Socket CHS 7Qi Quick Start Manual

Download

CHS 7Qi

QUICK START GUIDE

www.socketmobile.com

Bluetooth Cordless Barcode Scanner

PACKAGE CONTENTS PRODUCT INFORMATION

© 2010-2014 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, and SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The Bluetooth word mark and logo are registered trademarks of the Bluetooth SIG, Inc. USA, and any use by Socket Mobile, Inc. is under license. All other trademarks and trade names contained herein may be those of their respective owners.

mobi le

mobil e

mobi le

Rechargeable

Li-ion battery pack

(installed)

AC adapter* & USB to

DC plug cable

*Use the plug that is

regionally appropriate

Lanyard

CHS 7Qi

Thank you for choosing Socket Mobile!

Let’s get started!

*Also used for keyboard Pop-up (HID Mode only)

Scanner head

Product label

Lanyard

Blue/Green/Red LED

Trigger button

Power button*

DC-in connector

Battery door

Twist-lock (horizontal/unlocked)

Twist-lock (vertical/locked)

Pins for charging cradle

SCANNER SETUP

Lock

Unlock

Battery door removal

Unlock the Battery door by using a thin coin to turn the lock under the CHS to a horizontal position (turn

90 degrees).

Attach the Lanyard (optional) Detach the string loop of the tether

from the lanyard. Then feed the string loop through the slot in the Twistlock and then through the end of the loop. Pull tight so the string loop is secure to the Twist-lock, Reattach the string loop to the tether from the Lanyard.

If desired, attach the tether to a lanyard or belt.

CHARGE THE BATTERY

Charge the CHS

The CHS must be fully charged be-

fore rst use. Please allow 4 hours

uninterrupted charging for the initial battery charge.

• Red LED = Charging

• Green LED = Fully charged

Charging from a computer USB port

is not reliable and not recommended.

Socket Mobile offers a Charging Cradle (optional Accessory/sold separately) which is a convenient holder that charges the scanner when not in us

Cradle Sku#

CHS 7Qi: AC4054-1381

CHS 7Xi: AC4055-1382

CHS 7XiRx: AC4056-1383

o b

i l

4 5

BASIC FUNCTIONALITY

•Powering On:

Press and hold down the small power button until the LED turns Blue and the CHS beeps twice (low-high).

•Powering Off/Disconnecting:

Press and hold down the small power button until the CHS beeps twice (high-low).

BASIC FUNCTIONALITY (CONTINUED)

Scanning Barcodes:

After connecting the CHS to your device, open an application and put the cursor where you want to enter data.

Hold the CHS about 4 inches (10 cm) from the barcode and press and

hold the trigger button. Position the CHS so the Red beam covers the entire width of the barcode. Keep your hand steady while scanning.

By default, the CHS will beep and vibrate, and the LED will ash Green to conrm that data was decoded and sent to the device.

o b ile

Aim the scan beam straight

across the entire barcode.

Aim at the center.

o b i

l e

mobi le

6 7

Power button

CONNECTION MODES (CONTINUED)

CONNECTION MODES

HID Keyboard Emulation mode (default)

In HID mode the CHS emulates a keyboard. This is a universal connection

method and will work with any application that has a text eld.

The application receives the data input from the CHS. The CHS includes a keyboard pop-up feature so you can disable the CHS and accept data

input from the onscreen keyboard on the device. Pages 10-11 provides

the connection steps using HID mode.

MAC OS devices are connected using HID mode.

iOS devices are connected using either iOS mode or HID mode, but not both together.

The CHS is connected to your iOS device using one of the following modes:

1. iOS mode

2. HID Keyboard Emulation mode (default)

iOS mode

iOS mode is used with a Scanner-enabled Application. Scanner controls are embedded in the Application to provide better performance, secu-

rity, features, and domain-specic capabilities.

If you purchased a Scanner-enabled Application on the Apple App Store (or through the Apple Volume Purchase Program for Business) that features integrated support for the CHS, we recommend you install that Application on your device and follow the Application instructions to connect with the CHS. If the connection steps are not documented in

the Application, please see pages 12-13 for the connection steps using

iOS mode.

Please visit the Socket Mobile App Store to conrm your Scanner-enabled Application supports the CHS.

http://www.socketmobile.com/appstore

HID (KEYBOARD EMULATION) MODE

HID (KEYBOARD EMULATION) MODE (CONTINUED)

To pair the CHS with the Apple device in HID mode: (required only the

rst time you connect).

1. Power on the CHS. The Blue LED should blink every second indicating

Bluetooth is on but not Connected.

