SolaX Power X1 Series User Manual

Copy Declaration

The c opyri ght of th is manu al belo ngs to So laX Powe r Co.,Lt d.. Any c orpor ation o r indiv idual sho uld not p lagia rize, p artit ially o r fully c opy(i nclud ing sof tware ,etc. ), and no re produ ction o r dis tribu tion of i t in any fo rm or by any m eans. A ll righ ts rese rved. S olaX Po wer Co., Ltd,. reser ves the r ight of f inal in terpr etati on.

614 .0012 7.02

Solax Power Co,. Ltd.

No.288 S hizhu Road, Tonglu Economic Developmen t Zon e, Tonglu Ci ty, Zhej ian g Province, Chin a.

Tel: +86 0571-562 60011 E-m ail: in fo@ solaxpower.com

X1 Series

User Manual

3.0kw - 5.0kw

Contents

1 Note on this M anual

1.1 S cope of Va lidit y

1.2 Tar get G rou p

1.3 S ymbol s Used

2 Safety

2.1 A pprop ria te Usag e

2.2 I mpor tant Sa fety In struc tions

2.3 E xplan ation o f Symbo ls

2.4 EC Di recti ves

3 Introduc tion

3.1 B asic Features

3.2 Ter minal s of Inve rter

3.3 D imens ion

4 Technica l Data

4.1 DC Input

4.2 AC Ou tpu t

4.3 E fficiency, Sa fety an d Protec tion

4.4 G enera l Data

5 Insta llation

5.1 C heck fo r Transport Da mag e

5.2 Pack ing Lis t

5.3 I nstallatio n Prec autio n

5.4 I nstallatio n Steps

5.5 C onnec tion of the I nverte r

5.6 R un the Inverte r

6 Operatio n Method

6.1 C ontro l Panel

6.2 LCD Fu nct ion

6.3 LCD O per ati on

The copy right of this m anual bel ongs to SolaX Pow er Co.,Ltd..Any cor poration or indiv idual sho uld not plagia rize,pa rtially cop y or fully co py it(includ ing software ,etc.), and no rep roduction or d istributi on of it in any fo rm or by any means. All rights res erved. SolaX Power Co.,Lt d,.reserves the righ t of final inter pretation. This informa tion is sub ject to chang es without not ice.

Copyr ig ht Decl aration

Con tents

1.1 Scope of Validit y

This manual is an integral part of X1 Series, It describes the assembly, installation, commissioning, maintenance and failure of the product. Please read it carefully before operating.

X1-3.0-T-D X1-3.3-T-D X1-3.6-T-D X1-4.2-T-D X1-4.6-T-D(AU) X1-5.0-T-D X1-5.0-T-D(AU) X1-3.0-T-N X1-3.3-T-N X1.3.6-T-N X1-4.2-T-N X1-4.6-T-N(AU) X1-5.0-T-N X1-5.0-T-N(AU)

Note: “3.0” means 3.0kW. ”T” means “double” MPPT strings. “D” means with “DC Switch”, ”N” means without “DC Switch”. X1-4.6-T-D(AU)/X1-4.6-T-N(AU)/ X1-5.0-T-D(AU)/X1-5.0-T-N(AU) are only for Australia. Store this manual where it will be accessible at all times.

1.2 Target Gr oup

This manual is for qualified electricians. The tasks described in this manual only can be performed by qualified electricians.

1.3 Symbols Used

The following types of safety instructions and general information appear in this document as described below:

Danger！

“Danger” indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Warning！

“Warning” indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

Caution！

“Caution” indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

Note！

“Note” provides tips that are valuable for the optimal

1 Notes on this Manual

7 Troublesho oting

7.1 Trouble Sh oot ing

7.2 R outin e Maintenance

8 Decommis sioning

8.1 D isman tling t he Inve rter

8.2 Pack aging

8.3 S torag e and Transpo rta tion

Not es on thi s Manua lCon tents

2 Safety

2.1 Appropriate Usage

The X1 Series are PV inverters which can convert the DC current of the PV generator into AC current and feed it into the public grid.

Surge protection devices (SPDs) for PV installation

Over-voltage protection with surge arresters should be provided when the PV power system is installed. The gr id connec ted inv erter is not fitte d with S PDs in both PV input side and MAINS side.

WARNIN G!

Induced surges are the most likely cause of lightning damage in majority or installations, especially in rural areas where electricity is usually provided by long overhead lines. Surge may be included on both the PV array conduction and the AC cables leading to the building.

Specialists in lightning protection should be consulted during the end use application. Using appropriate external lightning protection, the effect of a direct lightning strike into a building can be mitigated in a controlled way, and the ligh tning current can be discharged into the ground.

Installation of SP Ds to protect the inverter against mechanical damage and excessive st ress include a surge ar rester in case of a building with external lightning protection system (LPS) when separation distance is kept.

To protect the DC system, surge suppression device (SPD type2) should be fitted at the inverter end of the DC cabling and at the arr ay located be tween the inverter and the PV generator, if the voltage protection level (VP) of the surge arresters is greater than 1100V, an additional SPD type 3 required for surge protection for electrical devices.

To protect the AC system, surge suppression devices (SPD t ype2) should be fitted at the main inco ming poin t of A C supply (at the co nsumer’s c utout), located between the inverter and the meter/distr ibution system; SPD (test impulse D1) for signal line according to EN 61632-1.

All DC cables should be installed to provide as short a run as possible, and positive and negative cables of the string or main DC supply should be bundled together. Avoid ing the creation of loops in the system. This requirement for short runs and bundling includes any associated earth bundling conductors.

Spark gap devices are not suitable to be used in DC circuits once conducti ng, they won’t stop conducting until the voltage across their terminals is typically more than 30 volts.

Lightning will cause a damage either from a direct strike or from surges due to a nearby strike.

►

Safe ty

DC di stri butio n box

AC di stri butio n box

Ele ctric al gri d

Ele ctric m eter, bid irect ional

Sol aX Mete r

Loa d

PV a rray

Surg e arres tor Fuse DC br eaker

Surg e arres tor Fuse AC br eaker

Safe ty

Anti-Islanding Effect

►

Islanding eﬀect is a special phenomenon that grid-connected PV system still supply power to the nearby grid when the voltage loss is happened in the power system. It is dangerous for maintenance personnel and the public. X1 series provide Active Frequency Drift(AFD) to prevent islanding eﬀect.

