Sole E35-2010, E25-2010 Owner’s Manual

FmTNESS

0 WNER'S MANUA L

PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE

OPERA TING YOUR NEW ELLIPTICAL!

Product Registration ..................................................................................... 2

Important Safety Instructions ........................................................................... 3

Important Electrical Information ........................................................................ 4

Important Operation Instructions ....................................................................... 5

E25 Assembly Instructions ............................................................................... 6

E35 Assembly Instructions ............................................................................... 15

Operation of Your New Elliptical ........................................................................ 25

Maintenance ................................................................................................. 34

Manufacturer's Limited Warranty ....................................................................... 35

ATTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE

ONLYAND IS WARRANTED FOR THATAPPLICATION. ANY OTHER

APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.

1 E25 / E35 Elliptical

LIE

FmTNES$

CONGRATULATIONS ON YOUR

NEW ELLIPTICAL AND WELCOME

TO THE SOLE FAMILW

Thank you for your purchase of this quality elliptical trainer from SOLE. Your new elliptical has been manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. SOLE will do all we can to make your ownership experience as pleasant as possible for many years to come.

If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1-866-780-SOLE (7653). If you have a technical problem with your new elliptical contact SOLE technical service at 866-MYSOLE1 (697-6531)

Please take a moment at this time to record the name of the dealer, their telephone number, and the date of purchase below to make any future, needed contact easy. We appreciate your support and we will always remember that you are the reason that we are in business. Please complete and mail your registration card today and enjoy your new elliptical.

Yours in Health, SOLE Fitness

Name of Dealer

Telephone Number of Dealer

Purchase Date

RECORD YOUR SERIAL NUMBER

Please record the Serial Number of this fitness product in the space provided below.

Serial Number

or visit www.Soletreadmills.com under the support tab to register online.

E25 / E35 2009 ver. B

2 E25 / E35 Elliptical

WARNING - Read all instructions before using this appliance.

These three warninqs paraqraphs are for E35 owners:

DANGER - To reduce the risk of electric shock disconnect your SOLE E35 elliptical from

the electrical outlet prior to cleaning and/or service work.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install

the elliptical on a flat level surface with access to a nominal 110-volt, 15-amp grounded outlet with only the E35 elliptical plugged into the circuit..

DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY

ONE OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG

BY USING IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions, page 4.

• Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both the carpet and elliptical may result.

Keep children away from the elliptical. There are obvious pinch points, moving parts

and other caution areas that can cause harm.

• Keep hands away from all moving parts.

• Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly, call your dealer.

• Keep the cord away from heated surfaces.

• Do not operate where aerosol spray products are being used or where oxygen is

being administered. Sparks from the motor could ignite a highly gaseous environment

• Never drop or insert any object into any openings.

• Do not use outdoors.

• To disconnect, turn all controls to the off position, then remove the plug from the outlet.

• Do not attempt to use your elliptical for any purpose other than for the purpose it is

intended.

• The hand pulse sensors are not medical devices. Various factors, including the user's movement, may affect the accuracy of heart rate readings. The pulse sensors are

intended only as exercise aids in determining heart rate trends in general.

• Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

3 E25 / E35 Elliptical

WARNING!

• NEVER remove any cover without first disconnecting AC power supply.

• If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect

the voltage is low, contact your local power company or a licensed electrician for proper testing.

• NEVER expose this elliptical to rain or moisture. This product is NOT designed for use outdoors, near a pool or spa, or in any other environment that may cause the machine to get wet. The maximum operating temperature specification is 40 degrees C (104 F), and

humidity is 95% non-condensing (no water drops forming on surfaces).

This product must be grounded. If the E35's electrical system should malfunction or breakdown grounding provides a path of least resistance for electric current, reducing the risk of electric shock. This product is equipped with a cord having an equipment-grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock, Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product if it will not fit the outlet; have a proper outlet installed by a qualified electrician,

This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like the plug illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available. The temporary adapter should be used only until a properly

grounded outlet, (shown below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the like, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw.

Grounded Outlet

Adapter

Screw

Tab of

Grounding

Screw

Grounding Pin

Grounded Outlet Box

4 E25 / E35 Elliptical

• NEVER operate this elliptical without reading and completely understanding the results of

any operational change you request from the computer.

• Understand that changes in resistance do not occur immediately. Set your desired level

on the computer console and release the adjustment key. The computer will obey the command gradually.

• NEVER use your elliptical during an electrical storm. Surges may occur in your household

power supply due to lightening strikes that could damage elliptical components. Unplug

the elliptical during an electrical storm as a precaution.

• Use caution while participating in other activities while using your elliptical such as

watching television, reading, etc. These distractions may cause you to lose balance which may result in serious injury.

• Always hold on to a handrail or hand bar while making control changes.

Do not use excessive pressure on console control keys. They are precision set to properly function with little finger pressure. If you feel the buttons are not functioning properly with normal pressure, contact your SOLE dealer.

POWER CONNECTOR LOCATED ON FRONT, LEFT HAND SIDE OF UNIT.

[Transportation]

The elliptical is equipped with two transport wheels which are engaged when rear of the Elliptical is lifted.

5 E25 / E35 Elliptical

#142.3/8"x 19 x 1.5T Flat Washer (2pcs)

#157.5/16"x 20x 1.5T

Flat Washer (4 pcs)

#156.3/8"x 23 x 2T

Curved Washer (2pcs)

#155.3/8" x 2T

Split Washer (1 pc)

#158. ku 5/16" x 1.5T

Split Washer (4pcs)

#108.5/16" x 2-1/4"

Hex Head Bolt (4 pcs)

#117. M5 xl0mm

Phillips Head Screw (4 pcs)

#151. ku 5/16"

Star Washer (4pcs)

#134.3/8" x 7T

Nylon Nut (2 pcs)

#106.3/8" x 3/4"

Hex Head Bolt (2pcs)

#107.3/8" x 1-1/2"

Hex Head Bolt (2pcs)

#101.3/8" x 2-1/4"

Hex Head Bolt (1pc)

6 E25 / E35 Elliptical

#153. ku17mm

Wave Washer (2 pcs)

#145.5/16" x 23 x 1.5T

Flat Washer (2 pcs)

#126.ku 3.5 x 12mm

Sheet Metal Screw (6 pcs)

#151.5/16"x 20 x 1.5T

Flat Washer (2 pcs)

#137.5/16" x 7T

Nylon Nut (2 pcs)

#100.5/16" x 15mm

Hex Head Bolt (2 pcs)

#109.5/16" x 1-1/4"

Hex Head Bolt (2 pcs)

#126. ku3.5 x 12mm Sheet Metal Screw (2pcs)

#115. M5 x 15mm

Phillips Head Screw (20 pcs)

7 E25 / E35 Elliptical

#125. M6 x 10mm

Phillips Head Screw (4 pcs)

#161. Phillips Screw Driver (1 pc) #160. Short Screw Driver (1 pc)

#162.12/14 mm Wrench (1 pc)

#159. 13/14mm Wrench (1pc)

8 E25 / E35 Elliptical

• UNPACKING THE UNIT

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately.

3. Locate the hardware package. The hardware is separated into four steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing for

reference.

STEP 1: Incline Rail Assembly and Console Mast

1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main Frame (1). Secure with the six bolts & associated hardware as follows: From the sides install

two 3/8"x1-1/2" Hex Head Bolts (107) with two 3/8"x19mm Flat Washers (142) and two 3/8"x7T Nylon Nuts (134). From the top install four 5/16"x2-1/4" Hex Head Bolts (108), four 5/16" Split Washers (158), four 5/16"x20 Flat Washers (157) and four Star Washers (151), as shown in figure 1, and tighten with the 13/14 mm Wrench (159) and 12/14 mm Wrench (162).

2. Locate the Console Mast (12) and Console Mast Cover (72) and slide the Cover onto the Mast as far as it will go. Make sure the Console Mast Cover is facing the correct way. At the top opening of the Main Frame of the elliptical is a computer cable (47). Unravel and straighten out the cable and feed it into the bottom of the console mast tube and out of the top opening. Install the Console Mast (12) into the receiving bracket on the top of the Main Frame. Pull slightly on the computer cable at the top

of the mast while installing. This will ensure the cable does not get pinched and shorted during console mast assembly.

3. Put one 3/8" x 2T Split Washer (155) onto the 3/8" x 2-1/4" Long Hex Head Bolt (101) and install through the left side of the receiving bracket into the Console Mast (12).

Put the two 3/8" x 23 Curved Washers (156) onto the two 3/8" x 3/4" Short Hex Head Bolts (106) and install through the front of the console mast. Using the 13/14m/m Wrench, tighten the three bolts, and the fourth bolt which is pre-installed,

firmly. These bolts should be tightened as much as you possibly can.

4. Plug all of the connectors into the back of the console; Computer Cable (47), two

Hand pulse Cables (52) and Resistance switch wires (55). Secure the Console (46)

on the console mounting plate with four M5xl0m/m Phillips Head Screws (117).

9 E25 / E35 Elliptical

101 .... _.

158

108

142

154

10 E25 / E35 Elliptical

+ 25 hidden pages