socomec RESYS P40 Operating Instructions Manual

SOCOMEC - Ref.: 541 613 B

RESYS 066 B

INSTALLATION

Installation must only be carried out by qualified per­sonnel.

Before installation, disconnect from the power supply.
Connect the device as shown on the diagram below

(N.B. some optional functions do not need to be cabled).
When installing the device, make the connections

between the relay and the differential toroid as short as
possible.

Do not put relay cables or the differential toroid beside
power conductors.

Do not place differential toroids close to sources of
intense magnetic fields.

>

Note

This differential relay conforms to type A which trips
sinusoidal alternating currents and pulsed currents,
whether they are applied suddenly or change slowly.
This product is also immune to interference.

This relay must be installed in accordance with the
regulations currently in force.

The device must be checked periodically to see that it
complies with the regulations.

>

Test Function

Bargraph blinks

“Trip” LED and “Alarm” relay activated

> Continuous monitoring

Test OK NO NO

Toroid input short circuit NO NO

Relay/Toroid connection break YES NO

> Activation of “Test” button

(Press (>1s) or external button)

Test OK YES YES

Toroid input short circuit NO NO

Relay/Toroid connection break YES NO

>

Pre-alarm function

When the measured current exceeds 50% of the thres­hold value, the pre-alarm relay changes state (if selec­ted in this mode). Automatic reset to its original state if
30% lower than pre-set threshold.

>

Description of front panel

1 - Adjustment/setting I∆n
2 - Green “ON” LED
3 - “RESET” button
4 - Red “TRIP” alarm LED

5 - LED bargraph (% x I∆n)

6 - Configuration DIP switch

(x 4)
7 - “TEST” push-button
8 - Time setting

• With I∆n set at 30 mA, the timing is set at 0 (instanta-

neous) and can not be modified.

• The pre-configured factory setting for the device is 30

mA/0s. These values can be modified as needed for
operation. A plastic seal is provided with the device
in order to lock the protective cover and ensure the
settings.

RESYS P40

EN

Operating instructions

Earth leakage relay
A and AC types

>

Configuration (DIP switch)

Switch Relay configuration

A B AL1 AL2

0 0 Positive security Positive security

1 0 Negative security Pre-alarm (neg. security)

0 1 Negative security* Positive security*

1 1 Negative security Pre-alarm (pos. security)

C Storage mode

1 Automatic reset

0 Storage mode*

D Toroidal transformer ratio

1 600 : 1 > Socomec* toroid

0 1000 : 1 > other manufacturers

* factory configuration

• (negative security: relay excited in case of alarm/positive secu-

rity: relay not excited in case of alarm).

TERMINAL CONNECTION DIAGRAM

L1
L2
L3
N

E

Toroid

50 m* maxi

Alarm 2 (AL2)

or pre-alarm

Alarm 1

(AL1)

678910 11 12

12345

A2

(-)

A1
(+)

reset

test

50 m maxi

The output relays are shown in the non-excited state (for
example, as if the auxiliary supply was not present)

The protective earth wire must not pass through the toroid. For
single-phase applications, only the phase and the neutral must
pass through the toroid.

* Cabling: For distances > 1 m, use a twisted pair for connection
between the relay and the toroid.

>

Troubleshooting

If the product is not working properly, check that is it properly
connected.

DIMENSIONS

4898022

48

32

TECHNICAL SPECIFICATION

• Us Supply (6, 7) :

12 - 125 VDC (85 - 110% de Us)
115, 230 VAC (85 - 115% de Us) (see terminal connection

diagram). All AC supplies are galvanically isolated frm
toroid, TEST and RESET inputs.

• Frequency : 50/ 60Hz (AC supply)

• Isolation : Over-voltage cat. III

• Impulse voltage:

(1,2/ 50µS) IEC 60664
2,5kV (115 VAC supply)
4kV (230 VAC supply)

• Consumption (max.) :

6VA (AC supply) - 5W (DC supply)

• Measured residual current:

0 to 30A (15/ 400Hz) via external toroid with ratio 600:1
or 1000: 1 connected to terminals 4 and 5)

• Sensitivity I∆n :

30, 100, 300, 500 mA, 1, 3, 5, 10, 30 A (adjustable)

• Tripping accuracy: 80 - 90% de I∆n

• Reset value: ≈85% of trip threshold

• Time delay I∆s : 0*, 60, 150, 300, 500, 800ms, 1, 4, 10s

(adjustable) *time set for “0” or “Instantaneous” < 25 ms

for residual current @ 5 x I∆n.

• Reset time:

<2 s (after eliminating the auxiliary power supply)

• Indication des Leds :

- Power supply present:: green

- Bargraph :

3 x green (30, 50 and 70% of the threshold value set)

- Tripping: red

• Operating temperature: -20 to +55°C

• Storage temperature: -30 to +70°C

• Relative humidity: +95%

Outputs

- Number of contacts:: 1 changeover contact relay +
1 single contact relay

- Type of contact :Alarm 1 (8, 9, 10)

AC1 (250 V) 8 A (2000 VA)
AC15 (250 V) 2,5 A
DC1 (25 V) 8 A (200W)
Alarm 2/Pre-alarm (11, 12)
AC1 (250 V) 6 A (1500 VA)
AC15 (250 V) 4 A

DC1 (25 V) 6 A (150W)

- Lifetime: 150.000 operations at nominal load

- Dielectric voltage: 2kV AC (rms) IEC 60947-1

- Impulse voltage: 4kV (1,2/ 50µS) IEC 60664

• Remote Test and Reset (1, 2, 3) :

With N.O. contact (e.g. push-button)Min. contact closure

time: ≥80ms

• Box : black, self-extinguishable, NORYL UL94 VO (front

panel and clip in ABS)

• Weight: 120 g (DC auxiliary power supply)/ 200g (AC

auxiliary power supply)

• Installation: encastré, cut-out 45 x 45mm

• Connecting terminal:

≤ 2,5mm2 flexible

• Certification:

confor ms to IEC 60755, 60947, 61000-4-2, 6100 0-4-3,
61000-4-4, 61000-4-5, 61000-4-6, 61000-4-12, 61000-4­16, 61543.
CE compliant.

>

 References :

Auxiliary power supply Reference
12-125 VDC 4942 3602
115 VAC 4942 3711
230 VAC 4942 3723

>Accessories

Toroids (C.T.) :
∆IC - Ø 15 mm 4950 6015
∆IC - Ø 30 mm 4950 6030
∆IC - Ø 50 mm 4950 6050
∆IC - Ø 80 mm 4950 6080
∆IC - Ø 120 mm 4950 6120
∆IC - Ø 200 mm 4950 6200
∆IC - Ø 300 mm 4950 6300

Use of toroids ≥ 120 mm: setting I∆n min = 300 mA
Other toroids: consult us

CUTOUT

45

45