Sole Fitness F63, F65, 16810365 Owner's Manual
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW TREADMILL
-SOL0013/SOL0014-
1
TABLE OF CONTENTS
Important Safety Instructions 3
Important Electrical Information 4
Important Operation Instructions 5
Important Safety Instructions 6
F63/F65 Assembly Pack Checklist 7
F63/F65 Assembly instructions 9
Folding Instructions 13
Operation of Your Treadmill 14
Programmable Features 19
General Maintenance 26
Service Checklist - Diagnosis Guide 29
F63 Exploded View Diagram
31
F63 Parts List
32
F65 Exploded View Diagram
38
F65 Parts List
39
Manufacturer’s Limite Warranty
45
F63/SOL0013&F65/SOL0014_ver.A(2013)
2
Congratulations on your new treadmill and welcome to the Spirit family!
Thank you for your purchase of this quality treadmill from Spirit Manufacturing, Inc. Your new treadmill
was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the
most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your
ownership experience as pleasant as possible for many years to come. If not purchased direct from
Spirit, the local dealership where you purchased this treadmill is your administrator for all Spirit
warranty and service needs. Their responsibility is to provide you with the technical knowledge and
service personnel to make your experience more informed and any difficulties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number, and the
date of purchase below to make any future, needed contact easy. We appreciate your support and we
will always remember that you are the reason that we are in business.
Please complete and mail your registration card today and enjoy your new treadmill.
Yours in Health,
BOYLES FITNESS Equipment Pty Ltd.
Name of Dealer______________________________________
Purchase Date_______________________________________
3
IMPORTANTSAFETYINSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your treadmill from the
electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the treadmill on a flat level surface with access to a 230-volt, 10-amp grounded outlet with only
the treadmill plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY
ONE OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY
USING IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET.
A serious shock or fire hazard may result along with computer malfunctions. See Grounding
Instructions, page 4.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and
treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance between the
rear of the treadmill and any fixed object.
Keep children away from the treadmill. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working
properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you with an
approximate measurement in relation to your target heart rate. Use of a chest transmitter
strap is a much more accurate method of heart rate analysis. Various factors, including the
user’s movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
4
IMPORTANTELECTRICALINFORMATION
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any
appliance with a large motor, the GFCI will trip often. Route the power cord away from any
moving part of the treadmill including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent
(10%) or more, the performance of your treadmill may be affected. Such conditions are not
covered under your warranty. If you suspect the voltage is low, contact your local power company
or a licensed electrician for proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The maximum
operating temperature specification is 40 degrees c, and humidity is 95% non-condensing (no
water drops forming on surfaces).
Circuit Breakers: Some circuit breakers used in homes are not rated for high inrush currents
that can occur when a treadmill is first turned on or even during use. If your treadmill is
tripping the house circuit breaker (even though it is the proper current rating) but the circuit
breaker on the treadmill itself does not trip, you will need to replace the home breaker with a
high inrush type. This is not a warranty defect.This is a condition we as a manufacture have
no ability to control. This part is available through most electrical supply stores. Examples:
Grainger part # 1D237, or available online at www.squared.com part # QO120HM.
GROUNDINGINSTRUCTIONS
This product must be grounded. If the treadmill should malfunction or breakdown, grounding
provides a path of least resistance for electric current, reducing the risk of electric shock. This
product is equipped with a cord having an equipment-grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or serviceman if you are in
doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product if it w ill not fit the outlet; have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 230-volt circuit, and has a grounding plug that looks like the plug
illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to
connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available.
The temporary adapter should be used
only until a properly grounded outlet,
(shown below) can be installed by a
qualified electrician. The green colored
rigid ear-lug, or the like, extending from
the adapter, must be connected to a
permanent ground such as a properly
grounded outlet box cover. Whenever
the adapter is used, it must be held in place by a metal screw.
5
IMPORTANTOPERATIONINSTRUCTIONS
NEVER operate this treadmill without reading and completely understanding the results
of any operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your desired
work level on the computer console and release the adjustment key. The computer will obey
the command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your household
power supply that could damage treadmill components. Unplug the treadmill during an
electrical storm as a precaution.
Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance which
may result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure.
SAFETYTETHERCORD
A safety tether cord is provided with this unit. It is a simple magnetic design that should be
used at all times. It is for your safety should you fall or move too far back on the tread-belt.
