Sole Fitness E20 elliptiacl Owner's Manual

OWNER’S MANUAL

PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING
YOUR NEW ELLIPTICAL!

-SOL0017-

2

TABLE OF CONTENTS

Important Safety Instructions 3

Important Electrical Information 4

Important Operation Instructions 5

Transport Instructions 5

Assembly Instructions 7

Elliptical Features 11

Operation of Your New Elliptical 12

Programmable Features 15

Using Heart Rate Monitor 20

General Maintenance 22

Exploded View Diagram 23

Parts List 24

Manufacturer’s Limited Warranty 28

ATTENTION

THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED
FOR THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS
ENTIRETY.

SOL0017 / E20_ver.A

3

IMPORTANT SAFETY INSTRUCTIONS

WARNING - Read all instructions before using this appliance.

DANGER - To reduce the risk of electric shock disconnect your elliptical from the

electrical outlet prior to cleaning and/or service work.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install

the elliptical on a flat level surface with access to a 230-volt, 15-amp grounded outlet
with only the elliptical plugged into the circuit.

DO NOT USE AN EXTENSION CORD UNLESS IT IS A 18AWG OR BETTER,
WITH ONLY ONE OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE
GROUNDED PLUG BY USING IMPROPER ADAPTERS, OR IN ANY WAY
MODIFY THE CORD SET.

A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions.

 Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both

carpet and elliptical may result.

 Keep children away from the elliptical. There are obvious pinch points and other

caution areas that can cause harm.

 Keep hands away from all moving parts.
 Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not

working properly, call your dealer.

 Keep the cord away from heated surfaces.
 Do not operate where aerosol spray products are being used or where oxygen is

being administered. Sparks from the motor may ignite a highly gaseous
environment.

 Never drop or insert any object into any openings.
 Do not use outdoors.
 To disconnect, turn all controls to the off position and then remove the plug from

the outlet.

 Do not attempt to use your elliptical for any purpose other than for the purpose it is

intended.

 The hand pulse sensors are not medical devices. Various factors, including the

user’s movement, may affect the accuracy of heart rate readings. The pulse
sensors are intended only as exercise aids in determining heart rate trends in
general.

 Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable

for use on your elliptical. Quality athletic shoes are recommended to avoid leg
fatigue.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

4

IMPORTANT ELECTRICAL INSTRUCTIONS

WARNING!

NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your elliptical may
be affected. Such conditions are not covered under your warranty. If you suspect
the voltage is low, contact your local power company or a licensed electrician for
proper testing.
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operating
temperature specification is 40 to 120 degrees Fahrenheit, and humidity is 95%
non-condensing(no water drops forming on surfaces).

GROUNDING INSTRUCTIONS

This product must be grounded. If the elliptical should malfunction or breakdown,
ground- ing provides a path of least resistance for electric current, reducing the risk of
electric shock. This product is equipped with a cord having an equipment-grounding
plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.

DANGER - Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or serviceman if you are
in doubt as to whether the product is properly grounded. Do not modify the plug
provided with the product if it will not fit the outlet; have a proper outlet installed by a
qualified electrician. This product is for use on a nominal 230-volt circuit, and has a

grounding plug.

5

IMPORTANT OPERATION INSTRUCTIONS

 NEVER operate this elliptical without reading and completely understanding the

results of any operational change you request from the computer.

 Understand that changes in resistance and incline do not occur immediately. Set

your desired resistance level on the computer console and release the adjustment
key. The computer will obey the command gradually.

 NEVER use your elliptical during an electrical storm. Surges may occur in your

household power supply that could damage elliptical components. Unplug the
elliptical during an electrical storm as a precaution.

 Use caution while participating in other activities while using your elliptical; such as

watching television, reading, etc. These distractions may cause you to lose balance;
which may result in serious injury.

 Always hold on to a handle bar while making control changes (incline, level, etc.).
 Do not use excessive pressure on console control keys. They are precision set to

function properly with little finger pressure. If you feel the buttons are not
functioning properly with normal pressure contact your dealer.

POWER CONNECTOR - FRONT, LEFT SIDE OF UNIT

TRANSPORT INSTRUCTIONS

The elliptical is equippped with two transport wheels which are engaged when the rear of the
elliptical is lifted.

6

ASSEMBLY PACK CHECKLIST

1

HARDWARE STEP 1

2

HARDWARE STEP 2

3

HARDWARE STEP 3

#112

. 3/8” x 3-3/4”

Hex Head Bolt (4 pcs)

#113

. 3/8” x 3/4”

Socket Head Cap Bolt (4 pcs)

#119.

