INSTALLATION INSTRUCTIONS
LCD Wall Mount
LC D-20 3
75x75
100x1 00
CA UT ION: DO N OT EX CEE D MAXIMUM
LISTE D WEI GHT C APAC ITY. SE RIO US
INJURY O R PRO PER TY DA MAG E MAY
OCCUR !
23"
MAX
30kg
30kg
(66lbs)
(66lbs)
MAX
MAX
ISSUED: OCT. 2012
NOTE: Rea d the entire instr uction manual be fore you st art ins tallati on and as sembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
Component Checklist
IMPORTANT: Ensure t hat y ou ha ve re ceived al l par ts ac cor ding to the c omp one nt ch eck list prio r to in sta lli ng. If
any p art s are m iss ing or faulty, co nta ct the sell er fo r a rep lac ement.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. Use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Package M
M4x14 ( x4)
Package W
M-A
ST6.3 x55 ( x2)
W-A
M5x14 ( x4)
M-B
concr ete a nch or (x 2)
W-B
D5 wash er (x 4)
M-C
D6 wash er (x 2)
W-C
21
1.Disassemble VESA Plate
2a. Mount on Wood Stud Wall
Use the screwdriver to loosen the screw in order to
separate the VESA plate from the wall mount.
55mm
55mm
55mm
(2.2")
2.2"( )
(2.2")
ø 4.5mm
(ø 3/16")
1
Fin d and ma rk the exact
loc ation of mou nting holes.
2
3
2b. Mount on Solid Brick and Concrete Block
60mm
60mm
60mm
2.4"( )
(2.4")
(2.4")
√
ø 10mm
(ø 3/8")
1
Mar k the ex act
loc ation of
mou nting holes
2
Drill pilot holes
X X
W-AW-C
√
Drill pilot holes
X X
Screws the wall
plate onto the
wall
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder
is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
3
Screws the wall
plate onto the
wall
W-B
W-C
W-A
WARNING
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35 mm) for using the concret e anchors. Do not drill into mortar joints! Be sure to
mount in a soli d part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must veri fy that the sup porting su rface will safely support the combined load of the
equipment and all attached hardware and components.
4
3. Install the VESA Plate
4. Hang the display onto the Wall Plate
TV
TV
TV
Tig hte n
M-A/M-B
M-C
wall
Top of disp lay
wall
Screw V ESA pl ate o nto t he display.
Tig hten all screws b ut do n ot ov er ti ghten.
Hook the VESA plate(attached the display) onto the wall plate and tighten the screws to secure.
Maint ena nce
• Check t hat t he br ack et is s ecure and sa fe to u se at r egu lar intervals (at l eas t eve ry three months ).
• Pleas e con tac t you r dealer if you hav e any q ues tio ns.
65
Loading...