Sole E25-2013, E20-2013 Owner’s Manual

TABLEOF T T$

Product Registration

Important Safety Instructions

Important Electrical Information

Important Operation Instructions

Transport Instructions

E20 Assembly Instructions

E25 Assembly Instructions

Elliptical Features

Operation of Your New Elliptical

1

2

3

4

4

16

17

Programmable Features

Using Heart Rate Monitor

General Maintenance

Manufacturer's Limited Warranty

ATTENTION

THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THE
APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.

20

25

27

28

,, iiil;;iiiiiiiii_

ii iiiiiii!il

' _,_i_ _i_ iiiiiiiiiiiiiiiii__

°'7 iiiii:iii_

FITNESS

CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SOLE FAMILW

Thank you for your purchase of this quality elliptical from SOLE. Your new elliptical has been

manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most
comprehensive warranties available. SOLE will do all we can to make your ownership
experience as pleasant as possible for many years to come.

If you have any questions about your new product or questions about the warranty contact SOLE Fitness
at 1=866=780-SOLE (7653). If you have a technical problem with your new elliptical contact SOLE technical

service at 866-MYSOLE1 (1-866-697-6531).

If you purchased this fitness product from Sears, they will be your contact for all service needs. Please see the
last page in this manual for detailed information about Sears service.To contact Sears for any service issues
call 1-800-4-MY-HOME(I-800-469-4663).

Please take a moment at this time to record below the name of the dealer, their telephone number, and the
date of purchase for easy contact in the future. We appreciate your confidence in SOLE and we will always
remember that you are the reason that we are in business. Please complete and mail your registration card

today and enjoy your new elliptical.

Yours in Health,

SOLE Fitness

Name of Dealer

Telephone Number of Dealer

Purchase Date

PRODUCT ST TI

RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product

in the space provided below.

Serial Number

REGISTER YOUR PURCHASE

The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soleeilipticais.com under the support tab to register online.

E20_E25_20121214

1 E20 / E25 ELLIPTICAL

IMPORTANT TYI ST UCTI

WARNING - Read all instructions before using this appliance.

DANGER -To reduce the risk of electric shock disconnect your SOLE elliptical from the electrical

outlet prior to cleaning and/or service work.

WARNING -To reduce the risk of burns, fire, electric shock, or injury to persons, install

the elliptical on a fiat level surface with access to a 11O-volt, 15-amp grounded outlet with only
the elliptical plugged into the circuit.

DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING

IMPROPER ADAPTERS, OR IN ANYWAY MODIFY THE CORD SET.

A serious shock or fire hazard may result along with computer malfunctions. See Grounding Instructions, page 3.

II Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet

and elliptical may result.

II Keep children away from the elliptical.There are obvious pinch points and other caution

areas that can cause harm.

II Keep hands away from all moving parts.
II Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working

properly, call your dealer.

II Keep the cord away from heated surfaces.
II Do not operate where aerosol spray products are being used or where oxygen is being

administered. Sparks from the motor may ignite a highly gaseous environment.

II Never drop or insert any object into any openings.
II Do not use outdoors.

II To disconnect, turn all controls to the off position and then remove the plug from the outlet.
II Do not attempt to use your elliptical for any purpose other than for the purpose it is

intended.

II The hand pulse sensors are not medical devices.Various factors, including the user's move-

ment, may affect the accuracy of heart rate readings.The pulse sensors are intended only as
exercise aids in determining heart rate trends in general.

II Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on

your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.

SAVE THESE INSTRUCTIONS =THINK SAFETY!

E20 / E25 ELLIPTICAL 2

iMPORTANTELECTCALl T UCTI

WARNING!

NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your elliptical may be

affected. Such conditions are not covered under your warranty. If you suspect the voltage is
low, contact your local power company or a licensed electrician for proper testing.

NEVER expose this elliptical to rain or moisture.This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment.The operating temperature
specification is 40 to 120 degrees Fahrenheit, and humidity is 95% non-condensing

(no water drops forming on surfaces).

GROUNDINGINSTRUCTIONS

This product must be grounded. If the elliptical should malfunction or breakdown, ground-
ing provides a path of least resistance for electric current, reducing the risk of electric shock.

This product is equipped with a cord having an equipment-grounding plug.The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

DANGER = Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to

whether the product is properly grounded. Do not modify the plug provided with the
product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 11O-volt circuit, and has a grounding plug that looks like
the plug illustrated below. A temporary adapter that looks like the adapter illustrated below

may be used to connect this plug to a 2-pole receptacle as shown below if a properly grounded
outlet is not available.The temporary adapter should be used only until a properly grounded

outlet, (shown below) can be installed by a qualified electrician.The green colored rigid ear-lug,
or the like, extending from the adapter, must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a

metal screw.

Grounded Outlet

J

Grounding Pin Grounded Outlet Box

3 E20 / E25 ELLIPTICAL

Adapter

Tab of

.........-_-MetaI Screw Grounding

Screw

IMPORTANT T I T

II NEVER operate this elliptical without reading and completely understanding the results of

any operational change you request from the computer.

m Understand that changes in resistance and incline do not occur immediately. Set your

desired resistance level on the computer console and release the adjustment key.The
computer will obey the command gradually.

m NEVER use your elliptical during an electrical storm. Surges may occur in your household

power supply that could damage elliptical components. Unplug the elliptical during an
electrical storm as a precaution.

m Use caution while participating in other activities while using your elliptical; such as

watching television, reading, etc.These distractions may cause you to lose balance; which

may result in serious injury.
m Always hold on to a handle bar while making control changes (incline, level, etc.).
m Do not use excessive pressure on console control keys.They are precision set to function

properly with little finger pressure. If you feel the buttons are not functioning properly with

normal pressure contact your SOLE dealer.