2. Turn Bluetooth on for the Apple device. Go to Settings > Bluetooth. A Bluetooth Devices search will begin.

An iOS device is always Discoverable when in the Bluetooth menu is active. A MAC OS device provides an option to turn Discoverable On or Off. Conrm the MAC OS device is Discoverable.

3. Tap Socket 7Xi [xxxxxx] in the list of Devices found. After a few sec-

onds the “Not Paired” status will change to “Connected” and the CHS

Blue LED will blink every 3 seconds indicating it is Connected.

The characters in brackets are the last 6 characters of the

Bluetooth Address. The full Bluetooth address is printed in the Product label (remove the battery door).

You are now ready to scan barcodes, see instructions on page 7.

Keyboard Pop-up Enable

The CHS emulates the keyboard in HID mode. So scanned barcode data

will be input into the text eld. The following steps show how to access

the onscreen keyboard while connected to the CHS in HID mode.

1. Make sure the CHS is connected to your Apple device in HID mode.

2. Open your application and place the cursor where you want to enter

data.

3. Quickly double-press the power button of the CHS (like doubleclicking a mouse) to open or close the onscreen keyboard. The

CHS will beep once as conrmation.

To connect to a new Apple device, you must rst unpair the CHS

and remove the CHS from the Bluetooth list in your device. See

page 15.

IOS MODE - SCANNER-ENABLED APP IOS MODE - SCANNER-ENABLED APP (CONTINUED)

If you are using a Scanner-enabled Application, follow their instructions to connect with the CHS. Many applications include these steps and barcodes in the set-up procedure.

If you are using an Application that connects to the CHS using HID

Keyboard Emulation mode, follow the instructions on pages 10-11. iOS

mode should not be used.

If you are using the CHS with an iOS device and a Scanner-enabled Application that does not provide instructions to connect with the CHS, please use the following steps.

1. Power on the CHS and scan this barcode. The CHS will beep 3 times.

2. Turn Bluetooth on for the Apple device. Go to Settings > Bluetooth. A Bluetooth Devices search will begin.

3. Tap Socket Socket 7Xi [xxxxxx] in the list of Devices found. After a few seconds the “Not Paired” status will change to “Connected”

and the CHS Blue LED will blink every 3 seconds conrming the

connection.

The characters in brackets are the last 6 characters of the

Bluetooth Address. The full Bluetooth address is printed in the Product label (remove the Battery door).

4. Open the Scanner-enabled Application. The CHS will beep once indicating that the application is in control and you are ready to scan. It should now be connected to the CHS.

You are now ready to scan barcodes with the Scanner-enabled Application, see instructions on page 7.

Unpairing the CHS: Deleting the Bluetooth Pairing

In most cases, if the CHS is paired with a device, you should unpair it before trying to connect to a new device.

1. Power on the CHS.

2. Press and hold down the trigger button.

3. Press and hold down the power button.

4. After you hear 3 beeps, release both buttons.

The CHS will unpair and automatically power off. The next time you power on the CHS, it will be discoverable.

Remove the CHS from the Bluetooth list in your iOS device

To Unpair the CHS on your device, go to Settings > Bluetooth, tap i

next to the Socket 7Xi [xxxxxx] name, then tap “Forget this Device”.

APPENDIX

The remaining pages provide reference material on how to better use the CHS. We recommend you review this material and save for future reference.

BLUETOOTH UNPAIRING

Automatic Reconnections

After you power on the CHS, it will automatically try to connect to the last device it was connected to.

• Make sure the device is in range with Bluetooth On.

• If using HID mode, pressing the Trigger button will enforce the con-

nection.

• If using iOS mode, make sure the Scanner-enabled Application is active.

While the CHS is attempting to connect the Blue LED will blink every second.

• If a connection is made, the Blue LED will blink every 3 seconds.

• If a connection is not made after 30 tries, the CHS will emit a long

beep.

il e

Scan command barcode(s) to quickly congure the CHS.

Make sure the CHS is not connected to a device before scanning a command barcode!

For a complete set of command barcodes, download the Command Barcodes Sheet: www.socketmobile.com/pdf/data-collection/

command-barcodes-sheet_7X.pdf

This web link is also provided in the below QR code.

COMMAND BARCODES

BLUETOOTH CONNECTION

Vibration and Beep Settings

Enable Vibration and Beep

(default)

Disable Vibration only

Disable Vibration and Beep

Disable Beep only

COMMAND BARCODES (CONTINUED)

Bluetooth Connection Modes

HID-keyboard (default)

iOS Mode

COMMAND BARCODES (CONTINUED)

Factory Default

Factory Reset

Revert all settings to factory defaults. The CHS powers off after scanning this barcode.

STATUS INDICATORS

Status LED Activity Meaning

Bluetooth 1 Blue blink every

second

Bluetooth is On but not connected.

1 Blue blink every 3

seconds

CHS is connected to device.

Good Read Green constant

(while scanning)

Data successfully scanned.

Battery Status Green constant

(while charging)

Battery is fully charged.

Red Blinking (while scanning and no AC power)

20% or less battery

capacity remaining.

Red constant (While AC power)

Battery is charging.

Off (while no AC power)

CHS is Off.

Data Sufx

CarriageReturnSufx (default) TabSufx

Carriage Return & Line Feed

Sufx

COMMAND BARCODES (CONTINUED)

DataAsIs-NoPrexorSufx

STATUS INDICATORS (CONTINUED)

Vibrate Meaning

Vibrate Power On or data successfully

scanned.

Command barcodes are available on page 19 to modify the LED,

beep, and vibrate settings.

If you are using a Scanner-enabled Application, typically the application provides settings for LED, beep, and vibrate settings.

Bluetooth Mode Sequence

Time after powering on CHS Bluetooth mode

0-5 minutes Discoverable and connectable

5 minutes If a connection is not made, the

CHS will power off.

If a device connects to the CHS, it stays on for 2 hours then turns

off if a button is not pressed. If a button is press the timer is

reset to expire in another 2 hours.

STATUS INDICATORS (CONTINUED)

Beep Pattern Meaning

Low-high tone Power On

High-low tone Power Off

1 low beep Keyboard Pop-up Enable.

1 beep CHS connected to device and ready to scan bar-

codes.

1 beep with

Green LED blink

Data successfully scanned.

2 beeps, same

tone

CHS disconnected from device.

1 long beep CHS tried multiple times unsuccessfully to con-

nect to the last device it paired with. After 5

minutes the CHS will power off.

3 beeps with

escalating tone

CHS recognized the Command Barcode and implemented the change.

3 beeps with

escalating tone followed by a long tone

CHS recognized the Command Barcode, but could not implement the change. Verify the Command Barcode is valid and retry.

HELPFUL RESOURCES

Technical Support & Product Registration:

http://support.socketmobile.com

Phone: 800-279-1390 +1-510-933-3020

Warranty Checker

www.socketmobile.com/support/warranty-checker

Socket Mobile Developer Program:

Learn more at: http://developer.socketmobile.com

The User’s Guide (full installation and usage instructions) and Command

Barcodes (Advanced Scanner Congurations) can be download at:

www.socketmobile.com/support/downloads/data-collection/series7/

ss10/?page=series

This web link is also provided in the below QR code

PRODUCT SPECIFICATIONS

Specications CHS 7Qi CHS 7Xi CHS 7XiRx

Dimensions

5.07 x 1.57 x 1.36 in. (129 x 40.1 x

34.6 mm)

5.2 x 1.77 x 1.49 in. (132 x 45.1 x

37.9 mm)

Total Mass

1.6 oz (45 g)

3.2 oz (90.7 g)

Antimicrobial

Antimicrobial additive in all external surfaces

Operating Temp

+32 to +122°F (0 to + 50°C)

Battery Life

10 hours or 1,000 scans

Charge Time

4 hours fully charged

Bluetooth Version

Bluetooth v2.1 + EDR with 56 bit data encryption

Wireless Range

33 ft (10 m)

Scanner Type

Omni-directional Imager (2D)

Symbologies

All major 1D and barcodes

Supported Language Settings (in HID mode)

English, French, German, Spanish

Supported Language Settings (in iOS mode)

All languages supported by Apple

NOTES

Model _______________________________________

Serial No. ____________________________________

Bluetooth Address _____________________________

Date of Purchase ______________________________

FCC WARNING STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

CANADIAN DOC STATEMENT

This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out in

the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites ap-

plicables aux appareils numériques de las classe B prescrites dans le Réglement sur le brouillage

radioélectrique édicté par les ministère des Communications du Canada.

CE MARKING AND EUROPEAN UNION COMPLIANCE

Testing for compliance to CE requirements was performed by an independent laboratory. The unit

under test was found compliant with all the applicable Directives, 2004/108/EC and 2006/95/EC.

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

The WEEE directive places an obligation on all EU-based manufacturers and importers to take-back electronic products at the end of their useful life.

ROHS STATEMENT OF COMPLIANCE

This product is compliant to Directive 2002/95/EC.

NON-MODIFICATION STATEMENT

Changes or modications not expressly approved by

the party responsible for compliance.

RoHS

QuickStart Guides in other languages are available for download at: http://www.socketmobile.com/AppleQSG.aspx

2015

Socket CHS 7Qi Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual