solaredge P505, P500, P401 User Manual

Power Optimiser

For Australia
Module Add-On

P401 / P500 / P505

25

YEAR

WARRANTY

POWER OPTIMISER

PV power optimisation at the module-level

Specically designed to work with SolarEdge
inverters

Up to 25% more energy

Superior efciency (99.5%)

Mitigates all types of modules mismatch­loss, from manufacturing tolerance to partial
shading

solaredge.com

Flexible system design for maximum space
utilization

Fast installation with a single bolt

Next generation maintenance with module
level monitoring

Module-level voltage shutdown for installer
and reghter safety

Power Optimiser For Australia

Module Add-On

P401 / P500 / P505

Optimiser Model
(Typical Module Compatibilty)

P401

(60&70 Cell modules)

P500

(for 96-cell

modules)

P505

(for higher current

modules)

INPUT

Rated Input DC Power

Absolute Maximum Input Voltage
(Voc at lowe󰎯 temperature)

MPPT Operating Range 8 - 60 8 - 80 12.5-83 Vdc

Maximum Short Circuit Current (Isc) 11.75 10.1 14 Adc

Maximum Eciency 99.5 %

Weighted Eciency 98.8 %

Overvoltage Category II

OUTPUT DURING OPERATION (POWER OPTIMISER CONNECTED TO OPERATING SOLAREDGE INVERTER

Maximum Output Current 15 Adc

Maximum Output Voltage 60 60 85 Vdc

OUTPUT DURING STANDBY (POWER OPTIMISER DISCONNECTED FROM SOLAREDGE INVERTER OR SOLAREDGE INVERTER OFF

Safety Output Voltage per Power Optimiser 1 ± 0.1 Vdc

(1)

400 500 505 W

60 80 83 Vdc

)

)

STANDARD COMPLIANCE

EMC FCC Part 15 Class B, IEC61000-6-2, IEC61000-6-3

Safety IEC62109-1 (class II safety), UL1741

RoHS Ye s

Fire Safety VDE-AR-E 2100-712:2013-05

INSTALLATION SPECIFICATIONS

Maximum Allowed Sy󰎯em Voltage 1000 Vdc

Dimensions (W x L x H) 129 x 153 x29.5 129 x 153 x 33.5 129 x 162 x 59 mm

Weight (including cables) 655 750 1064 gr

Input Connector

Input Wire Length 0.16 / 0.9

Output Connector MC4

Output Wire Length 1.2 m

Operating Temperature Range -40 to +85 ˚C

Protection Rating IP68 / NEMA6P

Relative Humidity 0 - 100 %

(2)

MC4

(2)

(4)

(2)

MC4

0.16 m

(1) Rated power of the module at STC will not exceed the optimiser “Rated Input DC Power”. Modules with up to +5% power tolerance are allowed
(2) For other connector types please contact SolarEdge
(3) Dual version for parallel connection of 2 modules; P/N: P485-4RMDMRM. In a case of odd number of PV modules in one 󰎯ring it is allowed to in󰎯all one P485 dual version power optimiser
connected to one PV module. When connecting a single module seal the unused input connectors with the supplied pair of seals
(4) Longer inputs wire length are available for use. For 0.9m input wire length order P401-xxxLxxx

Single Phase

PV System Design Using a Solaredge Inverter

Minimum String Length (Power
Optimisers)

Maximum String Length (Power Optimisers) 25 25 50

Maximum Nominal Power per String

Parallel Strings of Different Lengths or Orientations Ye s

(5) It is not allowed to mix P505 with P401/P500 in one 󰎯ring
(7) It is allowed to in󰎯all up to 13,500W per 󰎯ring when the maximum power difference between each 󰎯ring is 2,000W
(6) If the inverters rated AC power ≤ maximum nominal power per 󰎯ring, then the maximum power per 󰎯ring will be able to reach up to the inverters maximum input DC power Refer to: https://www.solaredge.
com/sites/default/les/se-single-󰎯ring-power-optimizer-application-note-aus.pdf

© SolarEdge Technologies Ltd. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc.
All other trademarks mentioned herein are trademarks of their respective owners. Date: 03/2021/V01/ENG AUS. Subject to change without notice.

P401, P500 8 9 16

P505 6 8 14

(5)

HD-WAVE

(6)

(6000

5700

with SE8000H,

SE10000H)

Single Phase

(6)

5250

Three Phase

Residential

(6)

5625

Three Phase
Commercial

(7)

11250

W