Socket & See SP200, SP400, VP400 Instruction Manual & Specification

Instruction Manual & Specification

SP200, SP400

& VP400

Proving Units

SS0019V2

Sn

VP400 SP200 SP400

2

SS0019V2

1. Safety

1.1 Equipment Markings

1.2 Operational Safety

Warning - Risk of Electric Shock !
The proving unit generates up to 690V.

The Socket and See SP200, SP400 and VP400 proving units are designed to be
used by skilled persons in accordance with safe methods of work. If the proving
unit is used in a manner not specified by Socket and See, the protection
provided by it may be impaired.

Inspect the proving unit before using. If any damage is visible such as cracks in
the casing the unit should not be used.

Before use ensure the proving unit is free from moisture, grease and dust. If the
unit requires cleaning use a soft dry cloth only.

Caution - refer to the instruction manual

Construction is double insulated

Product should be recycled as electronic waste

Conforms to EU standards

3

SS0019V2

2. Description

The UK designed SP200, SP400 and VP400 Proving Units provide a safe and
reliable means of checking the correct operation of Multimeters and two pole
voltage Indicators (VI).

The SP200 and SP400 are powered by 6 x AA alkaline batteries whereas the
VP400 is designed to be permanently mounted in a vehicle and operated from
its 12V supply.

2.1 Features

● Intelligent voltage ramp for testing multimeters and VI’s.

● Generates outputs from 50 - 690V with a true AC waveform at 50Hz. This

means it will always read correctly using the AC range of your tester or
multimeter.

● The SP400 and VP400 proving units both have a non-contact voltage
detector facility.

● Powerful enough to light old filament style lamps.

● Automatic operation and turn-off for ease of use and battery conservation.

2.2 Indication

The voltage ramp indication on all proving units is displayed clearly using red
LEDs.

The SP400 and VP400 indicate at 50-110-230-400 V

The SP200 indicates at 50-100-230-400-690 V

All proving units have a blue LED
Power indicator that will flash to
indicate when batteries need to
be changed.

SP400 Proving a Socket and See

VIP ESI Voltage Indicator

4

SS0019V2

3. Usage

3.1 Battery Installation and Status

The SP200 and SP400 use 6 x LR6 AA alkaline batteries.

Do Not use rechargeable batteries.

The batteries are accessible by removing two screws on the rear of the units
case.

Ensure all testers are disconnected before accessing batteries.

Do not mix old and new batteries.

For maximum life use only good quality batteries.

Dispose of batteries as required by local regulations.

The Blue power LED will flash when in operation if the batteries need to be
changed.

The VP400 is designed to the hard wired into the 12V supply of a vehicle. The
supply should be taken from a fused outlet. RED (12V) and BLACK (0v). An extra
Isolating circuit within the proving unit maintains safety even in single fault
conditions.

3.2 Operation

Red voltage indication

LEDs.(SP200 Includes a

690V LED.)

Non contact voltage

tester push button.

(Not applicable on

SP200).

Non contact

voltage detector

test area. (Not

applicable on

SP200)

Voltage

indicator test

points.

Blue power indication

LED. (Flashes when

battery needs

changing).

Unit shown SP400

5

SS0019V2

3.3 How to Use

1) Prove your voltage indicator (VI) is working by placing a probe in each test
point. Contact the bottom with the right hand probe then apply gentle
downward pressure on the left hand probe. This will activate a micro switch,
the blue power LED will illuminate and the proving unit will launch into Auto
Prove Mode.

2) The Proving Unit will automatically step up to 690V. (On the SP400 and
VP400 the 400V LED is used to indicate all voltages greater than 400V). The
unit then steps the voltage back down, (690V - 400V - 230V - 100V - 50V ­OFF). To reprove the VI again, simply raise and then depress the left hand
probe and the Auto Prove Mode will cycle again.

Advantages of the Auto Prove Mode

● Individual voltages are applied at key voltage test points.

● If the two pole VI draws a high current from the proving unit the Auto Prove

mode will pause. This is useful if testing certain types of two pole voltage
testers, including those with filament lamps.

● Significant battery savings as the power is automatically switched off when
the proving test is complete.

● After completion of the auto prove there is a closed circuit between the
voltage indicator test points. This means that if your VI has a continuity tester
it will prove its operation and sound to confirm completion of the process.

3) Having established that your VI is working correctly carry out the testing
required. If you are in doubt at any time use the proving unit to reprove the
correct functioning of the VI.

4) Having completed your testing with the VI use the proving unit to ensure
that it is still functioning correctly.

5) In addition to two pole VI proving the SP400 and VP400 can test non
contact voltage detectors (NCVD). To do this depress the Volt Detector Test
button and the red indication LED's and blue power LED should illuminate,
as the button is being pressed apply the tip on the NCVD to the Volt Tip
Area . Check for correct operation of the NCVD.

6

SS0019V2

4. Maintenance and Service

If required, clean with a soft, dry cloth. Do not use abrasives or solvents.

SP200 & SP400. The only user replaceable parts are the 6 x AA alkaline batteries.

VP400. There are no user serviceable parts.

Contact Socket and See for parts and technical assistance.

Socket and See
Century Road
High Carr Business Park
Newcastle
Staffordshire, UK
ST5 7UG

Tel: [phone]
Fax: [phone]

Email: [e-mail]
Website: www.socketandsee.co.uk

7

SS0019V2

Specification

Output Voltage

50 - 690V in five steps
(50V,100V,230V,400V,690V)

Safety Compliance

BS EN 61010-1:2010

EMC Compliance

61326-1:2006

Operating Conditions

-10 to +35°C at 95% RH

Output Frequency

50Hz Pseudo sine wave

Maximum Output power

10W

Batteries

(SP200 & SP400) 6 x LR6 AA alkaline
batteries

(VP400) Hard wired into vehicle 12V
supply

Battery Life

(SP200 & SP400)10 hours with average
use when testing high and low power
testers.

(VP400) N/A

Dimensions

68H x 130W x 48D (mm)

Weight

(SP200 & SP400) with batteries 350g

(VP400) 200g

Ordering Information

Item Supplier Code

Socket and See SP200 SOC/SP200

Socket and See SP400 SOC/SP400

Socket and See VP400 SOC/VP400

SS0019V2