Sole R92-2011, B94-2011 Owner’s Manual

PLEASE CAREFULLY READTHIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW FITNESS BIKE

TALEOF T

Product Registration 1

Important Safety Instruction_ 2

Important Electrical Information 3

Important Operation Instructions 3

B94 Assembly Instructions 5

R92 Assembly Instructions 11

Fitness Bike Features 15

Operation of Your New Fitness Bike 16

Programmable Features 19

Using Heart Rate Monitor 24

General Maintenance 26

Manufacturer's Limited Warranty 27

ATTENTION

THIS FITNESSBIKEISINTENDED FOR RESIDENTIAL USE ONLY AND ISWARRANTED FOR THEAPPLICATION. ANY OTHERAPPLICATION VOIDS THIS WARRANTY IN ITSENTIRETY.

T N E S S

CONGRATULATIONS ON YOUR NEW FITNESS BIKE AND WELCOME TO THE SOLE FAMILW

Thank you for your purchase of this quality fitness bike from SOLE. Your new fitness bike has been

manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. SOLE will do all we can to make your ownership

experience as pleasant as possible for many years to come.

If you have any questions about your new product or questions about the warranty contact SOLE Fitness at 1=866=780=SOLE {7653}. If you have a technical problem with your new fitness bike contact SOLE technical service at 866-MYSOLEI (697-6531).

Please take a moment at this time to record below the name of the dealer, their telephone number, and the date of purchase for easy contact in the future. We appreciate your confidence in SOLE and we will always remember that you are the reason that we are in business. Please complete and mail

your registration card today and enjoy your new fitness bike.

Yours in Health,

SOLE Fitness

Name of Dealer

Telephone Number of Dealer

Purchase Date

PRODUCT ST

RECORD YOUR SERIAL NUMBER Please record the Serial Number of this fitness product

in the space provided below.

Serial Number

The self-addressed product registration card must be completed in full and returned to SOLE. You can also go to wwwosoletreadmills.com under the support tab to register online.

B94_R92_20110101

B94 / R92 FITNESS BIKE

IMPORTANT TYI ST LICTI

WARNING - Read all instructions before using this appliance.

II Do not operate fitness bike on deeply padded, plush or shag carpet. Damage to both carpet

and fitness bike may result.

II Keep children away from the fitness bike.There are obvious pinch points and other caution

areas that can cause harm.

II Keep hands away from all moving parts. II Never operate the fitness bike if it has a damaged cord or plug. If the fitness bike is not work-

ing properly, call your dealer.

II Keep the cord away from heated surfaces. II Never drop or insert any object into any openings.

II Do not use outdoors. II To disconnect, turn all controls to the off position, remove tether cord, then remove the plug

from the outlet.

II Do not attempt to use your fitness bike for any purpose other than for the purpose it is

intended.

II The hand pulse sensors are not medical devices.Various factors, including the user's move-

ment, may affect the accuracy of heart rate readings.The pulse sensors are intended only as exercise aids in determining heart rate trends in general.

II Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on

your fitness bike. Quality athletic shoes are recommended to avoid leg fatigue or injury.

SAVE THESE INSTRUCTIONS =THINK SAFETY!

B94/R92 FITNESS BIKE 2

IMPORTANTELECTCALl T TI

WARNING/

NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%) or more, the performance of your fitness bike may be

affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing.

NEVER expose this fitness bike to rain or moisture.This product is NOT designed for use out- doors, near a pool or spa, or in any other high humidity environment.The operating tempera- ture specification is 40 to 120 degrees Fahrenheit, and humidity is 95% non-condensing

(no water drops forming on surfaces).

IMPORTANT T I ST CT

II NEVER operate this fitness bike without reading and completely understanding the results

of any operational change you request from the computer.

II NEVER use your fitness bike during an electrical storm. Surges may occur in your household

power supply that could damage fitness bike components. Unplug the fitness bike during

an electrical storm as a precaution.

II Do not use excessive pressure on console control keys.They are precision set to function

properly with little finger pressure. Pushing harder is not going to make the unit go faster

or slower. If you feel the buttons are not functioning properly with normal pressure contact your SOLE dealer.

