softDSP SDS 200 SoftScope User Manual

Download

Page 1

User’s Guide

- SDS 200 -

- SoftScope -

PC Based Digital Oscilloscope

www.softdsp.com

Page 2

soft

This document is being f urnis hed b y

soft

DSP Co., Ltd. for inform ation purpos es o nl y to licensed users of the SDS 200 and is furnished on as “AS IS” basis, that is, without any warranties, whatsoever, expressed or implied.

SDS 200 and SoftScope are trademarks of

soft

DSP Co., Ltd.

Other brand and product names are trademarks or registered trademarks of the respective holders. Microsoft is a registered trademark and Windows, the Windows logo are registered trademarks of the Microsoft Corporation.

Information in this document is subject to change without notice and does not represent a commitment on the part of

soft

DSP Co., Ltd.

Page 3

FCC NOTICE

THIS DEVIDE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITION: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected.

- Consult the dealer of an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interference cause by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Page 4

WARRANTY

This softDSP instrument product is warranted to be free from defects in material and workmanship for a period of one year from the date of shipm ent. During the warranty period, softDSP Co., Ltd. will at its option, either will repair or replace the defective product. But, the foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the buyer, Buyer-supplied soft ware or interfacing, unauthori zed modification or misuse, operation outs ide of the environmental specif ications for the product, or improper site preparation or maintenance.

Product Name PC Based Digital Oscilloscope Model Name SDS 200 Warranty Period one year from the date of purchase At the time of purchase

ASSISTANCE

Product maintenance agr eements and other cus tomer assistance agreem ents are available for softDSP. For any assistance, contact your nearest softDSP Sales and Service office. Addresses are provided in this manual. Our homepage address is “http://www.softdsp.com”.

Page 5

SAFETY SUMMARY

Do not install subs titute parts or perform any unauthorized modif ication to the product. Retur n the product to a s oftDSP Sales and Ser vice Office for service and repair to e nsure that safet y features are maintained.

Observe Maximum Working Voltage

Do not use this product on bare wires above 42Vpk, AC 30Vrms and DC 60V.

Product Damage Precautions

Do not open the cover an d attempt any repairs. An e le c tric s hoc k or ac cident may be caused by opening the cover or improper handling. If you sus pect there is damage to this product, you must have it inspected by qualified service personnel. Do not drop the product. This product contains fragile components that can be damaged by high impact. Take care to prevent the product from dropping on the floor or other hard surfaces. To avoid electric shock, do not operate this product in wet or damp conditions. Do not operate near flammable materials.

Page 6

Minimum System Requirements

To install and run SoftScope, you should have the following;

Operating System

Windows 98/ME/2000

CPU/Mainboard

Pentium 200MHz , USB equipped mainboard

Memory

32MByte

HDD

20MByte

Graphic Card

Microsoft DirectX supported Screen resolution: 800x600 Color depth: 16bit

Page 7

Table of Contents

Ch 1. Introduction.............................................................................................1

1. What is SDS 200/SoftScope ?...............................................................1

SDS 200 ...........................................................................................1

SoftScope.........................................................................................2

2. Hardware Specification..........................................................................3

3. SoftScope Installation............................................................................5

4. SDS200 Setup.......................................................................................8

5. Setup sds200.inf Manually.....................................................................9

6. Warning! .............................................................................................. 11

7. Calibration............................................................................................13

Ch 2. How to use SDS 200/SoftScope...........................................................14

1. Simple Measurement...........................................................................14

2. Basic Operations.................................................................................16

Change Vertical Scale(Volt/Div)......................................................16

Change Horizontal Scale(Time/Div)................................................17

Measurement Using Cursor............................................................19

Measurement by Icon.....................................................................20

Change Trigger Level & Trigger Point.............................................22

Single Shot/Stop Mode...................................................................23

Put Label on The Screen................................................................23

Print/Save Waveform......................................................................24

Ch 3. Advanced Technique ............................................................................26

1. Advanced Trigger.................................................................................26

Edge Trigger...................................................................................26

Logic Trigger...................................................................................27

Pulse Trigger...................................................................................27

Delay Trigger..................................................................................27

2. FFT......................................................................................................28

3. Math.....................................................................................................29

Page 8

Ch 4. Toolbars, Menus, Dialog boxes & Screen Information......................30

1. Toolbar.................................................................................................30

2. Menu....................................................................................................31

File..................................................................................................31

View................................................................................................31

Channel..........................................................................................32

Display............................................................................................32

