socomec Netys PE, NETYS PE B600, NETYS PE 600, NETYS PE 800, NETYS PE 1000/LCD Installation And Operating Manual

NETYS PE

600-2000 VA

Installations- und bedienungsanleitung

DE

Manual de instalación y uso

ES

Manuel d’installation et d’utilisation

FR

Installation and operating manual

GB

Manuale di installazione e uso

IT

Installatie– en bedieningshandleiding

NL

Dokumentacja Techniczno-Ruchowa

PL

Manual de instalação e funcionamento

PT

Руководство по установке и эксплуатации

RU

Navodila za priključitev in uporabo

SL

2

NETYS PE - Ref.: IOMNETPEXX03-GB 00

This SOCOMEC UPS uninterruptible power system is guaranteed against manufacturing and material defects, for a period of 24
months from the date of purchase and not however more than 27 months from the date of shipment by SOCOMEC UPS.

The warranty is ‘carry-in’ type: free supply of parts and labour for repairs, with return of a product to be replaced to SOCOMEC
UPS, or authorized centres, at the customer’s cost and risk.

In order to use the warranty service, the user must respect the following rules:

• The product must be returned exclusively in its original packaging. Any damage caused during shipping in packaging other than

the original is not covered by the warranty;

• The product must be accompanied by proof of purchase: a document (bill, invoice, receipt) showing the date of purchase and the
information necessary to identify the product (model, serial number). The number of the authorization for return for repairs must also

be attached, with a detailed description of the defect found in the product. If any of these elements is missing, the warranty is invalid.
The return authorization number is issued by the service centres by telephone on receiving notification of the malfunction;

The warranty is recognised within Italian territory. If the UPS is exported outside Italian territory, the warranty shall

be limited to the cover of the parts used to repair the fault.

The warranty shall not apply in the following cases:

• Failures due to fortuitous circumstances or force majeure (lightning, floods, etc.);

• Failures due to negligence or improper use (use outside tolerance limits: temperature, humidity, ventilation, electric power supply,
applied load, batteries);

• Insufficient or inadequate maintenance;

• Attempted maintenance, repairs or modifications not carried out by SOCOMEC UPS personnel or personnel from a support centre

authorised by SOCOMEC UPS.

• If the battery has not been recharged in accordance with the terms indicated on the packaging and in the manual, in cases of
extended storage or UPS inactivity.

SOCOMEC UPS may, at its own discretion, opt for the repair of the product or for the replacement of the faulty or defective parts

with new parts or with used parts that are equivalent to new parts with regard to functions and performance.

Defective or faulty parts replaced free of charge are to be put at the disposal of SOCOMEC UPS that becomes the sole owner..

Replacements or repairs of parts and any modifications to the product during the warranty period shall not extend the duration of

the warranty.

In no case will SOCOMEC UPS be responsible for damages (including, without limitations, damage for loss of earnings, interruption
of activity, loss of information or other economic losses) deriving from the use of the product.

The present conditions are subject to Italian law. Any dispute falls under the province of the Court of Vicenza.

WARRANTY CERTIFICATE AND CONDITIONS

SOCOMEC UPS retains the full and exclusive ownership rights over this document. Only a personal right to utilize the document for

the application indicated by SOCOMEC UPS is granted to the recipient of such document. All reproduction, modification, dissemi-

nation of this document whether in part or whole and by any manner are expressly prohibited except upon Socomec’s express

prior written consent.

This document is not a specification. SOCOMEC UPS reserves the right to make any changes to data without prior notice.

3

NETYS PE - Ref.: IOMNETPEXX03-GB 00

SUMMARY

ENGLISH

1. SAFETY STANDARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1. Important. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2. Description of the symbols used on the labels applied to the unit. . . . . . . . . . . 4

2. GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.1. Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.2. Environmental requirements for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4. FRONT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5. REAR VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6. CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

7. MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.1. Switching the UPS on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.2. Switching the UPS off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.3. Normal mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.4. Battery mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.5. Overload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

8. COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

8.1. Communication solutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

8.2. USB interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9. REMEDIES FOR MINOR PROBLEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

9.1. Troubleshooting for minor problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

10. TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4

NETYS PE - Ref.: IOMNETPEXX03-GB 00

Important.1.1.

This manual must be kept next to the UPS, so that the operator may consult it at any time for clarification on the correct use of the

UPS. Read the manual carefully before connecting the unit to the mains power supply and to the devices to be powered. Before

switching on the UPS (Uninterruptible Power Supply), the operator must be fully aware of the functions and positions of all the controls
and of the technical and functional characteristics of the system, in order to avoid any risk to persons and to the equipment.

