4-Amp 12-Inch Electric Grass Trimmer/Edger
4-Amp 12-Inch Electric Grass Trimmer/Edger
Model No. TRJ601ERM
®
A Division of Snow Joe
, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
mCAUTION!
Before using this electric tool, carefully read and observe the
safety rules and instructions listed below. Before starting work,
make sure that you know how to stop the machine in case of
an emergency. The incorrect use of this machine could cause
serious injury. Keep these instructions in a safe place and on
hand so that they can be consulted when required.
mCAUTION!
The electric grass trimmer should only be used for cutting
lawns and for trimming along the borders of ower beds. Other
uses of the trimmer that are not indicated in these instructions
could damage the trimmer or seriously injure the operator.
GENERAL Safety Rules
mWARNING: When using the electric grass trimmer,
basic safety precautions should always be followed to reduce
the risk of re, electric shock, and personal injury, including the
following:
a) FOR ALL DOUBLE–INSULATED APPLIANCES
1. Replacement parts – When servicing, use only
identical replacement parts.
2. Polarized appliance connections – To reduce the risk
of electric shock, this appliance has a polarized plug
(i.e. one blade is wider than the other) and will require
the use of a polarized extension cord. The appliance
plug will t into a polarized extension cord only one
way. If the plug does not t fully into the extension
cord, reverse the plug. If the plug still does not t,
obtain a correct polarized extension cord. This plug
will t into the polarized wall outlet only one way. If the
plug still does not t fully into the wall outlet, reverse
the plug. If the plug still does not t, contact a qualied
electrician to install a proper wall outlet. Do not change
the appliance plug, extension cord receptacle, or
extension cord plug in any way.
Form No. SJ-TRJ601ERM-880E
OPERATOR’S MANUAL
b) FOR ALL APPLIANCES
1. Avoid dangerous environments – Do not use
appliances in damp or wet locations. Do not use
in rain.
2. Keep children and bystanders away – Children and
other spectators, including pets, should be kept at
least 50 feet (15 meters) away from the work area.
When the grass is cut, stones and debris contained
in the grass can be picked up by the trimmer and
dispersed into the air. These ying projectiles can
cause blindness or other bodily injury.
3. Dress properly – Always wear suitable clothing
when using the trimmer to prevent head, hand, or
feet injuries. Do not wear loose clothing or jewelry.
They can get caught in moving parts.
4. Use safety glasses – Also use safety footwear,
snug-tting clothing, protective gloves, hearing and
head protection.
5. Use the right tools – Do not use tools for any job
except that for which they are intended.
6.
mWARNING! To reduce the risk of electric shock,
use only with an extension cord intended for outdoor
use, such as an extension cord of cord type SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A,
or SJTOW-A.
7. Avoid unintentional starting – Do not carry pluggedin tool with nger on the trigger. Make sure the switch
is off before plugging in the tool.
8. Do not abuse the cord – Never carry the tool by
the cord or yank the cord to disconnect it from the
receptacle. Keep cord away from heat, oil, and sharp
edges.
9. Do not force the tool – It will do the job better and
with less likelihood of injury if it is used at the rate for
which it was designed.
10. Do not overreach – Keep proper footing and balance
at all times.
11. Stay alert – Watch what you are doing. Use common
sense. Do not operate the trimmer when you are tired,
or under the inuence of aclcohol or drugs.
12. Disconnect the tool – Turn the trimmer off and
disconnect the plug when: the trimmer is not in use;
it is left unattended; it is being examined because it
is not working correctly; the power supply cable is
damaged; the blade is being removed or changed
or when the trimmer is being moved from one place
to another.
13. Store idle tools indoors – When not in use, tools
should be stored indoors in a dry and high or
locked-up place out of the reach of children.
© 2013 by Snow Joe, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
14. Maintain tools with care – Keep cutting edges sharp
and clean for best performance and to reduce the
risk of injury. Follow instructions for lubricating and
changing accessories. Inspect the trimmer periodically
and replace if damaged. Repair the trimmer only at an
authorized service facility. Keep handles dry, clean,
and free from oil and grease.
15. Checked for damaged parts – Before continuing to
use the trimmer, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for the alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect the trimmer’s operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
c) ADDITIONAL SAFETY INSTRUCTIONS FOR GRASS
TRIMMER/EDGER
1. Keep guards in place and in working order.
2. Keep hands and feet away from the cutting area.
mCAUTION!
