Sole E95-2013, E35-2013 Owner’s Manual
TABLEOF T T$
Product Registration
Important Safety Instructions
Important Electrical Information
Important Operation Instructions
Transport Instructions
E35 Assembly Instructions
E95 Assembly Instructions
Elliptical Features
Operation of Your New Elliptical
1
2
3
4
4
16
17
Programmable Features
Using Heart Rate Monitor
General Maintenance
Manufacturer's Limited Warranty
ATTENTION
THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THE
APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
20
25
27
28
,, iiil;;iiiiiiiii_
ii iiiiiii!il
' _,_i_ _i_ iiiiiiiiiiiiiiiii__
°'7 iiiii:iii_
FITNESS
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SOLE FAMILW
Thank you for your purchase of this quality elliptical from SOLE. Your new elliptical has been
manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most
comprehensive warranties available. SOLE will do all we can to make your ownership
experience as pleasant as possible for many years to come.
If you have any questions about your new product or questions about the warranty contact SOLE Fitness
at 1=866=780-SOLE (7653). If you have a technical problem with your new elliptical contact SOLE technical
service at 866-MYSOLE1 (1-866-697-6531).
If you purchased this fitness product from Sears, they will be your contact for all service needs. Please see the
last page in this manual for detailed information about Sears service.To contact Sears for any service issues
call 1-800-4-MY-HOME(I-800-469-4663).
Please take a moment at this time to record below the name of the dealer, their telephone number, and the
date of purchase for easy contact in the future. We appreciate your confidence in SOLE and we will always
remember that you are the reason that we are in business. Please complete and mail your registration card
today and enjoy your new elliptical.
Yours in Health,
SOLE Fitness
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT ST TI
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product
in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soleeilipticais.com under the support tab to register online.
E35_E95_20120907
1 E35 / E95 ELLIPTICAL
IMPORTANT TYI ST UCTI
WARNING - Read all instructions before using this appliance.
DANGER -To reduce the risk of electric shock disconnect your SOLE elliptical from the electrical
outlet prior to cleaning and/or service work.
WARNING -To reduce the risk of burns, fire, electric shock, or injury to persons, install
the elliptical on a fiat level surface with access to a 11O-volt, 15-amp grounded outlet with only
the elliptical plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING
IMPROPER ADAPTERS, OR IN ANYWAY MODIFY THE CORD SET.
A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions, page 3.
II Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet
and elliptical may result.
II Keep children away from the elliptical.There are obvious pinch points and other caution
areas that can cause harm.
II Keep hands away from all moving parts.
II Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working
properly, call your dealer.
II Keep the cord away from heated surfaces.
II Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
II Never drop or insert any object into any openings.
II Do not use outdoors.
II To disconnect, turn all controls to the off position and then remove the plug from the outlet.
II Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
II The hand pulse sensors are not medical devices.Various factors, including the user's move-
ment, may affect the accuracy of heart rate readings.The pulse sensors are intended only as
exercise aids in determining heart rate trends in general.
II Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS =THINK SAFETY!
E3S / EgS ELLIPTICAL 2
iMPORTANTELECTCALl T UCTI
WARNING!
NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your elliptical may be
affected. Such conditions are not covered under your warranty. If you suspect the voltage is
low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this elliptical to rain or moisture.This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment.The operating temperature
specification is 40 to 120 degrees Fahrenheit, and humidity is 95% non-condensing
(no water drops forming on surfaces).
GROUNDINGINSTRUCTIONS
This product must be grounded. If the elliptical should malfunction or breakdown, ground-
ing provides a path of least resistance for electric current, reducing the risk of electric shock.
This product is equipped with a cord having an equipment-grounding plug.The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with
all local codes and ordinances.
DANGER = Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the
product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 11O-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available.The temporary adapter should be used only until a properly grounded
outlet, (shown below) can be installed by a qualified electrician.The green colored rigid ear-lug,
or the like, extending from the adapter, must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a
metal screw.
Grounded Outlet
J
Grounding Pin Grounded Outlet Box
3 E35 / E95 ELLIPTICAL
Adapter
Tab of
.........-_-MetaI Screw Grounding
Screw
IMPORTANTOPERATIONINSTRUCTIONS
II NEVER operate this elliptical without reading and completely understanding the results of
any operational change you request from the computer.
II Understand that changes in resistance and incline do not occur immediately. Set your
desired resistance level on the computer console and release the adjustment key.The
computer will obey the command gradually.
II NEVER use your elliptical during an electrical storm. Surges may occur in your household
power supply that could damage elliptical components. Unplug the elliptical during an
electrical storm as a precaution.
II Use caution while participating in other activities while using your elliptical; such as
watching television, reading, etc.These distractions may cause you to lose balance; which
may result in serious injury.
II Always hold on to a handle bar while making control changes (incline, level, etc.).
II Do not use excessive pressure on console control keys.They are precision set to function
properly with little finger pressure. If you feel the buttons are not functioning properly with
normal pressure contact your SOLE dealer.
POWER CONNECTOR = FRONT, LEFT SIDE OF UNIT
TRANSPORTI ST T
The elliptical is equippped with two transport wheels which are engaged when
the rear of the elliptical is lifted.
E3S / EgS ELLIPTICAL 4
LYPACKCHECKLIST
#180.3/8"x 2T
Split Washer (1 pc)
©
#182.5/16"x 1.5T
Split Washer (4 pcs)
#170.5/16"x 20 x 1.5T
Flat Washer (4 pcs)
#141, M5 x lOmm
Phillips Head Screw (4 pcs)
#183.5/16"
Star Washer (4 pcs)
#181.3/8"x 23 x 2T
Curved Washer (2 pcs)
#157.3/8"x 7T
Nylon Nut (2 pcs)
#132.3/8"x 3/4"
Hex Head Bolt (2 pcs)
#135.5/16"x 2-1/4"
Hex Head Bolt (4 pcs)
#I 25.3/8"x 2-I/4"
Hex Head Bolt (I pc)
#133.3/8"x 1-1/2"
Hex Head Bolt (2 pcs)
5 E35 / E95 ELLIPTICAL
#132.3/8"x 3/4"
HexHeadBolt(2pcs)
#134.5/16"x 1-1/4"
HexHeadBolt(2pcs)
#165.3/8"x 30x 2T
FlatWasher(2pcs)
#175.025
WaveWasher(4 pcs)
#75. Switch Wire Cap
(2 pcs)
#206.3/8"x 2-1/4"
Hex Head Bolt (6 pcs)
#170.5/16"x 20x 1.5T
FlatWasher(2pcs)
#164.3/8" x 19 x 1.ST
Flat Washer (8 pcs)
#159.5/16"x 7T
NylocNut(2pcs)
#157.3/8"x 7T
Nyloc Nut (6 pcs)
#181.3/8"x 23 x 2T
Curved Washer (4 pcs)
#139. M5 x 15mm
Phillips Head Screw (29 pcs)
E35 / E95 ELLIPTICAL 6
#142.3.5 x 12mm
Sheet Metal Screw (18 pcs)
#145. M6x lOmm
Phillips Head Screw (4 pcs)
#184. 13/14mmWrench(160mm)
#185.ShortPhillipsHeadScrewdriver
#186. PhillipsHeadScrewdriver
#187.12/14mmWrench(160mm)
195ASSEMBLYINSTRUCTIONS
PRE-ASSEMBLY
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along
the dotted Line. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing
parts. If damaged parts are found, or parts are missing, contact your dealer
immediately.
3. Locate the hardware package. Remove the tools first. Remove the hardware
for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing
for reference.
7 E35 / E95 ELLIPTICAL
ASSEMBLYINSTRUCTIONS
INCLINE &CONSOLE
See Page 9 for Illustration
1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main
Frame (1). Secure with the six bolts & associated hardware asfollows: From
the sides install two Hex Head Bolts (133) with two Flat Washers (164) and
two Nylon Nuts (157). From the top install four Hex Head Bolts (135), four
Split Washers (182), four Flat Washers (170), and four Star Washers (183), and
tighten with the Wrenches provided (184 & 187).