• Before starting, the unit must have an equipotential connection as established by the safety standards in force. The earth cable of

the UPS must be connected to an efficient earth point.

• If the unit is not earthed, all devices connected to the UPS will not have an equipotential connection. In this case the manufacturer

declines all responsibility for damage or accidents caused by non-observance of the aforementioned standards.

• This is a pluggable type A equipment with battery already installed by the supplier, it’s operator installable and may be operated

by layman.

• In case of power failure (UPS in back up mode), do not disconnect the input cable from the mains so as to ensure earth connection

to the powered loads.

• All subsequent maintenance operations must be carried out solely and exclusively by authorized personnel. Inside the system high

electric voltages are generated which may endanger maintenance personnel who are not sufficiently prepared and trained for such
tasks.

• If at any time a hazard condition is created during use, disconnect the mains power supply (if possible through the control panel

upstream of the unit) and shutdown the UPS completely following the appropriate procedure.

• When assembling and replacing the battery, the UPS should always be switched off and disconnected from the mains power

supply. Do not dispose of batteries in a fire, the battery may explode.

CAUTION.
A battery can present a risk of electric shock and high short circuit current.
The following precaution should be observed when working on batteries: remove watches, rings or other metal
objects and use tools with insulated handles.

• The batteries constitute an internal power source for the UPS and mean that the system output may be powered even when the

UPS is not connected to the mains power supply.

• Do not force, break or try to open the batteries. They are sealed and do not require any maintenance. They contain substances

that are toxic to health and that pollute the atmosphere. Do not switch the UPS on if any leakage of liquid or white powder residue

is noted.

• Replace batteries with the same number and type of batteries as originally installed in the equipment.

• Replace the fuses ONLY with other fuses of the same type.

• As the mains cable of the UPS is considered a disconnecting device, the mains socket to which the UPS is connected and/or the

rear of the UPS must be accessible and easy to disconnect.

• Avoid contact of the UPS unit with water or liquids in general. Do not introduce foreign bodies.

• If the unit needs to be scrapped, it must be handed over solely and exclusively to specialist disposal companies. These companies

are obliged to break up and dispose of the various components in accordance with the national legal provisions in force.

• During the installation of this UPS, it should be assured that the sum of the leakage current of UPS and connected loads does not

exceed 3.5 mA

• Netys UPS is intended for commercial and industrial use; it is not recommended for use in medical applications that are essential

to the survival of the patient.

• Use the UPS in accordance with the technical specifications given in the User Manual.

Description of the symbols used on the labels applied to the unit.1.2.

All the precautions and the warnings on the labels and plates on the inside and outside of the equipment should be respected.

DANGER! HIGH VOLTAGE (BLACK/YELLOW)

GROUND TERMINAL

READ THE USER MANUAL BEFORE USING THE UNIT

SAFETY STANDARDS1.

5

NETYS PE - Ref.: IOMNETPEXX03-GB 00

ENGLISH

The main purpose of the UPS is to protect sensitive and critical equipment from electrical disturbances that can compromise opera­tion. Black-outs, brown-outs, variations in voltage and frequency, lightning, electrostatic discharges and rapid over voltages are

phenomena found in all office and industrial environments and which cause damage to the hardware and loss of data.

Netys is an Uninterruptible Power Supply designed to power computers and connected peripherals, with the exception of any other
electrical device (such as household appliances, television sets, stereo systems and video recorders).

Introduction.2.1.

The characteristic feature of these UPS is the constant monitoring of the power supply which, duly filtered and stabilised (on models
with AVR) and if considered suitable, is used to supply consumers. In cases of a mains failure or if the mains is considered to be
outside limits accepted by the load, the inverter (the heart of the UPS) is activated immediately. Drawing on the power stored in
the batteries, the inverter generates a voltage that instantly takes over from the mains without any disruption to the equipment

connected.

During operation under emergency conditions, the internal batteries discharge but are recharged again automatically when mains
power returns.

Being hermetically sealed, the batteries do not require maintenance of any kind at any stage of their working life.

GENERAL DESCRIPTION2.

2.1-1

Block diagram

AVR

Mains input

Output

(to power consumers)

Battery
charger

Battery

Automatic Voltage stabilizer

(AVR models only)

Inverter

(DC/AC)

Automatic

transfer

switch

6

NETYS PE - Ref.: IOMNETPEXX03-GB 00

UNPACKING AND INSTALLATION3.