Math/FFT........................................................................................33

Run/Stop.........................................................................................33

Trigger............................................................................................33

Measure..........................................................................................33

Util ..................................................................................................34

Help................................................................................................34

3. Screen Information..............................................................................35

4. Option Dialog Box................................................................................37

Ch 5. Appendix ...............................................................................................38

1. Three Operational Modes of SDS 200.................................................38

Realtime mode................................................................................38

RIS(Random Interleaved Sampling) mode.....................................38

Roll mode........................................................................................38

2. Software Calibration............................................................................38

3. Firmware Update.................................................................................40

Page 9

Chapter 1. Introduct ion

Ch 1. Introduction

1. What is SDS 200/SoftScope ?

SDS 200

SDS 200 developed by softDSP Co., Ltd. is a portable PC-based Digital Oscilloscope.

High performance

SDS 200 has the following features: 200MHz analog bandwidth, 5GS/s equivalent sampling, 100MHz real-time sampling.

USB connected

SDS 200 uses USB that supports plug’n play, w ith 12Mbps communication speed.

Advanced trigger

SDS 200 has advanced trigger circuitry so that it can detect many complex signals.

Best performance for your dollar

SDS 200 has many featur es that is comparable to the high speed stand-alone DSOs. But it costs a fraction of the price.

No external power required

SDS 200 does not need an external power source, because it is bus-powered from USB.

Page 10

Chapter 1. Introduct ion

SoftScope

SoftScope is a Windows software that controls SDS 200.

Easy to use

SoftScope is easy to use. It is intuitive and easy to understand.

Big screen

SoftScope uses 500 x 400 screen size.

Various data format processing

SoftScope can save waveform in the following formats: text file, jpg/bmp graphic file, MS excel/word file.

Fast screen update rate

SoftScope uses Micr osoft DirectX , so that it gi ves upto sc reens per secon d update rate. ( under Windows98, Pentium II environment)

Many kinds of measurements

SoftScope has 23 measurement functions.

The analog scope effect

SoftScope uses digital persistence and histogram method so that the display resembles an analog oscilloscope screen.

Page 11

Chapter 1. Introduct ion

2. Hardware Specification

Input

Max. sample rate Realtime sampling: 100 MS/s using one channel, 50MS/s using two

channels

Equivalent sampling: 5GS/s Channels 2 Bandwidth 200 MHz (-3dB)

Single shot bandwidth:20MHz Vertical resolution 9 bits/channel Gain range 10mV ~ 10V/div @ x1 probe

(10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V, 10V/div

1,2,5 sequence)

100mV ~ 100V/div @ x10 probe

1V ~ 1000V/div @ x100 probe Range 8 divisions Offset level +/-4 divisions Coupling AC, DC Offset increments 0.02 div Impedance 1M ohm DC accuracy +/-3% Input protection 42Vpk (DC + peak AC < 10 kHz, without external attenuation)

Timebase

Timebase range 2ns/div ~ 10s/div

( 2ns, 4ns, 10ns, 20ns, 40ns, 100ns, 200ns, 400ns, 1us,

2us, 4us, 10us, 20us, 40us, 100us, 200us, 400us, 1ms,

2ms, 4ms, 10ms, 20ms, 40ms, 100ms, 200ms, 400ms, 1s,

2s, 4s, 10s /div 1-2-4 sequence) Acquisition mode Equivalent sampling: 2ns/div ~ 4us/div

Realtime sampling: 10us/div ~ 400ms/div

Roll mode: 1s/div ~ 10s/div Range 10 divisions Pre/Post trigger 0% ~ 1000% Time resolution 200ps Buffer size 10K samples

Page 12

Chapter 1. Introduct ion

Trigger

Type Edge trigger: Rising edge, falling edge

Logic trigger: AND, NAND, OR, NOR, XOR, XNOR

Pulse trigger: Less than width, more than width (10ns ~ 167ms)

Delay trigger: By event (1~16,777,215), by time (10ns ~ 167ms) Mode Auto, Normal and Single Autoset Yes Range 10 divisions Trigger level +/-4 divisions Settabillity 0.02 div increments

Math

Measurements Vp-p, Vmax, Vmin, Vmean, Vrms, Vamp, Vhigh, Vlow, positive

overshoot, negative overshoot, cycle mean, cycle rms, period,

frequency, positive pulse width, negative pulse width, rise time

(10%~90%), fall tim e (10%~90%), positive dut y cycle, negati ve duty

cycle Cursor Time/frequency difference, voltage difference

Frequency only in FFT mode Math Addition, Subtraction, Multiplication, Division FFT Rectangular, Hanning, Hamming, Blackman Window

Physical

Interface Universal Serial Bus (USB) Power No external power source required.

