Gateways
EN
www.socomec.com
0 | |
---|---|
2. DANGER AND WARNING | 4 |
2.1. Risk of electrocution, burns or explosion | 4 |
2.2. Risk of damaging the unit | 4 |
2.3. Liability | 4 |
3 PREI IMINABY OPERATIONS | 5 |
~ | |
6 | |
6 | |
6 | |
4.1.2. Functions | 1 |
1 | |
8 | |
8 | |
4.2.2. Dimensions | 8 |
5. ASSEMBLY | 9 |
5.1. Recommendations and safety | 9 |
5.2. Fitting the battery | 9 |
5.3. DIRIS G mounting | 9 |
5.3.1. DIN-rail mounting | 9 |
5.3.2. Plate mounting | 0 |
5.4. Optional modules mounting1 | 0 |
5.4.1. Monting an optional module on the gateway | 0 |
5.4.2. Mounting an optional module on an optional module 1 | 0 |
6. CONNECTION | 1 |
6.1. DIRIS G connection | 1 |
6.2. Optional modules connection 1 | 3 |
7. STATUS AND AUTO-ADDRESSING LEDS | 4 |
7.1. Status I FDs | 4 |
7.2. Auto-addressing | 5 |
ē | |
9.1 Concret information | 0 |
6 | |
9.0 DS495 rules 1 | 6 |
8.2. RS485 rules |
6
7 |
8.2. RS485 rules |
6
7 8 |
8.2. RS485 rules |
6
7 8 8 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi actoway communication 1 |
6
7 8 9 |
|
6
7 8 9 9 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication. 1 8.5. Communication tables 1 |
6
7 8 9 9 9 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 |
6
7 8 9 9 9 0 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 |
6
7 8 9 9 9 0 0 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication. 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 |
6
7 8 9 9 9 0 0 0 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication. 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 |
6
7 8 8 9 9 9 0 0 0 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.4. Multi-gateway communication of Conformity 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 |
6
7 8 8 9 9 9 0 0 0 1 2 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 |
6
7 8 8 9 9 9 0 0 0 1 2 2 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 10.1.1. Mechanical characteristics 2 | 67889990001222 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1.1 DIRIS G characteristics 2 10.1.2. Electrical characteristics 2 10.1.2. Electrical characteristics 2 | 678899900012222 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10.1. DIRIS G characteristics 2 10.1.1. Mechanical characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 | 678899900012222 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 10.1.2. Electrical characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 10.1.4. Communication specifications 2 | 67889990001222222 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10.1.1. DIRIS G characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 10.1.4. Communication specifications. 2 10.1.5. Memory characteristics | 67889990001222223 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication. 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 10.1.2. Electrical characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 10.1.4. Communication specifications 2 10.1.5. Memory characteristics 2 10.1.6. Environmental specifications 2 | 678899900012222233 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication. 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 10.1.2. Electrical characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 10.1.4. Communication specifications. 2 10.1.5. Memory characteristics 2 10.1.6. Environmental specifications 2 10.1.7. Electromagnetic compatibility 2 | 6788999000122222333 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 10.1.1. Mechanical characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 10.1.4. Communication specifications 2 10.1.5. Memory characteristics 2 10.1.6. Environmental specifications 2 10.1.7. Electromagnetic compatibility 2 10.1.8. Safety 2 | 678899900012222223334 |
8.2. RS485 rules 1 8.3. Radio-frequency (RF) rules. 1 8.3.1. Setting up 1 8.3.2. EC Declaration of Conformity 1 8.4. Multi-gateway communication. 1 8.5. Communication tables 1 9. CONFIGURATION 2 9.1. Configuration using Easy Config 2 9.1.1. Connection modes 2 9.1.2. Time setting 2 9.1.2. Time setting 2 10. CHARACTERISTICS 2 10.1. DIRIS G characteristics 2 10.1.2. Electrical characteristics 2 10.1.3. Input characteristics 2 10.1.4. Communication specifications 2 10.1.5. Memory characteristics 2 10.1.6. Environmental specifications 2 10.1.7. Electromagnetic compatibility 2 10.1.8. Safety 2 10.1.9. Service life 2 | 6788999000122222233344 |
All documentation concerning the DIRIS G-30, G-40, G-50 and G-60 gateways is available at the SOCOMEC website at the following address:
www.socomec.com/en/diris-g
DIRIS G - 542 872 B - SOCOMEC
The term "unit" used in the following paragraphs encompasses all of the DIRIS G-30, G-40, G-50 and G-60 gateways.