2.2 Imp or tant Safety Instructions

Dan ger! Danger to life due to high voltages in the inverter!

All work must be carried out by qualified electrician. The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance.

Cau tion! Danger of burn injuries due to hot enclosure parts!

During operation, the upper lid of the enclosure and the enclosure body may become hot. Only touch the lower enclosure lid during operation.

Cau tion! Possible damage to health as a result of the effects of radiation!

Do not stay closer than 20 cm to inverter for any length of time.

Not e! Grounding the PV generator.

Comply with the local requirements for grounding the PV modules and the PV generator. SolaX recommends connecting the generator frame and other electrically conductive surfaces in a manner which ensures continuous conduction and ground these in order to have optimal protection of system and persons.

Warni ng!

Ensu re input DC voltage ≤Max. DC vol tage .Over voltage may cause permanent damage to inverter or ot her losses , whic h will not be inc luded in warr anty !

Warning！

Authorized service personnel must disconnect both AC and DC power from X1 series before attempting any maintenance or cleaning or working on any circuits connected to the X1 series.

Prior to the application, please read this section carefully to ensure correct and safe application. Please keep the user manual properly. Use only attachments recommended or sold by SolaX. Otherwise may result in a risk of fire, electric shock, or injury to person. Make sure that existing wiring is in good condition and that wire is not undersized. Do not disassemble any parts of inverter which are not mentioned in installation guide. It contains no user-serviceable parts. See Warranty for instructions on obtaining service. Attempting to service the X1 Series inverter yourself may result in a risk of electric shock or fire and will void your warranty. Keep away from flammable, explosive materials to avoid fire disaster. The installation place should be away from humid or corrosive substance. Authorized service personnel must use insulated tools when installing or working with this equipment. PV modules shall have an IEC 61730 class A rating.

Never touch either the positive or negative pole of PV connecting device.

Strictly prohibit touching both of them at the same time.

The unit contains capacitors that remain charged to a potentially lethal voltage after the MAINS and P V supply has been disconnected. Hazardous voltage will present for up to 5 minutes after disconnection from power supply. CAUTION-RISK of electric shock from energy stored in capacitor,. Never operate on the solar inverter couplers, The MAINS cables, PV cables or the P V generator when power is applied. After switching off the PV and Mains, always wait for 5minutes to let the intermediate circuit capacitors discharge before you unplug DC and MAINS couplers. When accessing the internal circuit of solar inverter, it is very important to wait 45minutes before operating the power circuit or demounting the electrolyte capacitors inside the device. Do not open the device before hand since the capacitors time to sufficiently discharge! require Measure the voltage between terminals UDC+ and UDC- with a multi-meter (impedance at least 1Mohm) to ensure that the device is discharged before beginning work (35VDC) inside the device.

Safe ty Safe ty

0706

Do not operate the inverter when the device is running.

WARNIN G!

Risk of electric shock!

WARNIN G!

PE Connection and Leakage Current

• The end-use application shall monitor the protective conductor by residual current operated protective device (RCD) with rated fault current Ifn≤240mA which automatically disconnects the device in case of a fault.

• DC differential currents are created (caused by insulation resistance and through capacities of the PV generator). In order to prevent unwanted triggering during operation, the rated residual current of the RCD has to be min 240mA.

The device is intended to connect to a PV generator with a capacitance limit of approx 700nf.

High leakage current! Earth connection essential before connecting supply.

WARNIN G!

• Incorrect grounding can cause physical injury, death or equipment malfunction and increase electromagnetic.

• Make sure that grounding conductor is adequately sized as required by safety regulations.

• Do not connect the ground terminals of the unit in series in case of a multiple installation. This product can cause current with a d.c component, Where a residual current operated protective (RCD) or monitoring (RCM) device is used for protection in case of direct or indirect contact, only an RCD or R CM of type B is allowed on the supply side of this product. For United Kingdom

• The installation that connects the equipment to the supply terminals shall comply with the requirements of BS 7671.

• Electrical installation of PV system shall comply with requirements of BS 7671 and IEC 60364-7-712.

• No protection settings can be altered.

• User shall ensure that equipment is so installed, designed and operated to maintain at all times compliance with the requirements of ESQCR22(1)(a). For Australia and New Zealand

• Electrical installation and maintenance shall be conducted by licensed electrician and shall comply with Australia National Wiring Rules.

0908

2.3 Explanation of Symbols

This section gives an explanation of all the symbols shown on the inverter and on the type label.

Symbols on the Inverter

Symbol Explanation

Operating Display.

Communication is active.

An error has occurred, please inform your installer immediately.

Symbols on the Type Label

Symbol Explanation

CE mark. The inverter complies with the requirements of the applicable CE guildlines.

RCM remark.

SAA certification.

Beware of hot surface. The inverter can become hot during operation. Avoid contact during operation.

Danger of high voltages. Danger to life due to high voltages in the inverter!

Danger. Risk of electric shock!

Observe enclosed documentation.

The inverter can not be disposed together with the household waste. Disposal information can be found in the enclosed documentation.

Do not operate this inverter until it is isolated from mains and on-site PV generation suppliers.

Danger to life due to high voltage. There is residual voltage in the inverter which needs 5 min to discharge.

• Wait 5 min before you open the upper lid or the DC lid.

Safe ty Sa fety

2.4 CE D irecti ves

This chapter follows the requirements of the European low voltage directives, which contains the safety instructions and conditions of acceptability for the endues system, which you must follow when installing, operating and servicing the unit. If ignored, physical injury or death may follow, or damage may occur to the unit. Read this instructions before you work on the unit. If you are unable to understand the dangers, warnings, cautions or instructions, please contact an authorized service dealer before installing. Operating and servicing the unit. The Grid connected inverter meets the requirement stipulated in Low Voltage Directive (LVD) 2014/35/EU and Electromagnetic Compatibility (EMC) Directive 2014/30/EU. The unit is based on: EN 62109-1:2010 ; EN 62109-2:2011 ; IE C 62109-1(ed.1) ; IEC62109-2(ed.1) EN 61000-6-3:2007+A:2011 ; EN 61000-6-1:2007 ; EN 61000-6-2:2005 In case of installation in PV system, startup of the unit (i.e. start of designated operation) is prohibited until it is determined that the full system meets the requirements stipulated in EC Directive (2014/35/EU,2014/30/EU, etc.) The grid connected inverter leave the factory completely connecting device and ready for connection to the mains and PV supply ,the unit shall be installed in accordance with national wiring regulations. Compliance with safety regulations depends upon installing and configuring system correctly, including using the specified wires. The system must be installed only by professional assemblers who are familiar with requirements for safety and EMC. The assembler is responsible for ensuring that the end system complies with all the relevant laws in the country where it is to be used. The individual subassembly of the system shall be interconnected by means of the wiring methods outlined in national/international such as the national electric code (NFPA) No.70 or VDE regulation 0107.

