Snow Joe SPX2000 User Manual

Page 1
ELECTRIC PRESSURE WASHER
1740 PSI | 1.59 GPM | 12.5 AMP
Model SPX2000
A Division of Snow Joe®, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
WARNING! This appliance is not intended for use
m
by children or by unassisted, unsupervised persons whose physical, sensory, or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe call the Snow Joe 1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® customer service center at
®
+ Sun Joe® dealer or
mWARNING! When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with the controls.
Keep bystanders away – All visitors and pets should be kept a safe distance away from the work area.
Use the right product – Do not use this machine for any job except that for which it is intended.
Dress properly – Do not wear loose clothing or jewelry. They can get caught in moving parts. Protective rubber gloves and non-slip footwear are recommended when working outdoors.
mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.
Form No. SJ-SPX2000-880E-MR1
OPERATOR’S MANUAL
Stay alert – Watch what you are doing. Use common sense. Do not operate the pressure washer when you are tired, or under the inuence of alcohol or drugs.
Do not overreach –
all times.
• Avoid unintentional starting – Do not carry a plugged-
in machine with your nger on the trigger. Make sure the switch is o before plugging in the machine.
Do not abuse the cord – Never carry the machine by the
cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.
Use safety glasses – Also use safety footwear, snug- tting clothing, protective gloves, and hearing and head
protection.
Check the water temperature – This pressure washer is not meant to pump hot water. NEVER connect it to a hot
water supply as it will signicantly reduce the life of the
pump.
Store indoors – NEVER store the pressure washer outdoors or where it could freeze. The pump could be seriously damaged.
Ground Fault Circuit Interrupter (GFCI) – GFCI protection should be provided on the circuits or outlets to be used for this pressure washer. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
• Inspect electrical cables – The insulation of the power cord should be perfectly intact. If the power cord is damaged or shows any signs of wear or tear, do not use the pressure washer. Contact your authorized Snow Joe
Sun Joe service center at 1-866-SNOWJOE (1-866-766-9563).
®
dealer or call the Snow Joe® + Sun Joe® customer
Keep proper footing and balance at
®
+
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use only with cleaning agents that are recommended by the manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
other people unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
Risk of explosion – Do not spray ammable liquids.
© 2014 by Snow Joe®, LLC All rights reserved. Original instructions.
1
Page 2
Disconnect the tool – Disconnect from the electrical power supply before performing any maintenance task.
Keep children away – This high-pressure electric power washer must not be used by children or untrained personnel.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by the manufacturer.
mWARNING! Water that has owed through backow
preventers is considered to be non-potable.
mWARNING! During cleaning, maintenance, or when
replacing parts, disconnect the machine from its power source by removing the plug from the socket outlet.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the appliance.
Use only hoses, ttings, and couplings recommended by the
manufacturer.
Check for damaged parts – Do not use the appliance if the supply cord or other important parts of the appliance are damaged (e.g. safety devices, high-pressure hoses, trigger gun).
mWARNING! If an extension cord is used, the plug and
socket must be of watertight construction.
NOTE: It is not recommended to use an extension cord with this pressure washer.
mWARNING! Inadequate extension cords can be
dangerous.
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
mWARNING! Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and o the
ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe 1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs, rinse with an abundance of clean water.)
®
+ Sun Joe® customer service center at
Electrical Safety
ATTENTION: If there are problems with the electrical
MAINS, short voltage drops may appear when starting the equipment. This can, in turn, inuence other equipment (e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM, such disturbances are not expected. (If you require assistance, contact your local supply authority for further information.)
mWARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects.
If you nd any, do not start up your machine. Contact your
authorized Snow Joe + Sun Joe (1-866-766-9563).
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a
• The electric supply to this appliance should include either
®
customer service center at 1-866-SNOWJOE
qualied person.
a residual current device that will interrupt the supply if the leakage current to the earth exceeds 30 mA for 30 ms or a device that will interrupt the earth circuit (GFCI).
IMPORTANT: Only use water without any impurities.
If there is a risk of running sand into the inlet water (i.e. from
your own well), an additional lter should be installed.
Safety devices
The unloader valve can reduce pressure if it exceeds preset values. The spray gun features a locking device. When the lock is activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sensor has cooled.
2. Double insulation – In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and
should be performed only by qualied service personnel at
an authorized Snow Joe parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words “Double Insulation” or “Double Insulated.” The symbol also be marked on the appliance.