The assembly, use, servicing and maintenance of this equipment must only be carried out by trained, qualified professionals.
SOCOMEC shall not be held responsible for failure to comply with the instructions in this manual.
4 | Caution: risk of electric shock | Ref. ISO 7000-0434B (2004-01) |
---|---|---|
Caution: Refer to the accompanying documentation each time this symbol is shown | Ref. ISO 7000-0434B (2004-01) |
Failure to take these precautions could cause death or serious injuries.
4 | Caution: risk of electric shock | Ref. ISO 7000-0434B (2004-01) |
---|---|---|
Caution: Refer to the accompanying documentation each time this symbol is shown | Ref. ISO 7000-0434B (2004-01) |
To ensure that the unit operates correctly, make sure that:
Failure to respect these precautions could cause damage to the unit.
To ensure the safety of personnel and the unit, please carefully read the contents of these user manual before installation.
Check the following points as soon as you receive the package containing the unit:
The DIRIS G-30, G-40, G-50 and G-60 are communication gateways with a modular format which act as an interface between products (PMD*, meters, etc.) equipped with an RS485 communication bus using the Modbus protocol, DIRIS B-30 using radio communication (DIRIS G-40 and G-60 only) and the Ethernet network. On the Ethernet network, the gateways use the Modbus TCP protocol to enable data to be exchange and centralised between the meters, the PMDs and monitoring software. In addition, the WEBVIEW web server embedded in the gateways can be used for monitoring of electrical values in real-time (Power Monitoring version) and reporting of energy data (Power & Energy Monitoring version).
*PMD: Performance Measuring and monitoring Device in accordance with IEC 61557-12.
Gateway | DIRIS G-30 | DIRIS G-40 | DIRIS G-50 | DIRIS G-60 |
RS485 communication | ٠ | • | • | • |
RF communication | • | • | ||
WEBVIEW Webserver
Power Monitoring Monitoring: real-time measurements and alarms. |
٠ | • | ||
WebServer WEBVIEW
Power & Energy Monitoring Monitoring: real-time measurements and alarms. Visualisation: measurement and consumption datalogger. |
• | • | ||
Ref. 4829 0300 | Ref. 4829 0301 | Ref. 4829 0302 | Ref. 4829 0303 |
Remote antenna RF 868MHz
Height: 210mm |
Cable for remote antenna.
SMA connector. Length: 3m |
USB cable for configuration |
---|---|---|
Ref. 4854 0126 | Ref. 4854 0127 | Ref. 4829 0050 |
Depending on the reference, the DIRIS G-30, G-40, G-50 and G-60 perform a range of functions, including:
The optional modules, which have a modular format, are fitted on the DIRIS G; they are used to extend its functionalities in terms of inputs/outputs and communication modes.
DIRIS O-iod | DIRIS O-ioa | DIRIS O-it |
---|---|---|
2 digital inputs/outputs module | 2 analogue inputs/outputs module | 3 temperature inputs module |
Ref. 4829 0030 | Ref. 4829 0031 | Ref. 4829 0032 |
DIRIS O-iod | DIRIS O-ioa | DIRIS O-it | |
---|---|---|---|
Α | 1.77in / 45mm |
The following paragraphs describe the installation of the DIRIS G-30, G-40, G-50 and G-60 gateways and the optional modules.
Refer to the safety instructions (section "2. Danger and warning", page 4)
Environment: This product contains a 3V CR1220 lithium button battery. Because of the potential health and environmental effects of the substances used in batteries, do not dispose of them with household waste.
The battery is supplied in a separate bag.
To insert the battery, first power off the unit and wait for 1 minute before using a finger to slide off the cover on the top of the gateway. Insert the battery, observing the polarity. Close the cover.
5.3.1. DIN-rail mounting
5.4.1. Monting an optional module on the gateway
5.4.2. Mounting an optional module on an optional module
The following guidelines for installation must be observed:
Power
Input powered by the product Input with external power supply
RS485
Power supply of optional modules
*0.5 A gG / BS 88 2A gG / 0.5 A class CC fus
LEDs are used to view the status of the product.
The addressing button are used to automatically assign a Modbus® address from the gateway to all the products in its RS485 or RF network.