3. Introduction

3.1 Basic features

Congratulations on your purchase of a X1 Series inverter from SolaX. The X1 Series inverter is one of the finest inverters on the market today, incorporating state-of-the-art technology, high reliability, and convenient control features.

Advanced DSP control technology. Utilize the latest high-efficiency power component. Optimal MPPT technology.

- Two independent MPP Tracking.

- Wide MPPT input range. Advanced anti-islanding solutions. IP65 protection level. Max. efficiency up to 97.8%.EU efficiency up to 97%. THD<2%. Safety &Reliability: transformerless design with software and hardware protection. Export control. Power factor regulation. Friendly HMI.

- LED status indications.

- LCD display technical data, Human-machine interaction through press key.

- Dry contact communication interface.

- PC remote control.

- Upgrade through USB interface.

- Pocket Wi-Fi monitoring.

- Control loads’ switch intelligently by RF.

- Energy conservation.

3.2 Terminals of inverter

E F

I J

A B C G HD

10 11

Safe ty Int roduc tion

Warning!

Only authorized personnel is allowed to set the connection.

3.3 Dimension

Dimension

339mm

420mm

143mm

4. Technical Data

4.1 DC input

Max. recommended DC power [W]

Max. DC voltage[V]

Norminal DC operating voltage[V]

MPPT voltage range [V]

MPPT voltage range@full load [V]

Max. input current [A]

Max. short circuit current [A]

Start input voltage [V]

Start output voltage [V]

No. of MPP trackers

Strings per MPP tracker

DC disconnection swtich

3250

600

360

125-580

150-550

12/12

15/15

110

150

X1-3.0-T-N X1-3.3-T-N

X1-3.6-T-N

X1-4.2-T-N

X1-4.6-T-N(AU)

3500

600

360

125-580

150-550

12/12

15/15

110

150

4000

600

360

125-580

160-550

12/12

15/15

110

150

optional

4600

600

360

125-580

190-550

12/12

15/15

110

150

5200

600

360

125-580

220-550

12/12

15/15

110

150

4.2 AC output

Rated output power [W]

Max.apparent AC power [VA]

Rated grid voltage and range [V]

Rated AC frequency and range [Hz]

AC norminal current [A]

Max. output fault current [A]

Inrush current(A)

THD

Displacement power factor

Feed in phase

Over voltage category

3000

3300

14.3

3680

4200

4600

220/230/240 (180-280)

50(45-55)/60(55-65)

Object

A DC Switch (optional)

Waterproof Lock Valve DC Connector

Pocket WiFi (optional)

DRM

Smart plug (optional)

AC Connector

B C D E F G H

I J

Description

E. F. Alarm(optional)

RS 485/ Meter(optional) USB for Upgrade

Ground screw

12 13

Int roduc tion Techn ical Da ta

X1-3.0-T-D/

X1-3.3-T-D/

X1-3.6-T-D/

X1-4.2-T-D/

X1-4.6-T-D(AU)/

Model

X1-5.0-T-N(AU)

5200

600

360

125-580

220-550

12/12

15/15

110

150

X1-5.0-T-D(AU)/

4999

<2%

0.8 leading-0.8lagging

single-phase

III (electric supply side), II (P V side)

Max. output overcurrent protection(A)

Max. inverter backfeed current to the array(mA)

X1-5.0-T-N

5200

600

360

125-580

220-550

12/12

15/15

110

150

X1-5.0-T-D/

Note: The models(X1-4.6-T-D(AU)/X1-4.6-T-N(AU)/X1-5.0-T-D(AU)/X1-5.0-T-N(AU)) with signal “*” are only for Australia.

X1-3.0-T-N X1-3.3-T-N

X1-3.6-T-N

X1-4.2-T-N

X1-4.6-T-N(AU)

X1-3.0-T-D/

X1-3.3-T-D/

X1-3.6-T-D/

X1-4.2-T-D/

X1-4.6-T-D(AU)/

X1-5.0-T-N(AU)

X1-5.0-T-D(AU)/

X1-5.0-T-N

X1-5.0-T-D/

4600

4.3 Efficiency, Safety and Protection

MPPT eﬃciency

Euro eﬃciency

Max. eﬃciency

Safety & Protection

Over/under voltage protection

DC isolation protection

Monitoring ground fault protection

Grid protection

DC injection monitoring

Back feed current monitoring

Residual current detection

Anti-islanding protection

Over load protection

Over heat protection

Inverter+BMU

99.90%

97.00%

97.80%

4.4 General Data

Dimension [W/H/D](mm)

Dimension of packing [W/H/D](mm)

Net weight [kg]

Gross weight [kg]

Installation

Operating temperature range[℃]

Storage temperature [℃]

Storage/Operation relative humidity

Altitude [m]

Ingress Protection

Isolation type

Protective Class

Night-time consumption

Over Voltage Category

Pollution Degree

cooling

Noise level

Inverter Topology

Communication interface

Standard warranty [year]

Inverter+BMU

99.90%

97.00%

97.80%

99.90%

97.00%

97.80%

99.90%

97.00%

97.80%

99.90%

97.00%

97.80%

YES

420*339*143

583*492*278

Wall-mounted

-20~+60 (derating at 45)

-20~+60

0%~95%, no condensation

<2000

IP65(for outdoor use)

Transformerless

Ⅰ

<3w

Ⅲ(MAINS),Ⅱ(PV)

Ⅱ

Forced airow

＜25dB

non-isolated

RS485/ WIFI /Meter(optional)/ USB / DRM

5 (optional)

5. Installation

5.1 Check for Transport Damage

5.2 Packing List

Make sure the inverter is intact during transportation. If there are some visible damages, such as cracks, please contact your dealer immediately.

