www.socketmobile.com
Bluetooth
®
wireless technology
Cordless Barcode Scanner
ATTACHABLE
SOCKETSCAN™ 800 SERIES USERGUIDE
socketmobile.com
Package Contents 3
Product Information 4
Charge the Battery 5
Optional Charging Accessories 6
Scanning Barcodes 7
Bluetooth Connection Modes 8-9
Setup without software application (Basic Mode):
• Android 10
• Apple® 11
• Windows 12
Setup using Application Mode:
• Android 13-14
• Windows 15-16
• Apple 17-18
Active Mode 20-21
Bluetooth Unpairing 21
Factory Reset 22
Restore Method 23
Status Indicators 24-25
Product Specications 26-28
Helpful Resources 29
Regulatory Compliance 30-31
Limited Warranty 32
Command Barcodes 33-35
PACKAGE CONTENTS
PACKAGE CONTENTS
Thank you for choosing Socket Mobile!
Let’s get started!
PACKAGE CONTENTS
© 2017 Socket Mobile, Inc. All rights reserved. Socket®, the Socket Mobile logo, SocketScan™,
DuraScan™, Battery Friendly® are registered trademarks or trademarks of Socket Mobile, Inc.
Microsoft® is a registered trademark of Microsoft Corporation in the United States and other
countries. Apple®, iPad®, iPad Mini®, iPhone®, iPod Touch®, and Mac iOS® are registered
trademarks of Apple, Inc., registered in the U.S. and other countries. The Bluetooth® Technology word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and
any use of such marks by Socket Mobile, Inc. is under license. Other trademarks and trade
names are those of their respective owners.
Universal
Klip Case
USB Charging CableSocketScan™
800 Series
Micro USB Port
Lanyard Hook
Lanyard Attachment (not included)
Top LED
Side LED
Power button
Scan Trigger button
Socket Mobile’s barcodes scanners can be wiped clean with a cloth
dampened with isopropyl alcohol or water. Or, the barcode scanners can
be wiped clean with a Sani-Cloth.
Warning: DO NOT IMMERSE IN WATER (scanner’s mechanics could be
damaged)
DO NOT USE BLEACH FOR CLEANING (scanner’s material property may be
affected)
PRODUCT INFORMATION
CHARGE THE BATTERY
4
CHARGE THE BATTERY
1. Insert charging cable into an AC charging adapter
(not included - most smartphones and tablets come with AC
Adapters that look something like this.)
2. Plug charging adapter (not included) into an outlet.
3. Insert Micro USB into the 800 Series USB port.
4. The 800 Series will beep twice indicating adequate power is being
supplied to the unit.
5
Side LED status
• Red = Charging
• Green = Fully charged
Note: The SocketScan comes with a pre-installed
rechargeable Lithium Ion battery, the initial full charging of the battery
can take up to 4 hours.
Power On
Press and hold down the small power button on the side until the
SocketScan beeps twice (low-high tone).
4 Hours
OPTIONAL CHARGING ACCESSORIES
SCANNING BARCODES
6
DuraCase
Socket Mobile DuraCase™ combines and safeguards
both the 800 Series and mobile device as a one-handed
scanning solution that simultaneously charges both
devices.
Available for Apple® iPod touch®, Samsung J3/J5* and
Samsung S7*.
Watch our video on how to setup your DuraCase.
*On Samsung mobile devices, be sure to disable Fast Charge.
DuraCase
Charging Dock
DuraCase
6 Multi-Bay Charger
Due to varying countries’ outlets,
the DuraCase 6 Multi-Bay Charger
power cords are NOT included in the
package.
DuraCase
Charging Adapter
SCANNING BARCODES
7
After connecting the SocketScan to your device, open an application.
Place the cursor where you want to enter the scanned data.
1. Hold the SocketScan a few inches from the barcode.
2. Aim, press and hold the trigger button.
By default, the SocketScan will beep, vibrate, and the side LED will
ash green to conrm successful scan.
SocketScan S800
~4” to 8”
scanning distance
SocketScan S850
~6” to 12”
scanning distance
BLUETOOTH CONNECTION MODES
BLUETOOTH CONNECTION MODES
8
Connect your scanner using one of the following Bluetooth connection modes:
Bluetooth Connection Proles
Bluetooth Mode Description
Basic Mode (HID)
(Default)*
Human Interface
Device Prole
• NO software installation required
• Connects to most devices
• Good for barcodes containing small amounts
of data
• Scanner interacts with host device like a
keyboard
Application Mode
(SPP)
Serial Port Prole
For Android or Windows
• Software installation is required
• More efcient and reliable data
communications for barcodes containing lots
of data
• If you have an application that supports
Socket Mobile Scanners this is the mode
recommended
Application Mode
(MFi-SPP)
Apple Specic
Serial Prole
For iOS Devices
• Must use with an App developed to work with
iOS devices
• Software installation is required
• If you have an iOS application that supports
Socket Mobile Scanners this is the mode you
want to use
*By default, the scanner is set to Basic Mode (HID).