LED status | Fixed | Blinking | Pulse |
---|---|---|---|
ON | In operation |
10 seconds - On request via a
Modbus control to identify the device (remote screen,) |
1 second to start-up |
ALARM | An alarm (logic/analogue) is active | - | 1 second to start-up |
RS COM | In the addressing phase | In the scan phase | 1 second to start-up and when a frame received is processed |
COM RF | In the addressing phase | In the scan phase | 1 second to start-up and when a frame received is processed |
ETH | Initialisation problem | - |
1 second to start-up and in
Modbus TCP communication |
MEMORY | Full or write problem | - | 1 second to start-up and during a write to the memory |
Note: The "ON" / "ALARM" / "RS COM" LEDs flash if an error within the product is detected.
Auto-addressing mode is used to automatically allocate addresses to products connected to the gateway. This mode is only compatible with DIRIS G-30 and Digiware type PMDs. The addresses will be allocated manually on the other PMD (DIRIS A) and meters (COUNTIS).
Three modes are available:
Mode 1 is without external equipment (see description below).
Modes 2 and 3 are carried out from a PC equipped with Easy Config. These 2 modes are described in the Easy Config manual.
Note: During the auto-addressing process, the RS485 line is reserved for allocating addresses and no other exchange of data is possible at this time
Depending on its reference, the gateway communicates using RS485 or RS485/RF. With a RS485 link, the products are connected in series to the gateway (DIRIS G-30, G-40, G-50 and G-60). With a radio-frequency link, the DIRIS B-30 communicate with the gateway in the RS485/RF version (DIRIS G-40 and G-60).
The table below shows the communication modes available on each of the gateways.
Gateway | DIRIS G-30 | DIRIS G-40 | DIRIS G-50 | DIRIS G-60 | |
---|---|---|---|---|---|
Communication | RS485 | • | • | • | • |
Radio-frequency | ٠ | ٠ | |||
Ref. 4829 0300 | Ref. 4829 0301 | Ref. 4829 0302 | Ref. 4829 0303 |
Example of an installation integrating a DIRIS G-40 or G-60 gateway with DIRIS B-30 RF and RS485 multifunction meters:
The DIRIS G-30, G-40, G-50 & G-60 gateways communicate via the Modbus protocol with the products connected to them. The DIRIS B which integrate radio communication are seen as Modbus slaves.
The Modbus protocol requires a dialogue with a master/slave structure. The mode of communication is the RTU (Remote Terminal Unit).
The gateway integrates the following parameters:
The gateway transmits the data collected using the Modbus TCP protocol via the Ethernet communication port. The default IP address is:
16 EN
RS485 communication is available on all the gateways. It takes place via an RS485 serial link (2- or 3-wire) in accordance with the Modbus RTU protocol. It is used to collect all the data coming from the connected products (meters, multifunction meters, etc.).
In a standard configuration, an RS485 link enables the interconnection of 32 products to a PC, a PLC or the gateway over a distance of 1200 metres.
Example of connecting an RS485 link with the gateway:
A LIYCY type connecting cable with a shielded twisted pair is required. In a disturbed environment or large network (in terms of length or number of products) the use of a type LIYCY-CY twisted pair with general shielding is recommended.
A 120-ohm resistor must be placed at both ends of the link.
A 120-ohm resistor is supplied with each DIRIS G gateway.
Comment: class B in radiated power is obtained using ferrites (ref. 4829 0048) with the following number of rounds:
Wireless radio-frequency communication on the 868 MHz bandwidth is available on the DIRIS G-40 and G-60 gateways for communicating with the DIRIS B-30 in RF version (ref. 4829 0002).
These gateways collect data from the wireless DIRIS B-30 and also from the DIRIS B-30 or other products (COUNTIS, DIRIS...) with a RS485 link. This data can then be transferred to a PC via an Ethernet link with Modbus TCP protocol.
The DIRIS B-30 RF are particularly useful for using loads located in isolated, remote areas, without the need to set up a cabled communication link.
Example of an installation integrating DIRIS B-30 RF with a DIRIS G-40 or G-60 gateway:
Only use antennae recommended by SOCOMEC.
The wireless gateway communicates over a distance of 300 metres in open-field conditions.
The permitted occupancy rate depends on the frequency used. The frequency is selected using the Easy Config configuration tool.
The table below describes the permitted occupancy rate based on the selected frequency and the resulting maximum number of DIRIS B-30 which can be connected.
Channel no. | Frequency (MHz) | Permitted occupancy rate |
Maximum number of
DIRIS B-30 connected |
---|---|---|---|
420 | 868.1000 | 1% | 16 |
436 | 868.3000 | 1% | 16 |
452 | 868.5000 | 1% | 16 |
472 | 868.7500 | 0,10% | 3 |
488 | 868.9500 | 0,10% | 3 |
504 | 869.1500 | 0,10% | 3 |
534* | 869.5250 | 10% | 32 |
539 | 869.5875 | 10% | 32 |
According to EN300 220: radiated radio and REC7003 emissions: use of the RF 868 MHz bandwidth. *Default channel.
