SOLE E20,E25 Owner's Manual
OWNER’S MANUAL
E20 / E25 Elliptical Trainer
Please carefully read this entire manual
before operating your new elliptical.
TABLE OF CONTENTS
Product Registration
Important Safety Instructions
Important Electrical Information
Important Operation Instructions
Transport Instructions
E20 Assembly Instructions
E25 Assembly Instructions
Elliptical Features
Operation of Your New Elliptical
1
2
3
4
4
7
12
16
17
Programmable Features
Using Heart Rate Monitor
General Maintenance
Manufacturer’s Limited Warranty
ATTENTION
THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THE
APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
20
25
27
28
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SOLE FAMILY!
Thank you for your purchase of this quality elliptical from SOLE. Your new elliptical has been
manufactured by one of the leading tness manufacturers in the world and is backed by one of the most
comprehensive warranties available. SOLE will do all we can to make your ownership
experience as pleasant as possible for many years to come.
If you have any questions about your new product or questions about the warranty contact SOLE Fitness
at 1-866-780-SOLE (7653). If you have a technical problem with your new elliptical contact SOLE technical
service at 866-MYSOLE1 (1-866-697-6531).
Please take a moment at this time to record below the name of the dealer, their telephone number, and the
date of purchase for easy contact in the future. We appreciate your condence in SOLE and we will always
remember that you are the reason that we are in business. Please complete and mail your registration card
today and enjoy your new elliptical.
Yours in Health,
SOLE Fitness
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT REGISTRATION
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this tness product
in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soleellipticals.com under the support tab to register online.
E20_E25_20140328
E20 / E25 ELLIPTICAL1
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your SOLE elliptical from the electrical
outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons, install
the elliptical on a at level surface with access to a 110-volt, 15-amp grounded outlet with only
the elliptical plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING
IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET.
A serious shock or re hazard may result along with computer malfunctions. See Grounding Instructions, page 3.
Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet
and elliptical may result.
Keep children away from the elliptical. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working
properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the o position and then remove the plug from the outlet.
Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Various factors, including the user’s move-
ment, may aect the accuracy of heart rate readings. The pulse sensors are intended only as
exercise aids in determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
2E20 / E25 ELLIPTICAL
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING!
NEVER remove any cover without rst disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your elliptical may be
aected. Such conditions are not covered under your warranty. If you suspect the voltage is
low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment. The operating temperature
specication is 40 to 120 degrees Fahrenheit, and humidity is 95% non-condensing
(no water drops forming on surfaces).
GROUNDING INSTRUCTIONS
This product must be grounded. If the elliptical should malfunction or breakdown, grounding provides a path of least resistance for electric current, reducing the risk of electric shock.
This product is equipped with a cord having an equipment-grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with
all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the
product if it will not t the outlet; have a proper outlet installed by a qualied electrician.
This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below
may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available. The temporary adapter should be used only until a properly grounded
outlet, (shown below) can be installed by a qualied electrician. The green colored rigid ear-lug,
or the like, extending from the adapter, must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a
metal screw.
E20 / E25 ELLIPTICAL3
IMPORTANT OPERATION INSTRUCTIONS
NEVER operate this elliptical without reading and completely understanding the results of
any operational change you request from the computer.
Understand that changes in resistance and incline do not occur immediately. Set your
desired resistance level on the computer console and release the adjustment key. The
computer will obey the command gradually.
NEVER use your elliptical during an electrical storm. Surges may occur in your household
power supply that could damage elliptical components. Unplug the elliptical during an
electrical storm as a precaution.
Use caution while participating in other activities while using your elliptical; such as
watching television, reading, etc. These distractions may cause you to lose balance; which
may result in serious injury.
Always hold on to a handle bar while making control changes (incline, level, etc.).
Do not use excessive pressure on console control keys. They are precision set to function
properly with little nger pressure. If you feel the buttons are not functioning properly with
normal pressure contact your SOLE dealer.
POWER CONNECTOR - FRONT, LEFT SIDE OF UNIT
TRANSPORT INSTRUCTIONS
The elliptical is equippped with two transport wheels which are engaged when
the rear of the elliptical is lifted.