3. Ground fault circuit interrupter (GFCI) protection – A GFCI should be provided on the circuit(s) or outlet(s) to be used for this pressure washer. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.
4. It is not recommended to use an extension cord with this pressure washer. The unit comes standard with a 35 ft GFCI power cable. Using an extension cord may cause a drop in line voltage resulting in loss of power and overheating.
5. To reduce the risk of electric shock, this appliance has a polarized plug (i.e. one blade is wider than the other).
The appliance plug will t into a polarized outlet only one
way.
If the appliance plug does not t fully into the outlet,
reverse the plug. If the plug still does not t, make sure
that you are using the correct polarized wall outlet. If the
®
+ Sun Joe® dealer or call the Snow Joe®
®
+ Sun Joe® dealer. Replacement
(square within a square) may
2
Page 3
plug still does not t, contact a qualied electrician to
install the proper wall outlet. Do not modify the appliance plug, power cord receptacle, or power cord plug in any way.
• Keep all connections dry and o the ground.
Do not touch plug with wet hands.
Keep cord away from heat and sharp edges.
• Do not spray electrical apparatus and wiring.
m WARNING m
Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:
• Do not allow any part of the electric pressure washer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Do not use an extension cord over 25 ft. The
pressure washer comes equipped with a 35 ft power cable. Combined cord length must not exceed 60 ft. Any extension cord must be 14-gauge (or heavier) to safely power the pressure washer.
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
6. To prevent the appliance cord from disconnecting from the extension cord during operation, make a knot with the two cords as shown in Table 1.
Table 1. Method of Securing Extension Cord
Cord set Appliance cord
(A) Tie cord as shown
(B) Connect plug and receptacle
7. Do not abuse the cord. Never pull the pressure washer
by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.
Risk of electrocution
• Inspect cord before using.
Do not use if cord is damaged.
25 ft (7.6 m)
14
Risk of explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause physical injuries to the operator and irreversible damage to the machine.
Additional safety instructions
• High-pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
Product Description
Purpose
• This high-pressure electric power washer is intended for
residential use only. It is designed for medium-to-heavy duty cleaning jobs on cars, boats, motorcycles, RV’s, ATV’s, trailers, decks, barbecues, siding, patio furniture, lawn equipment, and more.
Areas of application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and 104ºF (40ºC).
• The machine consists of an assembly with a pump, which
is encased in a shock-absorbing housing. To provide the operator with an optimal working position, the machine is equipped with a spray wand and a non-slip handle grip,
whose shape and conguration comply with applicable
regulations.
• Do not cover or modify the spray wand or the spray nozzle
in any way.
• The high-pressure electric power washer is designed to be
used with cold or lukewarm water; higher temperatures can damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as such impurities could impair operation and shorten the life of the machine.
3
Page 4
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.
Symbols SymbolsDescriptions Descriptions
READ THE OPERATOR'S MANUAL(S) – Read, understand,
and follow all instructions in the user manual(s) before attempting to assemble and operate.
WARNING! Electrical shock hazard.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING PROTECTION – For protection
against injury, wear ear defenders and safety goggles.
Wear safety gloves during use to protect hands.
Store indoors. Never store the pressure washer outdoors. If the pump freezes, permanent damage may result.
WARNING! Do not expose the unit to rain or wet conditions. Keep dry.
To reduce the risk of injury, user must keep all bystanders at least 49 ft (15 m) away.
Wear non-slip footwear that will protect your feet and improve your footing on slippery surfaces.
Machine not suitable for connection to the potable water mains.
Always keep the power cable away from heat sources, oils, or sharp edges. Immediately remove plug from the mains if the cable is damaged, frayed, or entangled.
Sound power level is 96 dB(A).
WARNING! Turn the machine OFF and disconnect it from the power supply before inspecting, cleaning, changing accessories, or conducting any other maintenance task.
Double Insulation – When servicing, use only identical replacement parts.