Bus-powered from USB Dimensions 5.1" x 4.4" x 1.5"

Page 13

Chapter 1. Introduct ion

3. SoftScope Installation

Caution!) You must install ‘SoftScope’ before using SDS 200.

1. While in Windows, insert the installation CD into the CD-ROM drive.

2. The installatio n should start up a utomatically. Otherwise in Windows Ex plorer, switch to the CD-ROM drive and run Setup.exe.

3. The SoftScope Installation is started. Click Next to continue.

4. If you accept the license agreement, click Yes to continue.

Page 14

Chapter 1. Introduct ion

5. Fill in the user information and serial number. Click Next to continue.

6. Choose a destination directory. Click Next to continue.

7. Check the setup information. Click Next to start copying of files.

Page 15

Chapter 1. Introduct ion

8. This Status dialog is displayed during copying of files.

9. After Installing SoftScope, the installation program will check the DirectX version of your computer. If it is later than 6.0, the installation program will skip the DirectX Setup.

9.1 If it is earlier than 6.0, the DirectX Setup will start up automatically.

9.2 Follow the directions of the DirectX Setup.

9.3 You will see the Rest art message box in the last step of DirectX Setup. Click Ok, but your computer will not restart in this step, it will go to step 10.

Caution!) You must install DirectX 6.0 or later to use SoftScope.

10. Check Yes and click Finish to reboot your computer.

Caution!) Reboot your computer to use SoftScope correctly.

1 1. The installation is complete.

Page 16

Chapter 1. Introduct ion

4. SDS200 Setup

Caution!) SoftScope must be installed before using SDS 200. This setup process is done

once; at the first time of connection.

1. Connect the A-Type Plug of USB cable to your PC’s USB port.

2. Connect the B-Type Plug of USB cable to SDS 200’s USB port.

3. SDS 200 will be detected automatically. (The picture is captured under Windows98 SE environment)

Page 17

Chapter 1. Introduct ion

5. Setup sds200.inf Manually

When sds200.inf file is not be detected automatically, you see the following dialog box.

In this case you must install sds200.inf file manually.

1. Choose ‘Search for a suitable driver for my device’ button. Click Next to continue.

2. Specify a location. Click Next to continue.

Page 18

Chapter 1. Introduct ion

3. The sds200.inf f ile is located in SoftScope CD-R OM root directory. Specify the location by

either entering or browsing.

4. sds200.inf file is detected automatically. Click Next to continue.

5. Click Finish.

Page 19

Chapter 1. Introduct ion

6. Warning!

We recommend using High Color(16 bit) mode. With some graphic cards with 32 bit color depth, SoftScope doesn't work. SoftScope doesn’t support 24 bit color mode. If you see the following error message when you run SoftScope. Check the following two items.

Check if DirectX is installed and work well.

Under Window98 environm ent, run DXDiag.ex e which is in C:\Pr ogram Files\DIR ECTX\SETUP directory(The default directory may be different if you choose other directory at DirectX setup). Under Windows2000 environment, run DXDiag.exe which is in C:\WinNT\System32. Under WindowsME environment, run DXDiag.exe which is in C:\WinNT\System.

In the <display> section, run <DirectDraw Test>. Check if DirectX works well.

Page 20

Chapter 1. Introduct ion

Check if you're using High Color(16 bit) mode.

Under Control Panel choose ‘Display’ applet.

3. Set High Color (16bit) mode and click OK to continue.

Page 21

Chapter 1. Introduct ion

7. Calibration

SDS 200 calibration

1. When manufactured, SDS 200 is calibrated manually to obtain maximum performance.

2. You may calibrate SDS 200 5 or 6 months after purchase.

Probe Compensation

1. You must use a probe with more than 200MHz bandwidth to get undistorted signal.

2. Probe should be compensated whenever it is connected for the first time.

3. Connect calibration signal to channel 1, then push AUTOSET.

4. Check the shape of the displayed waveform.

5. Adjust the probe until the displayed waveform is compensated.

Page 22

Chapter 2. How to use SDS 200/SoftScope

Ch 2. How to use SDS 200/SoftScope

1. Simple Measurement

1. Start SoftScope.

2. SoftScope check s the internal state of SDS 200, U SB communication status and then read

initialization data.

3. Connect channel 1 probe to the calibration terminal.

Push the autoset button.

5. SoftScope sets vertical/horizontal scale automatically.

6. Join dots to a solid line.

A. SoftScope displays the data from SDS200 as a dotted line. B. To see the waveform more clearly, push the line-join icon.

7. Add persistence effect.

A. Persistence effect is analog-scope like effect that remembers the history of displayed

waveforms. With persistence effect, you can see the more frequent line clearer.

B. Change the persistence effect coefficient.

Page 23

Chapter 2. How to use SDS 200/SoftScope

8. Change the intensity of the waveform.

A. Just as in changing the persistence effect, you can change the intensity. B. By changing the scroll bar in the menu, you can see a more/less distinct line.

Page 24

Chapter 2. How to use SDS 200/SoftScope

2. Basic Operations

Change Vertical Scale(Volt/Div)

1. Change vertical scale(volt/div) from panel.

Push voltage scale change panel.

B. Set the volt/div scale with mouse or keyboard. C. Vertical scale is changed.

2. Change vertical scale(volt/div) with mouse button.

Push voltage scale change icon.

Page 25

Chapter 2. How to use SDS 200/SoftScope

B. Mouse icon is changed to number 1. C. Push the left/right mouse button to change volt/div. D. With mouse that supports scroll button, change the voltage offset.

3. Change vertical scale(volt/div) from menu and hot-key.

A. Channel ÆCh1 Setting ÆVolt Scale B. Press the appropriate hot-key.

4. Change AC/DC setting.

A. Push the AC/DC icon to change. B. Push the same button once more to restore.

Change Horizontal Scale(Time/Div)

1. Change horizontal scale(time/div) from panel.

Push time scale change panel.

B. Set the time/div scale with mouse or keyboard.

Page 26

Chapter 2. How to use SDS 200/SoftScope

C. Horizontal scale is changed.

2. Change horizontal scale(time/div) with mouse button.

Push time scale change icon.

B. Cursor is changed to “T”. C. Push the left/right mouse button to change volt/div. D. With mouse that supports scroll button, change the trigger point.

Page 27

Chapter 2. How to use SDS 200/SoftScope

3. Change horizontal scale(time/div) from menu and hot-key.

A. Channel Æ Time Scale. B. Press the appropriate hot-key.

Measurement Using Cursor

Measure voltage and time offset simply using mouse.

Push icon and the cursor is changed to cross .

B. Push left mouse button, and the cross lines appear. C. Drag the mouse button to the point you want to measure.

D. Release the left mouse button, the voltage difference an d time difference wil l be shown

at the status bar.

E. Push right mouse button, and the cross lines disappear.

Page 28

Chapter 2. How to use SDS 200/SoftScope

Measurement by Icon

SDS 200 has many measurement functions.

Pk-Pk

-Peak-to-peak = Max – Min

-Measured over the entire waveform

Max

-Voltage of the absolute maximum level

-Measured over the entire waveform

Min

-Voltage of the absolute minimum level

-Measured over the entire waveform

Amp

-Amp = Base – Top

-Measured over the entire waveform

Base

-Voltage of the statistical minimum level

-Measured over the entire waveform

Top

-Voltage of the statistical maximum level

-Measured over the entire waveform

Upper threshold

-Voltage of the 90% level from base to top

Middle threshold

-Voltage of the 50% level from base to top

Lower threshold

-Voltage of the 10% level from base to top

Mean

-The arithmetic mean over the entire waveform

Cycle mean

-The arithmetic mean over the first cycle in the waveform

RMS

-The Root Mean Square voltage over the entire waveform

Page 29

Chapter 2. How to use SDS 200/SoftScope

Cycle RMS

- The Root Mean Square voltage over the first cycle in the waveform

Positive Overshoot

- Positive Overshoot = (Max - Top)/Amp x 100 %

- Measured over the entire waveform

Negative Overshoot

- Negative Overshoot = (Base - Min)/Amp x 100 %

- Measured over the entire waveform

Period

- Time to take for the first signal cycle to complete in the waveform

- Measured in seconds

Frequency

- Reciprocal of the period of the first cycle in the waveform

- Measured in Hertz(Hz)

Rise time

- Time taken from lower threshold to upper threshold

Fall time

- Time taken from upper threshold to lower threshold

Positive Duty Cycle

- Positive Duty Cycle = (Positive Pulse Width)/Period x 100%

- Measured of the first cycle in waveform

Negative Duty Cycle

- Negative Duty Cycle = (Negative Pulse Width)/Period x 100%

- Measured of the first cycle in waveform

Positive Pulse Width

- Measured of the first positive pulse in the waveform

- The time between the 50% amplitude points

Negative Pulse Width

- Measured of the first

- View next icons

Page 30

Chapter 2. How to use SDS 200/SoftScope

Change Trigger Level & Trigger Poi nt

1.Set the trigger input source.