4E20 / E25 ELLIPTICAL
1
E20 /25 ASSEMBLY PACK CHECKLIST
HARDWARE STEP 1 (E20)
1
#112. 3/8” x 3-3/4”
Hex Head Bolt
(4 pcs)
#139. 3/8” x 19mm x 1.5T
Flat Washer
(4 pcs)
#113. 3/8” x 3/4”
Socket Head Cap Bolt
#142. 3/8” x 2T
Split Washer
HARDWARE STEP 1 (E25)
(4 pcs)
(8 pcs)
#119. M5 x 10mm
Phillips Head Screw
(4 pcs)
#144. 3/8” x 23 x 2T
Curved Washer
(4 pcs)
#109. 3/8” x 2-1/4”
Hex Head Bolt
(3 pcs)
#119. M5 x 10mm
Phillips Head Screw
(4 pcs)
#110. 3/8” x 3/4”
Hex Head Bolt
(2 pcs)
#139. 3/8” x 19mm x 1.5T
Flat Washer
(2 pcs)
#112. 3/8 x 3-3/4”
#142. 3/8” x 2T
Split Washer
(5 pcs)
Hex Head Bolt
(2 pcs)
#144. 3/8” x 23 x 2T
Curved Washer
(4 pcs)
E20 / E25 ELLIPTICAL5
2
HARDWARE STEP 2
3
4
#104. 5/16” x 15mm
Hex Head Bolt (2 pcs)
#115. 5/16” x 15mm
Button Head Socket Bolt (2 pcs)
HARDWARE STEP 3
#106. 5/16” x 1-3/4”
Hex Head Bolt (6 pcs)
#129. 5/16” x 7T
Nyloc Nut (6 pcs)
HARDWARE STEP 4 (E20)
#138. Ø8.5 × 26mm × 2T
Flat Washer (4 pcs)
#143. 5/16” x 23mm x 1.5T
Curved Washer (4 pcs)
4
#120. M5 x 15mm
Phillips Head Screw (4 pcs)
#122. Ø3.5 x 12mm
Sheet Metal Screw (6 pcs)
HARDWARE STEP 4 (E25)
#120. M5 x 15mm
Phillips Head Screw (15 pcs)
#122. Ø3.5 x 12mm
Sheet Metal Screw (8 pcs)
6E20 / E25 ELLIPTICAL
#100. Switch Wire Cap
(2 pcs)
ASSEMBLY TOOLS
#149. M5 Allen Wrench
& Phillips Head Screw Driver
#151. 13/14mm
Wrench (160mm)
#150. Phillips Head Screwdriver
#153. M8 L Allen Wrench
(E20 Only)
#152. 12/14mm
Wrench (160mm)
E20 / 25 ASSEMBLY INSTRUCTIONS
PRE-ASSEMBLY
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along
the dotted Line. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing
parts. If damaged parts are found, or parts are missing, contact your dealer
immediately.
3. Locate the hardware package. Remove the tools rst. Remove the hardware
for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing
for reference.
E20 / E25 ELLIPTICAL7
E20 ASSEMBLY INSTRUCTIONS
1
2
STABILIZERS & CONSOLE MAST
See Page 9 for Illustration
1. Connect the Front Stabilizer Bar (2) with the Main Frame at the front joining
plate by using the Wrench (151) to tighten two Hex Head Bolts (112) , two
Split Washers (142) and two Curved Washers (144).
2. Connect the Rear Stabilizer (3) with the Main Frame at the rear joining plate
by using the Wrench (151) to tighten two Hex Head Bolts (112) , two Split
Washers (142) and two Curved Washers (144).
3. Pull the wire, which is attached to the Computer Cable (38), out of Console
Mast (15) and secure the mast on the Main Frame by using the M8 L Allen
Wrench (153) to tighten four Socket Head Cap Bolts (113) together with four
Split Washers (142) and four Flat Washers (139).
4. Plug in the connectors of the Computer Cable (38) and two Handpulse with
Cable Assemblies (White & Red) (44, 45) on the back of the Console Assembly
(35) and secure the Console Assembly (35) on the console holding plate with
four Phillips Head Screws (119) by tightening them with Phillips Head Screw
Driver (150).
LOWER SWING ARMS
See Page 9 for Illustration
1. Attach the Lower Swing Arms (L) and (R), (12) and (13), on each side of
Console Mast shaft and secure with two Hex Head Bolts (104) and two Flat
Washers (138) by using the Wrench (152).
2. Insert the shaft of the left Connecting Arm (10) through the bushing on left
Pedal Arm (7) and secure with a Button Head Socket Bolt (115) together with
a Flat Washer (138) by using M5 L Allen Wrench (149). Do it the same way for
right Connecting Arm (11) and right Pedal Arm (8).
3. Remove the Rod End Shaft (20), Flat Washer (136) and Hex Head Bolt (104)
which are on the left and right Connecting Arms. Connect the Connecting
Arm with the Lower Swing Arm and secure with Rod End Shaft (20), Flat
Washer (136) and the Hex Head Bolt (104) by using the Wrench provided
(152).
HARDWARE STEP 1
#112. 3/8” x 3-3/4” Hex
Head Bolt (4 pcs)
#113. 3/8” x 3/4”
Socket Head Cap Bolt
(4 pcs)
#119. M5 x 10mm
Phillips Head Screw
(4 pcs)
#139. 3/8” x 19mm x
1.5T Flat Washer (4 pcs)
#142. 3/8” x 2T
Split Washer (8 pcs)
#144. 3/8” x 23 x 2T
Curved Washer (4 pcs)
HARDWARE STEP 2
#104. 5/16” x 15mm
Hex Head Bolt (2 pcs)
#115. 5/16” x 15mm
Button Head Socket Bolt
(2 pcs)
#138. Ø8.5 × 26mm ×
2.0T Flat Washer (4 pcs)
8E20 / E25 ELLIPTICAL
Loading...