4
Page 5
Know Your Electric Pressure Washer
Read the owner’s manual and safety rules carefully before operating the pressure washer. Compare the illustration below to the pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
1. Safety lock
2. Trigger
3. Transport handle
4. High-pressure hose connection
5. Trigger gun
6. On/O switch
7. Adjustable spray wand
8. Water outlet (high-pressure hose connection)
9. Adjustable spray wand nozzle
10. High-pressure hose
11. Garden hose adaptor (female coupler)
12. Needle clean-out tool
13. Removable detergent tank
14. Hose holder
15. Power cord with GFCI
16. Cord holder
17. Detergent tube
18. Trigger gun holder
19. Wheels
20. Water inlet (garden hose connection)
4
5
6
1 2 3
13
17
14
16
18
7
8
9
10
11
12
Technical Data
Rated Voltage 120 V ~ 60 Hz
Motor 12.5 amp (1500 W)
Max. Water Inlet Temperature 104ºF/40ºC
Max. Water Inlet Pressure 0.7 MPa
Max. Rated Flow 1.59 GPM
15
20
(FRONT) (REAR)
Rated Pressure 1160 PSI
Max. Pressure 1740 PSI
Hose Length 20 ft (6 m)
Power Cord Length 35 ft (10.7 m)
Weight 17.4 lbs (7.9 kg)
5
19
Page 6
Unpacking
Assembly
Carton Contents
Electric pressure washer
Handle
Trigger gun
• Adjustable spray wand
• Detergent tank with cap and PVC tube
• Two (2) large Phillips head screws (for handle)
• Two (2) small Phillips head screws (for hose holder)
Hose holder
Needle clean-out tool (included with manual packet)
High-pressure hose
• Garden hose adaptor (female coupler) with two O-rings
Manual with registration card
1. Carefully remove the pressure washer and check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric pressure washer. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.
IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a
suocation risk!
®
+ Sun Joe® customer service center at
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
Tools required: Phillips head screwdriver
1. Following the alignment grooves at the top of the machine body, slide the handle into position from the front to the back, so that the solid side of the handle faces the front of the washer. Secure the handle using a Phillips head screwdriver and the two (2) large screws (Fig. 1).
Fig. 1
Handle
Alignment
2 large screws
2. Fit the cap with the attached PVC tube (black-tipped end)
onto the detergent tank.
3. Using the notch at the top of the detergent tank as a
guide, insert the detergent tank (top end rst) under the
ridge on the underside of the handle (Fig. 2). Then snap the bottom of the tank into the V-shaped groove to secure it in place (Fig. 3).
grooves
Fig. 2
Detergent tank
Fig. 3
Detergent tank
V-shaped groove
6
Page 7
4. Run the PVC detergent tube through one of the holes located at the top of the handle and connect the tube to the detergent connection (Fig. 4).
7. Connect the silver end of the high-pressure hose to the trigger gun and twist the nut as indicated to secure the connection (Fig.7).
Fig. 4
Detergent tube
5. To assemble the hose holder, slide the holder into position
and secure it to the unit with the remaining two (2) small screws (Fig. 5).
Detergent tank
Detergent connection
Fig. 5
Hose holder
Fig. 7
High pressure hose
8. Connect the other end of the high-pressure hose to the
water outlet on the washer and twist the black rotatable end-piece as indicated to secure the connection (Fig. 8).
Fig. 8
(FRONT)
Trigger gun
2 small screws
6. Fit the spray wand into the gun and rotate it until the two
parts are completely locked (Fig. 6).
Fig. 6
High-pressure hose
High-pressure water outlet
mWARNING! Keep hose away from sharp objects.
Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose.
9. Connect the garden hose adaptor (female coupler) to the water inlet of the pressure washer, then thread your garden hose (male end) into the garden hose adaptor (Fig. 9). The garden hose must have an internal diameter of at least 13 mm (1/2 in.) and must be reinforced. The water supply must be at least equal to the washer delivery capacity.
NOTE: The machine is not suitable for connection to the
potable water main.
7
Page 8
Garden hose (male end)
This end to water inlet
(REAR)
12. Check that the electrical supply voltage and frequency
(Volt/Hz) correspond to those specied on the pressure
washer rating plate. If the power supply is correct, you may now plug the pressure washer into the power outlet (Fig. 12).
Fig. 12
Water inlet
(female coupler)
Fig. 9
10. Attach garden hose to water supply (Fig. 10).
Garden hose
Fig. 10
Connect to water supply
Garden hose
mWARNING! The intake water temperature must not
exceed 104ºF/40ºC. The water supply must not exceed
0.7 MPa.
mCAUTION! The washer must only be used with clean
water; use of unltered water containing corrosive
chemicals will damage the washer.
11. Make sure the motor switch is pushed to the OFF (0) position before plugging the unit into the power outlet (Fig. 11).
Reset
RESET
GFCI
TEST
Power light indicator
NOTE: The GFCI may need to be reset when rst plugged
into the electric outlet. Press the "Reset" button until the power light indicator on the GFCI illuminates.