2. Connect the three wire harness (48) to the female receiver cable coming from
the Incline rail assembly (2). Connect the Three pin position Sensor connec-
tor (49) to the female receiver coming from the Incline rail assembly (2). Mate
red, white, and black wires together.
3. Locate the Console Mast (12) and Console Mast Cover (96) and slide the
cover onto the mast as far as it will go. Make sure the Console Mast Cover is
facing the correct way. At the top opening of the Main Frame of the ellipti-
cal is a Computer Cable (50). Secure the free end of the twist tie that exits
the bottom of the console mast (12) to this cable. Pull the opposite end of
this twist tie up through the Console Mast (12) until the cable exits the top.
Install the Console Mast (12) into the receiving bracket on the top of the Main
Frame (1). Pull slig htly on the Computer Cable at the top of the mast while
installing. This will ensure the cable does not get pinched and shorted during
Console Mast Assembly.
4. Put one Split Washer (180) onto the Long Hex Head Bolt (125) and install
through the left side of the receiving bracket into the Console Mast (12). Put
the two Curved Washers (181) onto the two Short Hex Head Bolts (132) and
install through the front of the console mast. Using Wrench (184), tighten
the (132) bolts first, then the (125) bolt, and lastly the fourth bolt, which is
pre-installed, firmly. These bolts should be tightened as much asyou possibly
can. This is the main joint of the unit. If not tightened sufficiently, this could
lead to noise and instability issues.
5. Plug all of the connectors into the back of the console; Computer Cable (50),
two Hand pulse Cables (57 & 57-1), Resistance switch wire (60) and Incline
switch wire (61). Secure the Console (45) on the console mounting plate with
four Phillips Head Screws (141) using the screw driver (186). Note:therewill beon
empty four pin port on the back of the console. This model doesn't use this port.
I i
#125.3/8"x 2-1/4"
Hex Head Bolt (1 pcs)
#132.3/8"x 3/4"
Hex Head Bolt (2 pcs)
#13:3.3/8"x 1-1/2"
Hex Head Bolt (2 pcs)
#135.5/16"x 2-1/4"
Hex Head Bolt (4 pcs)
#141.M5 x lOmm
Phillips Screw (4 pcs)
#157.3/8"x 7T
Nylon Nut (2 pcs)
#164.3/8" x 19x 1.5T
FlatWasher (2 pcs)
#170.5/16"x 20 x 1.ST
FlatWasher (4 pcs)
#180.3/8"x 2T
Split Washer (1 pc)
#181.3/8"x 23 x 2T
Curved Washer (2 pcs)
#182.5/16"x 1.5T
Split Washer (4 pcs)
#183.5/16"
StarWasher (4 pcs)
LOWER
See Page 9 for illustration
1. Install two Wave Washers (175) onto the Left and Right sides of the Handle
Bar axle.
2. Slide the Left (13) and Right (14) lower arms onto the appropriate side of the
axle.The arms have a small sticker on them indicating L (left) and R(right).
Makesurethehandlebars are facing the correct direction - seeillustration.
3. Install two Flat Washers (165) onto the two Hex Head Bolts, (132) and install
and tighten in the threaded holes in the ends of the axle with a wrench (187).
4. Untie the wire holding the Sleeve Spacer (24) in place on the rod-end of the
Lower Handle Bar Arms (13 & 14). Align the hole in the rod ends with the hole
in the brackets of the left and right Handle Bar (13 & 14).The end of connect-
ing arms should be positioned inside the Handle Bar bracket. Secure with
a Hex Head bolt (134), Flat Washer (170) and Nylon Nut (159) by using the
Wrenches provided (184 & 187)
E35 / E95 ELLIPTICAL 8
S
i
#132.3/8"x 3/4"
Hex Head Bolt (2 pcs)
#134.5/16"x 1-1/4"
Hex Head Bolt (2 pcs)
#159.5/16"x 7T
Nyloc Nut (2 pcs)
#165.3/8"x 30mm
FlatWasher (2 pcs)
#170.5/16"x 20 x 1.ST
FlatWasher (2 pcs)
#175. _25
WaveWasher (4 pcs)
Loading...