Pulling this safety tether cord will stop tread-belt movement. To Use:
1. Place the magnet into position on the round metal portion of the console control head.
Your treadmill will not start and operate without this. Removing the magnet also secures the
treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The
magnet has strong enough power to minimize accidental, unexpected stopping. The clip
should be attached securely to make certain it does not come off. Be familiar with its
function and limitations. The treadmill will stop, depending on speed, with a one to two step
coast anytime the magnet is pulled off the console. Use the Stop / Pause switch in normal
operation.
6
IMPORTANTSAFETYINSTRUCTIONS
READ BEFORE UNPACKING YOUR FOLDING TREADMILL
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill from
unfolding accidentally during shipping. If this strap is not removed properly the treadmill could
spring open unexpectedly and cause injury if someone is standing near the treadmill when the
strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure the
treadmill is positioned flat on the ground, in the orientation it would be in if you were using the
treadmill. Do not turn the treadmill up on its side while removing the shipping strap. This could
cause the treadmill’s folding mechanism to spring open. If the end of the Velcro strap (that you
need to grab to remove it) happens to be under the treadmill deck, reach under the deck to grab it,
but do not tilt the treadmill up to gain access to the strap end.
PREVENTATIVEMAINTENANCECHART
Vacuum Under
Motor
Cover&Check
Wiring(Every
Other Month)
Clean&Inspect
Deck for
Lubrication(Every
Other Month)
Lubricate
Deck(Every 90
hours or sooner if
dry)
Inspect Belt
Tracking(Monthly)Adjust
if necessary
Date
7
F63/F65ASSEMBLYPACKCHECKLIST
HARDWARESTEP2
HARDWARESTEP3
HARDWARESTEP5
HARDWARESTEP6
2
#128.M5
Speed Nuts Clip (6 pcs)
3
#130. 5/16" × 1/2"
Button Head Socket Bolt (8 pcs)
5
#113. Ø10 × 2T
Split Washer (4 pcs)
6
#175. 3.5 × 16mm
Sheet Metal Screws (6 pcs)
#139. 3/8" × 1-3/4"
Button Head Socket Bolt (4 pcs)
8
HARDWARESTEP7
HARDWARESTEP8
ASSEMBLYTOOLS
8
#120. 5 × 16mm
Tapping Screw (6 pcs)
7
#159. 5/16" × 3/4"
Button Head Socket Bolt (4 pcs)
#75. Safety Key
#131. Combination M5 Allen Wrench
& Phillips Head Screw Driver
#132. M6 Allen Wrench
9
F63/F65ASSEMBLYINSTRUCTIONS
ASSEMBLYSTEP1
1. Remove the treadmill from the carton and position it aside on a smooth, level
floor.The rear should be at least 3’from any wall.Do not remove the Velcro
belt until you have rmoved the plastic wrap and styrofoam from beneath
the unit. Turning the unit on its side after removing the belt may cause
the unit fold up and cause serious injury!
ASSEMBLYSTEP2
1. Install the six Speed Nut Clips(128)on the Frame Base left and right side.
2. Slide the lower handlebar covers(142L&144R)onto the console masts
(notice orientation).
3. Slide the Frame Base Caps(62L&63R)over the Upright tubes(4&5).
Connect the Lower Computer Cable(49)to the Middle Comput Cable(50)
On the right side of the unit.
Before attaching the hardware to Step 3, make sure the cables you just connected don’t
get pinched in between the steel tubing. If they do, this may cause issues that prevent
the treadmill from operating properly.
1
2
128
128
128
128
128
128
62
63
4
5
49
50
144
142
#128.M5 Speed Nuts
Clips (6 pcs)
HARDWARESTEP2
10
ASSEMBLYSTEP3
1. Attach the upright Tubes(4&5)onto the Frame Base(2)with eight Button
Head Socket Bolts(130)by using the Combination M5 Allen Wrench&
Phillips Head Screw Driver(131).Do not tighten the bolts completely
Until Step 7 is finished.
ASSEMBLYSTEP4
To complete this step, it is recommended that you find something to rest the
Console on at the appropriate height or have someone hold the console while
You connect the cables.