A. With only one channe l on, trig ger inp ut source is autom aticall y set to the c hannel. W ith 2

channels on, you can choose trigger input source between the two.

B. Change trigger source from the radio-button.

C. Change trigger source from menu bar.

EX) Trigger Æ Trigger Source CH1 or CH2

D. Change trigger input source using hot key.

2. Change the trigger level.

Move the trigger level icon, you can move the trigger level.

B. Input the trigger level from editor

3. Change the trigger point.

Move the trigger point icon, you can move the trigger point.

B. Input the trigger point from editor.

4. Change the trigger condition.

Push the trigger up/down icon to change trigger condition.

B. Use menu or hot-key. ( Trigger Æ Trigger Up/Down )

5. Set delay on/off.

Push the delay button to set delay on or off.

B. When delay on, the trigger point separates from the horizontal expansion point. The

horizontal expansion point stays at the center of the screen.

Page 31

Chapter 2. How to use SDS 200/SoftScope

Single Shot/Stop Mode

1. Change state to stop or single shot.

A. Push the stop button

, SDS200 is in stop state.

B. Every operation is the same as in the running state.

2. Single-shot action.

A. Push the single-shot but ton

to acquir e only 1 waveform af ter the trigger condition

you set.

B. Single-shot is available only in Real Time mode.

C. Push the single-shot button again to pause, SDS 200 waits for the trigger signal again.

Put Label on The Screen

1. Add a label on the screen.

Push the label icon.

B. The mouse cursor is changed to 'I' shape. C. Push the left mouse button. D. Input string. E. Change the text/back color. F. Push the confirm button to finish. G. Change the label by clicking the label again.

Page 32

Chapter 2. How to use SDS 200/SoftScope

Print/Save Waveform

1. Save acquired waveform in the following formats.

A. Text File B. JPG/BMP File C. Excel File D. Word File

2. Save as text format.

A. Push the save button

and the dialog box appears.

B. Enter the directory that you want to save the data file in. C. Enter the name of data file that you want to save. D. Select type 'DAT' at option. E. Push the save button.

3. Save as JPG/BMP format.

Push the save button.

B. Enter the title you want to give. C. Enter the directory you want to save the data file in. D. Enter the name of data file you want to save. E. Select type 'BMP/JPG' at option. F. Push the save button.

Page 33

Chapter 2. How to use SDS 200/SoftScope

4. Copy the image into clipboard.

A. Select Copy from the File menu. B. Waveform is copied into clipboard. C. Paste the image into any program that supports clipboard paste.

5. Transfer the data to MS Excel using ActiveX automation.

A. Select Copy at the File menu. B. MS Excel is activated and then data is transferred by using ActiveX.

6. You can save the data to MS Word using ActiveX automation.

A. Select Copy at the File menu. B. MS Word is activated and then data is transferred by using ActiveX.

7. Print the waveform.

Push the print button.

Push the preview button to preview the image.

C. Push 'OK' button.

Page 34

Chapter 3. Advanced Technique

Ch 3. Advanced Technique

1. Advanced Trigger

You can return to normal trigger mode by uncheck Logic, Pulse, Delay check box in the advanced trigger dialog box.

(Normal trigger mode) (Advanced trigger mode)

Edge Trigger

The Edge Trigger generates a trigger when the source signal passes through a specified level in either positive or negative direction, set by the user. This is the same trigger type found in a conventional analog oscilloscope. The source, the slope and the level must be set for Edge Trigger operation.

Source

: CH1/CH2

-Selects the trigger source.

Slope

: Up Edge/Down Edge

-Selects the slope of the source.

Level

: +/- 4 vertical screen divisions (Full screen range)

-Selects the level of the input signal where the Edge Trigger is generated. The level is selected by trigger level pointer at the right-hand side of the display screen and the source is selected from the tool bar radio button.

Page 35

Chapter 3. Advanced Technique

Logic Trigger

The Logic Trigger generates a trigger depending on the logical relation between the state of the two input channels. AND, NAND, OR, NOR, XOR, XNOR Logic Triggers are available and the two input states can be negated if selected.

