100 / Z300
E35
Elliptical
Z500
E75
Elliptical
Z700
E95
Elliptical
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL
Table of Contents
A
A
Product Registration…………………………………………………………………………. 2
Important Safety Instructions………………………………………………………………… 3
Important Electrical Information………………………………………………………………4
Important Operation Instructions……………………………………………………………..4
Assembly Instructions………………………………………………………………………….5
Features……………………………………………………………………………………….. 14
Operation of Your New Elliptical……………………………………………………………...15
Manufacturer’s Limited Warranty……………………………………………………………..32
TTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY
ND IS WARRANTED FOR THA T APPLICATION. ANY OTHER APPLICA TION
VOIDS THIS WARRANTY IN ITS ENTIRETY.
E35 / E75 / E95 Elliptical
1
!
CONGRATULATIONS ON YOUR
NEW ELLIPTICAL AND WELCOME
TO THE SOLE FAMILY
Thank you for your purchase of this quality elliptical trainer from Sole. Your new
elliptical was manufactured by one of the leading fitness manufacturers in the
world and is backed by one of the most comprehensive warranties available.
Through your dealer, Sole will do all we can to make your ownership experience
as pleasant as possible for many years to come. The local dealership where you
purchased this elliptical is your administrator for all Sole warranty and service
needs. Their responsibility is to provide you with the technical knowledge and
service personnel to make your experience more informed and any difficulties
easier to remedy.
Please take a moment at this time to record the name of the dealer, their
telephone number, and the date of purchase below to make any future, needed
contact easy. We appreciate your support and we will always remember that you
are the reason that we are in business. Please complete and mail your
registration card today and enjoy your new elliptical.
Yours in Health,
Sole Manufacturing, Inc.
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
Product Registration
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Sole. or visit www.soletreadmills.com to register online.
ver. B
E35 / E75 / E95 Elliptical
2
Important Safety Instructions
WARNING - Read all instructions before using this appliance.
■ Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both
carpet and elliptical may result.
■ Keep children away from the elliptical. There are obvious pinch points and other
caution areas that can cause harm.
■ Keep hands away from all moving parts.
■ Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not
working properly, call your dealer.
■ Keep the cord away from heated surfaces.
■ Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous
environment.
■ Never drop or insert any object into any openings.
■ Do not use outdoors.
■ To disconnect, turn all controls to the off position, then remove the plug from the
outlet.
■ Do not attempt to use your
intended.
■ The hand pulse sensors are not medical devices. Various factors, including the
user’s movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
■ Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your elliptical. Quality athletic shoes are recommended to avoid leg
fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
elliptical for any purpose other than for the purpose it is
E35 / E75 / E95 Elliptical
3
Important Electrical Information
WARNING!
● NEVER remove any cover without first disconnecting AC power supply.
● If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical
may be affected. Such conditions are not covered under your warranty. If you
suspect the voltage is low, contact your local power company or a licensed electrician
for proper testing.
● NEVER expose this elliptical to rain or moisture. This product is NOT designed for
Use outdoors, near a pool or spa, or in any other high humidity environment.
Important Operation Instructions
NEVER operate this elliptical without reading and completely understanding the
●
results of any operational change you request from the computer.
● Understand that changes in resistance do not occur immediately. Set your desired
level on the computer console and release the adjustment key. The computer will
obey the command gradually.
● NEVER use your elliptical during an electrical storm. Surges may occur in your
household power supply that could damage elliptical components.
● Use caution while participating in other activities while using your elliptical such as
watching television, reading, etc. These distractions may cause you to lose balance
which may result in serious injury.
● Always hold on to a handrail or hand bar while making control changes.
Do not use excessive pressure on console control keys. They are precision set to
properly function with little finger pressure. Pushing harder is not going to make the unit
go faster or slower. If you feel the buttons are not functioning properly with normal
pressure, contact your Sole dealer.
E35 / E75 / E95 Elliptical
4
A
ssembly Instructions (E35.E75.E95)
■ UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted
Line. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If
damaged parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools
first. Remove the hardware for each step as needed to avoid confusion.
STEP 1: REAR RAIL ASSEMBLY
1. Remove the hardware from the hardware pack for step 1. You should have four
3-3/4” X 3/8” bolts, four curved washers, two 1/4” X 3/8” bolts, two flat washers
and six 3/4” X 1/8” Phillips head screws.
2. Put the two flat washers on the 2-1/4” bolts and hand-tighten them, through the
top of the middle stabilizer tube, into the rear rail assembly.
3. Put the four curved washers on the 3-3/4” bolts and hand-tighten them through
the front of the middle stabilizer tube, into the rear rail assembly.
4. Using the wrench provided tighten all six bolts securely.
5. Locate the four plastic covers (E35, E75 only) for the rear rail assembly and
the one cover for the front stabilizer and install them using the six 3/4” X
1/4“ screws and the Phillips head screw driver provided.
STEP 2: CONSOLE MAST ASSEMBLY
1. Remove the hardware from the hardware pack for step 2. You should have one
2-3/4” X 3/8” bolt, one lock washer, two 1” X 3/8” bolts, two curved washers and
four 1/2” X 1/4” Phillips head screws.