BLUETOOTH CONNECTION MODES
9
Operating System Connection Options
Operating
Systems
(OS)
Devices
Bluetooth
HID
Support
Bluetooth
SPP
Support
Bluetooth
Apple
Serial
Specic
(MFi Mode)
Android
Android 4.0.3 &
later
Yes Yes N/A
Apple iOS
iPod, iPhone, &
iPad
Yes N/A Ye s
Windows PC Windows 7, 8, 10 Yes Yes N/A
Mac OS
Mac OS X 10.4 to
10.X
Mac Books, Mac
Mini, & iMac
Yes No N/A
Note: To switch from one mode to the other you must remove the
pairing information from both devices - host computer and the scanner.
(see unpairing procedure on page 16)
The SocketScan will unpair and automatically power off. The next time you
power on the SocketScan, it will be
discoverable.
Select the appropriate mode and pair with the second host device.
BASIC MODE (HID)
BASIC MODE (HID)
Android: Connect Android Device in Basic Mode (HID)
In this mode the scanner functions and communicates similar to a keyboard. Therefore, scanner will work with Notes, and any other
application that supports an active cursor.
1. Power on the scanner. Make sure the scanner is
discoverable (unpaired) and the blue light blinks fast.
2. Go to Settings | Bluetooth.
3. Make sure the device’s Bluetooth is turned “On” to scan for devices.
4. In the list of found devices, select Socket CHS [xxxxxx]. Tap Pair.
5. The scanner will connect to the Android device.
6. The scanner will beep once after it has connected.
Note: If you have trouble connecting or pairing with host device, turn
host device’s Bluetooth off/on, and/or perform factory reset to the
scanner (see page 44).
Now you are ready to scan barcodes!
To connect to a new device or use a different prole (mode) on
the same device, you must rst unpair the scanner (see page 22).
10
BASIC MODE (HID)
Apple: Connect Apple iOS Device or Mac OS Device in Basic Mode
In this mode the scanner functions and communicates similar to a keyboard. Therefore, scanner will work with Safari, Notes, and any other
application that support an active cursor.
1. Power on the scanner. Make sure the scanner is
discoverable (unpaired). The Blue light blinks fast.
2. Start a Bluetooth device search.
• Settings | Bluetooth: Turn on Bluetooth and search for device.
• Mac OS: Click System Preferences | Bluetooth. A Bluetooth device
search will begin.
3. In the device list, tap on CHS [xxxxxx].
4. The scanner will connect to the Apple device.
5. The scanner will beep once after it has connected.
Now you are ready to scan barcodes!
To use the virtual keyboard while the scanner is connected, double tap
on the power button (similar to double clicking a mouse).
To connect to a new device or use a different prole (mode) on
the same device, you must rst unpair the scanner (see page 22).
11
BASIC MODE (HID)
APPLICATION MODE (SPP)
Windows: Connect Windows PC
1. Power on the scanner. Make sure the scanner is discoverable (unpaired).
2. Use your computer’s Bluetooth Settings to connect to the scanner.
3. Select “Add a device”.
4. In the device list, select Socket CHS [xxxxxx]. Click Next.
5. If a passkey is requested, enter 0000 (four zeroes). Click OK.
6. Follow the remaining screens to complete the wizard.
Note: On some computers the DuraScan will have to be congured as a
peripheral class of device. Please, refer to the Command Sheet Barcode
for details.
12
APPLICATION MODE (SPP)
13
Connect Android & Windows Device Quickly:
1. Download the latest SocketScan 10 software from
Socket Mobile’s support web page.
2. Power on the scanner and scan this barcode. The scanner will beep 3
times.
3. Turn Bluetooth on for your device. Go to Settings > Bluetooth.
A Bluetooth Devices search will begin.
4. Tap Socket CHS[xxxxxx] in the list of Devices found. After a few
seconds the “Not Paired” status will change to “Connected” and the
scanner’s Blue LED will blink every 3 seconds conrming the
connection.