Open the package and fetch out the product, check the accessories at first. The packing list shows as below.

Object

X1 series inverter1A

A B

E F

B C D E F G H

J K

1 4 1 3 3

1 1

Bracket DC connector AC connector Expansion tube Expansion screw

Earth terminal

Product manual Warranty card

Quick installation guide

Quantity

Description

Techn ical Da ta Ins talla tion

Model

Meter( Optional )

Smart Plug( Optional )

X1 Series 3.0KW-4.6KW

Pocket WiFi( Optional )

14.6 14.6 16.7 16.7

17.6

19.7

99.90%

97.00%

97.80%

16.7

19.7

14.6

17.6

DC pin contact(2*positive, 2*negative)

Waterproof connector with RJ45

X1-3.0-T-N X1-3.3-T-N

X1-3.6-T-N

X1-4.2-T-N

X1-4.6-T-N(AU)

X1-3.0-T-D/

X1-3.3-T-D/

X1-3.6-T-D/

X1-4.2-T-D/

X1-4.6-T-D(AU)/

X1-5.0-T-N(AU)

X1-5.0-T-D(AU)/

X1-5.0-T-N

X1-5.0-T-D/

99.90%

97.00%

97.80%

X1-3.0-T-N X1-3.3-T-N

X1-3.6-T-N

X1-4.2-T-N

X1-4.6-T-N(AU)

X1-3.0-T-D/

X1-3.3-T-D/

X1-3.6-T-D/

X1-4.2-T-D/

X1-4.6-T-D(AU)/

X1-5.0-T-N(AU)

X1-5.0-T-D(AU)/

X1-5.0-T-N

X1-5.0-T-D/

16.7

19.7

5.3 Installation Precaution

Please avoide direct sunlight, rain exposure, snow laying up during installing and operating.

Available Space Size

X1 Series inverter is designed for outdoor installation (IP 65). Make sure the installation site meets the following conditions: Not in direct sunlight. Not in areas where highly flammable materials are stored. Not in potential explosive areas. Not in the cool air directly. Not near the television antenna or antenna cable. Not higher than altitude of about 2000m above sea level. Not in environment of precipitation or humidity (＞95%). Be sure the ventilation is good enough. The ambient temperature in the range of -20℃ to +60℃. The slope of the wall should be within ±5°.

Position Min.size

30cm 30cm

Left

30cm 30cm 30cm 30cm 30cm

Right Top Bottom Front

Table Available Space Size

30cm

5.4 Installation Steps

Preparation

Step 1: Screw the wall bracket on the wall

Step 2: Match the inverter with wall bracket

Below tools are needed before installation.

Installation tools : crimping pliers for binding post and RJ 45, screwdriver, manual wrench and

a) Use the wall bracket as a template to mark the position of the 3 holes on the wall. b) Drill holes with driller, make sure the holes are deep enough (at least 50mm) for installation, and then tighten the expansion tubes.

c) Install the expansion tubes in the holes, and tighten them. Then

install the wall bracket by using the expansion screws.

d) Hang the inverter over the bracket, move the inverter close to it, slightly lay down the inverter, and make sure the 3 mounting bars on the back are fixed well with the 3 grooves on the bracket.

16 17

Ins talla tion Ins talla tion

The wall hanging the inverter should meet conditions below:

1.solid brick/concrete, or strength equivalent mounting surface;

2.Inverter must be supported or strengthened if the wall’s strength isn’t enough(such as wooden wall, the wall covered by thick layer of decoration)

5.5 Connection of the Inverter

PV String Connection

X1series inverter have a couple of PV connectors which can be connected in series into 2-strings PV modules. Please select PV modules with excellent function and reliable quality. Open circuit voltage of module array connected should be ＜ Max.DC (table as follow) input voltage, and operating voltage should be within the MPPT voltage range.

c) d)

Table 3 Max. DC Voltage Limitation

Max.DC Voltage

600V

Warning!

PV module voltage is very high which belongs to dangerous voltage range, please comply with the electric safety rules when connecting.

Warning!

Plea se do not mak e PV po sitive or negative grou nd!

Note!

Please follow the requirements of PV modules as below: Same type; Same quantity; Identical alignment; Identical tilt. In order to save cable and reduce the DC loss, we suggest installing the inverter near PV modules.

5.5.1 The Main Steps to Connect to the Inverter

Inverter+BMU

Connection Steps

a) Turn off the DC switch. b) Choose 12 AWG wire to connect the PV module. c) Trip 6mm of insulation from the wire end. d) Separate the DC connector as below.

d) Separate the DC connector as below.

e) Insert striped cable into pin contact and ensure all conductor strand are captured in the pin contact. f ) Crimp pin contact by using a crimping pliers. Put the pin contact with striped cable into the corresponding crimping pliers and crimp the contact.

g) Insert pin contact through the cable nut to assemble into back of the male or female plug. When you feel or heard a “click” the pin contact assembly is seated correctly.

6.0 mm

12AWG

trip length

plug

pin contact

cable nut

18 19

Ins talla tion Ins talla tion

Model

Note!

Please choose a tting external DC switch if the model (X1-3.0-TN,X1-3.3-T-N,X1-3.6-T-N,X1-4.2-T-N,X1-4.6-T-N,X1-5.0-T-N) is purchased.

Note!

PV connection mode below is not allowed!

Inv erter

PV a rray

PV 1

PV 2

X1-3.0-T-N X1-3.3-T-N

X1-3.6-T-N

X1-4.2-T-N

X1-4.6-T-N(AU)

X1-3.0-T-D/

X1-3.3-T-D/

X1-3.6-T-D/

X1-4.2-T-D/

X1-4.6-T-D(AU)/

X1-5.0-T-N(AU)

X1-5.0-T-D(AU)/

X1-5.0-T-N

X1-5.0-T-D/

Connection Steps

Grid Connection

X1 series inverter are designed for single phase grid. Voltage range is 220/230/240V, frequency is 50/60Hz. Other technical requests should comply with the requirement of the local public grid.