2. Locate the console mast and console mast cover and slide the cover onto the
mast as far as it will go. Make sure the cover is facing the correct way.
3. At the top opening of the main body of the elliptical is a wire harness. Unravel
and straighten out the wire harness and feed it into the bottom of the console
mast tube and out of the top opening.
4. Install the console mast into the receiving bracket in the top of the main body.
NOTE: there is one bolt already installed in the receiving bracket that will engage
with the slot at the bottom of the console mast. This needs to be tightened at the
end along with the three other console mast bolts.
5. Put the flat washer onto the 2 3/4” bolt and the two curved washers onto the two
E35 / E75 / E95 Elliptical
5
1” bolts. Install, and hand tighten, the 2 3/4” bolt through the left side of the
receiving tube into the console mast. NOTE: There is a wire running through the
tube. Be careful not to damage or pinch this wire during this procedure. Damage
to the electronic console could result. Install, and hand tighten, the two 1” bolts
through the front of the receiving tube into the console mast.
6. Using the two sided wrench tighten the three bolts, and the fourth bolt which is
pre-installed, firmly. These bolts should be tightened as much as you possibly
can.
7. Locate the electronic console and the four 1/2” X 1/4” Phillips head screws.
8. There will be two electrical wire connectors at the top opening of the console
mast, one 4 pin (hand pulse sensors), one 10 pin (main wire harness). Connect
these to the mating connectors on the back of the console. The connectors are
keyed so you cannot plug them in the wrong way so do not force them.
9. Storing the excess wire back into the console mast, carefully install the console
onto the mounting plate and secure using the four Phillips head screws.
10.Install the Bottle Holder onto console mast with two M5x12mm Phillips head
screws then place the Bottle in the Bottle Holder.
STEP 3: HANDLE BAR ASSEMBLY
1. Remove the hardware from the hardware pack for step 3. You should have two
5/8” X 3/8” bolts, two large flat washers, two large wave washers and four self
tapping Phillips head screws.
2. Locate and install the 2 large wave washers onto the handle bar axle, one on
each side.
3. Slide the left and right handle bars onto the appropriate side of the axle. There is
a sticker on each handle bar indicating L for left and R for right.
4. Put the large flat washers onto the two 5/8” X 3/8” bolts and install, and tighten,
in the threaded holes in the ends of the axle.
5. Install the plastic covers over the handle bar/axle connections with the six self
tapping Phillips head screws.
STEP 4: FOOT PAD/CONNECTING ARM ASSEMBLY
1. Remove the hardware from the hardware pack for step 4. You should have two
1-1/4” X 3/8” bolts, two flat washers, two Nylon nuts, four 5/8” machine screws
(long), four 3/8” machine screws (short) and two self tapping Phillips head
screws.
2. On the pedal arms, in the middle on top, there are two axles already installed in
E35 / E75 / E95 Elliptical
6
the bushing housings. Remove, from one side of each axle, the bolt (one should
be loose) and washer. Remove the axle and set aside for the next step.
3. Locate the left foot pad/connecting arm. Holding the rear of the foot pad with
your right hand and the connecting arm, just in front of the foot pad, with your left
hand, place the foot pad over the bushing housing.
4. Holding the axle (removed in step 2) in one hand, and the foot pad in the other,
line up the large hole in the side of the bracket (under the foot pad) with the hole
in the bushing housing and insert the axle all the way until the washer is flush
against the bracket. You may have to wiggle the axle while moving the foot pad
slightly to get the axle to go in.
5. Take the bolt that you removed from the axle in step 2 AND INSTALL THE NEW
ANTI-ROTATION BRACKET, then thread it into the hole in the axle. Tighten the
bolt using two wrenches provided. You have to put a wrench on both axle bolts to
tighten firmly.
6. Align the hole in the end of the connecting arm (pivoting rod end) with the hole in
the bracket of the handle bar. The rod end should be on the inside of the handle
bar bracket. Take one of the 1-1/4” X 3/8” bolts and install it through the handle
bar bracket and the rod end. Install a flat washer and Nylon nut on the bolt and
tighten firmly using a wrench on the nut and one on the bolt.
7. Repeat for the right side foot pad/connecting arm.
8. Install the plastic covers over the connection of the rod end and handle bar. The
front inside hole in the plastic uses a self tapping screw and the two rear holes
use the 3/8” machine screws (short). There is a short Phillips screw driver
provided for installing the inside screws.
9. Install the two wheel covers using the four 5/8” machine screws (long).
10. Install the locking pins for the adjust able foot pads into the desired holes (E75,
E95 only). *See Foot pad angle adjustment section for details of this feature.
11. This step is for the E95 only. Install the two plastic parts that make up the rear
shroud using the seven Phillips head screws.
E35 / E75 / E95 Elliptical
7
A
ssembly drawing (E35.E75.E95)
E35
Step1/ 2
E35 / E75 / E95 Elliptical
8
E35
Step3/4
E35 / E75 / E95 Elliptical
9
Loading...