Sole Fitness E55 Owner's Manual
1
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING
YOUR NEW ELLIPTICAL!
2
TABLE OF
CONTENTS
Important Safety Instructions 3
Important Electrical Information 4
Important Operation Instructions 5
Transport Instructions 5
Assembly Instructions 6
Elliptical Features 13
Operation of Your New Elliptical 14
Programmable Features 16
Using Heart Rate Monitor 22
General Maintenance 24
Exploded View Diagram 25
Parts List 26
ATTENTION
THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR
THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
SE579SB-SE006_1404(SL)A
3
IMPORTANT
SAFETY
INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your SOLE elliptical from the
electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the elliptical on a flat level surface with access to a 220-volt, 15-amp grounded outlet with
only the elliptical plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH
ONLY ONE OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE
GROUNDED PLUG BY USING IMPROPER ADAPTERS, OR IN ANY WAY MODIFY
THE CORD SET.
A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions,
page 4.
Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both
carpet and elliptical may result.
Keep children away from the elliptical. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not
working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position and then remove the plug from the
outlet.
Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
4
IMPORTANT
ELECTRICAL
INSTRUCTIONS
WARNING!
NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your elliptical may be
affected. Such conditions are not covered under your warranty. If you suspect the
voltage is low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operating
temperature specification is 40 to 120 degrees Fahrenheit, and humidity is 95%
non-condensing (no water drops forming on surfaces).
GROUNDING INSTRUCTIONS
This product must be grounded. If the elliptical should malfunction or breakdown,
ground
ing provides a path of least resistance for electric current, reducing the risk of electric
shock. This product is equipped with a cord having an equipment-grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in
doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product if it will not fit the outlet; have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 220-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly
grounded outlet is not available. The temporary adapter should be used only until a properly
grounded outlet, (shown below) can be installed by a qualified electrician. The green colored
rigid ear-lug, or the like, extending from the adapter, must be connected to a permanent
ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must
be held in place by a metal screw.
5
IMPORTANT
OPERATION
INSTRUCTIONS
NEVER operate this elliptical without reading and completely understanding the results
of
any operational change you request from the computer.
Understand that changes in resistance and incline do not occur immediately. Set your
desired resistance level on the computer console and release the adjustment key.
The computer will obey the command gradually.
NEVER use your elliptical during an electrical storm. Surges may occur in your
household power supply that could damage elliptical components. Unplug the elliptical
during an electrical storm as a precaution.
Use caution while participating in other activities while using your elliptical; such as
watching television, reading, etc. These distractions may cause you to lose balance;
which may result in serious injury.
Always hold on to a handle bar while making control changes (incline, level, etc.).
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure. If you feel the buttons are not functioning
properly with normal pressure contact your SOLE dealer.
POWER CONNECTOR - FRONT, LEFT SIDE OF UNIT
TRANSPORT
INSTRUCTIONS
The elliptical is equippped with two transport wheels which are engaged when the rear of the
elliptical is lifted.
6
ASSEMBLY PACK CHECKLIST
1
HARDWARE
STEP 1
#142
. Ø10 × Ø19 × 1.5T_
Flat Washer Flat Washer
(2 pcs)
#157
. Ø8 × 20 × 1.5T_
Flat Washer Flat W
asher
(4 pcs)
#156. Ø10 × Ø23 × 2T_
Curved Washer (2 pcs)
#155
. Ø10 × 2T_
Spring Washer (1 pc)
#117.
M5 × P0.8 ×
10L_ Phillips Head
Screw
(4 pcs)
#134
. 3/8" × UNC16 ×
7T_Nyloc Nut (2 pcs)
#158
. Ø8 ×
1.5T_Spring Washer
(4 pcs)
#151
. Ø8 × 0.8T_Star
Washer (4 pcs)
#106
. 3/8" × UNC16 ×
3/4"_Hex Head Bolt
(2 pcs)
#108
. 5/16" × UNC18 × 2-1/4"_
Hex Head Bolt (4 pcs)
#107. 3/8" × UNC16 × 1-1/2"_
Hex Head Bolt (2 pcs)
#101
. 3/8" × UNC16 ×
2-1/4"_Hex Head Bolt (1 pc)
7
2
HARDWARE
STEP 2
3
HARDWARE
STEP 3
4
HARDWARE
STEP 4
#100
. 5/16" × UNC18 × 15L_
Hex Head Bolt
(2 pcs)
#126
. Ø3.5 × 12L_
Sheet Metal Screw
(6 pcs)
#145
. Ø8 × Ø23 × 1.5T_
Flat Washer (2 pcs)
#153
. Ø17 × 0.3T_
Wave Washer (4 pcs)
Switch Wire Cap
(2 pcs)
#109
. 5/16" × UNC18 ×
1-1/4"_Hex Head Bolt (2
pcs)
#137. 5/16" × UNC18 ×
7T_Nyloc Nut (2 pcs)
#157
. Ø8 × 20 × 1.5T_
Flat Washer (2 pcs)
#115. M5 × P0.8 × 15L_
Phillips Head Screw
(23 pcs)
#125
. M6 × P1.0 × 10L_
Phillips Head Screw
(4 pcs)
#126
. Ø3.5 × 12L_Sheet
Metal Screw (4 pcs)
8
ASSEMBLY
TOOLS
#159. 13/14mm Wrench
(160mm)
#161. Phillips Head Screwdriver
#160. Short Phillips Head Screwdriver
#162. 12/14mm Wrench (160mm
ASSEMB
L
Y
INSTRU
C
TIONS
PRE
-ASSEMBLY
1.
