3 In 1 Electric Blower, Vacuum and Leaf Shredder
3 In 1 Electric Blower, Vacuum and Leaf Shredder
Model No. SBJ604ERM
A Division of Snow Joe®, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Failure to follow all warnings, and instructions may result in
electric shock, re or serious injury.
m WARNING! This indicates a hazardous situation,
which, if not avoided, could result in death or serious injury.
m CAUTION! This indicates a hazardous situation,
which, if not avoided, could result in minor or moderate injury.
m DANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
When using an electric appliance, basic
precaution should always be followed,
including the following safety warnings.
General Power Tool Safety Warnings
FOR HOUSEHOLD USE ONLY
m WARNING! To reduce the risk of re, electric shock,
or injury:
1. Do not leave appliance when plugged in. Unplug from
outlet when not in use and before servicing.
2. Do not use on wet surfaces.
3. Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
4. Use only as described in this manual. Use only
manufacturer’s recommended attachments.
5. Do not use with damaged cord or plug. If appliance is
not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to a
service center.
6. Do not pull or carry by cord, or use cord as a handle.
Do not close a door on cord, or pull cord around sharp
edges or corners.
7. Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
8. Do not handle plug or appliance with wet hands.
Form No. SJ-SBJ604ERM-880E
OPERATOR’S MANUAL
9. Do not put any object into openings. Do not use with
any opening blocked; keep free of dust, lint, hair, and
anything that may reduce air ow.
10. Keep hair, loose clothing, ngers, and all parts of body
away from openings and moving parts.
11. Turn off all controls before unplugging.
12. Do not use to pick up ammable or combustible
liquids, such as gasoline, or use in areas where they
may be present.
13. Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
14. Do not use without dust bag and/or lters in place.
15. This appliance is provided with double insulation. Use
only indentical replacement parts. See instructions for
Servicing of Double-Insulated Appliances.
16. Look on your appliance and follow all label and
marking instructions.
17. Keep end of hose, wands and other openings away
from your face and body.
18. Always unplug this appliance before connecting or
disconnecting vacuum hose.
19. Store the appliance indoors. Put the vacuum away
after use to prevent tripping accidents.
20. Using improper voltage may result in damage to the
motor and possible injury to the user. Correct voltage is
listed on the rating label.
21. Do not use for any purpose other than described in this
user’s guide.
22. If the blower is damaged, it must be repaired by the
manufacturer or its service agent or a similarly qualied
person in order to avoid a hazard.
23. Do not run appliance over cord. Keep cord away from
heated surfaces.
24. Do not use for wet material.
25. Disconnect before cleaning or changing accessories.
© 2013 by Snow Joe, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
m WARNING! To reduce the risk of electric shock, this
appliance has a polarized plug (one blade is wider than the
other). This plug will t in a polarized outlet only one way. If the
plug does not t fully in the outlet, reverse the plug. If it still
does not t, contact a qualied electrician to install the proper
outlet. Do not change the plug in any way.
m WARNING! To reduce the risk of electric shock –
Unplug before cleaning or servicing.
To reduce the risk of electric shock - Do not expose unit to
water or operate unit on wet ground. Disconnect from supply
circuit before opening.
• Disconnect before cleaning or changing accessories.
• Do not use for wet material.
m CAUTION! To reduce the risk of injury from moving
parts-Unplug before servicing.
Servicing of double-insulated appliances
A double-insulated appliance is marked with one or more
of the following : The words “DOUBLE INSULATION” or
“DOUBLE INSULATED” or the double insulation symbol ( ).
In a double-insulated appliance, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated appliance, nor should a means
for grounding be added to the appliance. Servicing a doubleinsulated appliance requires extreme care and knowledge
of the system, and should be done only by qualied service
personnel. Replacement parts for a double-insulated appliance
must be identical to the parts they replace.
Additional safety rules for blowers
• This tool has been designed for blowing/collecting as
well as vacuuming/shredding dry leaves and other dry
garden rubbish such as grass and twigs.
• This tool is intended for domestic use only and is not
designed to be used under wet conditions.
• This tool is not intended for professional use.
• Read this instruction manual carefully before use and
save it for future reference.
• Pay special attention to the safety instructions and
warnings; failure to follow these may result in serious
injury.
• Check whether the packaging contains all parts as
illustrated in drawing in (Fig. 1), on page 4.
• When parts are missing or damaged, please contact
your dealer.
2
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and
follow all instructions on the machine before attempting to assemble and operate.
Symbols Descriptions
Safety Alert. Caution.
Warning! - To reduce the risk of injury, user
must read instruction manual.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Do not expose to rain. Keep dry.
Caution of flying debris.
Keep the bystander away. Use at a distance of
at least 10 m from other people.
Rotating blades. Keep hands and feet away from
the openings, while the machine is running.
