Sole S77 User Manual
OWNER’S MANUAL
S77 Trea d mill
Please carefully read this entire manual
before operating your new treadmill.
TABLE OF CONTENTS
Product Registration
Important Safety Instructions
Important Electrical Information
Important Operation Instructions
Assembly Instructions
Transport Instructions
Operation of Your New Treadmill
Programmable Features
General Maintenance
1
2
3
4
8
12
13
17
24
Service Checklist - Diagnosis Guide
Manufacturer’s Limited Warranty
27
29
CONGRATULATIONS ON YOUR NEW TREADMILL AND WELCOME TO THE SOLE FAMILY!
Thank you for your purchase of this quality treadmill from SOLE. Your new treadmill has been
manufactured by one of the leading tness manufacturers in the world and is backed by one of the most
comprehensive warranties available. SOLE will do all we can to make your ownership
experience as pleasant as possible for many years to come.
If you have any questions about your new product or questions about the warranty contact SOLE Fitness at
1-866-780-SOLE (7653). If you have a technical problem with your new treadmill contact SOLE technical
service at 866-MYSOLE1 (1-800-697-6531).
Please take a moment at this time to record below the name of the dealer, their telephone number, and the
date of purchase for easy contact in the future. We appreciate your condence in SOLE and we will always
remember that you are the reason that we are in business. Please complete and mail your registration card
today and enjoy your new treadmill.
Yours in Health,
SOLE Fitness
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT REGISTRATION
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this tness
product in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soletreadmills.com under the support tab to register online.
S77_20120725
1
S77 TREADMILL
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your SOLE treadmill from the electrical
outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons, install
the treadmill on a at level surface with access to a 110-volt, 15-amp grounded outlet with only
the treadmill plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING
IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET.
A serious shock or re hazard may result along with computer malfunctions. See Grounding Instructions, page 3.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet
and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance between
the rear of the treadmill and any xed object.
Keep children away from the treadmill. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working
properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the o position, remove tether cord, then remove the plug
from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The pulse sensors are not medical devices. Various factors, including the user’s movement,
may aect the accuracy of heart rate readings. The pulse sensors are intended only as
exercise aids in determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
2S77 TREADMILL
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any
appliance with a large motor, the GFCI will trip often. Route the power cord away from any
moving part of the treadmill including the elevation mechanism and transport wheels.
NEVER remove any cover without rst disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your treadmill may be
aected. Such conditions are not covered under your warranty. If you suspect the voltage is low,
contact your local power company or a licensed electrician for proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment. The maximum operating
temperature specication is 40 degrees c, and humidity is 95% non-condensing
(no water drops forming on surfaces).
Circuit Breakers: Some circuit breakers used in homes are not rated for high inrush currents
that can occur when a treadmill is rst turned on or even during use. If your treadmill is tripping
the house circuit breaker (even though it is the proper current rating) but the circuit breaker on
the treadmill itself does not trip, you will need to replace the home breaker with a high inrush
type. This is not a warranty defect. This is a condition we as a manufacture have no ability to
control. This part is available through most electrical supply stores. Examples:
Grainger part # 1D237, or available online at www.squared.com part # QO120HM.
GROUNDING INSTRUCTIONS
This product must be grounded. If the treadmill should malfunction or breakdown,
grounding provides a path of least resistance for electric current, reducing the risk of electric
shock. This product is equipped with a cord having an equipment-grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the
product if it will not t the outlet; have a proper outlet installed by a qualied electrician.
This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available. The temporary adapter should be used only until a properly grounded
outlet, (shown below) can be installed by a qualied electrician. The green colored rigid earlug, or the like, extending
from the adapter, must be
connected to a permanent
ground such as a properly
grounded outlet box cover.
Whenever the adapter is
used, it must be held in
place by a metal screw.
3
S77 TREADMILL
IMPORTANT OPERATION INSTRUCTIONS
NEVER operate this treadmill without reading and completely understanding the results of
any operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your desired
speed on the computer console and release the adjustment key. The computer will obey the
command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your household
power supply that could damage treadmill components. Unplug the treadmill during an
electrical storm as a precaution.
Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or stray
from walking in the center of the belt; which may result in serious injury.
NEVER mount or dismount the treadmill while the belt is moving. SOLE treadmills start at a
very low speed and it is unnecessary to straddle the belt during start up. Simply standing on
the belt during slow acceleration is proper after you have learned to operate the unit.