Using a razor knife (Box Cutter) cut the outside, bottom, edge of
box along the dotted Line. Lift Box over the unit and unpack.
2.
Carefully remove all parts from carton and inspect for any
damage or missing parts. If damaged parts are found, or parts
are missing, contact your dealer immediately.
3.
for each step as needed to avoid confusion. The numbers in the
instructions that are in parenthesis (#) are the item number from
the assembly drawing for reference.
9
1
2
INCLINE
BASE & MAST
ASSEMBLY
See Page 9 for Illustration
1. Connect the Rail Base Assembly (2) with the Rear Stabilizer of the
Main Frame (1) using two Hex Head Bolts (107), two Flat Washers
(142), two Nyloc Nuts (134) and four Hex Head Bolts (108) with
four Flat Washers (157), four Spring Washers (158) and four Star
Washer (151). Tighten with the wrenches pro- vided (159 & 162).
2. Connect the connecting wires for the incline motor (48 & 49), by
matching the color codes of red, white and black.
3. Guide the Computer Cable (50) through the Console Mast Cover
(72) and Console Mast (12), which also goes through Console
Mast Cover (72). Pull the connector out of Console Mast (12) and
insert into the U-Base on the main- frame and secure with the Hex
Head Bolt (101) and Split Washer (155)that
are on the U-Base and two Hex Head Bolts (106) and two
Curved Washers (156). Use the Wrench (159) to secure the
Console Mast (12) to the U-Base. Then slide the Console Mast
Cover (72) down.
4. Plug in the Computer Cable (50), two Handpulse Cables (34 & 35),
Upper Resistance Handle Cable (39), and Upper Incline Handle
Cable (40) on the bottom of Console Assembly (45) and secure
the Console Assembly (45) on the console holding plate with four
Phillips Head Screws (117) by tightening them with Phillips Head
Screw Driver (161).
HANDLE BAR
ASSEMBLY
See Page10 for Illustration
1. Slide on two Wave Washers (153) and the corresponding Swing
Arm (10-L) and (11-R) to each side of Console Mast shaft and
secure with two Hex Head Bolts (100) and two Flat Washers (145)
using the Wrench (162).
2. Connect the Upper Handle Resistance Cable (39) and Upper
Handle Incline Cable (40) with the Lower Resistance/Incline
Cables (198). Push the excessive wire into the Console Mast (12)
and plug the Switch Wire Cap (185) into each side of the Console
Mast (12).
3. Match the Front Handle Bar Cover (83-L) with Rear Handle Bar
Cover (84-L) on the left Swing Arm (10) and secure with three
Sheet Metal Screws (126) using the Phillips Head Screw Driver
(161). Repeat on the Right Swing Arm (11) with the Front Handle
Bar Cover (86-L), Rear Handle Bar Cover (85-R) and three Sheet
Metal Screws (126).
HARDWARE STEP 1
#101. 3/8" × UNC16
× 2-1/4"_Hex Head
Bolt (1 pcs)
#106. 3/8" × UNC16 ×
3/4"_Hex Head Bolt (2
pcs)
#107. 3/8" × UNC16
× 1-1/2"_Hex Head
Bolt (2 pcs)
#108. 5/16" × UNC18 ×
2-1/4"_Hex Head Bolt (4
pcs)
#117 M5 × P0.8 ×
10L_Phillips Head Screw
(4 pcs)
#134. 3/8" × UNC16 ×
7T_Nyloc Nut (2 pcs)
#142. Ø10 × Ø19 ×
1.5T_Flat Washer (2 pcs)
#151. Ø8 × 0.8T_Star
Washer (4 pcs)
#155. Ø10 × 2T_Spring
Washer (1 pc)
#156. Ø10 × Ø23 ×
2T_Curved Washer (2
pcs)
#157. Ø8 × Ø20 ×
1.5T_Flat Washer (4 pcs)
#158. Ø8 × 1.5T_Spring
Washer (4 pcs)
HARDWARE STEP 2
#100. 5/16" × UNC18 ×
15L_Hex Head Bolt
(2 pcs)
#126. Ø3.5 × 12L_Sheet
Metal Screw (6 pcs)
#145. Ø8 × Ø23 ×
1.5T_Flat Washer (2 pcs)
#153. Ø17 × 0.3T_Wave
Washer (4 pcs)
#185. Switch Wire Cap
(2 pcs)
Loading...