Unpacking.3.1.

Remove the UPS and all the accessories that come with it (cables, CD-ROMs, etc) from its packing case.

It is always advisable to keep the original packaging that has been specially designed for safe transport, in case the unit has to be
moved again.

Environmental requirements for installation.3.2.

Please check what follows before installing the UPS.

• Netys has been designed for use in closed environments.

• Place the UPS on a flat and stable surface, in a ventilated environment away from heat sources and exposure to direct sunlight.

• Keep ambient temperature between 0 °C and 35 °C and humidity less than 90% (non-condensing); the best temperature to
guarantee the longest battery life is 15-20 °C.

• Ensure that the environment where the UPS will be installed is not dusty, and leave a space of at least 20 cm around it to allow for
adequate ventilation and access to the rear panel.

• Make sure not to place the UPS or any other heavy object on the cables.

• Check that the voltage and frequency preset for operation is right for your electrical power supply looking the data can be found

on the data plate.

• Use only the manufacturer-supplied or recommended cables and accessories for connections to the USB serial interface.

It is recommended to charge the batteries for 8 hours the first time the unit is used.

7

NETYS PE - Ref.: IOMNETPEXX03-GB 00

ENGLISH

FRONT VIEW4.

Operating mode indication.

LED lit: NORMAL MODE (mains OK)•
LED ashing: BATTERY MODE (mains absent or •

abnormal).

Operating mode indication.

LED lit: NORMAL MODE (mains OK)•
LED ashing: BATTERY MODE (mains absent or •

abnormal).

Load present
Load level (5 steps)

Automatic Voltage Regulation active

General Alarm
Battery fault. Replace the battery.

Overload

Acoustic alarm.

Intermittent every 10 seconds: BATTERY MODE.•

Intermittent every second: battery low.•
Intermittent every 0.5 second: overload.•
Intermittent every 2 seconds: battery needs replacing.•
Continuous: UPS failure.•

Acoustic alarm.

Intermittent every 10 seconds: BATTERY MODE.•

Intermittent every second: battery low.•
Intermittent every 0.5 second: overload.•
Intermittent every 2 seconds: battery needs replacing.•
Continuous: UPS failure.•

Red LED.

UPS failure.

ON/OFF switch.

Turns the UPS ON and OFF.

ON/OFF switch.

Turns the UPS ON and OFF.

ON/OFF switch.

Turns the UPS ON and OFF.

NORMAL MODE: Main present

BATTERY MODE: Backup time

(

ashing)

LED bar.

NORMAL MODE: load level (power %) 25% •

steps.

BATTERY MODE: battery level (capacity %) •
25% steps

Battery level:

LIT: battery capacity/battery recharging •
(25% steps).

FLASHING: battery low•

600 VA
800 VA

1000 VA
1400 VA
2000 VA

1000 VA - LCD
1400 VA - LCD
2000 VA - LCD

8

NETYS PE - Ref.: IOMNETPEXX03-GB 00

Telephone/Modem line protections

Output sockets.

Input socket.

Fuse.

USB port.

600 VA

B600 VA

800 VA

REAR VIEW5.

USB port.

Fuse.

Telephone/Modem line
protections

Input socket.

Output sockets.

Fan.

1000 VA
1400 VA
2000 VA

9

NETYS PE - Ref.: IOMNETPEXX03-GB 00

ENGLISH

CONNECTIONS6.

Cables with the appropriate cross-section and conforming to the safety standards in force should be used for
connection to the mains and connection of the loads.

OUT 230 V~

3 x IEC320

IN 230 V~

Use the server’s supply cord (IEC 320)

600 VA

B600 VA

800 VA

IN 230 V~

Use the server’s supply cord (IEC 320)

OUT 230 V~

4 x IEC320

1000 VA
1400 VA
2000 VA

10

NETYS PE - Ref.: IOMNETPEXX03-GB 00

MODES OF OPERATION7.

Switching the UPS on.7.1.

Switch the UPS on by pressing the ON/OFF button on the front panel.

The Normal Mode LED/LCD will light up; allow ten seconds for the self-teach procedures to run.

Switching the UPS off.7.2.

WARNING!
This UPS has been designed to control and maintain the battery charge; therefore only in exceptional circum­stances are you advised to switch it off completely.

To shutdown the UPS completely, press and hold down the ON/OFF button. The UPS switches off all the LEDs/LCD and is then

fully deactivated. If the mains cable is not disconnected, the battery-charger remains active.

