All Operators Must Read These
Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
WARNING! This appliance is not intended for use
m
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe
call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® customer service center at
®
+ Sun Joe® dealer or
mWARNING!When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
• Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with
the controls.
• Keep bystanders away – All visitors and pets should be
kept a safe distance away from the work area.
• Use the right product – Do not use this machine for any
job except that for which it is intended.
• Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber
gloves and non-slip footwear are recommended when
working outdoors.
•
mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and
improve your footing on slippery surfaces.
Form No. SJ-SPX3001-880E-MR1
OPERATOR’S MANUAL
• Stay alert – Watch what you are doing. Use common
sense. Do not operate the pressure washer when you are
tired, or under the inuence of alcohol or drugs.
• Do not overreach –
all times.
• Avoid unintentional starting – Do not carry a plugged-
in machine with your nger on the trigger. Make sure the
switch is o before plugging in the machine.
• Do not abuse the cord – Never carry the machine by the
cord or yank the cord to disconnect it from the receptacle.
Keep the cord away from heat, oil, and sharp edges.
• Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
• Check the water temperature – This pressure washer is
not meant to pump hot water. NEVER connect it to a hot
water supply as it will signicantly reduce the life of the
pump.
• Store indoors – NEVER store the pressure washer
outdoors or where it could freeze. The pump could be
seriously damaged.
should be provided on the circuits or outlets to be used
for this pressure washer. Receptacles are available having
built-in GFCI protection and may be used for this measure
of safety.
• Inspect electrical cables – The insulation of the power
cord should be perfectly intact. If the power cord is
damaged or shows any signs of wear or tear, do not use the
pressure washer. Contact your authorized Snow Joe
Sun Joe
service center at 1-866-SNOWJOE (1-866-766-9563).
®
dealer or call the Snow Joe® + Sun Joe® customer
Keep proper footing and balance at
®
+
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use with cleaning agents that are recommended by the
manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
persons unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
• Risk of explosion – Do not spray ammable liquids.
• Disconnect the tool – Disconnect from the electrical power
supply before performing any maintenance task.
• Keep children away – This high-pressure electric
power washer must not be used by children or untrained
personnel.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by the
manufacturer.
mWARNING! Water that has owed through backow
preventers is considered to be non-potable.
mWARNING! During cleaning, maintenance or when
replacing parts, the machine must be disconnected from its
power source by removing the plug from the socket outlet.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the appliance.
Use only hoses, ttings, and couplings recommended by the
manufacturer.
• Check for damaged parts – Do not use the appliance if
the supply cord or other important parts of the appliance
are damaged (e.g. safety devices, high-pressure hoses,
trigger gun).
mWARNING! If an extension cord is used, the plug and
socket must be of watertight construction.
mWARNING! Inadequate extension cords can be
dangerous.
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
mWARNING! Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and o the
ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of
the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs,
rinse with an abundance of clean water.)
®
+ Sun Joe® customer service center at
Electrical Safety
ATTENTION: If there are problems with the electrical
MAINS, short voltage drops may appear when starting the
equipment. This can, in turn, inuence other equipment
(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax
< 0.335 OHM, such disturbances are not expected. (If you
require assistance, contact your local supply authority for
further information.)
mWARNING!Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If
you nd any, do not start up your machine and contact your
distributor.
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a
qualied person.
• The electric supply to this appliance should include either
a residual current device that will interrupt the supply if the
leakage current to the earth exceeds 30 mA for 30 ms or a
device that will interrupt the earth circuit (GFCI).
IMPORTANT: Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional lter should be installed.
Safety devices
The unloader valve can reduce pressure if it exceeds preset
values. The spray gun features a locking device. When the lock
is activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor
against overloading. The machine will restart after a few
minutes when the thermal sensor has cooled.
2. Double insulation – In a double-insulated appliance, two
systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added
to the appliance. Servicing a double-insulated appliance
requires extreme care and knowledge of the system, and
should be performed only by qualied service personnel at
an authorized Snow Joe
parts for a double-insulated appliance must be identical
to the parts they replace. A double-insulated appliance
is marked with the words “Double Insulation” or “Double
Insulated.” The symbol
also be marked on the appliance.
3. Ground fault circuit interrupter (GFCI) protection – A
GFCI should be provided on the circuit(s) or outlet(s) to be
used for the pressure washer. Receptacles are available
having built-in GFCI protection and may be used for this
measure of safety.
4. It is not recommended to use an extension cord with
this pressure washer. The unit comes standard with a
35 ft GFCI power cable. Using an extension cord may
cause a drop in line voltage resulting in loss of power and
overheating.
5. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
The appliance plug will t into a polarized outlet only one
way.
If the appliance plug does not t fully into the outlet,
reverse the plug. If the plug still does not t, make sure
that you are using the correct polarized wall outlet. If the
®
+ Sun Joe® dealer. Replacement
(square within a square) may
2
Page 3
plug still does not t, contact a qualied electrician to
install the proper wall outlet. Do not modify the appliance
plug, power cord receptacle, or power cord plug in any
way.
mWARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the electric pressure washer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Do not use an extension cord over 25 ft. The
pressure washer comes equipped with a 35 ft power
cable. Combined cord length must not exceed 60 ft.
Any extension cord must be 14-gauge (or heavier) to
safely power the pressure washer.
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
6. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
25 ft (7.6 m)
14
Risk of electrocution
• Inspect cord before using.
• Do not use if cord is damaged.
• Keep all connections dry and o the ground.
• Do not touch plug with wet hands.
• Keep cord away from heat and sharp edges.
• Do not spray electrical apparatus and wiring.
Risk of explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause
physical injuries to the operator and irreversible damage to
the machine.
Additional safety instructions
• High pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
Product Description
Table 1. Method of Securing Extension Cord
Cord setAppliance cord
(A) Tie cord as shown
(B) Connect plug and receptacle
7. Do not abuse the cord. Never pull the pressure washer
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and
sharp edges.
Purpose
• This high-pressure electric power washer is intended for
residential use to clean vehicles, machines, buildings,
facades, etc.
Areas of application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and
104ºF (40ºC).
• The machine consists of an assembly with a pump, which
is encased in a shock-absorbing housing. To provide the
operator with an optimal working position, the machine is
equipped with a spray wand and a non-slip handle grip,
whose shape and conguration comply with applicable
regulations.
• Do not cover or modify the spray wand or the spray nozzles
in any way.
• The high-pressure electric power washer is designed to be
used with cold or lukewarm water; higher temperatures can
damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as these could impair operation and
shorten the life of the machine.
3
Page 4
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
SymbolsSymbolsDescriptionsDescriptions
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
WARNING! Electrical shock hazard.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
Wear safety gloves during
use to protect hands.
Store indoors. Never store the
pressure washer outdoors.
If the pump freezes, permanent
damage may result.
WARNING! Do not expose the
unit to rain or wet conditions.
Keep dry.
To reduce the risk of injury, user
must keep all bystanders at least
49 ft (15 m) away.
Wear non-slip footwear that will
protect your feet and improve your
footing on slippery surfaces.
Machine not suitable for connection
to the potable water mains.
Always keep the power cable
away from heat sources, oils, or
sharp edges. Immediately remove
plug from the mains if the cable is
damaged, frayed, or entangled.
Sound power level is 96 dB(A).
WARNING! Turn the machine OFF
and disconnect it from the power
supply before inspecting, cleaning,
changing accessories, or conducting
any other maintenance task.
Double Insulation – When servicing,
use only identical replacement parts.
4
Page 5
Know Your Electric Pressure Washer
Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration
below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments.
Save this manual for future reference.
1. Safety lock (Locate lock in center of trigger. Pull up and snap in place. See Fig. 12, pg. 8)
2. Trigger
3. Trigger gun
4. High-pressure hose
5. Spray wand
6. Water inlet (garden hose connection)
7. Transportation handle
8. Onboard storage for Quick-Connect nozzles
9. Hose reel
10. Hand crank
11. Power cord with GFCI
12. On/O switch
13. Detergent dial
14. High-pressure hose connection
15. Cord holder
16. Trigger gun holder
17. Removable detergent tank
18. Detergent tank holder
19. Spray wand protector
20. Wheels
21. Water outlet (high-pressure connection)
22. Garden hose adaptor (female coupler)
23. Needle clean out tool
24. 0º Quick-Connect nozzle (orange)
25. 15º Quick-Connect nozzle (yellow)
26. 25º Quick-Connect nozzle (green)
27. 40º Quick-Connect nozzle (gray)
28. Soap Quick-Connect nozzle (black)
3
4
5
6
2
22
1
7
8
9
10
11
12
13
21
0º
15º
25º
23
40º
SOAP
2425262728
14
15
16
17
18
19
20
Technical Data
Rated Voltage 120 V ~ 60 Hz
Motor 14.5 amp (1800 W)
Max. Water Inlet Temperature 104ºF/40ºC
Max. Water Inlet Pressure 0.7 MPa
Max. Rated Flow 1.76 GPM
Rated Pressure 1450 PSI
Max. Pressure 2030 PSI
Hose Length 20 ft (6 m)
Power Cord Length 35 ft (10.7 m)
Weight 32 lbs (14.5 kg)
5
Page 6
Unpacking
Assembly
Carton Contents
• Pressure washer unit
• Handle
• Trigger gun
• Spray wand
• Five (5) Quick-Connect nozzles (0º, 15º, 25º, 40º and Soap)
• Removable detergent tank
• Two (2) small screws
• Spray wand protector
• Trigger gun holder
• Hose holder
• Needle clean out tool
• High-pressure hose
• Garden hose adaptor (female coupler) with two sealing rings
• Manual with registration card
1. Carefully remove the pressure washer and check to see
that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric
pressure washer. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
®
+ Sun Joe® customer service center at
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
1. Position the washer as CLOSE as possible to the
water supply.
2. The washer must be used on a secure and stable surface
in a standing, upright position (Fig. 1).
Fig. 1
3. Slide the trigger gun holder into position and secure it in
place with one screw (Fig. 2).
Fig. 2
Screw
Trigger gun holder
4. Insert the detergent bottle (bottom end rst) into its
storage compartment (Fig 3). Then insert the suction tube
with lter into the bottle and close it with the cap (Fig. 4).
Fig. 3
6
Detergent
bottle
Page 7
Fig. 4
7. Connect the high-pressure hose to the trigger gun
(Fig. 7).
Suctiontubewithlter
5. To assemble the spray wand protector, rst snap the tabs
into the slots located at the bottom left side of the unit,
and then secure it in place with the other screw (Fig. 5).
Fig. 5
Spray wand protector
Screw
Fig. 7
High-pressure hose
Trigger gun
mWARNING! Keep hose away from sharp objects.
Bursting hoses may cause injury. Examine hoses regularly and
replace if damaged. Do not attempt to mend a damaged hose.
8. Connect the garden hose adaptor (female coupler) to
the water inlet of the pressure washer, then thread your
garden hose (male end) into the garden hose adaptor
(Fig. 8). The garden hose must have an internal diameter
of at least 13 mm (1/2 in.) and must be reinforced. The
water supply must be at least equal to the washer delivery
capacity.
NOTE: The machine is not suitable for connection to a
potable water main.
6. Fit the spray wand into the trigger gun and rotate it until
the two parts are completely locked (Fig. 6).
Fig. 6
Trigger gun
Spray wand
7
Garden hose
(male end)
Fig. 8
This end to the
water inlet on
the unit
Garden hose
(FRONT)
Water inlet
(female coupler)
Page 8
9. Attach garden hose to water supply (Fig. 9).
OFF/O
ON/I
Fig. 9
Connect to water supply
Garden hose
mWARNING! The intake water temperature must not
exceed 104ºF/40ºC. The water supply must not exceed
0.7 MPa.
mCAUTION! The washer must only be used with clean
water; use of unltered water containing corrosive
chemicals will damage the washer.
10. Make sure the motor switch is pushed to the OFF (0)
position before plugging the unit into the power outlet
(Fig. 10).
NOTE: The GFCI may need to be reset when rst plugged
into the electric outlet. Press the "Reset" button until the
power light indicator on the GFCI illuminates.
Operation
IMPORTANT! This pressure washer is equipped with
m
a micro-switch sensitive to water ow. This Total Stop System
(TSS) senses water ow in the pump. When the trigger is
released, water stops owing through the pump. The TSS then
automatically turns the motor o to protect the pump from
overheating, thus saving energy and prolonging pump life.
1. Turn the water supply tap on completely.
2. Make sure the safety lock is down and in its original
position (Fig. 12), then press the trigger for a few seconds
until water ow is steady. This will allow air to escape and
discharge any residual pressure in the hose.
Fig. 12
Slot
Fig. 10
11. Check that the electrical supply voltage and frequency
(Volt/Hz) correspond to those specied on the pressure
washer rating plate. If the power supply is correct, you
may now plug the pressure washer into the power outlet
(Fig. 11).
Fig. 11
Reset
RESET
Power light
indicator
TEST
GFCI
Safety lock
Trigger
3. Turn the switch to the ON (I) position to start the pressure
washer (Fig. 13).
Fig. 13
OFF/O
ON/I
8
Page 9
Using the nozzles
Before beginning any cleaning task, determine the best nozzle
for the job. Each of the nozzles has a dierent spray pattern.
The nozzle patterns are 40˚ (for gentle cleaning), 25˚ (for
all-purpose cleaning), 15˚ (for tough jobs), 0˚ (for spot cleaning
or hard-to-reach areas) and the Soap nozzle (for detergent
application).
mCAUTION! NEVER change nozzles without locking the
safety lock on the trigger handle.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
This electric pressure washer is equipped with ve (5)
Quick-Connect nozzles that easily snap onto the
Quick-Connect collar of the spray wand.
To connect a nozzle to the spray wand:
1. Turn o the pressure washer and shut o the water supply.
Pull the trigger to release water pressure.
2. Engage the safety lock on the trigger handle by pushing
up on the safety lock until it clicks into the slot (Fig. 14).
Fig. 14
To disconnect a nozzle from the spray wand once the cleaning
job is complete:
4. Turn o the pressure washer and shut o the water supply.
Pull the trigger to release water pressure.
5. Engage the safety lock on the trigger handle by pushing
up on the safety lock until it clicks into the slot (Fig. 14).
6. Remove the nozzle by placing your hand over the nozzle
while pulling back on the Quick-Connect collar.
mWARNING! Do not make changes to the nozzle while
the trigger is engaged. Doing so could result in damage to the
pressure washer or injury to the user.
Working with detergents
When cleaning with the pressure washer, some cleaning tasks
can be solved with water alone, but for most tasks cleaning
with detergent allows for more eective dirt removal.
mWARNING! Use only detergents designed for
Pressure Washers. DO NOT USE household detergents, acids,
alkaline solutions, bleaches, solvents, ammable material, or
industrial grade solutions. These could damage the pressure
washer. Many detergents may require mixing prior to use.
Prepare the cleaning solution as instructed on the solution
bottle.
1. Remove the cap and detergent suction tube from the
detergent bottle.
2. Gently pull the onboard detergent tank out of its storage
position and ll it with detergent designed specically for
use with pressure washers (Fig. 16).
Slot
Safety lock
3. Snap the desired nozzle onto the Quick-Connect collar
until it clicks into place (Fig. 15).
Fig. 15
Spray wand
Nozzle
“Click”
Quick-Connect collar
Fig. 16
Pressure washer
detergent
Detergent tank
3. Insert the suction tube back into the tank and cap the tank
closed. Push the tank back into storage position on the
unit.
4. Install the Soap nozzle (black) on the spray wand (Fig. 15).
mCAUTION! Always test the detergent in an
inconspicuous area before use.
5. Turn on the pressure washer. Pull the trigger to operate the
unit. The liquid detergent will automatically mix with water
and be discharged through the nozzle.
9
Page 10
6. Turn the detergent dial to adjust the suction volume of the
OFF/O
I/ON
detergent solution (Fig. 17).
Fig. 17
5. Select the right nozzle for the job (Fig. 18):
Fig. 18
Detergent dial
7. Apply detergent from the bottom to the top of the dry
surface to be cleaned.
NOTE: Wetting the surface rst is not recommended as it
dilutes the detergent and reduces its cleaning ability.
8. Allow the detergent to remain on the surface for a short
time before rinsing. Do not allow the detergent to dry on
the surface.
mCAUTION! Damage may occur to painted surfaces if
the detergent is allowed to dry on the surface. Wash and rinse
a small section at a time. Avoid working on hot surfaces or in
direct sunlight.
9. When you have nished using the detergent injection
system, remove the detergent suction tube from the
detergent bottle and insert it into 1.3 gal (5 L) of fresh
water. Siphon water at low-pressure for one minute so that
all the detergent is ushed through the system. Remove
the detergent bottle and rinse it until it is thoroughly
cleaned.
mCAUTION! Failure to follow these cleaning instructions
will cause the injection system to become clogged and
inoperable.
Rinsing with the pressure washer
1. Turn o the pressure washer and shut o the water supply.
2. Pull the trigger to release water pressure.
3. Engage the safety lock on the trigger handle by pushing
4. Remove the nozzle by placing your hand over the nozzle
up on the safety lock until it clicks into the slot (Fig. 14).
while pulling back on the Quick-Connect collar.
0º
15º
i) The 0º intense-jet nozzle (orange) is an extremely
powerful nozzle that delivers a high-pressure, pencilpoint jet stream. It is used to cut heavy dirt deposits
in a small, concentrated area. It is ideal for dissolving
stubborn substances, like tar and grease spots on
concrete, or for removing caked mud from equipment.
Use this nozzle to clean hard-to-reach areas including
the facades of 2-story buildings or the undersides of
lawn mowers and tractors.
NOTE: Care should be used when choosing the
right nozzle to avoid permanently gouging wood or
damaging fragile surfaces.
ii) Use the 15º fan-tip nozzle (yellow) for intense cleaning
jobs on hard surfaces. Applications include stripping
paint, removing oil stains, grease, heavy mildew stains,
and rust from steel. This nozzle should only be used in
areas that can withstand the high-pressure from this
nozzle.
iii) Use the 25º fan-tip nozzle (green) to clean home siding,
brick patios, wood decks, driveways, or sidewalks.
When using this nozzle, test a small area rst to avoid
surface damage.
iv) Use the 40º wide-spray tip nozzle (gray) to clean items
such as cars, trucks, boats, patio furniture, or lawn
equipment.
v) Use the Soap nozzle (black) for low-pressure detergent
application to clean equipment, remove mildew and
oxidation stains from houses, clean bricks or degrease
grimy surfaces.
NOTE: When using detergent, make sure that the
correct Soap nozzle (black) is installed. All of the other
colored nozzles will not work for detergent application.
6. Start at the top of the area to be rinsed and work down,
making sure to overlap the strokes.
25º
40º
SOAP
mIMPORTANT! NEVER USE:
• Bleach, chlorine products, and other corrosive chemicals
These chemicals will harm the unit and will damage
the cleaning surface.
Shutting down
1. Turn the switch to the OFF (0) position and unplug the
power cord from the outlet.
2. Turn o the water source.
3. Hold the trigger to release water pressure.
4. Disconnect the garden hose from the water inlet on
the unit.
5. Disconnect the high-pressure hose connection on the
trigger gun handle.
6. Release the trigger and engage the gun safety lock.
mWARNING! Turn o the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in
personal injury due to discharge of high-pressure water.
Taking a break
If you are taking a break of ve minutes or more between
cleaning tasks:
1. Engage the gun safety lock.
2. Turn the switch to the OFF (0) position.
3. Unplug the power cord from the outlet.
Storage
Hose reel
1. Unlock the hose reel by pulling out on the handle out
(Fig. 19).
2. Turn the handle counterclockwise to wind the hose
(Fig. 20).
Fig. 20
Hose reel handle
3. Wind the hose until you reach the hose's end.
4. Push the handle in to lock the reel.
mCAUTION! Always store your pressure washer in a
location where the temperature will not fall below 32ºF (0ºC).
The pump in this machine is susceptible to permanent damage
if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
• Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
• It is important to store this product in a frost-free area.
• Always empty water from all hoses, the pump, and the
detergent bottle before storing.
mCAUTION! The use of a pump protector is
recommended to prevent cold weather damage during storage
over the winter months.
Fig. 19
Hose reel handle
Winterizing and long-term storage
If you must store your pressure washer in a location where
the temperature falls below 32ºF (0ºC), you can minimize the
chance of damage to your machine by utilizing the following
procedure:
• Disconnect all water connections.
• Turn on the machine for a few seconds until the remaining
water in the pump exits. Turn o immediately.
• Do not allow the high-pressure hose to become kinked.
• Store the machine and accessories in a room that does
not reach freezing temperatures.
• Do not store near a furnace or other sources of heat that
may dry out the pump seals.
• Operate the pressure washer with non-corrosive/non-toxic
anti-freeze, a pump saver, or a pump protector before
storing for the winter.
11
Page 12
mWARNING! Before reusing, completely ush the unit
out with clear water. Anti-freeze products can damage
paintwork, so you must ensure there is no anti-freeze left in the
system before using it again.
Maintenance
CAUTION! Before working on the pressure washer,
m
disconnect the plug from the power supply socket.
1. To ensure good performance, check and clean the water
inlet lter (Fig. 21). Remove the lter and rinse with warm
water to prevent any foreign matter from clogging the
pump (Fig. 22).
Fig. 21
2. Clean the nozzle with the needle clean out tool provided
(Fig. 23). Remove the spray wand from the gun; remove
any dirt from the nozzle hole and rinse.
Fig. 23
15º
Needle clean out tool
Fig. 22
(FRONT)
Waterinletlter
Garden hose adaptor
Inletlter
3. Remove additional debris by back ushing water through
the nozzle and spray wand. To do this, place the end of
your garden hose (with water running) to the tip of the
nozzle, pushing water and debris out of the back opening
of the nozzle and spray wand.
Circuit Diagram
A circuit diagram for the pressure washer is provided below for
your reference (Fig. 24).
Fig. 24
Micro-switch
Power cord
Motor
On/off switch
Capacitor
Disposal
Recycling the washer
• Do not dispose of electrical appliances as unsorted
municipal waste. Use separate collection facilities.
• Contact your local government agency for information
regarding the collection systems available.
• If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your
health and well-being.
12
Page 13
• When replacing old appliances with new ones, the retailer
is legally obligated to take back your old appliance for
disposal at least free of charge.
Service and Support
If your Sun Joe® Pressure Joe SPX3001 electric pressure
washer requires service or maintenance, please call the
Snow Joe
1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® customer service center at
Model and Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
Record the following numbers from the housing or handle of your
new product:
Model #:
S P X 3 0 0 1
Serial #:
13
Page 14
Troubleshooting
• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that its
parts are in proper working order.
• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.
Problems Possible Cause Possible Solution
Machine refuses
to start
Fluctuating pressure
Machine stops
Fuse blows
• Power failure/machine not
plugged into a working receptacle.
• Defective socket.
• Fuse has blown.
• Defective extension cord.
• Pump sucking air.
• Valves dirty, worn out, or stuck.
• Pump seals worn out.
• Fuse has blown.
• Incorrect mains voltage.
• Thermal sensor activated.
• Nozzle partially blocked.
• Fuse too small.
• Check to make sure machine is plugged into
a working outlet.
• Check the power cord and reset the GFCI.
Try a dierent outlet.
• Replace fuse. Switch o any other machines
that are using the same circuit.
• Try the unit without an extension cord.
• Check the hoses and connections are airtight.
• Clean or replace valves/seals.
• Please call the Snow Joe
service center at 1-866-SNOWJOE (1-866-766-9563)
for assistance.
• Replace fuse. Switch o other machines using
the same circuit.
• Check that the mains voltage corresponds to
specication on the model tag.
• Leave the washer for 5 minutes to cool down.
• Clean the nozzle.
• Install a fuse with a higher amp rating than the
amp consumption of the machine. Try the unit
without an extension cord.
®
+ Sun Joe® customer
Machine pulsating
Machine often starts
and stops by itself
Machine starts, but
no water comes out
• Air in inlet hose.
• Inadequate supply of mains water.
• Nozzle partially blocked.
• Water lter blocked.
• Hose kinked.
• Pump/spray gun is leaking.
• Trigger mechanism is broken.
• Pump/hoses or accessories frozen.
• No water supply.
• Water inlet lter blocked.
• Nozzle blocked.
14
• Allow machine to run by holding the trigger until
regular working pressure resumes.
• Check that the water supply corresponds to the
specications required.
• WARNING! Avoid using long, thin hoses
(minimum 1/2 in. diameter).
• Clean the nozzle.
• Clean the water inlet lter.
• Straighten out the hose to remove any kinks/blockages.
• Please call Snow Joe
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
• Wait for pump/hoses or accessories to thaw.
• Connect inlet water.
• Clean the water inlet lter.
• Clean the nozzle.