The safety guard is critical to the safety of the operator and the
safety of people standing within a safe distance of the trimmer.
The safety guard keeps the trimmer in good working order and
must always be in place during operation.
• Do not try to stop the cutting device (nylon line) with your
hands. Always let it come to a stop by itself.
mWARNING! After switching off the tool, the cutting device
continues to rotate for a few seconds.
• Only use the original type of nylon line. Do not under any
circumstances use metal line instead of nylon line.
• Do not use the tool to cut grass which is not on the ground.
For example, do not cut grass growing on walls or rocks.
• Do not switch on the tool in an enclosed or poorly ventilated
space or in the presence of ammable and/or explosive
substances such as liquids, gases and powders.
• Only cut during broad daylight or with adequate articial
light.
• Check that all grass cuttings and dirt have been removed
from the ventilation vents.
• Do not cross roads or gravel paths while the tool is still
running.
• When the tool is not in use, store it in a dry place and out of
reach of children.
• After use, disconnect the tool from the power supply and
check for damage. If you have the slightest doubt about the
condition of the tool, contact an authorized service center.
• Only use the tool according to the instructions given in this
manual.
• Check regularly that the screws are tight.
• Do not try to repair the tool or access internal parts.
Contact an authorized service center.
Extension Cords
• Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size
to use depending on cord length and nameplate Ampere
rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
• Ground Fault Circuit Interrupter (GFCI) protection should
be provided on the circuits or outlets to be used for this
electric trimmer. Receptacles are available with built-in
GFCI protection and may be used for this measure of
safety.
• Use only UL listed extension cords. Inspect the extension
cord before use and never use damaged or altered
extension cords. Follow the extension cord manufacturer’s
safety instructions.
• To prevent the appliance cord from disconnecting from the
extension cord during operation, use the plug-receptacle
retaining straps provided or make a knot with the two cords
as shown in Table 2.
Table 1. Minimum Recommended Extension Cord Gauge
(AWG) Chart
Volts
120V
Ampere Rating
Table 2. Method of securing Extension Cord
Cord set Appliance cord
0 – 6
6 – 10
10 – 12
12 – 16
(A) Tie cord as shown
(B) Connect plug and receptacle
Total length of cord in feet
25
18
18
16
14
50
AWG
(Extension Cord Gauge)
16
16
16
12
Not Recommended
100
16
14
14
150
14
12
12
2
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbol Description
SAFETY ALERT – Indicates a precaution, a warning
or a danger.
READ THE OPERATOR’S MANUAL(S) Read, understand
and follow all instructions in the manual(s) before
attempting to assemble and operate.
WARNING! Keep out of rain and away from wet areas.
For protection against injury, wear safety goggles
and ear protection.
Wear protective gloves and non-slip footwear when
using the machine and handling debris.
DANGER! Beware of thrown objects to bystanders. Keep
bystanders at least 15 m (50 ft) away from the machine.
WARNING! Remove the plug from the mains if cable is
damaged or cut and replace damaged cord immediately.
DOUBLE INSULATION – When servicing, use only
identical replacement parts.
3
Know Your Electric Grass Trimmer/Edger
1. Handle
2. ON/OFF trigger
3. Safety button
4. Cable restraint
5. Handle knob
6. Auxiliary handle
7. Locking lever
8. Power cord
9. Telescopic shaft adjustment knob
10. Shroud
11. Safety guard
12. Cooling fan
13. Spool
14. Flower guard
1
2
4
5
180°
3
6
7
Technical Data
Rated Voltage 120 V – 60 Hz
Rated Power 4 amp
Maximum Cutting Diameter 12 in. (30 cm)
No Load Speed 8,800/min
9
8
10
11
13 1412
Line Diameter 0.063 in. (1.6 mm)
Spool Length 20 ft (6 m)
Spool Advance Bump Feed
4
Unpacking
Carton Contents:
• Grass trimmer/edger
• Safety guard
• Auxiliary handle
• Handle bolt and screws
• Safety and operating instruction manual
1. Carefully remove the contents from the shipping carton.
Make sure that all items listed in the carton contents are
included.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return to the store. Please call
1-866-766-9563.
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new Electric Grass
Trimmer/Edger.
Assembly
Before using the Electric Grass Trimmer/Edger, follow these
instructions to assemble:
NOTE: Observe correct mains voltage – The voltage of
the power source must match the voltage specied on the
nameplate of the unit.
Fitting Auxiliary Handle
1. Remove the trimmer and parts from the box.
2. Place the handle on the tool as shown (Fig. 1).
4. Assemble the auxiliary handle on the machine by inserting
the handle knob into the auxiliary handle and tightening
the handle with the bolt provided (Fig. 2).
Fig. 2
Bolt
Handle knob
5. Make sure that the handle assembly is tightly xed to the
machine body.
Fitting the safety guard
mWARNING! The guard must be properly installed.
The guard provides partial protection from the risk of thrown
objects to the operator and other bystanders.
1. Unplug the tool and remove the screws from the motor
housing.
2. Place the safety guard in the direction of the arrow shown
to align it with the screw holes on the motor housing
(Fig. 3).
Fig. 1
Auxiliary handle
3. Adjust the handle to the most comfortable position.
Fig. 3
Safety guard
3. Firmly press the safety guard into place and secure it to
the trimmer head with the screws provided (Fig. 4).
NOTE: Never use the tool unless the safety guard is
properly tted.
5
Fig. 4
Screws
Adjusting the telescopic shaft
1. Loosen the telescopic shaft adjustment knob.
2. Pull and adjust the shaft to a comfortable height (Fig. 5).
3. Tighten the knob once the desired length is achieved
(Fig. 5).
Fig. 5
Telescopic shaft
adjustment knob
mWARNING! Never use steel, wire, rope, string, or other
materials as cutting line. Other materials can break off during
cutting and become a dangerous missile that can cause
serious injury.
Application
Replacing the spool
1. Disconnect the main plug.
2. Press together both locking device tabs on the spool cover
and remove the cover (Figs. 7-8).
3. Remove the spool from the spool cover (Fig. 9).
4. Remove the spring and clean out any dirt or grass residue.
Fig. 7
Spool
cover
Locking
devices
Lower shaft
adjustment knob
to tighten
the knob
Adjusting the angle of cutting head
mWARNING! Always unplug the trimmer before making
any adjustments to the trimmer.
1. Slide the locking lever down and hold (Fig. 6).
2. Twist the operation handle to the desired position.
3. Release the locking lever.
Fig. 6
90°
Spool
Fig. 8
Fig. 9
Spool
180°
Locking
lever
6
Winding the line
NOTE: A dual-line factory wound spool (Model TRJ601ERS)
is available for easy spool replacement on the TRJ601E
electric grass trimmer. Visit www.snowjoe.com to purchase.
Should you wish to wind the line yourself, the instructions are
provided below. Self-winding, however, is NOT recommended
because if the line is not wound properly it can cause the
trimmer’s bump feed system to malfunction. For this reason,
users are strongly urged to purchase the pre-wound spool.
1. The spool can hold 20 ft (6 m) of line. Remove the white
cover. Holding the loose ends of the line together with
one hand, nd the center of the line with the other hand
and hook this center loop into the groove on the spool as
shown in Fig. 10.
Fig. 12
4. Along the groove, slide the line into the hole in the spool
cover (Fig. 13).
Fig. 10
2. Wind the line following the directional arrows on the
spool housing and hook the two ends into the side
grooves (Fig. 11).
Fig. 11
Fig. 13
5. Prepare to assemble the spool into the trimmer.
Assembling the spool
NOTE: A dual-line factory wound spool (Model TRJ601ERS) is
available for easy spool replacement on the TRJ601E electric
grass trimmer. Visit www.snowjoe.com to purchase. When
using the factory wound spool, keep the protective white
cover encasing the line in place, then follow the directions
below to feed the line into the grass trimmer.
1. Insert the spring into the shroud and thread the line into
the hole as shown in Fig. 14.
3. Firmly place the white cover on the spool and pull the
two ends approximately 3.5 inch (9 cm) out of the spool
(Fig. 12).
Fig. 14
Spring
7
2. Place the spool cover on the spool and press it rmly
down until the locking devices of the spool cover securely
click into place (Fig. 15).