Note: in order to observe a frequency spacing of 200 kHz, channels 534 and 539 cannot be used at the same time.
The EC Declaration of Conformity for the DIRIS G is available here: www.socomec.com/en/diris-g
In this configuration, a slave RF gateway communicates with the master RF gateway.
The communication tables and the associated explanations are available on the documentation page for the DIRIS G-30, G-40, G-50 and G-60 on the website SOCOMEC at the following address:
www.socomec.com/en/diris-g
The gateway is configured via the Easy Config configuration software using Ethernet or USB. Easy Config must be installed before using the USB connection.
The Easy Config software is also used to configure the SOCOMEC products via Ethernet or USB via the gateway without having to individually connect to each of the products.
From Easy Config, time setting is achieved from an SNTP server or manually. The time may be displayed on connected products automatically based on a configurable update schedule.
Dirki 5 0-30/0-40/
e-50/0-40 |
mail Aurros I/O Final Action | EASY CONFIG TOOL V2.2 |
---|---|---|
SNTP server settings | ń - | |
Activation | Yes | - O |
SNTP server IP address | 0.0.0 | 0 |
SNTP Server Port | 123 | 0 |
Slave Time Diffusion | ||
Automatic slaves time update | Yes | • 0 |
Gateway time update frequency | 60 🔤 s | Ø |
Slaves time update frequency | 30 🚉 s | 0 |
Slaves Information Diffusion | ||
Slaves load curve synchronisation method | Disabled | •0 |
Slaves load curve integration time | 15 Min | 0 |
Slaves historical values synchronisation metho | Disabled | • 0 |
Slaves historical values integration time. | 60 🔤 Min | 0 |
O Date/Time | ||
Time Zone | (urc | •00 |
Send Date/Time to device |
Automatic : Sync from PC Data/Time
Manual : S/15/2014 3064128 PM S Send |
- |
socomec |
So that all connected products display the same time, use the DIRIS G gateway or the multipoint DIRIS Digiware D-50 screen for synchronisation.
Do not use the synchronisation function on a monopoint DIRIS D-30 screen as part of a multiproduct configuration.
Casing type | DIN-rail mounting module and base |
---|---|
Casing protection index | IP20 / IK06 |
Index of protection of front side | IP40 on the nose in modular assembly / IK08 |
Weight |
DIRIS G-30, G-50 = 190 g
DIRIS G-40, G-60 = 215 g |
Power supply | |
---|---|
Alternative voltage | 110-230 VAC ±15% (Ph/N or Ph/Ph) Cat III |
Frequency | 50/60 Hz |
Consumption | 6VA |
Battery | CR 1220 3 V lithium button cell battery |
Connection | Removable spring-cage terminal block, 2x 2 positions, 0.5 2.5 mm 2 solid cable or 0.25 1.5 mm 2 stranded cable with end piece |
Input | |
---|---|
Number | 1 |
Type / Power supply | Optocoupler internal (12VDC ± 10%) or external (10-30VDC± 10%) polarisation |
Input function | Logic status, pulse meter or synchronization pulse status |
Connection | Removable screw terminal block, 2 positions, stranded or solid 0.14 1.5 mm 2 cable |
DIRIS G | |
---|---|
Connection | RS485 |
Connection type | 2 3 half duplex wires |
Protocol | Modbus RTU |
Data rate | 2400 115200 bauds |
Function | Communication with PMDs and meters |
Connection | Removable screw terminal block, 2 positions, stranded or solid 0.14 1.5 mm 2 cable |
DIRIS G-40 and DIRIS G-60 | |
Connection | Radio-frequency (RF) |
Frequency range | 868 MHz (low frequency: 868.1 MHz and high: 869.5875 MHz) |
Speed | 38400 bauds |
Function | Communication with DIRIS B-30 RF |
Range | 300m in free field |
Ethernet |
Connection | Ethernet 10/100 base-T 2 RJ45 bases with integrated switch |
---|---|
Protocol | Modbus TCP (port 502), Modbus RTU over TCP (port 503), HTTP, SMTP, SNTP, DHCP |
Clock | Internal |
SNTP Protocol |
Allows updating of the gateway from an NTP server.