APPLICATION MODE (SPP)
APPLICATION MODE (SPP)
14
Connect Android device in Application Mode using EZ Pair
Install Software
1. Go to GooglePlay Store, search for “SocketScan ”.
2. Download & install. Follow the on screen instructions.
Getting Started
3. Follow the on screen instructions.
4. Tap on screen the ON SCREEN button.
5. Tap on screen the 1D SCANNER button.
6. Scan the barcode on the device screen. Wait a few seconds. The
scanner will beep 3 times indicating it has accepted the command to
connect to your device.
7. When notied of a pairing request, swipe the notication icon down,
then tap Pairing request.
8. On the next screen, tap Pair.
9. The scanner will beep once to indicate connected state and is ready
to scan barcodes. Tap Back to close Socket EZ Pair.
10.If you are connecting a scanner which is not registered, a scanner
registration icon will appear on top of the screen. Swipe the icon
down to open the registration screen. Follow the instructions
to register your Scanner. Socket Mobile highly recommends that
all customers register their products for future updates, but
registration is optional.
Now you are ready to scan barcodes!
APPLICATION MODE (SPP)
15
Connect Windows PC in Application Mode
Note: Make sure you have administrative privileges.
1. Download the latest SocketScan 10 software from Socket Mobile’s
support web page.
2. Follow the on-screen instructions to install the software.
3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM
port.
Note: If there is none please click Ports to create at least one new
incoming COM port in Bluetooth settings.
4. Click Finish.
Now you are ready to scan barcodes!
APPLICATION MODE (SPP)
APPLICATION MODE (MFi-SPP)
16
To pair the scanner with Windows PC using EZ Pair:
1. Power on the scanner. Make sure the scanner is available to be
connected to Bluetooth (unpaired).
2. Launch SocketScan 10 and click on the SocketScan 10 icon in the task
tray. In the pop-up menu, click Socket EZ Pair.
3. Click 1D Scanner (S800) or 2D Scanner (S850) accordingly.
4. Scan the barcode that appears on the screen.
5. The PC will automatically try to pair with the scanner. If prompted
to allow the pairing, click Yes. If prompted for a passkey, enter 0000
(four zeroes).
6. After the scanner connects, it will beep once. Close Socket EZ Pair.
6a. In Windows 10 if this step can not be done, open the Bluetooth
settings and add and pair the scanner manually.
7. If you are connecting a scanner which is not registered, a
scanner registration icon will appear on top of the screen. Follow
the instructions to register your scanner. Socket Mobile highly
recommends that all customers register their products, but
registration is optional.
8. The task tray icon will change to indicate the status of the
connection.
Now you are ready to scan barcodes.
APPLICATION MODE (MFi-SPP)
Connect Apple iOS device in Application Mode
Please check with your scanner application vendor or visit
www.socketmobile.com/appstore to conrm your scanner-enabled
application supports the scanner.
If you are using the scanner with an Apple iOS device and a
scanner-enabled Application that does not provide instructions how to
connect your scanner, please use the following steps.
1. Power on the scanner. Make sure the scanner is discoverable
(unpaired). The Blue light should be blinking fast.
2. To change the prole to Application Mode scan this barcode. The
scanner will beep 3 times.
Use with iPad, iPod touch, and iPhones.
(Scanning this barcode changes the connection mode)
3. Turn on Bluetooth on the Apple device. Go to Settings > Bluetooth. A
Bluetooth Devices search will begin.
4. Tap Socket CHS[xxxxxx] in the list of other devices found. After a
17
APPLICATION MODE (MFi-SPP)
ALWAYS ACTIVE MODE
18
few seconds the “Not Paired” status will change to “Connected” or
“Paired” and the scanner blue LED will stop blinking and turn solid
blue.
Note: The characters in brackets are the last 6 characters of the
Bluetooth Address.
5. Launch your scanner-enabled Application. The scanner will beep
once indicating that it is connected to the appropriate application.
Now you are ready to scan barcodes!
ALWAYS ACTIVE MODE
For busy days on the job, try using the Active Mode to keep you moving
faster. Avoid the hassle of turning the scanner on again and reconnecting to your host device.
Scan one of the barcodes below and recongure the scanner to remain
on longer.
Note: Turn off the host device’s Bluetooth prior to scanning one of the
alternate timer barcodes. Then turn the Bluetooth back on.
Power cycle the scanner (turn off/on).
Scanner Always On*
Congures the scanner to never power off.
Constant Power for 8 hours*
Scan Barcode to congure the scanner to remain on for 8 hours.
Constant Power for 4 hours*
Scan Barcode to congure the scanner to remain on for 4 hours.
19
ACTIVE MODE
BLUETOOTH UNPAIRING
20
*These settings drain the battery faster. It is assumed you will charge
the scanner within a 24-hour period or overnight. If you don’t, the
scanner’s battery will drain completely.
Return Scanner to Default Settigs
Turns the scanner off when it is not in use – 3 to 5 minutes after being
disconnected from host device.
BLUETOOTH UNPAIRING
Note: This procedure will put the SocketScan in discoverable mode.
Step 1: Unpairing the scanner: Delete the Bluetooth Pairing
If the scanner is paired with a device, unpair it before trying to
connect to a different device.
a. Power on the scanner.
b. Press the trigger button then power button and hold both until
you hear 3 beeps.
The scanner will unpair and automatically power off. The next time you
power on the scanner, it will be discoverable.
Step 2: Remove or forget the scanner from the Bluetooth list on the
host device.
Important: Both steps above must be done to complete
the unpairing.
21
FACTORY RESET
RESTORE METHOD
Factory Reset will restore the scanner to Factory Default settings
(congured as shipped). If your scanner cannot scan the Factory Default
barcode on page 35, then Follow this Factory Reset (button) sequence:
1. Turn ON the scanner.
2. Press and hold the trigger button1, then quickly press and release
the power button2, while continuing to hold the trigger button.
3.
4. Let go of trigger button after the scanner beeps once (after 15
seconds). Five conrmation tones will sound from high to low tones
and then the scanner will turn OFF.
Note: If you follow this sequence, but release the trigger button too
early (before 15 seconds and the beep) the Factory Reset will have
failed.
22
Quickly press
and release the
power button
1
2
Power Button
Trigger Button
RESTORE METHOD
NOTE: If your scanner remains in an unresponsive state after following
the Factory Reset, use the Restore Method as a last resort.
The Restore Method should be the last attempt used to revive an
unresponsive scanner. It will reinitialize the core hardware.
1. Make sure your scanner is OFF.
2. Press and hold the power button until the LED light goes on and off
(about 15 seconds)
23
STATUS INDICATORS
STATUS INDICATORS
Top LED
Bluetooth
LED Activity Meaning
Quick Blinking Blue
(2 blinks every
second)
Discoverable - waiting for
a host Bluetooth connection.
Slow Blinking Blue
(1 blink every
second)
Attempting to connect to
a paired device. Searching
the last known Host.
Note: Will STOP attempting after approx. 1
minute.
Solid Blue Scanner connected
Side LED LED Activity Meaning
Blink Green Once Good Scan/Read
Side LED
Battery Status
LED Activity Meaning
Solid Red
(while charging)
Charging the battery
Blinking Red
Battery capacity
below 20%
Solid Green
(while charging)
Battery is 100% full
24
STATUS INDICATORS
25
Beep Pattern Sound Meaning
Low-High Tone Power On
High-Low Tone Power Off
High-High Tone
Power Supply detected and scanner started
charging
1 Low Beep
Scanner has toggled on-screen keyboard
or keyboard toggle feature is enabled (iOS
devices only)
1 Beep
Scanner connected to device and is ready to
scan barcodes
1 Beep Data successfully scanned
2 Beeps (same tone) Scanner disconnected
1 Long Beep Scanner gave up searching for a host
3 Beeps
(escalating tone)
Scanner has been recongured (the command
barcode was scanned successfully)
3 Beeps (escalating
tone followed by
long tone)
The command barcode did NOT work! (Verify
if the command barcode used is valid for your
scanner and try again)
PRODUCT SPECIFICATIONS
PRODUCT SPECIFICATIONS
Vibrate Meaning
Vibrate Data successfully scanned
Command Barcodes are available on pages 43-46 to modify the
LED, beep, and vibrate settings.
If you are using a scanner-enabled application, typically the
application provides settings for LED, beep, and vibrate settings.
Conguration Settings
Time after powering on
Scanner
Bluetooth mode
0-5 minutes Discoverable and connectable
5 minutes
If connection is not made, scanner
powers off
2 hours
If your scanner is connected but not
used it will power off in 2 hours.
When trigger button is pressed the
timer is reset.
26
PRODUCT SPECIFICATIONS
27
Specications S800 S850
Dimensions
(L x W x H)
3.42 x 0.52 x 2.12 in. (86.9 x 53.94 x 13.43 mm)
Total Mass 1.7 oz (48.2 g)
Antimicrobial Antimicrobial additive in external surfaces
Battery Lithium ion rechargeable battery
Charge Time 4 Hours
Battery Life -
Per Full Charge
8,000 scans within
9 hours (calculation
based on 1 scan every
4 seconds)
34,000 scans within 3
hours (based on 2 scans
every 1 second) or
1,000 scans within 10
hours (based on 1 scan
every 4 seconds)
Note: Battery life varies depending on ambient
temperature, ambient light, and age of battery.