Ch1 state

: High/Low

-Selects the state of channel 1 signal for Logic Trigger input

Ch2 state

: High/Low

-Selects the state of channel 2 signal for Logic Trigger input

Logic type

: AND, NAND, OR, NOR, XOR, XNOR

-Selects logic type

Pulse Trigger

The Pulse Trigger generates a trigger if the pulse width of the input signal is either less or more than the preset time.

Equation

: Less than/More than

- Selects whether the trigger is generated when the pulse is less than or more than the

preset pulse time value.

Time

: 10ns ~ 167ms

- Selects the pulse width time

Delay Trigger

The Delay Trigger generates a trigger by waiting for a preset time or number of events after a primary trigger from combination of edge, logic and pulse trigger is generated and when the first trigger from the secondary trigger source is detected.

Equation

: By time/By event

- Selects the delay condition either by time or by event.

Delay condition

: By time (10ns ~ 167ms)/By event (1 ~ 16,777,215 events)

Page 36

Chapter 3. Advanced Technique

Secondary trigger source

: CH1/CH2

- Selects the trigger source of the secondary trigger.

Secondary trigger slope

: Rising/Falling

- Selects the slope of the secondary trigger.

2. FFT

Analyze the frequency component of the waveform using FFT(Fast Fourier Transform).

Push the FFT icon, and the FFT dialog box is appears.

Channel Sets input source to FFT analyze Window Type Sets digital filter type Scale Type Sets y scale to Linear or Log scale Vertical Scale Sets vertical scale Vertical Scale Sets offset

2. Move the FFT cursor over the FFT waveform to see the frequency component.

Page 37

Chapter 3. Advanced Technique

3. Math

Add/Subtract/Multiply/Divide the two waveforms.

Push the Math icon.

2. Select source 1, source 2 and operator from the dialog box.

Src1/Src2 Sets input source. Operator Sets operation method Vertical Scale Sets vertical scale Zero Position Sets offset

Page 38

Chapter 4. Toolbar, Menu & Dialog box

Ch 4. Toolbars, Menus, Dialog boxes &

Screen Information

1. Toolbar

1. Save As

-Saves current waveform as dat, bmp or jpg file

2. Load State

-Loads state file into current state

3. Save State

-Saves current state to file

4. Print

-Prints current waveform

5. Preview

-Previews current waveform

6. Option

-Shows option dialog box

7. Line Join

-Joins the dots to lines

8. Label

-Shows label on the screen

9. Persistence

-Sets persistence time

10. Intensity

-Sets intensity of the waveform

11. FFT

-Shows FFT dialog box

12. Math

-Shows Math dialog box

13. Cursor

-Shows measurement cursor

14. Channel 1 On

/ Off

-Sets channel 1 on

-Sets channel 1 off

15. Channel 1 AC

/ DC

-Selects DC coupling

-Selects AC coupling

16. Channel 1 Voltage Scale

-Changes vertical scale factor of Channel 1

17. Channel 2 On

/ Off

-Sets channel 2 on

-Sets channel 2 off

18. Channel 2 AC

/ DC

-Selects DC coupling

-Selects AC coupling

19. Channel 2 Voltage Scale

-Changes vertical scale factor of Channel 2

Page 39

Chapter 4. Toolbar, Menu & Dialog box

20. Time Scale

-Changes horizontal scale factor

21.Delay On

/ Off

-Sets trigger delay on

-Sets trigger delay off

22. Trigger Source

-Sets trigger source to a specific channel

23. Trigger Up

/ Down

-Triggers on the rising edge of the signal

-Triggers on the falling edge of the signal

24.

Trigger auto

/ Normal

-Enables free running waveform acquisitions

-Triggers only on valid trigger events

25. Advanced Trigger

-Shows advanced trigger dialog box

26. Run

/ Stop

-Starts waveform acquisitions

-Stops waveform acquisitions

27. Single Shot

-Executes a single-shot acquisition

28. Autoset

-Adjusts the vertical, horizontal, and trigger controls f or a usable display automatically

2. Menu

File

Name Sub Menu Operation Hot-key

Load State

Loads file to current file

Save State

Saves current state to file

Save As

Saves waveform as b

mp, jpg, dat file

Ctrl +S

Save As Word

Saves waveform as word file

Save As Excel

Saves wav eform as excel file

Copy

Saves waveform to clipboard

Ctrl + C Option Selects the waveform or screen option F6 Preview Previews the waveform F7 Print Prints the waveform Ctrl + P Exit