The gateway updates the connected PMD. |
SMTP Protocol | Allows alarm email to be sent from the gateway |
Function |
Configuration of the gateway, PMDs and connected meters
Access to the WEBVIEW web server, centralization of data for a supervisor |
Connection | RJ45 connector - Straight-through or crossover cable |
USB | |
Connection type | USB 2 (required installation of Easy Config) |
Protocol | Modbus RTU on USB |
Function | Configuration of the gateway, PMDs and connected meters |
Connection | Type B micro USB connector |
Consumption history (memory extension for meters and measurement units) | 1 year (1 hour period) |
---|---|
Electrical values | 2 months (10 min period) |
Number of events |
Alarms: 1000
Network quality according to EN 50160: 1000 |
Ambient service temperature | -10 +70°C (IEC 60068-2-1/IEC 60068-2-2) |
---|---|
Storage temperature | -25 +85°C (IEC 60068-2-1/IEC 60068-2-2) |
Operating humidity | 55°C / 97% RH (IEC 60068-2-30) |
Operating altitude | < 2000 m |
Vibration | 1G of 10Hz to 100Hz |
Rated impulse voltage | IEC 60947-1 V. IMP : 6.4kV |
PEP ecopassport - ISO 14025 | DIRIS G: SOCO-2014-02-v1-fr, SOCO-2014-02-v1-en |
Immunity to electrostatic discharges | IEC 61000-4-2 LEVEL III |
---|---|
Immunity to radiated radio-frequency fields | IEC 61000-4-3 LEVEL III |
Immunity to electrical fast transients/bursts | IEC 61000-4-4 LEVEL IV |
Immunity to impulse waves | IEC 61000-4-5 LEVEL IV |
Immunity to conducted disturbances | IEC 61000-4-6 LEVEL III |
Immunity to power frequency magnetic fields | IEC 61000-4-8 400A/m LEVEL IVt |
Conducted emissions | CISPR 11 Group1 - CLASS B |
Radiated emissions | CISPR11 Gr :1 - CLASS B (with external ferrites - ref. 4829 0048) |
Immunity to voltage dips and short interruptions | IEC 61000-4-11 LEVEL III |
Safety | Compliance with Low Voltage Directive 2006/95/EC of 12th December 2006 (EN 61010-1:2010) |
---|---|
Insulation | Installation category III (300VAC Ph/N), degree of pollution 2 |
MTTF (mean time to failure) | > 100 years |
---|---|
Mechanical characteristics | |
---|---|
Casing type | Modular for DIN rail mounting |
Power supply (1) | |
Alternative voltage | 110-230 VAC ±15 % |
Frequency | 50/60 Hz |
Connection | Removable spring-cage terminal block, 2x 2 positions, 0.5 2.5 mm 2 solid cable or 0.25 1.5 mm 2 stranded cable with end piece |
(1) No power supply to DIRIS O-it. | |
DIRIS O-iod - 2 digital inputs/2 digital outp | outs |
Number of inputs | 2 per optional module - 4 optional modules max. |
Туре | Optocoupler internal (12VDC ± 10%) or external (10-30VDC± 10%) polarisation |
Function | Logic status or pulse meter |
Input connection | Removable screw terminal block, 4 positions, stranded or solid 0.14 1.5 mm 2 cable |
Number of outputs | 2 per optional module - 4 optional modules max. |
Туре | Relay / 230V ±15 % - 1A |
Function | Configurable alarm (current, power,) on threshold overruns or remote controlled status |
Output connections | 2 removable screw terminal blocks, 2 x 2 positions, stranded or solid 0.14 1.5 mm 2 cable |
DIRIS O-ioa - 2 analogue inputs/2 analogu | le outputs |
Number of inputs | 2 per optional module - 4 optional modules max. |
Туре | 4-20 mA |
Function | Connection of analogue sensors (pressure, humidity, temperature, etc.) |
Input connections | Removable screw terminal block, 4 positions, stranded or solid 0.14 1.5 mm 2 cable |
Number of outputs | 2 per optional module - 4 optional modules max. |
Туре | 4-20 mA |
Function | Transmission of an image of the measurements (power, currents, etc.) to automated machines. |
Output connection | Removable screw terminal block, stranded or solid 0.14 1.5 mm 2 cable |
DIRIS O-it - 3 temperature inputs | |
Number of inputs |
3 external inputs + 1 ambient measurement
Max 1 optional module |
Dynamic | -20 °C to 150 °C |
Туре | PT100 or PT1000 |
Function of inputs 1, 2 and 3 | Temperature measurement. |
Connection | 3 removable screw terminal blocks, 4 x 2 positions, stranded or solid 0.14 1.5 mm 2 cable |
24 EN
DIRIS G - 542 872 B - SOCOMEC