Bluetooth Version
Class 1 Bluetooth v2.1 + EDR with 56 bit data
encryption
Wireless Range Up to 10 m (33 ft), depending on environment
Scanner Type 1D Linear Imager
2D/1D Omni-directional
Imager
PRODUCT SPECIFICATIONS
HELPFUL RESOURCES
28
Specications S800 S850
Symbologies
All major 1D
barcodes
All major 1D and 2D
barcodes
Supported
Language Settings
[in Basic Mode (HID)]
English, French, German, Spanish
Systems/Battery
Charging Requirement
USB Type 5V 1A
Ambient Light From 0 to 100 000 lux
Operating
Temperature
+32 to +122°F (0 to +50°C)
Storage Temperature -22 to +158°F (-30 to +70°C)
Relative Humidity 5% to 95% non-condensing
Sealing IP40
Drop Specications
Multiple 3.3 ft (1 m) drops to vinyl covered
concrete
HELPFUL RESOURCES
29
Technical Support & Product Registration:
https://support.socketmobile.com
Phone: 800-279-1390 +1-510-933-3020 (worldwide)
Warranty Checker:
https://www.socketmobile.com/support/warranty-checker
Socket Mobile Developer Program:
Learn more at: http://www.socketmobile.com/developers
The User’s Guide (full installation and usage instructions) and Command
Barcodes (Advanced Scanner Congurations) can be download at:
https://www.socketmobile.com/support/downloads
REGULATORY COMPLIANCE
REGULATORY COMPLIANCE
30
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise
for digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
REGULATORY COMPLIANCE
31
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an
independent laboratory. The unit under test was found compliant with
all the applicable Directives, 2004/108/EC and 2006/95/EC.
This product is compliant to Directive 2002/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their
useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
NON-MODIFICATION STATEMENT
Changes or modications not expressly approved by
the party responsible for compliance.
For more warranty information, please visit:
https://www.socketmobile.com/support/downloads
WEEE
LIMITED WARRANTY
COMMAND BARCODES
32
Socket Mobile Incorporated (Socket) warrants this product against
defects in material and workmanship, under normal use and service,
for one (1) year from the date of purchase. Product must be purchased
new from a Socket Authorized Distributor or Reseller. Used products and
products purchased through non-authorized channels are not eligible for
this warranty support.
Warranty benets are in addition to rights provided under local
consumer laws. You may be required to furnish proof of purchase details
when making a claim under this warranty.
Consumables such as batteries, removable cables, cases, straps,
and chargers: 90 day coverage only
For more warranty information, please visit:
https://www.socketmobile.com/support/downloads
COMMAND BARCODES
Important! Make sure the scanner is not connected to a host
computer or device before scanning a command barcode!
Bluetooth Connection Modes
Basic Mode (HID)
(default)
Congures the Scanner to
Human Interface Device
(HID) mode as a Keyboard
class device
#FNB00F40001#
Application Mode (SPP)
Changes the Scanner to Se-
rial Port Prole (SPP) mode
#FNB00F40000#
Application Mode
(MFi-SPP)
Changes the Scanner to MFi
mode for Apple iOS Devices
#FNB00F40002#
33
COMMAND BARCODES
Important! Make sure the scanner is not connected to a host
computer or device before scanning a command barcode!
Beep Settings
Beep after
scanner Decodes
Data ON (default)
Enables scanner
to beep to indicate successful
scans.
#FNB0119E0001
00030078004B#
Beep after scanner
Decodes Data
OFF
Disables scanner
from beeping to
indicate successful scans.
#FNB01190E00010
0000078004B#
COMMAND BARCODES
34
COMMAND BARCODES
Vibrate Settings
Vibrate ON (default)
Enables scanner to
vibrate to indicate
successful scans.
#FNB01310001000100F
A0000#
Vibrate OFF
Disables scanner from
vibrating to indicate
successful scans.
#FNB013100010000#
Factory Default
Factory Reset
Revert all settings to
factory defaults. The scanner
will power off after scanning
this barcode.
#FNB00F0#
For more command codes go to:
https://www.socketmobile.com/support/download
35
2017
Extend Your Warranty...
Receive Priority Service and Personal Care.
You have 60 Days from purchase date to enroll in a SocketCare Service
Program!
For detailed information visit:
https://www.socketmobile.com/socketcare
Loading...