WARNING! Always turn the machine OFF and
disconnect the electrical power before conducting
inspection, cleaning and maintenance. Remove plug
from outlet immediately if the cord is damaged or cut.
Double Insulation
3
Know Your Electric Blower
Due to modern mass production techniques and product testing, it is unlikely that your power tool is
faulty or that a part is missing. If you nd anything wrong, do not operate the tool until the parts have
been replaced or the fault has been rectied. Failure to do so could result in serious personal injury.
7
6
5
4
2
1
8
9
10
11
3
1. Lower/suction tube
2. Upper/suction tube
3. Supporting wheel
4. Front handle
5. Main switch
6. Supporting shoulder
harness
Technical Data
Rated Voltage 120V ~ 60Hz
Rated Power 12 AMPs
Wind Speed 200 MPH
Vaccum Capacity 450 CFM
Fig. 1
7. Main handle
8. Speed adjustable switch
9. Power cord
10. Transfer lever
(Blower or vacuum selctor switch)
11. Collection bag
Mulch Ability 10:1
Bag Cubage 14 GAL
Weight 12.1 lbs
4
Using the blower/vacuum/
Powering ON and OFF (Fig. 5)
leaf shredder
Note: Before using the blower/vacuum/leaf shredder, familiarise
yourself with all the operating features and safety requirements.
Only use the blower/vacuum/leaf shredder as intended.
Assembling (Fig. 2-4)
1. Ensure that the lower/suction tube and the upper/
suction tube is assembled correctly before operating
the tool. NOTE: Check the tubes are secure before
operating the blower.
Fig. 2
Fig. 3
m WARNING! Before switching on the tool, ensure that it
is not in contact with any object.
1. To power on, push the instant start button.
Fig. 5
2. Stop the tool by pushing the Main switch button in "O"
position. Low speed to high speed is from "1" to "6" by
the adjustable switch.
Main Switch Button
Speed Adjustable Switch
m WARNING! After switching off the tool the motor
continues to run for a few seconds.
Vacuuming/Shredding (Fig. 6)
Ensure the tubes are assembled correctly before operating the
unit. Make sure the collection bag is connected to the machine.
Turn the transfer lever switch to VACUUM MODE. Turn unit on.
2. Connect the collection bag to the machine.
Fig. 4
VACUUM MODE
Fig. 6
5
Blowing (Fig. 7)
Ensure the tubes are assembled correctly before operating.
Turn the transfer lever switch to BLOWING MODE. Turn unit on.
• Regularly empty collection bag (the vacuum capacity
decreases considerably when the collection bag is full).
Holding and guiding the tool
m WARNING! While working, always hold the tool at the
light green-colored grip area(s).
• Use supporting wheels for easy guiding the tube along
the ground.
• For optimal distance keep a 5-10 cm to the ground.
BLOWING MODE
Fig. 7
Cord restraint (Fig. 8)
Fig. 8
• Hook the loop in the extension cord over restraint as
illustrated.
• Pull tight to secure the extension cord.
m WARNING! Do not vacuum solid objects such as
stones, broken glass, pieces of metal.
• Do not vacuum liquids.
• Do not vacuum large volumes of leaf material at one time
thus avoiding clogging of the vacuuming opening and
blocking of the shredder impeller.
• The shredding intensity depends on the size of the leaf
material and its residual moisture.
m WARNING! When the tool suddenly stops, immediately
switch it off, disconnect plug from power source, and remove
any jammed material between shredder impeller and housing.
Emptying of collection bag (Fig. 9)
Fig. 9
m WARNING! Switch off the tool and disconnect the plug.
• Wait until the impeller comes to a standstill before
removing the collection bag from the tool.
• Open the zipper of the collection bag and empty it
completely.
• Composte material does not belong with domestic waste.
Maintenance/Service
1. This tool is not intended for professional use.
2. Always keep tool and cord clean.
• Clean the tool after each use with a soft brush or a cloth
(do not use cleaning agents or solvents).
• Remove the collection bag after each use, turn inside out
and clean it thoroughly.
• After removing the collection bag, ensure that possible
dirt residues are removed from the air outlet area.
3. Store the tool indoors in a dry place.
• Do not cover the tool with plastic.
• Plastic may cause moisture and corrosion will result.
4. If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for
power tools.
• Send the tool undismantled together with proof of
purchase to your dealer.
6
Troubleshooting
m
WARNING! Always unplug the power cord before performing any adjustments, maintenance, or repairs to your
blower/vacuum.
Problem
The blower/
vacuum/leaf
shredder fails to
operate
The blower/
vacuum/leaf
shredder operates
intermittently
No/low blowing
power
No/low vacuuming
power
Cause
• No power supply
• Plug not connected
• Extension cord damaged
• On/off switch defective
• Worn carbon brushes
• Defective motor
• Blowing/vacuum tube not completely mounted
• On/off switch defective
• Internal wiring defective
• Impeller blocked by foreign object
• Selector switch in vacuuming mode
• Selector switch in blowing mode
• Collection bag is full.dirty
• Vacuuming opening clogged up or blocked by
foreign object
Remedy
• Check power supply (power cable, circuit breakers, fuses).