Always hold on to a handrail or hand bar while making control changes (incline, speed, etc.).
Do not use excessive pressure on console control keys. They are precision set to function
properly with little nger pressure. Pushing harder is not going to make the unit go faster
or slower. If you feel the buttons are not functioning properly with normal pressure contact
your SOLE dealer.
IMPORTANT SAFETY INSTRUCTIONS
A safety tether cord is provided with this unit and should be used at all times. It is for your safety
should you fall or move too far back on the tread-belt. Pulling this safety tether cord will stop
tread-belt movement.
To Use:
1. Place the safety key into position on the console control head. Your treadmill will not start
and operate without this. Removing the safety key also secures the treadmill from
unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power.
Note: The clip should be attached securely to make certain it does not come o. Be familiar
with its function and limitations. The treadmill will stop, depending on speed, with a one to
two step coast anytime the safety key is pulled o the console. Use the red Stop switch in
normal operation.
4S77 TREADMILL
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE UNPACKING YOUR FOLDING TREADMILL
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill from
unfolding accidentally during shipping. If this strap is not removed properly the treadmill could
spring open unexpectedly and cause injury if someone is standing near the treadmill when the
strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure the
treadmill is positioned at on the ground, in the orientation it would be in if you were using the
treadmill. Do not turn the treadmill up on its side while removing the shipping strap. This could
cause the treadmill’s folding mechanism to spring open. If the end of the Velcro strap (that you
need to grab to remove it) happens to be under the treadmill deck, reach under the deck to
grab it, but do not tilt the treadmill up to gain access to the strap end.
PREVENTATIVE MAINTENANCE CHART
Vacuum Under
Motor Cover &
Check Wiring
(Every Other
Month)
Clean & Inspect Deck
for Lubrication
(Every Other Month)
Lubricate Deck
(Every 90 hours
or sooner if dry)
Inspect Belt Tracking
(Monthly) Adjust if
necessary
Date
5
S77 TREADMILL
3
S77 ASSEMBLY PACK CHECKLIST
HARDWARE STEP 3
5
#79. Ø10mm × Ø19mm × 1.5T
Flat Washer (6 pcs)
#123. 3/8” x 2-1/2”
Button Head Socket Bolt (6 pcs)
HARDWARE STEP 5
#86. 3/8” x 2T
Split Washer (4 pcs)
#86. 3/8” x 2T
Split Washer (6 pcs)
#124. Ø8mm × Ø23mm × 1.5T
Curved Washer (4 pcs)
#91. 3/8” x 1-3/4”
Button Head Socket Bolt (4 pcs)
#100. 5/16” x 3/4”
Button Head Socket
Bolt (4 pcs)
6
HARDWARE STEP 6
#125. 3.5mm x 16mm
Sheet Metal Screw (6 pcs)
6S77 TREADMILL
7
8
HARDWARE STEP 7
#100. 5/16” x 3/4”
Button Head Socket Bolt (4 pcs)
HARDWARE STEP 8
#127. M5 x 10mm
Phillips Head Screw (4 pcs)
ASSEMBLY TOOLS
#103. Combination M5 Allen Wrench
& Phillips Head Screw Driver
#104. M6 L Allen Wrench
7
S77 TREADMILL
33
4
S77 ASSEMBLY INSTRUCTIONS
ASSEMBLY STEP 1
1
1. Remove the treadmill from the carton and position it aside on a smooth, level
oor. The rear should be at least 3’ from any wall. Do not remove the Velcro
belt until you have removed the plastic wrap and Styrofoam from beneath
the unit. Turning the unit on its side after removing the belt may cause
the unit to fold up and cause serious injury!
2
ASSEMBLY STEP 2
114
112
5
99
1. Slide the Console Mast Tube Covers (99 & 112 onto 5 and 98 & 114 onto 4)
onto the left and right Console Mast Tubes. Make sure the holes of 99 & 98
face the outside on each side.
2. Connect the Lower Computer Cable (32) with the Middle Computer Cable
(33) on the right side.
Before attaching the hardware to Step 3, make sure the cables you just connected don’t
get pinched in between the steel tubing. If they do, this may cause issues that prevent
the treadmill from operating properly.
4
98
4
33
32
8S77 TREADMILL
Loading...