1. Connect the Speed Adjustment Switch Cable(54)to the Speed Cable,Upper
(37)Connect the Incline Adjustment Switch Cable(55)to the Incline Cable,
Upper(38). Connect the Computer Cable, Middle(50) and Computer Cable,
Upper(48), TucK the excess cable into the hand rail tubing to prevent it from
Getting pinched.
Before attacheing the hardware to Step 5, make sure the cables you just connected don’t
get pinched in between the steel tubing. If they do, this may cause issues that prevent
the treadmill from operating properly.
3
131
130
130
2
130
130
5
4
#130. 5/16" × 1/2" Button
Head Socket Bolts (8 pcs)
HARDWARESTEP3
4
38
55
48
50
37
54
11
ASSEMBLYSTEP5
ASSEMBLYSTEP1
1. Insert the Console Assembly (52) into the Upright Tubes (4&5)and attach
with four Button Head Socket Bolts (139)and four Split Washers (113).
Tighten using the M6 L Allen Wrench (132).
ASSEMBLYSTEP6
1. Attach the Left(141&142) and Right (143&144)Upper and lower
Handlebar Covers to the top of the Upright Tubes (4&5) with six Sheet
Metal Screws(175). Tighten with the Combination M5 Allen Wrench &
Phillips Head Screw Driver (131).
5
4
5
#139. 3/8" × 1-3/4" Button
Head Socket Bolts(4 pcs)
#113. Ø10 × 2T
Split Washers (4 pcs)
HARDWARESTEP5
6
144
142
143
141
4
5
31
175
175
175
175
5
4
#175. 3.5 × 16mm
Sheet Metal
Screws (6 pcs)
HARDWARESTEP6
12
ASSEMBLYSTEP7
1. Attach the Support tube (26) between the upright tubes (4&5) with four
Button Head Socket Bolts (159).Tighten bolts firmly.
2. Place the Beverage Holder (158) on top of the Support tube (26) as shown
In the illustration.
3. Place the magnet of the safety key (75) in between the Start and Stop
buttons (if it isn’t already attached).The treadmill will not function without this
In place.
4. Check to make sure all bolts and screws are completely tightened.
ASSEMBLYSTEP8
1. Finish tightening the button head bolts (from Step 2 above) that secure the
Console matsts to the frame.
2. Attach the console mast covers (62&63) to the Frame Base (2) with six
Tapping Screws (120). Tighten screws using the Combination M5 Allen
Wrench & Phillips Head Screw Driver (131).
7
131
159
159
159
159
5
26
4
158
#159. 5/16" × 3/4" Button
Head Socket Bolts (4 pcs)
#75. Safety Key
HARDWARESTEP7
8
62
120
120
120
120
120
63
131
120
#120. 5 × 16mm
Tapping Screws (6 pcs)
HARDWARESTEP8
75
13
FOLDINGINSTRUCTIONS
Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power
cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired
position.
TO FOLD THE TREADMILL
Make certain the treadmill is at minimum incline. Lift the
treadmill running deck until it is secured by the locking
telescoping tube assembly in center back of base.
TO UNFOLD THE TREADMILL
Apply slight forward pressure* on the treadmill running deck
with one hand. Pull down on the unlocking lever and slowly
lower the running deck to the floor. The deck will lower
unassisted when it reaches about waist high.
*At the rear roller area to relieve pressure on the
locking system.
TRANSPORTATIONINSTRUCTIONS
The treadmill is equipped with four transport wheels that are engaged when the treadmill is folded.
After folding simply roll the treadmill away.
14
OPERATIONOFYOURTREADMILL
GETTINGFAMILIARWITHTHECONTROLPANEL
INCLINEQUICKKEYS
SPEAKER
DISPLAYBUTTON
CONTROLKEYS
AUDIOINJACK
(MP3,CD,OR
SMARTPHONE)
SPEEDQUICKKEYS
SPEAKER
FANPOWERSWITCH
DOTMATRIXDISPLAY
HEADPHONEJACK
CONTACTHEART
RATESENSORS
COOLINGFANS
F63CONSOLE
INCLINEQUICKKEYS
SPEAKER
DISPLAYBUTTON
CONTROLKEYS
AUDIOINJACK
(MP3,CD,OR
SMARTPHONE)
COOLINGFANS
SPEEDQUICKKEYS
SPEAKER
FANPOWERSWITCH
DOTMATRIXDISPLAY
HEADPHONEJACK
CONTACTHEART
RATESENSORS
F65CONSOLE
Loading...