POWER CONNECTOR - FRONT, LEFT SIDE OF UNIT

TRANSPORTI ST T

The ellipticalisequippped with two transportwheels which are engaged when

the rear of the elliptical is lifted.

E20 / E25 ELLIPTICAL 4

LYPACKCHECKLIST

#112.3/8"x 3-3/4"

Hex Head Bolt (4 pcs)

#119. M5 x lOmm

Phillips Head Screw (4 pcs)

#142.3/8"x 2T

Split Washer (8 pcs)

#113.3/8"x 3/4"

Socket Head Cap Bolt (4 pcs)

#139.3/8"x 19mm x 1.5T

Flat Washer (4 pcs)

#144.3/8"x 23 x 2T

Curved Washer (4 pcs)

5 E20 / E25 ELLIPTICAL

#104.5/16"x 15mm

HexHeadBolt(2pcs)

#115.5/16"x 15mm

ButtonHeadSocketBolt(2pcs)

#138.08.5 x 26mmx 2T

FlatWasher(4pcs)

#106.5/16"x 1-3/4"

HexHeadBolt(6pcs)

#129.5/16"x 7T

NylocNut(6pcs)

HARDWARESTEP4[E20_

#120. M5 x 15mm

Phillips Head Screw (4 pcs)

#122. 03.5 x 12mm

Sheet Metal Screw (6 pcs)

HARDWARESTEP4{E25)

#143.5/16"x 23mmx 1.5T

CurvedWasher(4pcs)

#120. M5 x 15mm

Phillips Head Screw (7 pcs)

E20 / E25 ELLIPTICAL 6

#122. 03.5 x 12mm

Sheet Metal Screw (8 pcs)

#100. Switch Wire Cap

(2 pcs)

#149.MSLAllenWrench

#150. PhillipsHeadScrewdriver

#151.13/14mm

#15:3.M8LAllenWrench

Wrench(160mm)

ASSEMBLYINSTRUCTIONS

PRE-ASSEMBLY

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along
the dotted Line. Lift Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing
parts. If damaged parts are found, or parts are missing, contact your dealer
immediately.

3. Locate the hardware package. Remove the tools first. Remove the hardware
for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing

for reference.

7 E20 / E25 ELLIPTICAL

#152.12/14mm

Wrench(160mm)

ASSEMLYINSTRUCTIONS

&CONSOLE

See Page 9 for Illustration

1. Connect the Front Stabilizer Bar (2) with the Main Frame at the front joining
plate by using the Wrench (1S1) to tighten two Hex Head Bolts (112), two
Split Washers (142) and two Curved Washers (144).

2. Connect the Rear Stabilizer (3) with the Main Frame at the rear joining plate
by using the Wrench (151) to tighten two Hex Head Bolts (112), two Split

Washers (142) and two Curved Washers (144).

3. Pull the wire, which is attached to the Computer Cable (38), out of Console
Mast (1S) and secure the mast on the Main Frame by using the M8 L Allen
Wrench (1S3) to tighten four Socket Head Cap Bolts (113) together with four
Split Washers (142) and four Flat Washers (139).

4. Plug in the connectors of the Computer Cable (38) and two Handpulse with
Cable Assemblies (White & Red) (44, 45) on the back of the Console Assembly
(3S) and secure the Console Assembly (3S) on the console holding plate with
four Phillips Head Screws (119) by tightening them with Phillips Head Screw

Driver (150).

• i

#112.3/8"x 3-3/4" Hex

Head Bolt (4 pcs)

#11:3.3/8"x 3/4"
Socket Head Cap Bolt

(4 pcs)
#119. M5 x lOmm

Phillips Head Screw

(4 pcs)
#1:39.3/8"x 19mm x

1.5T Flat Washer (4 pcs)

#142.3/8"x 2T
Split Washer (8 pcs)

#144.3/8"x 23 x 2T
Curved Washer (4 pcs)

LOWER

See Page 9 for illustration

1. Attach the Lower Swing Arms (L) and (R), (12) and (13), on each side of
Console Mast shaft and secure with two Hex Head Bolts (104) and two Flat

Washers (138) by using the Wrench (1S2).

2. Insert the shaft of the left Connecting Arm (10) through the bushing on left
Pedal Arm (7) and secure with a Button Head Socket Bolt (115) together with
a Flat Washer (138) by using M5 L Allen Wrench (149). Do it the same way for
right Connecting Arm (11) and right Pedal Arm (8).

3. Remove the Rod End Shafts (20) which are pre-assembled on the left and
right Connecting Arms. Assemble the Connecting Arm with the Lower Swing
Arm and secure with Rod End Shafts (20) and the screw by using the M5 L

Allen Wrench (149).

#104.5/16"x 15mm

Hex Head Bolt (2 pcs)

#11S. 5/16"x 15mm

Button Head Socket Bolt

(2 pcs)
#138. D8.5 x 26mm x 2T

FlatWasher (4 pcs)

E20 / E25 ELLIPTICAL 8