SOLE E95 Owner's Manual
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING
YOUR NEW ELLIPTICAL!
2
TABLE OF CONTENTS
Important Safety Instructions 3
Important Electrical Information 4
Important Operation Instructions 5
Transport Instructions 6
Assembly Instructions 9
Elliptical Features 13
Operation of Your New Elliptical 14
Programmable Features 16
Using Heart Rate Monitor 22
General Maintenance 24
Exploded View Diagram 25
Parts List 26
ATTENTION
THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED
FOR THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS
ENTIRETY.
SE598B-YE016_1410(SL)B
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your elliptical from the
electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the elliptical on a flat level surface with access to a 230-volt, 15-amp grounded outlet
with only the elliptical plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 18AWG OR BETTER,
WITH ONLY ONE OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE
GROUNDED PLUG BY USING IMPROPER ADAPTERS, OR IN ANY WAY
MODIFY THE CORD SET.
A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions.
Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both
carpet and elliptical may result.
Keep children away from the elliptical. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not
working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous
environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position and then remove the plug from
the outlet.
Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Various factors, including the
user’s move- ment, may affect the accuracy of heart rate readings. The pulse
sensors are intended only as exercise aids in determining heart rate trends in
general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your elliptical. Quality athletic shoes are recommended to avoid leg
fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
4
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING!
NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your elliptical may
be affected. Such conditions are not covered under your warranty. If you suspect
the voltage is low, contact your local power company or a licensed electrician for
proper testing.
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operating
temperature specification is 40 to 120 degrees Fahrenheit, and humidity is 95%
non-condensing (no water drops forming on surfaces).
GROUNDING INSTRUCTIONS
This product must be grounded. If the elliptical should malfunction or breakdown,
ground- ing provides a path of least resistance for electric current, reducing the risk of
electric shock. This product is equipped with a cord having an equipment-grounding
plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or serviceman if you
are in doubt as to whether the product is properly grounded. Do not modify the
plug provided with the product if it will not fit the outlet; have a proper outlet
installed by a qualified electrician. This product is for use on a nominal 230-volt
circuit, and has a grounding plug.
5
IMPORTANT OPERATION INSTRUCTIONS
NEVER operate this elliptical without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in resistance and incline do not occur immediately. Set
your desired resistance level on the computer console and release the adjustment
key. The computer will obey the command gradually.
NEVER use your elliptical during an electrical storm. Surges may occur in your
household power supply that could damage elliptical components. Unplug the
elliptical during an electrical storm as a precaution.
Use caution while participating in other activities while using your elliptical; such as
watching television, reading, etc. These distractions may cause you to lose balance;
which may result in serious injury.
Always hold on to a handle bar while making control changes (incline, level, etc.).
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure. If you feel the buttons are not functioning
properly with normal pressure contact your dealer.
POWER CONNECTOR - FRONT, LEFT SIDE OF UNIT
TRANSPORT INSTRUCTIONS
The elliptical is equippped with two transport wheels which are engaged when the rear of
the elliptical is lifted.
6
ASSEMBLY PACK CHECKLIST
1
HARDWARE STEP 1
#164. 3/8” x 19 x 1.5T
Flat Washer (2 pcs)
#170
. 5/16” x 20 x 1.5T
Flat Washer (4 pcs)
#181
. 3/8” x 23 x 2T
Curved Washer (2 pcs)
#180
. 3/8” x 2T
Split Washer (1 pc)
#141.
M5 x 10mm
Phillips Head Screw (4 pcs)
#157
. 3/8” x 7T
Nylon Nut (2 pcs)
#182
. Ø 5/16” x 1.5T
Split Washer (4 pcs)
#183
. Ø 5/16”
Star Washer (4 pcs)
#132
. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#135
. 5/16” x 2-1/4”
Hex Head Bolt (4 pcs)
#133
. 3/8” x 1-1/2”
Hex Head Bolt (2 pcs)
#125
. 3/8” x 2-1/4”
Hex Head Bolt (1 pc)
7
#175
. Ø25
Wave Washer (4 pcs)
#206
. 3/8” x 2-1/4”
Hex Head Bolt (6 pcs)
#181
. 3/8” x 23 x 2T
Curved Washer (4 pcs)
#139
. M5 x 15mm
Phillips Head Screw
(29 pcs)
#142
. Ø 3.5 x 12mm
Sheet Metal Screw
(18 pcs)
#145
. M6 x 10mm
Phillips Head Screw
(4 pcs)
2
HARDWARE STEP 2
3
HARDWARE STEP 3
4
HARDWARE STEP 4
#132
. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#134
. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
# 165. 3/8” x 30 x 2T
Flat Washer (2 pcs)
#170.
5/16” x 20 x 1.5T
Flat Washer (2 pcs)
#159
. 5/16” x 7T
Nyloc Nut (2 pcs)
#75. Switch Wire Cap
(2 pcs)
#164
. 3/8” x 19 x 1.5T
Flat Washer (8 pcs)
#157
. 3/8” x 7T
Nyloc Nut (6 pcs)
8
#184. 13/14mm Wrench (160mm) #185. Short Phillips Head Screwdriver
#186. Phillips Head Screwdriver #187. 12/14mm Wrench (160mm)
ASSEMBLY TOOLS
ASSEMBLY INSTRUCTIONS
PRE-ASSEMBLY
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along
the dotted Line. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or
missing parts. If damaged parts are found, or parts are missing, contact your
dealer immediately.
3. Locate the hardware package. Remove the tools first. Remove the hardware
for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing
for reference.
9
#125. 3/8” x 2-1/4”
Hex Head Bolt (1 pcs)
#132. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#133. 3/8” x 1-1/2”
Hex Head Bolt (2 pcs)
#135. 5/16” x 2-1/4”
Hex Head Bolt (4 pcs)
#141. M5 x 10mm
Phillips Screw (4 pcs)
#157. 3/8” x 7T
Nylon Nut (2 pcs)
#164. 3/8” x 19 x 1.5T
Flat Washer (2 pcs)
#170. 5/16” x 20 x 1.5T
Flat Washer (4 pcs)
#180. 3/8” x 2T
Split Washer (1 pc)
#181. 3/8” x 23 x 2T
Curved Washer (2 pcs)
#182. Ø 5/16” x 1.5T
Split Washer (4 pcs)
#183. Ø 5/16”
Star Washer (4 pcs)
#132. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#134. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
#159. 5/16” x 7T
Nyloc Nut (2 pcs)
#165. 3/8” x 30 x 2T
Flat Washer (2 pcs)
#170. 5/16” x 20 x 1.5T
Flat Washer (2 pcs)
#175. Ø25
Wave Washer (4 pcs)
ASSEMBLY INSTRUCTIONS
1
INCLINE RAIL & CONSOLE MAST
HARDWARE STEP 1
1. Install the Incline Rail Assembly (2) into the U-channel bracket of the
Main Frame (1). Secure with the six bolts & associated hardware as
follows: From the sides install two Hex Head Bolts (133) with two
Flat Washers (164) and two Nylon Nuts (157). From the top install
four Hex Head Bolts (135), four Split Washers (182), four Flat
Washers (170), and four Star Washers (183), and tighten with the
Wrenches provided (184 & 187).
2. Connect the three wire harness (48) to the female receiver cable
coming from the Incline rail assembly (2). Connect the Three pin
position Sensor connec- tor (49) to the female receiver coming from
the Incline rail assembly (2). Mate red, white, and black wires
together.
3. Locate the Console Mast (12) and Console Mast Cover (96) and
slide the cover onto the mast as far as it will go. Make sure the
Console Mast Cover is facing the correct way. At the top opening of
the Main Frame of the ellipti- cal is a Computer Cable (50). Secure
the free end of the twist tie that exits the bottom of the console mast
(12) to this cable. Pull the opposite end of this twist tie up through
the Console Mast (12) until the cable exits the top.
Install the Console Mast (12) into the receiving bracket on the top of
the Main Frame (1). Pull slightly on the Computer Cable at the top of
the mast while installing. This will ensure the cable does not get
pinched and shorted during Console Mast Assembly.
4. Put one Split Washer (180) onto the Long Hex Head Bolt (125) and
install through the left side of the receiving bracket into the Console
Mast (12). Put the two Curved Washers (181) onto the two Short
Hex Head Bolts (132) and install through the front of the console
mast. Using Wrench (184), tighten the (132) bolts first, then the
(125) bolt, and lastly the fourth bolt, which is pre-installed, firmly. These bolts should be
tightened as much as you possibly can. This is the main joint of the unit. If not tightened
sufficiently, this could lead to noise and instability issues.
5. Plug all of the connectors into the back of the console; Computer Cable (50), two Hand
pulse Cables (57 & 57-1), Resistance switch wire (60) and Incline switch wire (61). Secure
the Console (45) on the console mounting plate with four Phillips Head Screws (141) using
the screw driver (186). Note: there will be an empty four pin port on the back of the console.
This model doesn’t use this port.
2
LOWER HANDLE BAR ARMS
HARDWARE STEP 2
1. Install two Wave Washers (175) onto the Left and Right sides of the
Handle Bar axle.
2. Slide the Left (13) and Right (14) lower arms onto the appropriate
side of the axle. The arms have a small sticker on them indicating L
(left) and R (right). Make sure the handlebars are facing the correct
direction – see illustration.
3. Install two Flat Washers (165) onto the two Hex Head Bolts, (132)
and install and tighten in the threaded holes in the ends of the axle
with a wrench (187).
4. Untie the wire holding the Sleeve Spacer (24) in place on the
rod-end of the Lower Handle Bar Arms (13 & 14). Align the hole in
the rod ends with the hole in the brackets of the left and right Handle Bar (13 & 14). The end
of connect- ing arms should be positioned inside the Handle Bar bracket. Secure with a Hex
Head bolt (134), Flat Washer (170) and Nylon Nut (159) by using the Wrenches provided
(184 & 187)
Loading...