Stops the SoftScope and return

Ctrl + X

View

Name Sub Menu Operation Hot-key

File Toolbar Shows/Hides File Toolbar Ctrl + F1 Display Toolbar Shows/Hides Display Toolbar Ctrl + F2

Page 40

Chapter 4. Toolbar, Menu & Dialog box

FFT/Math Toolbar Shows/Hides FFT/Math Toolbar Ctrl + F3 Channel Toolbar Shows/Hides Channel Toolbar Ctrl + F4 Trigger Toolbar Shows/Hides Trigger Toolbar Ctrl + F5 Run/Stop Toolbar Shows/Hides Run/Stop Toolbar Ctrl + F6

Channel

Name Sub Menu Operation Hot-key

CH1 Setting On/Off

AC/DC Volt Scale ‘+’ Volt Scale ‘-’ Select Volt/Div Probe Attenuation

Changes ON/OFF Changes AC/DC Increases Voltage Decreases Voltage Changes Volt/Div Changes Probe Attenuation

Shift + F1

Shift + F2

Shift + F3

Shift + F4

Shift + F5

Shift + F6

CH2 Setting On/Off

AC/DC Volt Scale ‘+’ Volt Scale ‘-’ Select Volt/Div Probe Attenuation

Changes ON/OFF Changes AC/DC Increases Voltage Decreases Voltage Changes Volt/Div Changes Probe Attenuation

Shift + F7

Shift + F8

Shift + F9

Shift + F10

Shift + F11

Shift + F12

‘+’ Increases Time/Div Shift + Ins Time Scale

‘-‘ Decreases Time/Div Shift + Del Select Time Changes Time Ctrl + T Delay On/Off Changes Delay ON/OFF Ctrl + D Cursor Changes Cursor ON/OFF Ctrl + U

Display

Name Sub Menu Operation Hot-key

Line Join Joins the waveform with line Ctrl + J Label Inserts text to waveform Ctrl + L Persistence Changes the persistence effect Ctrl + E Intensity + Increases intensity of waveform Ctrl + Inc Intensity - Decreases intensity of waveform Ctrl + Del

Page 41

Chapter 4. Toolbar, Menu & Dialog box

Math/FFT

Name Sub Menu Operation Hot-key

Math Calculates several signal Ctrl + M FFT Changes signal to FFT Ctrl + F

Run/Stop

Name Sub Menu Operation Hot-key

Run/Stop Starts/Stops acquiring waveform Ctrl + R Single Shot Begins Single Shot operation Ctrl + H Auto Set Changes horizontal/vertical scale for waveform Ctrl + A

Trigger

Name Sub Menu Operation Hot-key

Trigger Source CH1 Selects CH1 from trigger source Shift+Ctrl+F1 Trigger Source CH2 Selects CH2 from trigger source Shift+Ctrl+F2 Trigger Up/Down Selects Up/Down from Trigger Up/Down Shift+Ctrl+F3 Normal/Auto Selects Normal/Auto from Trigger Normal/Auto Shift+Ctrl+F4 Advanced Trigger Selects Advanced trigger Shift+Ctrl+F5

Measure

Name Sub Menu Operation Hot-key

Volt Peak to Peak

Maximum Minimum Amplitude Top Base Upper Middle Lower Mean Cycle Mean RMS

Measurement of Peak to Peak Voltage Measurement of Maximum Voltage Measurement of Minimum Voltage Measurement of Amplitude Voltage Measurement of Top Voltage Measurement of Base Voltage Measurement of Upper Voltage Measurement of Middle Voltage Measurement of Lower Voltage Measurement of Mean Voltage Measurement of Cycle Mean Voltage Measurement of RMS Voltage

Ctrl+Alt + P Ctrl+Alt + X Ctrl+Alt + N Ctrl+Alt + A Ctrl+Alt + T Ctrl+Alt + B Ctrl+Alt + U Ctrl+Alt + M Ctrl+Alt + L Ctrl+Alt + E Ctrl+Alt + C Ctrl+Alt + R

Page 42

Chapter 4. Toolbar, Menu & Dialog box

Cycle RMS Positive Overshoot Negative Overshoot

Measurement of Cycle RMS Voltage Measurement of Positive Overshoot Voltage Measurement of Negative Overshoot Voltage

Ctrl+Alt + Y Ctrl+Alt + S Ctrl+Alt + G

Time Period

Frequency Rise Time Fall Time Positive Duty Cycle Negative Duty Cycle Positive Pulse Width Negative Pulse Width