Fig. 15
Spool cover
Locking
devices
Operation
The Electric Grass Trimmer/Edger is designed to cut grass
and weeds under bushes, and on slopes and edges that
cannot be reached with the lawn mower. The trimmer must
be used outdoors only, at an ambient temperature between
0ºC and 45ºC.
mWARNING! Remove stones, loose pieces of wood
and other objects from the cutting area. The blade continues
to rotate for a few seconds after the trimmer is switched off.
Let the motor come to a complete stop before switching the
trimmer back on. Do not rapidly switch the trimmer off and on.
Spool
Check length of nylon cutting line
1. Pull the line to the inner edge of the outer safety guard. If
the line is too short (i.e. less than 50 mm from the inside
edge of the safety guard), push down on the center of
the trimmer head and simultaneously pull the line a few
centimeters past the edge of the safety guard (Fig. 16).
Fig. 16
Spool
Center of trimmer head
Outer guard
ON/OFF switch
1. To switch the grass trimmer ON, press and hold the safety
button, then squeeze the ON/OFF trigger and release the
safety button.
2. To switch OFF, release the ON/OFF trigger.
Cutting grass
1. Move the grass trimmer left and right, keeping it a safe
distance away from the body. The trimmer can efciently
cut grass up to a height of 6 in. (15 cm). Cut higher grass
in stages.
2. When using the trimmer, hold it at an angle of about 20°
to the ground (Fig. 17) and swing the trimmer from side to
side (Fig. 18).
Fig. 17
To increase line length
NOTE: The grass trimmer comes with a full line spool. The line
wears down during work. To feed in new line:
1. Switch the machine on and press the head of the spool
rmly against the ground.
2. The line will automatically be released by centrifugal force.
The trimmer line will be cut to the right length by the blade
on the spool cover.
20°
8
Fig. 18
mWARNING! Do not overload the trimmer – Cut in
small sections to maximize the trimmer’s efciency and keep
the trimmer running at high speed (Fig. 19).
Fig. 19
X
Trimming edges
1. Guide the grass trimmer along the edge of the lawn. Avoid
contact with paved surfaces, stone or garden walls, as this
will wear the line rapidly.
2. Use the edge of the guard as a guide when cutting near
fences and walls (Fig. 20).
3. Move the trimmer in a backwards direction when trimming
around edges to avoid damage.
Maintenance
m
WARNING! Before performing any maintenance task,
cut off the electric power supply by disconnecting the plug
from the extension cord.
mWARNING! Always wear protective gloves during
maintenance tasks. Do not carry out maintenance when the
engine is running or hot.
mWARNING! Use only original manufacturer’s
replacement parts, accessories and attachments. Failure to do
so can cause potential injury and poor performance.
• Before conducting any maintenance task, make sure the
trimmer is unplugged.
• Only the maintenance operations described in this manual
may be carried out by the user. For repairs that have not
been explained in these instructions, contact an authorized
service center.
• Check all screws regularly to ensure that they are tightly
secured.
• Only use original replacement parts. These spare parts are
designed specically for this device and are the only ones
suitable for replacement. Other replacement parts will not
only lead to an invalidation of the warranty, but also may
endanger you and your environment.
• Do not spray or wet the appliance with water.
• Do not use detergents or solvents as these could ruin
the trimmer. The plastic parts can be easily damaged by
chemical agents.
• If the cutting blade no longer cuts or breaks, replace it by
contacting an authorized service center.
IMPORTANT:
To ensure product safety and reliability, repairs, maintenance
and adjustments should be performed by authorized service
centers or other qualied service organizations that utilize
identical replacement parts for their repairs.
Fig. 20
Storage
Follow these recommendations for storing the grass trimmer.
• Clean the grass trimmer thoroughly before storing.
• Store the trimmer in a stable and safe position out of the
reach of children. Keep the trimmer in a dry place where the
temperature is not too hot or too cold.
• Do not store the grass trimmer resting against the oor.
Hang it by the upper handgrip so that the guard does not
touch anything. If the guard rests against a surface, its
shape and dimensions could be permanently altered, and
could render the machine unsafe to use.
9
Troubleshooting
Problems Possible Cause Possible Solution
The motor does not
run or the tool runs
slowly.
Bump line feed does
not work.
• Power failure/unit not plugged
into a working receptacle.
• Spool housing cannot rotate freely.
• Cutting line does not protrude.
• Trimming blade bound with
accumulated grass.
• Bump feed out of line.
• Spool bound up.
• Bump feed is dirty.
• Spool line twisted when relled.
• Not enough line is exposed.
• Check to make sure the unit is plugged into a working
outlet. Make sure the extension cord is not damaged.
• Remove the spool and clean the slots; carefully remove
any grass and weeds or other debris.
• Cut the spool line off so that it just reaches the line
trimming blade.
• Take the trimmer to an authorized service center if the
trimmer does not start after completing these checks.
• Stop the machine and clean the trimming blade.
• Install a new spool of cutting line.
• Clean the bump feed.
• Remove the spool cover and pull the cutting line until it
reaches the trimming blade.
Service and Support
If your Electric Grass Trimmer/Edger requires service or maintenance, please call 1-866-766-9563 for assistance.
Model and Serial Numbers
When contacting the company or reordering parts, you will need to provide the model and serial numbers of your product.
These are found on the decal afxed to the housing or guard of your Electric Grass Trimmer/Edger. Copy these numbers into the
space provided below.
Record the following numbers from the housing or handle of your
new product:
Model #:
T R J 6 0 1 E R M
Serial #:
10
NOTES
11
A One-Year Full Warranty
for residential use
in the United States and Canada
General Conditions:
Snow Joe®, LLC warrants this product to the original purchaser for one year against defects in material or workmanship when used
for normal residential purposes. Snow Joe
part, subject to the conditions, limitations, and exclusions set forth herein. Such repair or parts replacement will be free from charge to
the original purchaser except noted below.
The duration of the warranty applies only if the product is put to personal use around the household or residence. If the product is put
to any business use, commercial or industrial, then the duration of this warranty is 90 days from the date of original purchase. If any
product is rented or leased, the duration of the warranty is 90 days from the date of original purchase.
It is the owner’s responsibility to perform correctly all maintenance, and minor adjustments explained in the owner’s manual.
Electric Products:
To obtain a replacement electric powered unit or repair the existing electric powered unit, you must return the complete unit and
postage prepaid to: Snow Joe Return Center, 86 Executive Avenue, Edison, NJ 08817.
Gasoline / Battery Products:
Limitations
• Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis. Rechargeable batteries
will be replaced free from charge during the rst 90 days. After the initial 90 days, batteries will be replaced at a prorated cost to
the customer.
• Idlers, cables, and electrical components are warranted to the original purchaser for use at household or residence for a period
of one year.
®
, LLC will repair any defect in material or workmanship, and repair or replace any defective
Exclusions
®
• Snow Joe
brand engines are covered under this warranty. All other engines and engine accessories are covered only by the
engine manufacturer’s warranty and are not covered by this warranty.
®
• Parts used that are not genuine Snow Joe
parts are not covered by this warranty.
• Damages resulting from misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires repair
is not covered under this warranty.
• Belts, augers, and tines are not covered under warranty – belts, augers, and tines wear out and can be purchased at
www.snowjoe.com or by calling 1-866-766-9563.
®
Snow Joe
obligating Snow Joe
, LLC may from time to time change the design of its products. Nothing contained in this warranty shall be construed as
®
, LLC to incorporate such design changes into previously manufactured products, nor shall such changes be
construed as an admission that previous designs were defective.
®
This warranty is intended to cover product defects only. Snow Joe
®
in connection with the use of the Snow Joe
Products covered by this warranty. This warranty does not cover any cost or expense
, LLC is not liable for indirect, incidental, or consequential damages
incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this
product, while waiting for completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential
damages, so the above exclusions may not apply in all states. This warranty may give you specic legal rights in your state.
®
If you wish to contact Snow Joe
, please direct inquiries to the:
Customer Service Department
Snow Joe Center
86 Executive Avenue
Edison, NJ 08817
®
Customers who have purchased Snow Joe
products exported from the United States and Canada should contact their Snow Joe®
Distributor (Dealer) to obtain information applicable for your country, province, or state. If for any reason, you are not satised with the
®
distributor’s service, or if you have difculty obtaining warranty information, contact your Snow Joe
®
are unsatisfactory, please write to the Snow Joe
Center at the above address.
seller. If in the event your efforts
If you have any questions about your product warranty, please call 1-866-SNOW-JOE or visit us online at www.snowjoe.com.
12
Loading...