Normal mode.7.3.

When mains power is available and the voltage falls within the acceptable range, the Normal Mode LED/LCD indication on the front
panel remains on permanently. The loads are powered from the mains power supply either directly or through the AVR stabiliser
which intervenes in cases of voltage peaks, the batteries are constantly recharged.

Battery mode.7.4.

The UPS switches automatically to this operating mode when mains power fails (spikes or lengthy black-outs) or if the mains is at

a value considered to be dangerous; the consumers are powered using the energy stored in the batteries converted to AC voltage
through the inverter.

In this mode, a slow intermittent acoustic alarm sounds, while the Battery Mode LED/LCD indication on the front panel flashes.

In cases of prolonged mains failure, the UPS powers the consumers until it shuts down when the batteries are fully depleted (see
the chapter “COMMUNICATION” for orderly shutdown via software).

Just before shutdown, when the battery charge runs out fully, low battery charge is signalled via a rapid intermittent acoustic
alarm.

The UPS automatically returns to normal operating mode about two seconds after the mains power is restored. The time taken to
transfer from normal to battery mode and vice-versa is imperceptible to the load.

Overload.7.5.

The UPS can power loads up to the power rating declared on the machine’s data plate; once this limit is exceeded, the machine

goes into overload condition. Overloads are signalled by a rapid sounding acoustic alarm

.

WARNING!
Significant overloads could cause permanent damage to the UPS!
Avoid connecting laser printers that generate absorption peaks liable to cause overloads on the UPS.

11

NETYS PE - Ref.: IOMNETPEXX03-GB 00

ENGLISH

The UPS provides excellent protection against interruptions or imperfections in the mains power supply. In these cases the computer
(load) is powered by the UPS using battery power until this runs out.

Various software applications and communication options are available to optimise operation of the UPS and to correctly manage
shutdown when back-up power ends. The status of the UPS can be monitored, keeping track of all the mains failures and battery

discharges so as to activate an automatic and orderly procedure to close the programs and shutdown the system. When mains

power returns the system will restart automatically.

All Netys models are equipped with USB communication interface (not available on the Netys PE B600 model).

Communication solutions.8.1.

Uni Vision local management software (USB interface) for local shutdown of Windows™ system.

Free on www.socomec.com

USB interface.8.2.

Communication with the server can take place directly via the USB interface.

In addition to local or networked shutdown it is possible to perform full monitoring of the electrical parameters regarding battery
status and the automatic programming of the UPS start-up and shutdown procedures.

For a complete description of the software features, refer to the UniVision documentation.

COMMUNICATION8.

12

NETYS PE - Ref.: IOMNETPEXX03-GB 00

REMEDIES FOR MINOR PROBLEMS9.

Optimal operation of the unit is obtained by keeping it constantly powered (24 hours a day). This guarantees correct maintenance

of the battery charge.

WARNING!
The UPS internally generates hazardous electrical voltages.
All maintenance must be performed solely and exclusively by authorized personnel.

If you have difficulty in getting the UPS to work, the reason may be among those listed below. For any other problem, you are advised
to get in touch with your dealer or service organisation directly.

For quick and effective action, when you call it is important to give precise details of the defect, the model number and the manu­facturing serial number that can be found on the conformance and inspection certificate or on the data plate on the bottom of the
UPS.

Troubleshooting for minor problems9.1.

Problem Possible cause Solution

The UPS works in battery mode even if mains
power is available.

Poor connection to the input mains.

Check the connection of the cable to
the UPS and to the mains outlet.

The mains voltage is out of range.

No solution because mode of opera­tion is correct.

Input protection triggered (blown
fuse or automatic switch).

Replace the input fuse with another
of the same type or reset the auto­matic switch.

Back-up time shorter than expected.

Batteries not fully charged.

Leave the batteries to charge for 8
hours consecutively

Batteries not working properly.

Have the batteries replaced by
authorised personnel.

The UPS stalls/goes into overload Overload on the load line.

Check that the load applied is not

greater than the maximum permitted
or reduce the load power require-

ment.

if the equipment is to be left idle for a long period, wait for the batteries to charge fully before switching off. While
the ups is left idle, make sure that the batteries are recharged for 24 hours at least once every 4 weeks.

13

NETYS PE - Ref.: IOMNETPEXX03-GB 00

ENGLISH

TECHNICAL SPECIFICATIONS10.