Measurement of Period Measurement of Frequency Measurement of Rise Time Measurement of Fall Time Measurement of Positive Duty Cycle Measurement of Negative Duty Cycle Measurement of Positive Pulse Width Measurement of Negative Pulse Width

Ctrl+Alt + I Ctrl+Alt + F Ctrl+Alt + R Ctrl+Alt + Z Ctrl+Alt + E Ctrl+Alt + D Ctrl+Alt + W Ctrl+Alt + H

Util

Name Sub Name Operation Hot-key

Zero Calibration Begins offset calibration Shift+Ctrl+F6

Help

Name Sub Name Operation Hot-key

Help Shows help file F1 About Displays about Dialog Box F9

Page 43

Chapter 4. Toolbar, Menu & Dialog box

3. Screen Information

SoftScope has the following windows to show the internal states and settings.

: Channel 1 Information window

A. Click on this window, to change the voltage setting. B. The following information is displayed.

a. Volt/Div b. AC/DC coupling c. 1:1/10:1 probe

: Channel 2 Information window

A. Same as channel 1

: Time information window

A. Click on this window to change the time setting. B. The current time/div setting is displayed.

: Trigger point information window

W hen SDS 200 is in a de lay-on state it shows the current trigger point using time

dimension.

W hen SDS 200 is in a delay-off state it shows the current trigger point using %

scale.

: Trigger point display window

The trigger point shows the trigger position in the acquired waveform.

This line shows the whole acquired waveform.

You can see the data currently showing using [ ] mark.

This mark shows the reference point when horizontal scale(time/div) is changed.

Page 44

Chapter 4. Toolbar, Menu & Dialog box

: Trigger state selection tool bar

Trigger source selection radio button

Trigger mode (Auto/Normal)

Trigger condition (Up edge/Down edge)

Triger state display window.

: Trigger state of current acquired waveform

A. 'Auto trig'd' - Trigger signal is automatically generated because of no valid triggered

signal. B. Waiting – SDS 200 is waiting for the incoming trigger. C. Trig'd – Acquired waveform is triggered. D. RIS waiting – SDS is waiting for the incoming trigger in the RIS mode.

Page 45

Chapter 4. Toolbar, Menu & Dialog box

4. Option Dialog Box

Title On -Check to include title on file/print output Title -Use to set the title on file/print output Format -Sets color or Black or white type Include -Check to include informations Grid View -Sets the graticule type Channel Color Level -Sets color level of waveform

-Check to display waveform in color

Page 46

Chapter 5. Appendi x

Ch 5. Appendix

1. Three Operational Modes of SDS 200

Realtime mode

In realtime mode SDS 200 acquires 10,000 sample data from the input source. It can show the real data sim ultaneously. But because of the sampling speed l imit of A/D converter, it is limited only to 10us/div time/div .

RIS(Random Interleaved Sampling) mode

In RIS mode SDS acqu ires wavef orm as well as TDC value, an d rearrange th e waveforms using the TDC value to form one waveform. For example, with firs t acqu isition s am pled dat a f orm s wavef orm A. With s econd acquis itio n sampled forms waveform B. Over and over again waveforms are interpolated to give a complete waveform. SDS 200 has a 200ps time resolution in RIS mode.

Roll mode

To handle low frequency signa ls, SD S 200 has a r oll m ode. In roll m ode ac quir ed waveform is displayed and m oved from the r ight side of the screen to the left. As a resu lt, it appears that the waveform is moving constantly.

SDS 200 operates each mode in the following time scale base:

Time/Div 2ns~4us 10us~400ms 1s~10s

Sampling Mode RIS mode Realtime Mode Roll Mode

2. Software Calibration

It is necessary for you to calibrate regularly to make the measurements as accurate as possible

1. Short input signal as shown below.

Page 47

Chapter 5. Appendi x

2. Select Zero Calibration from menu.

3. Zero calibration dialog box appears.

4. Calibration is done automatically.

Page 48

Chapter 5. Appendi x

3. Firmware Update

You can download new firmware from softDSP website(www.softdsp.com).

1. Connect SDS 200 to PC.

2. Download a new firmware. (.iic file format)

3. Run ezup.exe software.

4. Select File Open.

5. From Dialog Box choose the firmware(.iic) file.

6. Select

, F/W update.

7. Firmware is updated automatically.

softDSP SDS 200 SoftScope User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual