SnowEx RHT-380 User Manual
Installation Guide
This Manual Must Be Read Before Operating The Equipment
Madison Heights, Michigan 48071
800-725-8377
www.snowexproducts.com
(REV B) F50767
RHT-380
CUSTOMER COPY
1© Trynex International 2013
Introduction
Model # RHT-380
This Installation Guide is designed to assist you when mounting your Snowex Spreader on your truck using the RHT-375 Mount. This guide is not
a replacement for your Spreader Owner’s Manual. Read and understand all safety information contained in the Spreader Owner’s Manual before
installing and using the RHT-375. Use caution at all times and take all necessary precautions to avoid injury to yourself and others.
Remember it is better to have extra assistance and precautions in
order to avoid injury.
Do not lift spreader by yourself, seek competent assistance before
attempting to lift spreader onto vehicle.
Use all necessary precautions, such as ratchet straps, clamps or
other support/holding devices, to prevent spreader from falling or
tipping.
Keep hands clear of all pinch points. Areas likely to be pinch points
are those where two separate parts butt against each other.
Park vehicle on level ground before installing the spreader.
Follow all vehicle safety information.
Install straps before putting material in hopper.
Have a question or need assistance?
SnowEx Customer Care
1-800-SALTERS
or (248) 586-3500
Monday through Friday 8:00 AM to 4:30 PM EST
Fax: (248) 691-8378
E-Mail: customercare@trynexfactory.com
Website: www.snowexproducts.com
© Trynex International 2013 (REV B) F507672
Parts Breakdown
14
8
2
9
1
12
15
7
4
6
6
7
3
13
16
7
6
11
7
5
10
ID #
Part #
Description
Qty
1
D4116
Bolt 1/2"-13 X 1-1/2" Hex Head Zinc
4
2
D4119
1/2" FLAT USS WASHER ZINC
4
3
D4120
Nut 1/2"-13 Nylox Zinc
2
4
D4121
Bolt | 3/8"-16 X 1" Hex Head Zinc
12
5
D4122
Bolt | 3/8"-16 X 1-1/2" Hex Head Zinc
8
6
D4124
Nut | 3/8"-16 Nylok Zinc
28
7
D4125
Washer | 3/8" Flat USS Zinc
36
8
D4135
Hair Pin Cotter .093 X 2-3/8" Zinc
1
9
D4136
Hitch Pin 5/8" X 5-1/2"
1
10
D6388
Upright Support Bracket
2
11
D6392
3/8"-16 X 3" FULL THREAD HEX HEAD ZINC
8
12
F50687
Ratchet Strap | 1” x 12’
2
13
D6791
Adjustable Foot RHT 375
2
14
F50773
RHT-380 Receiver Mount
1
15
F50800
RHT-380 Mounting Arm
4
16
F50801
Vertical Bracket | RHT-380
4
Model # RHT-380
3© Trynex International 2013 (REV B) F50767
Installation Instructions
Model # RHT-380
Step 1: Insert Mounting Arms (F50800) into spreader frame.
All diagrams are shown with SP-1075 conguration.
Step 2: Assemble Mounting Arms to Vertical Brackets (F50801) then to
Upright Support Brackets (D6388) using supplied hardware .
© Trynex International 2013 (REV B) F507674
Loading...