Models

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Power (VA) 600 600 800 1000 1400 2000

Power (W) 360 360 480 600 840 1200

Technology Line Interactive Step Wave with AVR voltage stabilizer

Electrical specifications - Input

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Mains voltage 170 - 270 V

Frequency (nominal) 50/60 Hz with automatic selection

Mains connection IEC320 socket

Reporting and Communication

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Communication interface

- USB

Local communication software -

UniVision (management software)

Telephone protection -

Telephone line/modem/ADSL suppressor: RJ11

Battery

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Typical back-up time

(PC+15” LCD monitor)

15 min 15 min 20 min 45 min 55 min 60 min

Battery recharge Under permanent charge even when the UPS is off (mains present)

Mechanical characteristics

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Dimensions (WxDxH mm) 99x334x143 99x334x143 99x334x143 145x405x205 145x405x205 145x405x205

Net weight (kg) 6.0 6.1 6.6 9.7 10.5 10.6

Electrical specifications - Output

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Automatic Voltage Regulation (AVR) • • • • • •

Voltage (in Battery Mode) 230 V ±10%

Frequency 50/60 Hz

Wave form Stepwave

Protection Overload, deep discharge and short circuit

Load connection socket IEC320 3 (C13) 3 (C13) 3 (C13) 4 (C13) 4 (C13) 4 (C13)

Environment

PE B600 PE 600 PE 800 PE 1000/LCD PE 1400/LCD PE 2000/LCD

Noise level at 1 meter <45 dBA

Voltage (in Battery Mode) 0÷35 °C (15÷25 °C for optimum battery life)

Environment Altitude: 2000 m, humidity: 90% non-condensing

Reference standards EN62040-1-1 (safety), EN62040-2 (EMC)

Non contractual document. © 2010, Socomec SA. All rights reserved.

HEAD OFFICE

SOCOMEC GROUP

S.A. SOCOMEC capital 11 102 300 € - R.C.S. Strasbourg B 548 500 149
B.P. 60010 - 1, rue de Westhouse - F-67235 Benfeld Cedex

SOCOMEC UPS Strasbourg

11, route de Strasbourg - B.P. 10050 - F-67235 Huttenheim Cedex- FRANCE
Tel. [phone] - Fax [phone]
[e-mail]

SOCOMEC UPS Isola Vicentina

Via Sila, 1/3 - I - 36033 Isola Vicentina (VI) - ITALY
Tel. [phone] - Fax [phone]
[e-mail]

S A L E S , M A R K E T I N G A N D

SERVICE MANAGEMENT

SOCOMEC UPS Paris

95, rue Pierre Grange
F-94132 Fontenay-sous-Bois Cedex - FRANCE
Tel. [phone] - Fax [phone]
[e-mail]

Socomec UPS

worldwide

IN EUROPE

BELGIUM

Tel. [phone]
Fax [phone]
[e-mail]

FRANCE

Tel. [phone]
Fax [phone]
[e-mail]

GERMANY

Tel. [phone]
Fax [phone]
[e-mail]

ITALY

Tel. [phone]
Fax [phone]
[e-mail]

NETHERLANDS

Tel. [phone]
Fax [phone]
[e-mail]

POLAND

Tel. [phone]
Fax [phone]
[e-mail]

PORTUGAL

Tel. [phone]
Fax [phone]
[e-mail]

RUSSIA

Tel. [phone]
Fax [phone]
[e-mail]

SLOVENIA

Tel. [phone]
Fax [phone]
[e-mail]

SPAIN

Tel. [phone]
Fax [phone]
[e-mail]

UNITED KINGDOM

Tel. [phone]
Fax [phone]
[e-mail]

IN ASIA

CHINA

Tel. [phone]
Fax [phone]
[e-mail]

INDIA

Tel. [phone]
Fax [phone] — 51
[e-mail]

MALAYSIA

Tel. [phone]
Fax [phone]
[e-mail]

SINGAPORE

Tel. [phone]
Fax [phone]
[e-mail]

THAILAND

Tel. [phone]
Fax. [phone]
[e-mail]

VIETNAM

Tel. [phone]
Fax [phone]
[e-mail]

IN OCEANIA

AUSTRALIA

Tel. [phone]
Fax [phone]
[e-mail]

www.socomec.com

YLATI ROF DILAVECNARF ROF DILAV

ISO 9001:2008

FM 28237

ISO14001:2004

EMS 553476

*IOMNETPEXX03-GB 00*

IOMNETPEXX03-GB 00 02.2010