3 B94/Rg2 FITNESS BIKE

ASSEMLYPACKCHECKLIST

E J)W £. EPJ

#50.3/8"x 2"

Hex Head Bolt (4 pcs)

#51.5/16"x 5/8"

Hex Head Bolt (7 pcs)

#71.3/8"x 25mm x 2T

Flat Washer (4 pcs)

#72.5/16"x 18mm x 1.5T

Flat Washer (6 pcs)

#99.5/16"x 19x 1.5T Curved Washer (1 pc)

#51.5/16" x 5/8"

Hex Head Bolt (2 pcs)

#58. M5 x 12mm

Phillips Head Screw (8 pcs)

B94/Rg2 FITNESS BIKE 4

#72.5/16"x 18mm x 1.5T

Flat Washer (2 pcs)

#103.5/16"x 1.5T

Split Washer (2 pcs)

#93.PhillipsHeadScrewdriver

#100.12/14mmWrench

#92.13/15mm Wrench

ASSEMLYINSTRUCTIONS

PRE-AS

1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack.

2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately.

3. Locate the hardware package. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing

for reference.

5 B94/R92 FITNESS BIKE

1. Attach the Rear Stabilizer (5) onto the Main Frame (1) with the four Hex Head Bolts (50) and four Flat Washers (71).Tighten using the 12/14mm Wrench

(100).

#50.3/8"x 2" Hex Head Bolt (4 pcs) #71.3/8"x 25 x 2T

FlatWasher (4 pcs)

1. Unravel the Computer Cable (29) and pull the twist tie wire through the Console Mast Cover (38) (see illustration for the correct orientation of the

cover)and the Console Mast (2) until the cable connector comes out the top opening of the console mast

2. Attach the Console Mast (2) onto the Main Frame (1) with the seven Hex Head bolts (51). Place six Flat Washers (72) on the side bolts and one Curved

Washer (99) on the front bolt. Tighten using the 12/14mm Wrench (100).

#51.5/16"x 5/8" Hex Head Bolt (7 pcs) #72.5/16"x 18x 1.5T FlatWasher (6 pcs)

#99.5/16"x 19 x 1.ST Curved Washer (1 pcs)

B94/R92 FITNESS BIKE 6

HANDLEBA

i 2

'tJ

1. Remove the plastic tie from the center of the handlebar (3). Insert the two hand pulse cables (26) through the opening of the handlebar mounting bracket on the front side of the console mast tube (2). Pull the cables through the opening of the console mounting bracket at the rear of the console mast

tube

2. Attach the Handle Bar (3) to the Front Console Mast (2) with the two Hex Head bolts (51), two Flat Washers (72) and two Split Washers (103).Tighten using the 12/14mm Wrench (100). Be careful not to pinch the cables when fastening.

| i

#51.5/16"x 5/8" Hex Head Bolt (2 pcs)

#72.5/16"x 18x 1.5T FlatWasher (2 pcs) #103.5/16"x 1.5T Split Washer (2 pcs)

PLASTIC

Seepage 8 for illustration

1. Insert the Computer Cable (29) and two Hand pulse cables (26) into the connectors in the back of the Console (34).

2. Attach the Console (34) onto the Console Mast (2) with four Phillips Head Screws (58). Be careful not to pinch the cables when fastening.

3. Attach the Front Stabilizer Cover (40) and the Rear Stabilizer Cover (41) to the Main Frame (1) with four Phillips Head Screws (58).Tighten with the Phillips

Head Screw Driver (93).

4. Install the Pedals (45 L,46 R)onto the Cranks by using the 13/15mm Wrench (92). Remember that the left pedal has a reverse thread and will be screwed into the crank in the opposite rotation from normal threads. There is an L stamped into the end of the threaded post of the left pedal and an R on the end of the right post. Make sure to tighten the pedals as much asyou possibly can. It may be necessary to re-tighten the pedals if you feel a thumping while pedaling the bike. A clicking noise or thumping feeling is usually caused by loose pedals.

5. Install the Seat mount slide (7) onto the track on top of the seat tube with the seat post facing forward. Place the nut plate (8) onto the seat slide behind the seat post. Place the fiat washer (71) onto the fore/aft adjustment knob (86) and thread it into the nut plate from underneath the seat tube track. Attach the seat (19) to the seat post using the 12/14mm Wrench (100).

/ i

#58. M5 x 12mm Phillips

Head Screw(8 pcs)

7 B94/R92 FITNESS BIKE

+ 21 hidden pages