®
+ Sun Joe® customer service
Page 15
Accessories
WARNING! ALWAYS use only authorized Snow Joe
m
replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe
®
+ Sun Joe® replacement parts and accessories. NEVER use
®
+ Sun Joe®
if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any
other attachment or accessory can be dangerous and could cause injury or mechanical damage.
ModelAccessoriesItem
1
0
º
1
5
º
SPX3000 Series Spray Tip Set – Fits
SPX3000 + SPX3001 Pressure Washer Models
2
5
º
4
0
º
SO
A
P
2
25-Foot Extension Hose for SPX
Pressure Washer Series
SPX3000-TPS
SPX-25H
3
Dual Swivel Brass Connector –
3/4-In. by 3/4-In. Garden Hose to Pipe End
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe
®
+ Sun Joe® to provide notice of such
changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe
service center at 1-866-SNOWJOE (1-866-766-9563).
SPX-BSC
®
+ Sun Joe® customer
15
Page 16
NOTES
16
Page 17
NOTES
17
Page 18
NOTES
18
Page 19
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience
as pleasant as possible. Unfortunately, there are times when a product does not work or breaks under normal
operating conditions. We think it’s important that you know what you can expect from us. That’s why we created
the Snow Joe® + Sun Joe® promise.
OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase. If your product does not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or
by sending you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in
action cutting, sawing, mowing, washing and…?
GENERAL CONDITIONS:
®
Snow Joe
+ Sun Joe® operating under Snow Joe®, LLC warrants
this new product to the original purchaser for two years against
defects in material or workmanship when used for normal
residential purposes. If a replacement part or product is needed,
it will be sent free of charge to the original purchaser except as
noted below.
The duration of this warranty applies only if the product is put
to personal use around the household. If the product is put to
any business, commercial or industrial use or is rented or leased,
then the duration of this warranty is 90 days from the date of
original purchase. It is the owner’s responsibility to correctly
perform all maintenance and minor adjustments explained in
the owner’s manual.
HOW TO OBTAIN YOUR REPLACEMENT PART OR PRODUCT:
To obtain a replacement part or product, please visit
snowjoe.com/help or email us at help@snowjoe.com for
instructions. Please be sure to register your unit beforehand to
speed up this process. Certain products may require a serial
number, typically found on the decal axed to the housing
or guard of your product. All products require a valid proof
of purchase.
EXCLUSIONS:
• Wearing parts like belts, augers, chains and tines are
not covered under this warranty. Wearing parts can be
purchased at snowjoe.com or by calling 1-866-SNOWJOE
(1-866-766-9563).
• Batteries are covered in full for 90-days from the date of
purchase.
Snow Joe® + Sun Joe® may from time to time change the design
of its products. Nothing contained in this warranty shall be
®
construed as obligating Snow Joe
+ Sun Joe® to incorporate
such design changes into previously manufactured products, nor
shall such changes be construed as an admission that previous
designs were defective.
This warranty is intended to cover product defects only.
®
Snow Joe
, LLC is not liable for indirect, incidental or
consequential damages in connection with the use or misuse of
®
the Snow Joe
+ Sun Joe® products covered by this warranty.
This warranty does not cover any cost or expense incurred
by the purchaser in providing substitute equipment or service
during reasonable periods of malfunction or non-use of this
product while waiting for a replacement part or unit under this
warranty. Some states do not allow exclusions of incidental or
consequential damages so the above exclusions may not apply
in all states. This warranty may give you specic legal rights in
your state.
HOW TO REACH US:
We’re here to help Monday through Friday from 9AM to 6PM EST.
You can reach us at 1-866-SNOWJOE (1-866-766-9563), online
at snowjoe.com, via email at help@snowjoe.com or tweet us
@snowjoe.
EXPORTS:
®
Customers who have purchased Snow Joe
+ Sun Joe®
products exported from the United States and Canada should
®
contact their Snow Joe
+ Sun Joe® distributor (dealer) to obtain
information applicable to your country, province or state. If for
any reason, you are not satised with the distributor’s service,
or if you have diculty obtaining warranty information, contact
®
your Snow Joe
+ Sun Joe® seller. If in the event your eorts are
unsatisfactory, please reach out to us directly.
19
Page 20
snowjoe.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.