Micro-breaker should be installed between inverter and grid, any loads should not be connected with inverter directly.

a) Check the grid voltage and compare with the permissive voltage range (refer to technical data). b) Disconnect the circuit-bricker from all the phases and secure against reconnection. c) Trip the wires:

- Trip all the wires to 52.5mm and the PE wire to 55mm.

- Use the crimping pliers to trip 12mm of insulation from al wire ends as below.

Table 4 Cable and Micro-breaker recommended

Incorrect Connection between Load and Inverter

Cable

4-5mm²

Inverter+BMU

Micro-breaker

4-5mm² 4-5mm² 5mm² 5mm²

20A 20A 20A 25A 25A

d) Separate the AC plug into three parts as below.

- Hold the middle part of the female insert, rotate the back shell to loose it, and datach it from female inset.

- Remove the cable nut (with rubber insert) from the back shell.

e) Slide the cable nut and then back shell onto the cable.

f ) Insert the tripped end of each three wires into the appropriate hole in the female insert, and then tight each screw (to tight each wire in place).

g) Screw down the threaded sleeve the pressure screw.

h) Screw down the pressure screw.

I) Connect the AC plug to the inverter.

Ins talla tion Ins talla tion

Model

5mm²

25A

5mm²

25A

*The parameters have some differences because of different surrounding and material. Please according to the local conditions to choose appropriate cable and micro-breaker.

X1-3.0-T-N X1-3.3-T-N

X1-3.6-T-N

X1-4.2-T-N

X1-4.6-T-N(AU)

X1-3.0-T-D/

X1-3.3-T-D/

X1-3.6-T-D/

X1-4.2-T-D/

X1-4.6-T-D(AU)/

X1-5.0-T-N(AU)

X1-5.0-T-D(AU)/

X1-5.0-T-N

X1-5.0-T-D/

5mm²

25A

5mm²

25A

Main cable(AC line cable)shall be short circuit protected and thermal overload protected. Always fit the input cable with fuse. Normal gG(US:CC or T )fuses will protect the input cable in short circuit situation. They will also prevent damage to adjoining equipment. Dimension the fuses according to local safety regulations, appropriate input voltage and the related current of the solar inverter.

AC output protected by external fuse(gG rated current 25A/250VAC for 3.0KW /3.3KW; 32A/250VAC for 3.6KW/4.2KW/4.6KW )provides in all live connections to the AC supply.

The rated short circuit breaking capacity of the above protective device shall be at least equal to the prospective fault current at the point of installation. See section technical data of this manual details.

2 2

AC output cable: Cu; L, N+PE: 2*4.0mm +4.0mm for 3.0KW/3.3KW/3.6K W and

2 2

2*5mm +5mm for 4.2KW/4.6KW @40℃ ambient temperature with a max length of 5m, with operating time of the fuses is less than 5 seconds, installation method B2 according to EN60204-1:2006, annex D: cable in conduit cable trunking system, number of loaded circuit only one. Use H07RNF(cord designation 60245 IEC66) for an ambient temperature of 40℃ or less and use 90℃ wire for ambient temperature between 40℃ and 60℃.

Note 1: For condition differing form those mentioned above, dimension the cables according to local safety regulations, appropriate input voltage and the load and the load current of the unit.(You can choose a thicker cable but the fuses must rated according to the cable.)

Note 2: Fuses must be approved by Notified Body.

Inverter is not provided galvanic isolation from the mains to the PV array, feedback current to the array is 25A/250VAC for 3.0KW and 3.3KW; 32A/250VAC for 3.6KW, 4.2KW and 4.6K W based on the fuse provided in the mains. Also in the worst case the reverse current comprises the sum of the short-circuit currents of all intact lines.

Therefore the current-carrying capacity of the components and sub-assemblies provided in the end-use system(connectors, cables, junction box, switch ger, etc.) and the reverse current PV modules shall be considered based on the feedback current and reverse current. The direct current(DC) circuit breaker or fuse between each solar generator and inverter shall be provided based on solar inverter input ratings. Select DC cables based in the above inverter back-feed current and ISC P V rating and Vmax ratings.

Selection of Fuses and Cables

Note!

Earth Connection

Screw the ground screw with allen wrench shown as follow.

5.5.2 Communication interface

This product has a series of communication interfaces: such as WIFI, R F, RS485/Meter, DRM and USB for upgrading for human and machine communication. Operating information like output voltage, current, frequency, faulty information, etc., can be delivered to PC or other monitoring equipment via these interfaces.

WiFi

This inverter provides a WiFi port which can collect information from inverter including status, performance and updating information to monitoring website via connecting Pocket WiFi( purchase the product from supplier if needed)

Connection steps:

1.Plug the Pocket WiFi into “WiFi” port at the bottom of inverter.

2.Connect the wifi with router.

3.Set the station account on the solaX web.(Please check the Pocket WiFi user manual for more details)

22 23

Ins talla tion Ins talla tion

RS 485/Meter

RS 485 is one standard communication inter face which can transmit the real

data from inverter to P C or other monitoring equipments.

a. RS 485

RF(Optional)

The inverter provides a RF(radio frequency) interface which can make a load be switched or operated in a specied duration via connecting an external Smart plug(purchase the product from supplier if needed.) so that the load mostly consumes PV energy and incurs the lowest-possible energy costs during operation. Please check the Smart Plug user manual for the detail of connection steps.

b. Meter(optional)

Monitor the energy to grid and from grid throughout the whole day. Ach iev e the exp ort control funct ion w ith a h igh er ac curac y.

Please see the Quick Guide for Single Phase Meter Installation for details.

The PIN denitions of RS 485/Meter interface are as below.



Definition

1 2 3 4 5 6 7 8

485_A

METER 485_A

485_B

METER 485_B

XX X X

RS 485 Connection Steps:

Meter Connection Steps:

Electrical

grid

Electric meter,

bidirectional

Single phase

meter

Load

X1 series inverter

1. Prepare RJ 45 conn ector and a communication cabl e.

2. Trip the insulation from the communication cable.

3. Let the communication cable pass though the waterproof connector with RJ45, then insert it into the RJ45 connector following the PI N definition rule.

4. Crimp the RJ45 connector with the crimping plier.

5. Insert the cable into the RS 485/Meter port of the inverter, and tighten the waterproof connector.

DRM is provided to support several demand response modes by giving control signals as below.