• Connect the plug
• Replace extension cord
• Contact dealer/service station
• Mount two-part blowing/vacuum tube
• Contact dealer/service station
• Remove blockage
• Set selector switch in blowing mode
• Set selector switch in vacuuming mode
• Empty/clean collection bag
• Remove blockage
Environment
1. Do not dispose of electric tool, accessories and
packaging together with household waste material.
2. The vibration emission level has been measured in
accordance with a standardized test given in EN/
ISO 3744; it may be used to compare one tool with
another and as a preliminary assessment of exposure
to vibration when using the tool for the applications
mentioned.
• Using the tool for different applications, or poorly
maintained accessories, may signicantly increase the
exposure level.
• The times when the tool is switched off or when it is
running but not actually doing the job, may signicantly
reduce the exposure level.
mWARNING! Protect yourself against the effects of
vibration by maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns.
Service and Support
If your Snow Joe blower/vacuum requires service or
maintenance, please call 1-866-766-9563 for assistance.
Model and Serial Numbers
When contacting the company or reordering parts, you
will need to provide the model and serial numbers of your
products. These are found on the decal afxed to the housing
or at the bottom of your blower/vacuum/leaf shredder. Copy
these numbers into the space provided below.
Record the following numbers from the housing or handle of your
new product:
Model #:
S B J 6 0 4 E R M
Serial #:
7
A One-Year Full Warranty
for residential use
in the United States and Canada
General Conditions:
Snow Joe®, LLC warrants this product to the original purchaser for one year against defects in material or workmanship when used
for normal residential purposes. Snow Joe
part, subject to the conditions, limitations, and exclusions set forth herein. Such repair or parts replacement will be free from charge to
the original purchaser except noted below.
The duration of the warranty applies only if the product is put to personal use around the household or residence. If the product is put
to any business use, commercial or industrial, then the duration of this warranty is 90 days from the date of original purchase. If any
product is rented or leased, the duration of the warranty is 90 days from the date of original purchase.
It is the owner’s responsibility to perform correctly all maintenance, and minor adjustments explained in the owner’s manual.
Electric Products:
To obtain a replacement electric powered unit or repair the existing electric powered unit, you must return the complete unit and
postage prepaid to: Snow Joe Return Center, 86 Executive Avenue, Edison, NJ 08817.
Gasoline / Battery Products:
Limitations
• Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis. Rechargeable batteries
will be replaced free from charge during the rst 90 days. After the initial 90 days, batteries will be replaced at a prorated cost to
the customer.
• Idlers, cables, and electrical components are warranted to the original purchaser for use at household or residence for a period
of one year.
®
, LLC will repair any defect in material or workmanship, and repair or replace any defective
Exclusions
®
• Snow Joe
brand engines are covered under this warranty. All other engines and engine accessories are covered only by the
engine manufacturer’s warranty and are not covered by this warranty.
®
• Parts used that are not genuine Snow Joe
parts are not covered by this warranty.
• Damages resulting from misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires repair
is not covered under this warranty.
• Belts, augers, and tines are not covered under warranty – belts, augers, and tines wear out and can be purchased at
www.snowjoe.com or by calling 1-866-766-9563.
®
Snow Joe
obligating Snow Joe
, LLC may from time to time change the design of its products. Nothing contained in this warranty shall be construed as
®
, LLC to incorporate such design changes into previously manufactured products, nor shall such changes be
construed as an admission that previous designs were defective.
®
This warranty is intended to cover product defects only. Snow Joe
®
in connection with the use of the Snow Joe
Products covered by this warranty. This warranty does not cover any cost or expense
, LLC is not liable for indirect, incidental, or consequential damages
incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this
product, while waiting for completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential
damages, so the above exclusions may not apply in all states. This warranty may give you specic legal rights in your state.
®
If you wish to contact Snow Joe
, please direct inquiries to the:
Customer Service Department
Snow Joe Center
86 Executive Avenue
Edison, NJ 08817
®
Customers who have purchased Snow Joe
products exported from the United States and Canada should contact their Snow Joe®
Distributor (Dealer) to obtain information applicable for your country, province, or state. If for any reason, you are not satised with the
®
distributor’s service, or if you have difculty obtaining warranty information, contact your Snow Joe
®
are unsatisfactory, please write to the Snow Joe
Center at the above address.
seller. If in the event your efforts
If you have any questions about your product warranty, please call 1-866-SNOW-JOE or visit us online at www.snowjoe.com.
8
Loading...