M5 x 10mm

Phillips Head Screw (4 pcs)

#139

. 3/8” x 19mm x 1.5T

Flat Washer (4 pcs)

#142. 3/8” x 2T
Split Washer (8 pcs)

#144

. 3/8” x 23 x 2T

Curved Washer (4 pcs)

#104

. 5/16” x 15mm

Hex Head Bolt (2 pcs)

#115

. 5/16” x 15mm Button

Head Socket Bolt (2 pcs)

#138

. Ø8.5 × 26mm × 2T

Flat Washer (4 pcs)

#106

. 5/16” x 1-3/4”

Hex Head Bolt (6 pcs)

#129

. 5/16” x 7T

Nyloc Nut (6 pcs)

#143

. 5/16” x 23mm x 1.5T

Curved Washer (4 pcs)

7

4

HARDWARE STEP 4

ASSEMBLY TOOLS

ASSEMBLY INSTRUCTIONS

PRE-ASSEMBLY

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing parts. If
damaged parts are found, or parts are missing, contact your dealer immediately.

3. Locate the hardware package. Remove the tools first. Remove the hardware for each step as
needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the
item number from the assembly drawing for reference.

#120

. M5 x 15mm

Phillips Head Screw (4 pcs)

#122

. Ø3.5 x 12mm

Sheet Metal Screw (6 pcs)

#149. M5 L Allen Wrench #150. Phillips Head Screwdriver

#152. 12/14mm

Wrench (160mm)

#153. M8 L Allen Wrench

#151

. 13/14mm

Wrench (160mm)

8

#112. 3/8” x 3-3/4” Hex
Head Bolt (4 pcs)
#113. 3/8” x 3/4”

Socket

Head Cap Bolt

(4 pcs)

#119. M5 x 10mm Phillips
Head Screw

(4 pcs)

#139. 3/8” x 19mm x

1.5T
Flat Washer (4 pcs)
#142. 3/8” x2T Spli

t
Washer (8 pcs)
#144. 3/8” x 23 x 2T
Curved Washer (4 pcs)

ASSEMBLY INSTRUCTIONS

1

STABILIZERS & CONSOLE MAST

HARDWARE STEP 1

1. Connect the Front Stabilizer Bar (2) with the Main Frame at the front joining
plate by using the Wrench (151) to tighten two Hex Head Bolts (112) , two Split
Washers (142) and two Curved Washers (144).

2. Connect the Rear Stabilizer (3) with the Main Frame at the rear joining plate by
using the Wrench (151) to tighten two Hex Head Bolts (112) , two Split Washers
(142) and two Curved Washers (144).

3. Pull the wire, which is attached to the Computer Cable (38), out of Console Mast
(15) and secure the mast on the Main Frame by using the M8 L Allen Wrench
(153) to tighten four Socket Head Cap Bolts (113) together with four Split
Washers (142) and four Flat Washers (139).

4. Plug in the connectors of the Computer Cable (38) and two Handpulse with
Cable Assemblies (White & Red) (44, 45) on the back of the Console Assembly
(35) and secure the Console Assembly (35) on the console holding plate with
four Phillips Head Screws (119) by tightening them with Phillips Head Screw
Driver (150).

ASSEMBLY STEP 1

9

#104. 5/16” x 15mm
Hex Head Bolt (2 pcs)

#115. 5/16” x 15mm
Button Head Socket Bolt
(2 pcs)
#138. Ø8.5 × 26mm× 2T
Flat Washer (4 pcs)

2

LOWER SWING ARMS

HARDWARE STEP 2

1.

Attach the Lower Swing Arms (L) and (R), (12) and (13), on each side of
Console Mast shaft and secure with two Hex Head Bolts (104) and two Flat
Washers (138) by using the Wrench (152).

2.

Insert the shaft of the left Connecting Arm (10) through the bushing on left
Pedal Arm (7) and secure with a Button Head Socket Bolt (115) together with a
Flat Washer (138) by using M5 L Allen Wrench (149). Do it the same way for
right Connecting Arm (11) and right Pedal Arm (8).

3.

Remove the Rod End Shafts (20) which are pre-assembled on the left and right
Connecting Arms. Assemble the Connecting Arm with the Lower Swing Arm
and secure with Rod End Shafts (20)

and

the screw by using

12/14m/m_Wrench (160m/m)(152).

ASSEMBLY STEP 2