Operation
IMPORTANT! This pressure washer is equipped with
m
a micro-switch sensitive to water ow. This Total Stop System (TSS) senses water ow in the pump. When the trigger is released, water stops owing through the pump. The TSS then automatically turns the motor o to protect the pump from
overheating, thus saving energy and prolonging pump life.
1. Position the washer as CLOSE as possible to the water supply.
2. The washer must be used on a secure and stable surface in a standing, upright position (Fig. 13).
Fig. 13
Fig. 11
OFF
OFF
0
ON
ON
I
3. Turn the water supply tap on completely.
8
Page 9
4. Release the safety lock, then press the trigger for a few
seconds until the water ow is steady. Operating the
pressure washer in this manner will allow air to escape and discharge residual pressure in the hose (Figs. 14 and 15).
Pressure adjustment knob
Fig. 14
Safety lock
Trigger
Fig. 15
5. Keeping the trigger pressed, turn the switch to the ON (I)
position to start the pressure washer.
6. When re-starting the motor, always keep the trigger pressed.
NOTE: The motor only runs when the trigger is operated
and shuts o when the trigger is released.
Pencil spray
Nozzle tip
Nozzle tip
adjustment knob
Fan spray
Fig. 16
mWARNING! Do not adjust the nozzle while the trigger
is squeezed. Failure to do so could result in damage.
Working with detergents
When cleaning with the pressure washer, some cleaning tasks can be solved with water alone, but for most tasks cleaning
with detergent allows for more eective dirt removal.
mWARNING! To apply detergents, you must use the low
pressure setting. This setting will gently apply the detergent at a pressure equivalent to a low-set garden hose. The high-pressure setting is used for rinsing. You cannot apply detergents when working at high pressure.
mWARNING! Use only detergents specically designed
for use with pressure washers. DO NOT USE household detergents, acids, alkaline solutions, bleaches, solvents,
ammable material, or industrial grade solutions. These could
damage the pressure washer. Many detergents may require mixing prior to use. Prepare the cleaning solution as instructed
on the solution bottle.
1. Set the adjustable nozzle to the low-pressure, fan-spray setting (Fig. 17).
Fig. 17
Using the adjustable spray nozzle
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.
1. The washer is equipped with an adjustable nozzle.
2. The water pressure can be adjusted from low pressure (–)
to high pressure (+) by turning the pressure adjustment knob. The nozzle tip can be adjusted from pencil spray (wide open tip) to fan spray (narrow tip) by turning the nozzle tip adjustment knob (Fig. 16).
Open to apply detergents
9
Page 10
2. Gently pull the onboard detergent tank out of its storage
position. Remove the cap with PVC tube and ll the tank with detergent designed specically for use with pressure
washers (Fig. 18).
Fig. 18
Pressure washer detergent
Detergent tank
3. Insert the suction tube back into the tank and cap the tank
closed. Push the tank back into storage position on the unit.
mCAUTION! Always test the detergent in an
inconspicuous area before use.
4. Turn on the pressure washer. Pull the trigger to operate the unit. The liquid detergent will automatically mix with water and be discharged through the nozzle.
5 Apply detergent from the bottom to the top of the dry
surface to be cleaned.
NOTE: Wetting the surface rst is not recommended as it
dilutes the detergent and reduces its cleaning ability.
6. Allow the detergent to remain on the surface for a short time before rinsing. Do not allow the detergent to dry on the surface.
mCAUTION! Damage may occur to painted surfaces if
the detergent is allowed to dry on the surface. Wash and rinse a small section at a time. Avoid working on hot surfaces or in
direct sunlight.
7. Rinse with clean water under high pressure. When working on a vertical surface, rinse from the bottom up, then rinse from the top down to avoid streaking. Hold the nozzle 6-8 inches away from the work surface at a 45° angle.
8. When you have nished using the detergent injection
system, remove the detergent suction tube from the detergent tank and insert it into 1.3 gal (5 L) of fresh water. Siphon water at low pressure for one minute so that all
the detergent is ushed through the system. Remove the
detergent tank and rinse it until it is thoroughly cleaned.
mCAUTION! Failure to follow these cleaning instructions
will cause the injection system to become clogged and inoperable.
mIMPORTANT! NEVER USE:
Bleach, chlorine products, and other corrosive chemicals
Liquids containing solvents (e.g. paint thinners, gasoline,
oils)
Tri-sodium phosphate products
Ammonia products
Acid-based products
These chemicals will harm the unit and will damage the cleaning surface.
Shutting down
1. Turn the switch to the OFF (0) position and unplug the
power cord from the outlet.
2. Turn o the water source.
3. Hold the trigger to release water pressure.
4. Disconnect the garden hose from the water inlet on
the unit.
5. Disconnect the high-pressure hose connection on the trigger gun handle.
6. Release the trigger and engage the gun safety lock.
mWARNING! Turn o the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in personal injury due to discharge of high-pressure water.
Taking a break
If you are taking a break of ve minutes or more between cleaning tasks:
1. Engage the gun safety lock (Fig. 14).
2. Turn the switch to the OFF (0) position.
3. Unplug the power cord from the outlet.
Storage
CAUTION! Always store your pressure washer in a
m
location where the temperature will not fall below 32ºF (0ºC). The pump in this machine is susceptible to permanent damage if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
• Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
It is important to store this product in a frost-free area.
Always empty water from all hoses, the pump, and the
detergent tank before storing.
mCAUTION! The use of a pump protector is
recommended to prevent cold weather damage during storage over the winter months.
10
Page 11
Winterizing and long-term storage
If you must store your pressure washer in a location where the temperature falls below 32ºF (0ºC), you can minimize the chance of damage to your machine by utilizing the following
procedure:
Disconnect all water connections.
Turn on the machine for a few seconds until the remaining water in the pump exits. Turn o immediately.
Do not allow the high-pressure hose to become kinked.
Store the machine and accessories in a room that does
not reach freezing temperatures.
Do not store near a furnace or other sources of heat that may dry out the pump seals.
• Operate the pressure washer with non-corrosive/non-toxic
anti-freeze, a pump saver, or a pump protector before storing for the winter.
Fig. 20
Inletlter
2. Clean the nozzle with the needle clean-out tool provided (Fig. 21). Remove the spray wand from the gun; remove any dirt from the nozzle hole and rinse.
mWARNING! Before reusing, completely ush the unit
with clear water. Anti-freeze products can damage paintwork, so you must ensure there is no anti-freeze left in the system
before using it again.
Maintenance
CAUTION! Before working on the pressure washer,
m
disconnect the plug from the power supply socket.
1. To ensure good performance, check and clean the water inlet lter (Fig. 19). Remove the lter and rinse with warm water to prevent any foreign matter from clogging the pump (Fig. 20).
Fig. 19
(REAR)
Waterinletlter
Fig. 21
Needle clean-out tool
Circuit Diagram
A circuit diagram for the pressure washer is provided below for your reference (Fig. 22).
Fig. 22
Micro-switch
Power cord
Garden hose adaptor
Motor
On/off switch
Capacitor
11
Page 12
Disposal
Recycling the washer
Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities.
Contact your local government agency for information regarding the collection systems available.
• If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.
Service and Support
If your Sun Joe® Pressure Joe SPX2000 electric pressure washer requires service or maintenance, please call the Snow Joe
1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® customer service center at
Model and Serial Numbers
When contacting the company, reordering parts, or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.
Record the following numbers from the housing or handle of your new product:
Model #:
S P X 2 0 0 0
Serial #:
12
Page 13
Troubleshooting
• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that
its parts are in proper working order.
• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.
Problems Possible Cause Possible Solution
Machine refuses to start
Fluctuating pressure
Machine stops
Fuse blows
Power failure/machine not plugged into a working receptacle.
Defective socket.
Fuse has blown.
Defective extension cord.
Pump sucking air.
Valves dirty, worn out, or stuck.
Pump seals worn out.
Fuse has blown.
Incorrect mains voltage.
Thermal sensor activated.
Nozzle partially blocked.
Fuse too small.
Check to make sure machine is plugged into
a working outlet.
Check the power cord and reset the GFCI. Try a dierent outlet.
• Replace fuse. Switch o any other machines
that are using the same circuit.
• Try the unit without an extension cord.
Check the hoses and connections are airtight.
• Clean or replace valves/seals.
• Please call the Snow Joe
service center at 1-866-SNOWJOE (1-866-766-9563) for assistance.
• Replace fuse. Switch o other machines using the same circuit.
Check that the mains voltage corresponds to specication on the model tag.
Leave the washer for 5 minutes to cool down.
Clean the nozzle.
• Install a fuse with a higher amp rating than the
amp consumption of the machine. Try the unit without an extension cord.
®
+ Sun Joe® customer
Machine pulsating
Machine often starts and stops by itself
Machine starts, but no water comes out
Air in inlet hose.
Inadequate supply of mains water.
Nozzle partially blocked.
• Water lter blocked.
Hose kinked.
Pump/spray gun is leaking.
Trigger mechanism is broken.
Pump/hoses or accessories frozen.
No water supply.
• Water inlet lter blocked.
• Nozzle blocked.
13
• Allow machine to run by holding the trigger until regular working pressure resumes.
• Check that the water supply corresponds to the specications required.
WARNING! Avoid using long, thin hoses
(minimum 1/2 in. diameter).
Clean the nozzle.
• Clean the water inlet lter.
• Straighten out the hose to remove any kinks/blockages.
• Please call the Snow Joe
center at 1-866-SNOWJOE (1-866-766-9563) for assistance.
Wait for pump/hoses or accessories to thaw.
Connect inlet water.
• Clean the water inlet lter.
Clean the nozzle.
®
+ Sun Joe® customer service
Page 14
Accessories
WARNING! ALWAYS use only authorized Snow Joe
m
replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
®
+ Sun Joe® replacement parts and accessories. NEVER use
®
+ Sun Joe®
ModelAccessories Item
1
25-Foot Extension Hose for SPX Pressure Washer Series
2
Dual Swivel Brass Connector – 3/4-In. by 3/4-In. Garden Hose to Pipe End
SPX-25H
SPX-BSC
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe changes. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe service center at 1-866-SNOWJOE (1-866-766-9563).
®
+ Sun Joe® to provide notice of such
®
+ Sun Joe® customer
14
Page 15
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe® + Sun Joe® are dedicated to you, our customer. We strive to make your experience
as pleasant as possible. Unfortunately, there are times when a product does not work or breaks under normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we created the Snow Joe® + Sun Joe® promise.
OUR PROMISE: Snow Joe® + Sun Joe® warrant new products for two years from the date of purchase. If your product does not work, or there’s an issue with a specic part, we will x this by either sending you a free replacement part or by sending you a new or comparable product at no charge. How cool is that! Before you know it, you’ll be back in action cutting, sawing, mowing, washing and…?
GENERAL CONDITIONS:
®
Snow Joe
+ Sun Joe® operating under Snow Joe®, LLC warrants this new product to the original purchaser for two years against defects in material or workmanship when used for normal residential purposes. If a replacement part or product is needed, it will be sent free of charge to the original purchaser except as noted below.
The duration of this warranty applies only if the product is put to personal use around the household. If the product is put to any business, commercial or industrial use or is rented or leased, then the duration of this warranty is 90 days from the date of original purchase. It is the owner’s responsibility to correctly perform all maintenance and minor adjustments explained in the owner’s manual.
HOW TO OBTAIN YOUR REPLACEMENT PART OR PRODUCT:
To obtain a replacement part or product, please visit snowjoe.com/help or email us at help@snowjoe.com for instructions. Please be sure to register your unit beforehand to speed up this process. Certain products may require a serial
number, typically found on the decal axed to the housing
or guard of your product. All products require a valid proof of purchase.
EXCLUSIONS:
• Wearing parts like belts, augers, chains and tines are
not covered under this warranty. Wearing parts can be purchased at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
• Batteries are covered in full for 90-days from the date of
purchase.
Snow Joe® + Sun Joe® may from time to time change the design of its products. Nothing contained in this warranty shall be
®
construed as obligating Snow Joe
+ Sun Joe® to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.
This warranty is intended to cover product defects only.
®
Snow Joe
, LLC is not liable for indirect, incidental or
consequential damages in connection with the use or misuse of
®
the Snow Joe
+ Sun Joe® products covered by this warranty. This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this product while waiting for a replacement part or unit under this warranty. Some states do not allow exclusions of incidental or consequential damages so the above exclusions may not apply
in all states. This warranty may give you specic legal rights in
your state.
HOW TO REACH US:
We’re here to help Monday through Friday from 9AM to 6PM EST. You can reach us at 1-866-SNOWJOE (1-866-766-9563), online at snowjoe.com, via email at help@snowjoe.com or tweet us @snowjoe.
EXPORTS:
®
Customers who have purchased Snow Joe
+ Sun Joe®
products exported from the United States and Canada should
®
contact their Snow Joe
+ Sun Joe® distributor (dealer) to obtain
information applicable to your country, province or state. If for
any reason, you are not satised with the distributor’s service, or if you have diculty obtaining warranty information, contact
®
your Snow Joe
+ Sun Joe® seller. If in the event your eorts are
unsatisfactory, please reach out to us directly.
15
Page 16
snowjoe.com
Loading...