Definition

3 4

DRM1/5 DRM2/6 DR M3/7 DR M4/8

RefGen

Com/DRM0

V+

V-

DRM

Connection Steps:

Ins talla tion Ins talla tion

With this single phase meter working together with the X1 series, you can:

1.Prepare R J45 con nector and a communication cab le.

2.Trip the insulation from the communication cable.

3.Let the communication cable pass though the waterproof plug, then insert it into the RJ45 connector following the PIN definition rule.

4. Crimp the RJ45 connector with the crimping plier.

5.Insert the cable into the DRM port of the inverter, and tighten the waterproof plug.

Upgrade

User can update the inverter system through an U-disk.

2) Make sure the DC switch is off and the AC is disconnected with grid. Unscrew the waterproof lid of Upgrade port by straight screwdriver as below.

1) Please contact our service support to get the update file, and extract it into your U-disk as the following file path:

Make sure the directory is in accordance with above form strictly! Do not modify the program file name ! Or it may cause the inverter not work anymore !

Make sure the input voltage is more than 150V (in good illumination condition), or it may result in failing during updating.

“update\ \618.00074.00_X1BOOST_ _Vx.xx_xxxxxxxx.usb”;ARM ARM “update\DSP\618.00070.00_X1BOOST_DSP_Vx.xx_xxxxxxxx.hex”.

Upgrade Steps:

Update

AR M DS P

3) then insert U-disk into the USB port on the bottom of the inverter. Then turn on DC switch or connect the PV connector, the LCD will show picture as below.

During updating, please turn off the DC switch or disconnect the PV connector, then reinsert the U-disk if the updating is stopped.

The earth fault alarm is the additional detection, as required by AS

4777.2 and AS/NZS 5033, it will give an alarm once the earth impedance of the PV arrays is less than 30KΩ .

Earth Fault Alarm(Optional)

Ins talla tion Ins talla tion

5) After the upgrade is complete, please remember to turn off the DC switch or disconnect the PV connector, then pull off the U-disk, screw the waterproof lid.

Note: Vx.xx is version number, xxxxxxxx is file completion dates.

5 m

4) Press up and down to select the one that you want to update and press “OK” to confirm to update.

U-disk

Straight screwdriver

Waterproof lid

5.6 Run the inverter

a) Ch eck tha t devic e is xed w ell o n the w all.

b) Make sure all the DC breakers and AC breakers are disconnected. c) AC cable is connected to grid correctly. d) All PV panels are connected to inverter correctly, DC connectors which are not used should be sealed by cover. e) Turn on the external AC and DC connectors. f ) Turn on the DC switch to the “ON”position.

Start inverter after checking all below steps:

Start inverter

Inverter will start automatically when PV panels generate enough energy. Check the status of LED and LCD screen, the LED should be blue and the LCD screen should display the main interface. If the LED is not blue, please check the below:

- All the connections are right.

- All the external disconnect switches are closed.

- The DC switch of the inverter is in the “ON” position.

Warning!

Power to the unit must be turned on only after installation work has been completed. All electrical connections must be carried out by qualied personnel in accordance with legislation in force in the country concerned.

Not e!

Please set the inverter if it is the first time to start up.

Above steps are for the regular start of the inverter. If it is the first time to start up the inverter, you need to setup the inverter.

6. Operation Method

6.1 Control panel

Below is the three diﬀerent states when operating, which means inverter starting up successfully.

Waiting: Inverter is waiting to checking when DC input voltage from panels is greater than 100V(lowest start-up voltage) but less than 150V(lowest operating voltage).

Checking: Inverter will check DC input environment automatically when DC input voltage from the PV panels exceeds 150V and PV panels have enough energy to start inverter. Normal: Inverter begins to operate normally with green light on. Meanwhile feedback energy to grid, LCD displays present output power.

Enter the setting interface to follow the instructions when it is rst time to start up.

Object Name Description

Indicator LED

Function Button

Blue:The inverter is in normal state.

Red:The inverter is faulty.

Yellow:The inverter is in communication.

Down button: Move cursor to downside or decrease value.

ESC button: Return from current interface or function.

OK button: Conrm the selection.

Up button: Move cursor to upside or increase value.

LCD Screen

Display the information of the inverter.

2828 29

Ins talla tion Ope ratio n Metho d

Status

Main menu

Settings

About

Grid

Solar

Machine Tpye

Main DSP1

Power Factor

Manager

Slave DSP2

New Password

History

Reset energy

Export Control

Power Limits

Grid

Load consumption

6.2 LCD Function

Menu structure

Load

(Optional)

P(U) Function

Safety

Date Time

Reset Error logs

Start guide

Language

(Optional)

Inverter Yield

Error Logs

(Optional)

feed in energy

(Optional)

6.3 LCD Operation

● LCD Digital Display

The main interface is the default interface, the inverter will automatically jump to this interface when the system started up successfully or not operated for a period of time. The information of the interface is as below. “Power” means the timely output power; “Pgrid” means the power export to or import from the grid.“Today” means the power generated within the day.“Normal”shows the status of the inverter.

● Menu interface

The menu interface is a transfer interface for user to get into other inter face to finish the setting or getting the information.

-User can get into this interface by pressing “OK” button when LCD displays the main interface.

-User can select interface by moving the cursor with function button，and press “OK” to confirm.

● Status

The status function contains two aspects of the inverter, grid and solar. Press up and down to select and press “OK” to confirm the selection, press “ESC” to return to Menu.

a) Grid This status shows the current grid condition such as voltage, current, output power and the local consumed power. Pout measures the output of the inverter, Pgrid measures power export to or import from grid. Positive value means the energy feeds into grid, negative value means the energy used from the grid. Press up and down button to review the parameter, press “ESC” to return to Status .

Powe r

Pgr id

Today

00. 0KWh

Nor mal

﹦﹦ ﹦ ﹦ Men u ﹦﹦ ﹦ ﹦

Stat us

His tory

Set tings

﹦﹦ ﹦ ﹦ Stat us ﹦﹦ ﹦﹦

Gri d

Sol ar

Loa d

Password

Relay Control

Reset Consume

Reset Feed in

Note: ” ”Can be set by the end user. Others can only be set by the technical or the installer with the installer password.

30 31

Ope ratio n Metho dOpe ratio n Metho d

DRM Function

Password The default password is “0000”for end user, which only allows the user to review the current setting and some easy setting. If professional change is needed, please contact with the distributor or factory for installer password. We need to increase or decrease the word by pressing up or down button. Press OK to confirm an alternate to the next word. After word is confirmed, ,press “OK” to enter password.

●Settings

Setting function is used for setting the inverter for time, connection, Grid and so on. Since this function will change the inverter's parameter, the end user with the user password as”0000” has the limited authority to change the setting. We need installer password to do most of the professional setting.

﹦﹦ ﹦ ﹦Set ting ﹦ ﹦ ﹦ ﹦

Safe ty

Lan guage Dat e Time

﹦﹦ ﹦ ﹦Pas swor d ﹦﹦ ﹦ ﹦

0 0 0 0

﹦﹦ ﹦ ﹦Safe ty ﹦﹦ ﹦ ﹦

cou ntry

VD E410 5

﹦﹦ ﹦ ﹦ Loa d ﹦﹦ ﹦ ﹦

Loa d 1 Power

.0 W

0.0 W

Loa d 2 Power

Setting If inputting the installer password, the information of the LCD interface is as below.

a) Safety The user can set the safety standard here. According to different countries and grid tied standards. There is 10 standards for choice (May change without notice).

b) Solar Thi s stat us shows t he real ti me PV condit ion of the sy stem, suc h as inp ut volta ge, current a nd pow er situat ion of each PV in put. Press up and down button to review parameter, Press “ESC” to return to Status.

﹦﹦ ﹦ ﹦ Sol ar ﹦﹦ ﹦ ﹦

U1 0. 0V

I 1 0.0 A P1 0. 0W

c) Load If the inve rte r is plugged in a s mart plug, th is s tatu s show s th e real time loa d powe r, include l oad1 pow er and load 2 p ower. Pres s up an d down button to revi ew para meter, Press “E SC” to return to Sta tus.

Item

Country

Standard

VDE 4105

IEC 61727

EN50438_NL

Australia

German

AS/N2S 4777.2:2015

Item

Country

Standard

Netherland

India

﹦﹦ ﹦ ﹦ Gri d ﹦﹦ ﹦ ﹦

.0 V

I 0.0 A Pout 0.0 W

32 33

Ope ratio n Metho dOpe ratio n Metho d

c) Date time This interface is for user to set the system date and time. Increase or decrease the word by pressing up or down button. Press OK to confirm and alternate to next word. After all the words are confirmed. Press “OK” to enter the date and time.

﹦﹦ ﹦ ﹦Dat e time ﹦﹦ ﹦﹦

201 6 >06 <06 10 19

d) New Password Installer can set the new password here. We need to increase or decrease the word by pressing up or down button. Press OK to confirm and alternate to next word. After word is confirmed., press “OK” to reset the password.

﹦﹦ ﹦New Passw ord ﹦﹦﹦

1 2 3 4

e) Power Factor ( For specific country if required by the local grid.)

There are 5 modes for selecting: Off , Under-Excited, Over-Excited, Curve, Q( u ). All parameters are shown below.

Mode Comment

Off

Under-Excited PF value

Over-Excited PF value

Curve

Upper limit

Lower limit

Power Upper

Power Lower

Q( u )

QuVupRate

QuVlowRate

( EN50438_NL )

Reactive power control, Reactive standard curve cos φ = f(P)

For VDE ARN 4105, curve cos φ = f(P) should refer to curve A. default values of setting are as shown in curve A. For E 8001, cur ve cos φ = f(P) should refer to curve B. default values of setting are as shown in curve B.

Reactive power control, Reactive standard curve Q= f(V)

Qmax

-Qmax

V2sV1s

V1iV2i

V2i=0.90Vn

V2s=1.10Vn

V1s=1.08Vn=QuVlowRate

V2i=0.92Vn=QuVlowRate

0.9

Upper limit

capactive

inductive

f (P)

Lower limit

Power Lower

Power Upper

curve A

0.3

0.7

0.9

Upper limit

capactive

inductive

f (P)

Lower limit

Power Lower

Power Upper

curve B

0.3

0.7

0.2

0.8

Ope ratio n Metho dOpe ratio n Metho d

b) Language This inverter provides several languages for customer to choose.

﹦﹦ ﹦ ﹦La ngu age ﹦﹦ ﹦ ﹦

Eng lish

Ger man Fre nch

g) Power limits User can set the power limit here, the setting value is from 0.00-1.00.

h) Grid Usually end user do not need to set the grid parameters. All default value have been set before leaving factory according to safety rules. If need to reset, any changes should according to the requirement of local grid.

﹦﹦ ﹦Powe r Limit s ﹦﹦ ﹦ >Pr opo rtio n

0.00

﹦﹦ ﹦ ﹦ Gri d ﹦﹦ ﹦ ﹦

>Vac U pper

000 .0

Parameter Comment

Normally

Vac upper

Voltage high protect

Vac lower Voltage low protect

Vac upper slow Voltage high slow protect

Vac lower slow Voltage low slow protect

Fac upper Frequency high protect

Fac lower

Frequency low protect

Fac upper slow Frequency high slow protect

Fac lower slow Frequency low slow protect

Vac 10m avg 10 min voltage high protect

Apply to EN50438_NL.

FreqSetPoint

FreqDropRate

Frequency set point

Frequency droop rate

i) Export control With this function the inverter can control energy expor ted to the grid. Whether having this function is based on user’s wishes. Choose”Enable”in Mode Select means user must install a meter to monitor energy exported to the grid. There are user value and factory value. The factory value is default which can not be charged by user. The user value setting by installer must be less than the factory value and within the range of 0KW to 6K W. Choose”Disable” means the function will be shut off. Press up and down button to select and press”OK” to confirm.

j) Relay Control Relay Control is an optional function which can control designated load intelligently by consuming the surplus energy when feed in power reaches certain value. For specific operation, please refer to “ Load remote control installation guide”.

Rel ay Con trol

Ope ratio n Metho dOpe ratio n Metho d

﹦﹦ ﹦

P(u ) Funct ion

﹦﹦ ﹦

Mod e Selec t

f )P(u) Function The device is suitable for Australia if the “Enable” is chosen.

>En able<

>Re lay1 s ettin g >Re lay2 s ettin g

k) DRM Function User can choose whether using the DRM function or not.

﹦﹦ ﹦DR M Fun ction

﹦﹦ ﹦ ﹦

>Mo de Sele ct

Dis able

m) Reset consume Reset consume is to reset load, user can reset the load if the inverter is plugged in a smart plug. Press up or down button to select and press “ok” to conrm.

n) Reset Feed in User can reset the meter. Press up or down button to select and press “ok” to conrm.

o) Reset error logs User can reset the error log here. Press up or down button to select and press “OK” to confirm.

﹦﹦ ﹦

Whe ther Res et

p) Start guide This interface makes user set initial setting of the inverter again possible.

﹦﹦ ﹦

Res et Load

﹦﹦ ﹦ ﹦

Res et Load 1

>No <

﹦﹦ ﹦Res et Meter ﹦﹦ ﹦ ﹦

Res et

>No <

﹦﹦ ﹦

Start guide

﹦﹦ ﹦

38 39

Ope ratio n Metho dOpe ratio n Metho d

Res et error l ogs ﹦﹦ ﹦

>Start

● History

The history function contains four aspects of the information: Inverter yield, load consume, feed in energy and error logs. Press up and down to select ,and press “OK” to confirm the selection, press “ESC” to return to Menu.

a) Inverter Yield The inverter yield function contains energy generated by today, yesterday ,this month ,last month and total. Press up and down button to review the parameter, Press “ESC” to return to history.

﹦﹦ ﹦ ﹦ His tory ﹦﹦ ﹦﹦

>In verter Yie ld

Loa d consu me

﹦﹦ ﹦ ﹦ Yie ld ﹦ ﹦﹦ ﹦

>Toda y:

00. 0KW H

Fee d in energ y

b) Load consume User can check the load consumption if the device is plugged in a smart plug.

c) Feed in energy Thi s function is made user check fe ed in ene rgy pos sible .

﹦﹦ ﹦ ﹦

Loa d consu me

﹦﹦ ﹦ ﹦

>Lo ad 1 cons ume Loa d 2 consu me

﹦﹦ ﹦ ﹦

Fee d in en ergy

﹦﹦ ﹦ ﹦

>Toda y:

00. 0KW H

l) Reset energy User can reset the energy record here. Press up or down button to select and press “OK” to confirm.

﹦﹦ ﹦Res et energ y ﹦﹦﹦ ﹦

Whe ther Re set

d) Error logs The Error log contains error information happened, It can record for three items. Press up and down button to review parameter, Press“ESC” to return to History.

﹦﹦ ﹦ ﹦ Abo ut ﹦﹦ ﹦ ﹦

●Abo ut

This interface shows information of the inverter, include serial number, machine type, master DSP1, slave DSP2 and manager.

﹦﹦ ﹦ ﹦Err or lo g ﹦ ﹦ ﹦﹦

No er ror

7. Troubleshooting

7.1 Trouble sh ooting

This section contains information and procedures for solving possible problems with X1 series inverters, and provides you with troubleshooting tips to identify and solve most problems that could occur with the X1 series inverters. This section will help you narrow down the source of any problems you may encounter. Please read the following troubleshooting steps. Check warnings or fault messages on System Control Panel or Fault codes on the inverter information panel. If a message is displayed, record it before doing anything further. Attempt the solution indicated in below table.

40 41

Trou blesh ootin g

Mac hine Typ e Mai n DSP 1

Trou blesh ootin g

Trou blesh ootin g Trou blesh ootin g

● If your inverter's information panel is not displaying a Fault light, check the

following list to make sure that the present state of the installation allows proper operation of the unit.

— Is the inverter located in a clean, dry, adequately ventilated place? — Have the DC input breakers been opened? — Are the cables adequately sized and short enough? — Are the input and output connections and wiring in good condition? — Are the configurations settings correct for your particular installation? — Are the display panel and the communications cable properly connected and undamaged?

7.2 Routine maintenance

Contact SolaX Customer Service for further assistance. Please be prepared to describe details of your system installation and provide model and serial number of the unit.

Inverters do not need any mainteinance or correction in most condition,but if the inverter often loses power due to overheating,this can be the following reason:

● The cooling fins on the rear of house are coverd by dirts.

Clean the cooling fins with a soft dry cloth or brush if necessary.

Only trained and authorized professional personnel who are familiar with the requirements of safety was allowed to perform servicing and maintenance work.

► Safety checks

Safety checks should be performed at least every 12 mouths by manufacturer's qualified person who has adequate training,kownledge,and practical experience to perform these tests.The data should be recorded in an equipment log.If the device is not functioning properly or fails any of test,the device has to be repaired.For safety check details ,refer to this manual,section 2 Safety instruction and EC Directives.

►Maintain periodically

Only qualified person may perform the following works. During the process of using the inverter,the manage person shall examine and maintain the machine regularly.The concrete operations are follow. 1: Check that if the cooling fins on the rear of house are covered by dirts, and the machine should be cleaned and absorbed dust when necessary. This work shall be check time to time. 2: Check that if the indicators of the inverter are in normal state,check if the keys of the inverter are in normal state,check if the display of the inverter is normal.This check should be performed at least every 6 months. 3: Check that if the input and output wires are damaged or aged.This check should be performed at least every 6 months. 4: You should get the inverter panels cleaned and their security checked at least every 6 months.

8. Decommissioning

8.1 Disman tling the Inverte r

Disconnect the inverter from DC Input and AC output. Wait for 5 minutes for de-energizing. Disconnect communication and optional connection wirings. Remove the inverter from the bracket. Remove the bracket if necessary.

If possible, please pack the inverter with the original packaging. If it is no longer available, you can also use an equivalent carton that meets the following requirements. Suitable for loads more than 30 kg. With handle. Can be fully closed.

8.3 Storage and Transportation

Store the inverter in dry place where ambient temperatures are always between -20 °C - +60 °C.Take care of the inverter during the storage and transportation,keep less than 4 cartons in one stack.

8.2 Packaging

When the inverter or other related components need to be disposed. Have it carried out according to local waste handling regulations. Please be sure to deliver wasted inverters and packing materials to certain site, where can assist relevant department to dispose and recycle.

Dec ommis sioni ng

SolaX Power X1 Series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual