Parts Manual fo
r
E
V
V
TURF / TRAIL CRUISER
UTILITY VEHICL
SERIES 1
MODEL
UV1621BV
UVG1621B
UVGT1621B
Briggs & Startton Yard Power Products Group
Copyright © 2007
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
Revision 2,
McDonough, GA, 30253 U.S.A.
7/23/2007
Manual No. 7006179
TP 400-5042-2-GC-N
s
PAGE GROUP
4
6
8
10
12
16
18
20
22
26
30
32
34
36
40
42
46
48
50
52
54
56
58
60
62
64
66
70
72
74
76
78
BUMPER GROUP (Early Production)
BUMPER GROUP (Late Production)
HOOD GROUP
FRONT CLIP GROUP (Dash)
FRONT CLIP GROUP (Pedals)
STEERING GROUP
FRONT SUSPENSION GROUP
SEAT GROUP
SEAT PEDESTAL GROUP- Frame
SEAT PEDESTAL GROUP- Controls
FRONT FRAME GROUP- Sub-Assembly
FRONT FRAME GROUP- Final Assembly
REAR FRAME GROUP, LH
REAR FRAME GROUP, RH
BRAKE ASSEMBLY
DRIVE BASE GROUP
CVT AXLE GROUP
BED ASSEMBLY (Dump Bed)
BED ASSEMBLY (Tail Gate)
BED ASSEMBLY (Latch)
WHEEL GROUP (TURF & TRAIL TIRE)
ROPS/ACCESSORY GROUP
BRUSH GUARD GROUP
WINCH GROUP
DECAL GROUP (Snapper)
DECAL GROUP (Continued)
ELECTRICAL GROUP
WIRING HARNESS- UV & UVG Models
WIRING HARNESS- UVGT (UVGC) Model
WIRING SCHEMATIC- UV Model
WIRING SCHEMATIC- UVG Model
WIRING SCHEMATIC- UVGT (UVGC) Model
Table Of Content
SERIES 1
Manual No. 7006179TURF / TRAIL CRUISER
3
TP 400-5042-2-GC-N
BUMPER GROUP (Early Production)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
4
SERIES 1
BUMPER GROUP (Early Production)
p
y
Part No Descri
1 7028009 1 BUMPER SUPPORT, LH
2 7028022 1 SUPPORT, Bumper
3 7028029 1 PLATE, Winch
4 7028072 1 BUMPER
5 7091299 4 NUT, 3/8-16 Hex Nyloc or 7076979
6 7090659 4 BOLT, 3/8-16 x 1-1/4” Hex Flange Lock
7 7091298 4 NUT, 5/16-18 Hex Nyloc
8 7091681 4 BOLT, 5/16-18 x 1” Hex Flange Lock
9 7091619 4 NUT, 3/8-16 Hex Flange Lock
tionItem Qt
Note
Footnotes:
SERIES 1
Manual No. 7006179TURF / TRAIL CRUISER
5
TP 400-5042-2-GC-N
BUMPER GROUP (Late Production)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
6
SERIES 1
BUMPER GROUP (Late Production)
p
y
Part No Descri
1 7078209 1 BUMPER SUPPORT, Left
2 7078208 1 BUMPER SUPPORT, Right
3 7078201 1 PLATE, Winch Mounting
4 7078210 1 BUMPER late production UV1621BV &
5 7091299 4 NUT, 3/8-16 Hex Nyloc
6 7027198 4 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5
7 7091619 4 NUT, 3/8-16 Hex Flange Lock
8 7027168 4 SCREW, 5/16-18 x 1” Hex Head Cap, GR 5
9 7090188 2 WASHER, .34 x .69 x .08 Flat
10 7091298 4 NUT, 5/16-18 Hex Nyloc
tionItem Qt
Note
UVG1621BV & all UVGT(or
UVGC)621BV
Footnotes:
SERIES 1
Manual No. 7006179TURF / TRAIL CRUISER
7
TP 400-5042-2-GC-N
HOOD GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
8
SERIES 1
HOOD GROUP
p
y
Part No Descri
1 7043253 1 WELDMENT, Hood (Red)
1 7043254 1 WELDMENT, Hood (Green)
2 7035270 5 HOOD PAD
3 7043211 1 PLATE WASHER
4 7091833 4 SCREW 5/16-18 x 5/8” Cross Recessed Pan Head
5 7043208 1 HOOD PROP
6 7043209 1 BRACKET, Hood Prop
7 7090188 1 WASHER, .34 x .69 x .08 Flat
8 7091597 1 COTTER PIN, 3/32 x 3/4”
9 7043210 1 HOLDER, Hood Prop
10 7092074 1 SCREW, #6-20 x .34 Pan Head Self-Tap
11 7091942 2 SCREW, #10-24 x 1/2” Pan Head Machine
12 7091317 6 SCREW, 1/4-20 x 3” Hex Head Cap, GR 5 Ref. FRONT CLIP GROUP
13 7091216 4 SCREW, #10 x 1-1/4” Hex Washer Self-Tap, HI-LO
14 7029051 2 ASSY, Hood Latch (incl. Ref, Nos. 15 & 16)
15 7028017 1 KEEPER
16 7028035 1 ASSEMBLY, Hood Handle consists of 7028035 (Handle) &
tionItem Qt
Note
(Dash) page, item 5
7043029 (Bracket)
Footnotes:
SERIES 1
Manual No. 7006179TURF / TRAIL CRUISER
9
TP 400-5042-2-GC-N
FRONT CLIP GROUP (Dash)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
10
SERIES 1
FRONT CLIP GROUP (Dash)
p
y
Part No Descri
1 7075818 1 FENDER, UV-2
2 7078813 1 DASH, UV-2
3 7091602 8 BOLT, 5/16-18 x 1-1/2” Hex Flange Lock, GR 5
4 7091253 6 WASHER, .281 x .750 x .051 Flat
5 7091317 6 SCREW, 1/4-20 x 3” Hex Head Cap, GR 5
6 7063343 1 WELDMENT, Steering Support
7 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR 5
8 7073163 1 PIVOT BRACKET, Throttle
9 7091776 2 BOLT, 1/4-20 x 3/4” Square Neck Carriage
10 7091584 6 NUT, 1/4-20 Hex Flange Lock, GR 5
11 7041967 1 WELDMENT, Column Support
12 7035496 2 BEARING, .750 I.D. Ref. SEAT PEDESTAL GROUP-
13 7091148 4 SCREW, 1/4-20 x 1/2” Pan Head Machine
tionItem Qt
Note
Controls, item 25
Footnotes:
SERIES 1
11
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
FRONT CLIP GROUP (Pedals)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
12
SERIES 1
FRONT CLIP GROUP (Pedals)
p
y
Part No Descri
1 7058125 1 WELDMENT, CVT Brake Pedal
2 7073876 1 SWIVEL, Brake Rod
3 7091528 1 WASHER, .375 x .875 x .083 Flat
4 7091598 2 COTTER PIN, 1/8 x 3/4”
5 7012306 1 FLANGE BUSHING, .381 x .625 x .62
6 7058753 1 WELDMENT, Brake Switch Rod
7 7014432 1 SPRING
8 7090122 1 WASHER, 3/8” SAE Flat
9 7090543 2 SCREW, 1/2-13 x 2” Hex Head Cap, GR 5
10 7091922 2 NUT, 1/2-13 Hex Nyloc or 7091121
11 7058556 1 ASSEMBLY, Upper Brake Rod composed of 7072988, 7073012
12 7073012 2 ROD END, Female 1/2-20 thread part of item 12 assembly
13 7072988 1 ROD, Upper CVT Brake (1/2-20 thread) part of item 12 assembly
14 7090559 2 NUT, 1/2-20 Hex Jam, GR 5 or B part of item 12 assembly
15 7058748 1 WELDMENT, Throttle Pedal
16 7072502 2 PEDAL GRIP
17 7072600 1 SPRING, Throttle Pedal Return
18 7072602 1 SPRING, Inner Throttle Return
19 7012709 2 RING, 1.00 Dia. External Retaining
20 7016561 2 BUSHING, 14 Gage Machine
21 7072645 2 BEARING, 1” I.D.
22 7050520 2 BRACKET, Brake Support (Red) 7072518 is the un-painted part
22 7035752 2 BRACKET, Brake Support (Green) Trailmaster version of 7072518
23 7050522 1 FIREWALL, LH (Red) 7075870 is the un-painted part
23 7035754 1 FIREWALL, LH (Green) Trailmaster version of 7075870
24 7050523 1 FIREWALL, RH (Red) 7075871 is the un-painted part
24 7035755 1 FIREWALL, RH (Green) Trailmaster version of 7075871
25 7078098 1 FILLER, Firewall LH (Red)
25 7078103 1 FILLER, Firewall LH (Green)
26 7078099 1 FILLER, Firewall RH (Red)
26 7078104 1 FILLER, Firewall RH (Green)
27 7078031 2 GASKET, Closed Cell, Adhesive Back
28 7050521 1 PEDAL SHIELD (Red) 7072588 is the un-painted part
28 7035753 1 PEDAL SHIELD (Green) Trailmaster version of 7072588
29 7091508 8 BOLT, 5/16-18 x 3/4” Short Square Neck Carriage, GR 5
30 7091601 8 NUT, 5/16-18 Hex Flange Lock, GR 5
31 7091579 13 SCREW, 1/4-20 x 1/2” Hex Flange Lock, GR 5
tionItem Qt
Note
(2) and 7090559 (2)
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 699 & UV Serial #'s 50029300 thru 399.
SERIES 1
13
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
FRONT CLIP GROUP (Pedals)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
14
SERIES 1
FRONT CLIP GROUP (Pedals)
p
y
Part No Descri
32 7091584 9 NUT, 1/4-20 Hex Flange Lock, GR 5
33 7091819 2 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap
34 7092133 14 SCREW, #10-16 x 1-1/4” Truss Head Sheet Metal was 7092106
35 7034741 1 * KICK PLATE, LH
36 7034648 1 * KICK PLATE, RH
tionItem Qt
Note
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 699 & UV Serial #'s 50029300 thru 399.
SERIES 1
15
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
STEERING GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
16
SERIES 1
STEERING GROUP
p
y
Part No Descri
1 1725024 1 CENTER CAP, Steering Wheel
2 7092036 1 NUT, M16 x 2 thread Hex, GR 5 in hardware bag
3 7092042 1 WASHER, 16mm Split Lock in hardware bag
4 1722318 1 * STEERING WHEEL (w/cross drilled hole)
4 7078088 1 STEERING WHEEL, UV-2 (w/40 tooth splined hole)
5 1678381 1 COVER, Steering Shaft
6 7072638 1 COVER, Steering Shaft 4” long
7 7090845 1 * ROLL PIN, 5/16 x 1-1/2”
8 7027496 1 * COLUMN, Steering (w/cross drilled hole)
8 7078191 1 COLUMN, Steering (w/40 tooth spline)
9 7091187 1 NUT, 10mm-1.50 Hex Nyloc
10 7091184 1 SCREW, M10-1.50 x 40mm Hex Head Cap
11 7028075 1 ASSEMBLY, Rack and Pinion Steering
12 7090559 2 NUT, 1/2-20 Hex Jam, GR 5 or B
13 7036465 2 BALL JOINT, 1/2-20
14 7072637 4 SPACER, 1/2 I.D., 5/8 O.D. x .375
15 7091121 2 NUT, 1/2-13 Hex Nyloc or 7091922
16 7090544 2 SCREW, 1/2-13 x 2-3/4 Hex Head Cap, GR 5
17 7092079 6 INSERT, 5/16-18 Hex Threaded
18 7091905 2 BOLT, 5/16-18 x 7/8” Hex Flange Lock
19 7090188 6 WASHER, .34 x .69 x .08 Flat
20 7091315 6 WASHER, .32 x .58 x .08 Split Lock
21 7091058 4 SCREW, 5/16-18 x 3-3/4” Hex Head Cap
tionItem Qt
Note
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 699 & UV Serial #'s 50029300 thru 399.
SERIES 1
17
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
FRONT SUSPENSION GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
18
SERIES 1
FRONT SUSPENSION GROUP
p
y
Part No Descri
1 7029258 8 BUSHING, Suspension
2 7072614 2 ASSEMBLY, Shock/Spring
3 7029263 4 SLEEVE, Suspension
4 7029355 4 BOLT, 1/2-13 x 3-3/4” Hex Head, GR 5
5 7091703 4 SCREW, 7/16-20 x 2-1/2” Hex Head Cap (Special) GR 5 or 7092071: SCREW, 7/16-20 x
6 7090970 4 NUT, 7/16-20 Hex Top Lock
7 7019572 4 BALL BEARING, 6205-2RS
8 7092038 2 NUT, 3/4-16 Slotted Hex, GR 5
9 7090297 2 COTTER PIN, 1/8 x 1-1/2”
10 7072615 2 WHEEL HUB, Front plate with 5 pressed-in 1/2-20
11 7072618 2 SPACER, Front Wheel
12 7091922 4 NUT, 1/2-13 Hex Nyloc or 7091121
13 7058539 1 ASSY, RH A-Arm & Spindle (incl. Ref. Nos. 14 thru 20)
14 7013864 2 LUBE FITTING, 3/16” Serrated
15 7023556 4 BUSHING, Caster
16 7058432 1 A-ARM WELDMENT, RH
17 7058485 1 SPINDLE WELDMENT, RH
18 7072679 2 ROD, Spindle Pivot
19 7090505 2 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
20 7091603 2 NUT, 1/4-20 Hex Nyloc
21 7058596 1 ASSY, LH A-Arm & Spindle (incl. Ref. Nos. 14, 15, 18, 19, 20, 22
& 23)
22 7058419 1 SPINDLE, WELDMENT, LH
23 7058484 1 A-ARM WELDMENT, LH
24 7016561 2 BUSHING, 14 Gage Machine
25 7031965 2 THRUST WASHER, 3/4” I.D.
26 7027192 10 LUG NUT, 1/2-20 Hex
tionItem Qt
Note
2-1/2” Hex Head Cap, GR 5
w/locking patch
threaded studs
(not shown)
Footnotes:
SERIES 1
19
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
SEAT GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
20
SERIES 1
SEAT GROUP
p
y
Part No Descri
1 7017875 4 KNOB, 3 Prong, 5/16-18 x 2” Stud
2 7033318 2 SUPPORT, Seat, Upper
3 7091525 6 BOLT, 5/16-18 x 1/2” Hex Flange Lock, GR 5
4 7019109 4 COVER, Spring (Rubber)
5 7090188 4 WASHER, .34 x .69 x .08 Flat
6 7035271 2 SEAT, Milsco XB-150, 15” No Logo
6 7100162 2 SEAT, Milsco XB-180 (19.5” High Back)
7 7063295 2 ASSEMBLY, Seat Support, (incl. Ref. Nos. 8 thru 11)
8 7015707 1 SWITCH, Seat (NO)
9 7028580 1 HOLDER, Seat Cushion E.C.
10 7073266 2 SPRING, Cushion Holder
11 7074204 1 SUPPORT, Seat E.C. per 7063295 assembly;
12 7074452 2 ROD, Seat Hinge in hardware bag
13 7091503 2 HAIR PIN, 3/32 x 1-1/2” in hardware bag
14 7073532 2 SEAT BELT, 60” (incl. Ref. Nos. 16 thru 18) in hardware bag
15 7090991 4 WASHER, 7/16” Flat (Type A, Wide)
16 -- 4 * SCREW, 7/16-20 x 2” Hex Head Cap, GR 5
17 -- 4 * WASHER, 1/2” I.D. x 2-1/2” O.D. Flat
18 -- 4 * NUT, 7/16-20 Hex Nyloc
tionItem Qt
Note
7074204 replaces 7028579
Footnotes:
Note: * Fasteners are supplied by Femco with seat belt.
SERIES 1
21
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
SEAT PEDESTAL GROUP- Frame
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
22
SERIES 1
SEAT PEDESTAL GROUP- Frame
p
y
Part No Descri
1 7027247 1 PEDESTAL, Seat, Red 7075869 is the un-painted part
1 7063290 1 PEDESTAL, Seat, Green used on UVGT (or UVGC)
2 7046974 1 GAS TANK, UV includes Gas Cap, item 3
3 7075135 1 GAS CAP
4 7046975 1 SENDING UNIT, UV gas tank
5 7091942 5 SCREW, #10-24 x 1/2” Pan Head Machine
6 7043263 1 ENDCAP, Red
6 7043264 1 ENDCAP, Green or 7061329; used on UVGT (or
7 7091579 10 SCREW, 1/4-20 x 1/2” Hex Flange Lock, GR 5
8 7091584 6 NUT, 1/4-20 Hex Flange Lock, GR 5
9 7092048 18 SCREW, 5/16-18 x 1” Cross Recessed Round Hd Mach. GR 5 or 7091811 (5/16-18 x 5/8” Hex
10 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR 5
11 7092079 4 INSERT, 5/16-18 Hex Threaded
12 7072586 2 HANDLE, Seat Pedestal
13 7091592 8 BOLT, 5/16-18 x 2” Hex Flange Lock, GR 5
14 7091528 8 WASHER, .375 x .875 x .083 Flat
15 7091298 8 NUT, 5/16-18 Hex Nyloc
16 7034101 1 GAS TANK STRAP
16 7063158 1 GAS TANK STRAP (Trailmaster version) not used in production
17 7091240 4 SCREW, #10-32 x 5/8 Hex Washer Head Machine
18 7090376 6 NUT, #10-32 Hex Nyloc
19 7043251 1 WELDMENT, Power Generator End Cap, LH (Red) used on UVG1621BV UV2
19 7074319 1 * WELDMENT, Power Generator End Cap, LH (Green) used on UVGT (or UVGC)
20 7027498 1 THROTTLE, Remote, Powerlink used on UVG & UVGT (or
21 7024538 1 BRACKET, Seat Pedestal Support black textured finish
21 7063288 1 BRACKET, Seat Pedestal Support (Green) no longer used; order 7024538
22 7035496 1 BEARING, 3/4” I.D.
23 7077345 8 PAD - Gas Tank
24 7022229 1 WELDMENT, Hi-Lo Cam Pivot
25 7090799 3 BOLT, 5/16-18 x 5/8” Short Square Neck Carriage, GR 5
26 7011791 3 RETAINER, 5/16” Bolt
27 7026405 1 FOOTPAD, Center, UV-2
28 7026290 1 FOOTPAD, LH, UV-2
29 7026190 1 FOOTPAD, RH UV-2
30 7027256 1 FLOORPAN, Red 7075874 is the un-painted part
30 7063300 1 FLOORPAN, Green used on UVGT (or UVGC)
31 7017853 1 TRAY, Battery
tionItem Qt
Note
UVGC)
Flange Lock Bolt)
w/Powerlink
UVGC); also shown on DRIVE
BASE GROUP
Footnotes:
Note: * Part # 7074319 has a hole for the Winch Remote Plug , unlike 7029164, raw part.
SERIES 1
23
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
SEAT PEDESTAL GROUP- Frame
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
24
SERIES 1
SEAT PEDESTAL GROUP- Frame
p
y
Part No Descri
32 7034358 1 BRACKET, Battery Hold Down
33 7090721 5 BOLT, 5/16-18 x 1/2” Hex Flange Lock
34 7072629 1 RETAINER, Battery (Rod) not used in production
tionItem Qt
Note
Footnotes:
Note: * Part # 7074319 has a hole for the Winch Remote Plug , unlike 7029164, raw part.
SERIES 1
25
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
SEAT PEDESTAL GROUP- Controls
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
26
SERIES 1
SEAT PEDESTAL GROUP- Controls
p
y
Part No Descri
1 7072718 1 CONSOLE, UV-2
2 1725277 1 KNOB, Park Brake, Red used on all models
2 1715946 1 KNOB, Parking not used in production
3 1709188 1 PLUG, Dash Hole
4 7011259 1 SWITCH, Momentary Rocker (On-Off-On) for Electric Bed Lift (if so
5 7073090 1 OUTLET, 12 Volt DC Power
6 7027908 1 CABLE, Choke, B&S 16HP Vanguard used on UVGT(or UVGC)621BV
7 7090390 5 WASHER, 3/8” Internal Tooth Lock
8 7090155 1 NUT, 3/8-24 Hex, GR B
9 7090721 4 BOLT, 5/16-18 x 1/2” Hex Flange Lock
10 7091240 2 SCREW, #10-32 x 5/8” Hex Washer Head Machine
11 7046805 1 CONTACT PLATE, Differential Lock
12 7090376 3 NUT, #10-32 Hex Nyloc 1 is used with knob 1725337.
13 1722303 1 HANDLE, Shift
14 7027230 1 SCREW, 1/4-20 x 1” Hex Head Cap, GR 5
15 7091584 5 NUT, 1/4-20 Hex Flange Lock, GR 5
16 7041808 1 WELDMENT, Shift Rod
17 7043859 1 SPRING, Transmission Extension (Short)
18 7011021 1 CLEVIS PIN, 1/4 x 1-1/4”
19 7091597 1 COTTER PIN, 3/32 x 3/4”
20 7010745 2 BALL JOINT, 3/8-24 Thread
21 7091630 5 NUT, 3/8-24 Hex, GR B
22 7034583 1 ROD, CVT Shift, 21-5/8” Long (3/8-24 thread- both ends)
23 7034610 1 HEX BLOCK, Shift Adj. (3/8-24 thread, LH & RH)
24 7034584 1 ROD, CVT Shift, 12-1/8” Long (3/8-24 thread, LH & RH)
25 7035496 2 BEARING, .750 I.D.
26 7012068 1 RING, Rear Lift Arm- Blue
27 7043233 1 WELDMENT, Trans. Shifter (9.44” inside measure) was 7041011 (10.94” inside
28 7023655 1 LEVER, Throttle Control used in all late production UV,
29 7071921 1 RIVET, Plastic Snap used in all late production UV,
30 7091579 4 SCREW, 1/4-20 x 1/2” Hex Flange Lock, GR 5
31 7047084 1 ASS'Y, Differential Lock (incl. items 11, 15, 30, 35 & 42) used on all models
31 7063166 1 ASSEMBLY, Differential Lock (Camo version) not used in production
32 7072939 1 CABLE, Differential Lock
33 960604 1 * SCREW, Hex Washer Head Slot #10 x 1”
34 1725337 1 * KNOB, Throttle (Red)
35 7041788 1 ASSEMBLY, Differential Lock (Includes next 6 items)
tionItem Qt
Note
equipped)
measure)
UVG and all UGVT (or UVGC).
UVG and all UGVT (or UVGC).
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 50028699 and UV Serial #'s 50029300 thru 50029399.
SERIES 1
27
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
SEAT PEDESTAL GROUP- Controls
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
28
SERIES 1
SEAT PEDESTAL GROUP- Controls
p
y
Part No Descri
36 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
37 7090517 2 WASHER, 3/8” SAE Flat
38 7028036 1 SPRING, Friction Pack
39 7011260 1 LEVER, Differential Lock was 7074677
40 7046803 1 BRACKET, Differential Lock
41 7091299 1 NUT, 3/8-16 Hex Nyloc
42 7046802 1 MOUNTING PLATE, Differential Lock
tionItem Qt
Note
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 50028699 and UV Serial #'s 50029300 thru 50029399.
SERIES 1
29
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
FRONT FRAME GROUP- Sub-Assembly
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
30
SERIES 1
FRONT FRAME GROUP- Sub-Assembly
p
y
Part No Descri
1 7058505 1 WELDMENT, Inner LH Frame Rail NOTE: 7058667, Front Frame
2 7058551 1 WELDMENT, Inner RH Frame Rail
3 7058694 2 WELDMENT, Outer CVT Frame
4 7058739 1 WELDMENT, Steering Bracket
5 7072464 1 END, Frame
6 7072473 1 SUSPENSION PIVOT, RH
7 7072516 1 STIFFENER, Frame
8 7072619 1 SUSPENSION PIVOT, LH
9 7091601 18 NUT, 5/16-18 Hex Flange Lock, GR 5
10 7091714 18 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5
11 7091811 18 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
12 7027198 6 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5
13 7027181 4 BOLT, 3/8-16 x 1-1/4” Short Square Neck Carriage, GR 5
14 7013847 4 RETAINER, 3/8” Bolt
15 7091588 2 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR 5
tionItem Qt
Note
Pre-Paint Sub-assy. Is made up
of parts 1 thru 12.
Footnotes:
SERIES 1
31
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
FRONT FRAME GROUP- Final Assembly
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
32
SERIES 1
FRONT FRAME GROUP- Final Assembly
p
y
Part No Descri
1 7012709 2 RING, 1.00 Dia. External Retaining
2 7091714 4 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5
3 7016561 2 BUSHING, 14 Ga Machine
4 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR 5
5 7044680 1 WELDMENT, Grill Support
6 7058648 1 WELDMENT, Lower CVT Brake
7 7072645 2 BEARING, 1” I.D.
8 7072989 1 ROD, Lower CVT Brake (1/2-20 thread, both ends)
9 7073012 1 ROD END, Female 1/2-20
10 7073091 1 SUSPENSION GUSSET, LH
11 7073092 1 SUSPENSION GUSSET, RH
12 7073162 1 THROTTLE ANCHOR, Front (black) used on UV, UVG & UVGC
12 7074326 1 THROTTLE ANCHOR, Front not shown; Trailmaster version
13 7079295 1 NUT, 1/2-20 Hex Nyloc
14 7090543 1 SCREW, 1/2-13 x 2” Hex Head Cap, GR 5
15 7090559 2 NUT, 1/2-20 Hex Jam, GR 5 or B
16 7091922 1 NUT, 1/2-13 Hex Nyloc or 7091121
17 7091541 8 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
18 7091588 16 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR 5
19 7091619 20 NUT, 3/8-16 Hex Flange Lock
20 7041033 6 NUT, 1/4” Tinnerman
21 7027198 4 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5
tionItem Qt
Note
models
of 7073162; used on
UVGT621BV
Footnotes:
SERIES 1
33
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
REAR FRAME GROUP, LH
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
34
SERIES 1
REAR FRAME GROUP, LH
p
y
Part No Descri
1 7027351 1 FRAME, Rear LH (Red) 7072943 is the un-painted part
1 7069499 1 FRAME, Rear, LH (Green) Trailmaster version of 7072943
2 7058635 1 WELDMENT, Tube Brace (Flat Black) used on all models
2 7063350 1 WELDMENT, Tube Brace (Green) not used in production
3 7027352 1 CHANNEL, Frame Stiffener (Red) 7073062 is the un-painted part
3 7074318 1 CHANNEL, Frame Stiffener (Camo) Trailmaster version of 7073062
4 7058738 1 WELDMENT, Bed Prop
5 7015446 1 BOLT, 3/8-24 x .760 Hex Head, Shoulder, GR 5
6 7028354 1 BRACKET, Bed Latch 1 per side
7 7073190 1 PIN, Bed Latch Striker (7/16-14 thread) 1 per side
8 7072962 4 BUMPER, Rubber 2 per side
9 7027328 2 WELDMENT, Dump Bed Pivot (Red) 1 per side; 7058686 is the un-
9 7063351 2 WELDMENT, Dump Bed Pivot (Green) Trailmaster version of 7058686
10 7029258 4 BUSHING, Suspension 2 per side
11 7027324 2 STIFFENER, CVT Frame (Red) 1 per side; 7072945 is the un-
11 7035762 2 STIFFENER, CVT Frame (Green) Trailmaster version of 7072945
12 7091518 1 NUT, 3/8-24 Hex Nyloc
13 7091917 1 NUT, 7/16-14, Hex Nyloc 1 per side
14 7091681 6 BOLT, 5/16-18 x 1” Hex Flange Lock 3 per side
15 7090815 24 SCREW, 3/8-16 x 3/4” Hex Washer Self-Tap 12 per side
16 7091905 46 BOLT, 5/16-18 x 7/8” Hex Flange Lock
17 7091811 55 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 11 per side
18 7091299 21 NUT, 3/8-16 Hex Nyloc 8 on left side
19 7027198 12 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5 2 on left side
20 7091601 61 NUT, 5/16-18 Hex Flange Lock, GR 5 16 on left side
21 7029263 2 SLEEVE, Suspension 1 per side
22 7046206 1 WELDMENT, Drive Base also shown on DRIVE BASE
23 7091922 3 NUT, 1/2-13 Hex Nyloc or 7091121
24 7091821 1 SCREW, 1/2-13 x 3” Hex Head Cap
25 7029355 2 BOLT, 1/2-13 x 3-3/4” Hex Head, GR 5
26 7034880 1 TOOLBOX, Turf/Trail Cruiser (Black)
27 7078187 1 BRACKET, Toolbox, LH (Red) was 7029368
27 7078189 1 BRACKET, Toolbox, LH (Green)
28 7078188 1 BRACKET, Toolbox, RH (Red) was 7029370
28 7078190 1 BRACKET, Toolbox, RH (Green)
29 7043206 1 MAT, Toolbox
tionItem Qt
Note
painted part
painted part
GROUP page
Footnotes:
SERIES 1
35
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
REAR FRAME GROUP, RH
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
36
SERIES 1
REAR FRAME GROUP, RH
p
y
Part No Descri
1 7027331 1 FRAME, Rear RH (Red) 7072571 is the un-painted part
1 7068000 1 FRAME, Rear, RH (Green) Trailmaster version of 7072571
2 7027967 1 BRACKET, Speed Sensor (weldment)
3 7026570 1 SENSOR, Speed ref: Electrical Components Group
4 7034054 1 BRACKET, Air Filter
5 7072563 2 BRACKET, Transmission Shift
6 7028354 1 BRACKET, Bed Latch 1 per side
7 7073190 1 PIN, Bed Latch Striker (7/16-14 thread) 1 per side
8 7072962 4 BUMPER, Rubber 2 per side
9 7027328 2 WELDMENT, Dump Bed Pivot, Red 1 per side; 7058686 is the un-
9 7063351 2 WELDMENT, Dump Bed Pivot (Green) Trailmaster version of 7058686
10 7029258 4 BUSHING, Suspension 2 per side
11 7027324 2 STIFFENER, CVT Frame (Red) 1 per side; 7072945 is the un-
11 7035762 2 STIFFENER, CVT Frame (Green) Trailmaster version of 7072945
12 7058636 1 WELDMENT, Shifter Shaft
13 7091917 1 NUT, 7/16-14, Hex Nyloc 1 per side
14 7091681 6 BOLT, 5/16-18 x 1” Hex Flange Lock 3 per side
15 7090815 24 SCREW, 3/8-16 x 3/4” Hex Washer Self-Tap 12 per side
16 7091905 26 BOLT, 5/16-18 x 7/8” Hex Flange Lock
17 7091811 22 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 11 per side
18 7091299 21 NUT, 3/8-16 Hex Nyloc 8 on left side
19 7027198 12 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5 2 on left side
20 7091601 53 NUT, 5/16-18 Hex Flange Lock, GR 5 16 on left side
21 7029263 2 SLEEVE, Suspension 1 per side
22 7090721 2 BOLT, 5/16-18 x 1/2” Hex Flange Lock
23 7035496 2 BEARING, .750 I.D.
24 7012068 1 RING, Blue
25 7026737 1 FLEX TUBE, 1.75 x 1.75 x 12”
26 7058912 1 ASSEMBLY, Air Filter (Includes Ref. #'s 27 thru 34)
27 7073435 1 RESTRICTER, Air Cleaner
28 7073436 1 PRECLEANER, Air Filter
29 7073437 1 HOUSING, Air Filter
30 7073438 1 BRACKET, Air Filter Mounting
31 7073439 1 ELEMENT, Air Filter
32 7073440 1 VALVE, Air Filter Drain
33 7073443 1 CAP, Air Filter
34 7073488 4 CLAMP, Hose
tionItem Qt
Note
painted part
painted part
Footnotes:
SERIES 1
37
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
REAR FRAME GROUP, RH
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
38
SERIES 1
REAR FRAME GROUP, RH
p
y
Part No Descri
35 7073002 1 ROD, Transmission Shift (3/8-16 thread)
36 7024159 2 COTTER PIN, 3/8 Self Lock
37 7072495 1 SWIVEL, 3/8 w/thru hole
38 7028036 2 SPRING, Friction Pack
39 7090122 7 WASHER, 3/8” SAE Flat
tionItem Qt
Note
Footnotes:
SERIES 1
39
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
BRAKE ASSEMBLY
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
40
SERIES 1
BRAKE ASSEMBLY
p
y
Part No Descri
1 7058751 1 BRAKE ASSEMBLY, Utility Vehicle (incl. items 2 thru 8)
2 7058683 1 WELDMENT, Rear CVT Brake Shaft
3 7072986 2 SPRING, CVT Brake
4 7073015 2 BRAKE SWIVEL, w/.531 Thru Hole
5 7091299 2 NUT, 3/8-16 Hex Nyloc or 7076979
6 7073116 2 BRACKET, Swivel Retainer (Red) 7063361, green version of
7 7092055 2 SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 5
8 7091293 4 SCREW, 1/4-20 x 3/8” Hex Washer Self-Tap
9 7072645 2 BEARING, 1” I.D.
10 7012709 2 RING, 1.00 Dia. External Retaining
11 7016561 2 BUSHING, 14 Gage Machine
12 7079295 3 NUT, 1/2-20 Hex Nyloc
13 7091508 4 BOLT, 5/16-18 x 3/4” Short Square Neck Carriage, GR 5
14 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR 5
15 7027230 6 SCREW, 1/4-20 x 1” Hex Head Cap, GR 5
16 7091603 2 NUT, 1/4-20 Hex Nyloc
17 7073097 1 PAWL, Park Brake
18 7073098 1 BRACKET, LH Park Brake Pawl Pivot (Black)
19 7073099 1 BRACKET, RH Park Brake Pawl Pivot (Black)
20 7073100 2 SPACER, Park Brake
21 7011224 2 SPRING, Return, Extension was 7072550 (voided)
22 7090299 1 SCREW, #10-32 x 1” Hex Washer Self-Tap
23 7091801 1 NUT, #10-32 Hex Center Lock
24 7073013 2 PIN, Brake Anchor
25 7071953 2 RETAINING RING, 5/8” Shaft
26 7090559 1 NUT, 1/2-20 Hex Jam, GR 5 or B
27 7072985 2 BRAKE ROD, Rear CVT (1/2-20 thread)
28 7027941 1 CABLE, Parking Brake
29 7072989 1 ROD, Lower CVT Brake (1/2-20 thread, both ends) also shown on FRONT FRAME
tionItem Qt
Note
7073116 not used in production
GROUP- Final Assembly page
Footnotes:
SERIES 1
41
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
DRIVE BASE GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
42
SERIES 1
DRIVE BASE GROUP
p
y
Part No Descri
1 7046206 1 WELDMENT, Drive Base also shown on REAR FRAME
2 7073106 2 CHANNEL, Subframe Connect
3 7091811 12 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
4 7091601 18 NUT, 5/16-18 Hex Flange Lock, GR 5
5 7074227 4 BRACKET, Transmission Mount w/Sq. Holes (Black) was 7074015
6 7091508 12 BOLT, 5/16-18 x 3/4” Short Square Neck Carriage, GR 5
7 7092041 4 SCREW, M16 x 2 x 35MM Hex Head Cap
8 7092042 4 WASHER, 16MM Split Lock
9 7073470 2 SPRING, Brake Return
10 7091602 2 BOLT, 5/16-18 x 1-1/2” Hex Flange Lock, GR 5
11 7091528 6 WASHER, .375 x .875 x .083 Flat
12 7091298 2 NUT, 5/16-18 Hex Nyloc
13 -- 1 * ENGINE, B&S 16 HP Vanguard Mod. 305447-0110-E1 (not
shown)
13 -- 1 * ENGINE, B&S 16 HP w/Generator Mod. 30544A-0111-E1
(shown)
14 7091609 2 SCREW, 5/16-24 x 1-1/2 Hex Head Cap, GR 5
15 7090187 8 WASHER, 5/16” Split Lock
16 7091297 4 NUT, 5/16-24 Hex, GR 5 or B
17 7072970 1 CLUTCH, CVT Drive
17 7100131 1 CLUTCH, CVT Drive upgraded 7072970
18 7092130 1 SCREW, 7/16-20 x 4-1/2” Hex Head Cap, GR 5
19 7091301 1 WASHER, 7/16” Split Lock
20 7072935 1 BELT, CVT (Cogged; 58.15 effective length) Dayco #1-7741
21 7071764 1 TORQUE BRACKET, Utility Vehicle
22 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
23 7091299 1 NUT, 3/8-16 Hex Nyloc
24 7035651 1 ANCHOR, Throttle
25 7092050 1 SCREW, #10-32 x 1/2” Pan Head, Phillips
26 7090601 1 WASHER, #10 External Tooth Lock
27 7029378 1 THROTTLE PLATE, B&S Vanguard
28 7092121 1 SCREW, #10-32 x 1/2” Hex Head Shoulder UVG & UVGT (or UVGC)
29 7072812 1 TRANSAXLE, Tuff Torq KT35C
30 7027959 1 SPROCKET, # 35- 3/8 Pitch
31 7072971 1 PULLEY, CVT Drive
31 7100154 1 PULLEY, CVT Drive Part has splined bore to fit
32 7091029 1 SCREW, M10-1.5 x 60 Hex Head Cap (w/nyloc patch)
33 7012063 2 WASHER, Cone
34 7072982 1 SHIFT ARM, CVT
tionItem Qt
Note
GROUP, LH page
UV
UVG & UVGT (or UVGC)
Snapper p/n 7072812.
Footnotes:
Note: * Purchase engine components directly from the engine manufacturer dealer.
SERIES 1
43
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
DRIVE BASE GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
44
SERIES 1
DRIVE BASE GROUP
p
y
Part No Descri
35 7091028 1 SCREW, 7/16-20 x 2-1/4” Hex Head Cap, GR 5
36 7090991 3 WASHER, 7/16” Flat (Type A, Wide)
37 7090970 1 NUT, 7/16-20 Hex Top Lock
38 7050498 1 MUFFLER, 16 HP B&S Vanguard was 7036514
39 7036511 1 TAILPIPE, UV-2
40 3039123 1 MUFFLER CLAMP, 1-5/8”
41 7046898 1 THROTTLE LINK, B&S Vanguard UVG & UVGT (or UVGC)
42 7046972 1 BRACKET, Throttle Adjustment UVG & UVGT (or UVGC)
43 7029377 1 CABLE, Throttle, 16 HP Vanguard
44 7027497 1 CABLE, Throttle, Pedal, Powerlink UVG & UVGT (or UVGC)
45 7027498 1 THROTTLE, Remote, Powerlink UVG & UVGT (or UVGC); also
46 7091925 1 SCREW, M8-1.25 x 16, Hex Head Cap
47 7033693 1 HOSE, 1/4” I.D. x 17” Long Fuel (not shown)
tionItem Qt
Note
shown on SEAT PEDESTAL
GROUP- Frame page
Footnotes:
Note: * Purchase engine components directly from the engine manufacturer dealer.
SERIES 1
45
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
CVT AXLE GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
46
SERIES 1
CVT AXLE GROUP
p
y
Part No Descri
1 7027192 5 LUG NUT, 1/2-20 Hex also shown on FRONT
2 7032027 2 WASHER, .77 x 1.5 x .06 Flat
3 7035602 2 BEARING, 30mm x 62mm
4 7058642 2 ASSEMBLY, Coupling (incl. Ref. No. 16)
5 7050561 2 ASSEMBLY, Plate/Seal (Red) (incl. Ref. No. 17) was 7058650
6 7072960 1 WHEEL HUB, Rear
7 7072965 1 AXLE SUPPORT, CVT, Aluminum
8 7072975 1 AXLE, CVT
9 7090297 1 COTTER PIN, 1/8 x 1-1/2
10 7091299 4 NUT, 3/8-16 Hex Nyloc
11 7091778 1 WOODRUFF KEY, #808
12 7092052 4 SCREW, 3/8-16 x 5-1/2” Hex Head Cap, GR 5
13 7092038 1 NUT, 3/4-16 Slotted Hex
14 7092045 2 SNAP RING, 30mm
15 7092046 2 WASHER, 1-3/16 x 1-5/8 x .06 Flat
16 7013864 1 LUBE FITTING, 3/16” Serrated
17 7073008 1 SEAL, 1.181 I.D., 1.850 O.D., .237 Thick
tionItem Qt
Note
SUSPENSION & WHEEL
GROUP pages
Footnotes:
SERIES 1
47
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
BED ASSEMBLY (Dump Bed)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
48
SERIES 1
BED ASSEMBLY (Dump Bed)
p
y
Part No Descri
1 7075881 1 BED, Plastic
2 7043202 2 BRACKET, Latch LH
3A 7026456 2 * LANYARD, Tailgate (1 pin & 1 hole end)
3B 7043321 2 LANYARD, Tailgate (2 pin ends)
4 7090037 2 COTTER PIN, 3/32 x 3/4”
5 7090606 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock
6 7033795 2 BUMPER, Recess Style
7 7092106 2 SCREW, #10 x 5/8” HiLo Nail Point
8 7091076 2 WASHER, .34 x .69 x .08 Flat
9 7026779 1 ROD, Tailgate
10 7010776 2 RETAINING RING, 1/2”, Heavy Duty
11 7091733 2 WASHER, .5 x 1.0 x .03 Flat
tionItem Qt
Note
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 50028699 and UV Serial #'s 50029300 thru 50029399.
SERIES 1
49
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
BED ASSEMBLY (Tail Gate)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
50
SERIES 1
BED ASSEMBLY (Tail Gate)
p
y
Part No Descri
1 7075882 1 TAILGATE, Plastic
2A 7043204 1 * COVER, Tailgate
2B 7043212 1 COVER, Tailgate
3 7027803 2 * BRACKET, Gate (weldment)
4 7090037 4 COTTER PIN, 3/32 x 3/4”
5 7090606 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock
6 7034792 2 LATCH, Tailgate
7 7092106 4 SCREW, #10 x 5/8” HiLo Nail Point
8 7091076 6 WASHER, .34 x .69 x .08 Flat
9 7091627 8 WASHER, .281 x 1.00 x .125 Flat
10 7091603 8 NUT, 1/4-20 Hex Nyloc
11 7023682 2 REFLECTOR, Red
12 7091256 8 SCREW, 1/4-20 x 2-1/4” Hex Head Cap, GR 5
tionItem Qt
Note
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 50028699 and UV Serial #'s 50029300 thru 50029399.
SERIES 1
51
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
BED ASSEMBLY (Latch)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
52
SERIES 1
BED ASSEMBLY (Latch)
p
y
Part No Descri
1 7022241 1 WELDMENT, Bed Frame
2 7091501 15 SCREW, 3/8-16 x 2-1/2” Hex Head Cap, GR 5
3 7091044 4 SCREW, 3/8-16 x 3-1/4”, Hex Head Cap, GR 5
4 7091811 5 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
5 7090122 19 WASHER, 3/8” SAE Flat
6 7090118 19 WASHER, 3/8” Split Lock
7 7091302 19 NUT, 3/8-16 Hex, GR 5 or B
8 7091518 1 NUT, 3/8-24 Hex Nyloc
9 7034564 1 ASSEMBLY, Rod-Link (incl. 1 each of items 10, 11 & 12)
10 7034524 1 ROD-LINK (1/4-28 thread)
11 7090095 1 NUT, 1/4-28 Hex, GR 5 or B
12 7015753 1 BALL JOINT, 1/4-28
13 7091733 1 WASHER, .5 x 1.0 x .03 Flat
14 7090095 1 NUT, 1/4-28 Hex, GR 5 or B
15 7091314 1 WASHER, 1/4” Internal Tooth Lock
16 7014981 1 BOLT, 3/8-24 Hex Flange Shoulder, GR 8
17 7028206 1 HANDLE, Bed Latch
18 7091629 3 COTTER PIN, .06 x .50
19 7091294 3 WASHER, .28 x .63 x .06 Flat
20 7092052 2 SCREW, 3/8-16 x 5-1/2” Hex Head Cap, GR 5
21 7029360 1 SPRING, Extension
22 7028262 1 HOOK, Bed (weldment)
23 7091299 2 NUT, 3/8-16 Hex Nyloc
24 7034437 1 ROD, Link
25 7034428 1 HOOK, Bed Ass'y (weldment)
tionItem Qt
Note
Footnotes:
SERIES 1
53
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WHEEL GROUP (TURF & TRAIL TIRE)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
54
SERIES 1
WHEEL GROUP (TURF & TRAIL TIRE)
p
y
Part No Descri
1 7063254 2 ASSY, Front Wheel, Turf Tire (incl. Ref. #'s 2, 3 & 4) used on UV & UVG
2 7073568 1 RIM, 12 x 7.00 w/ 1.06 Inset
3 7073005 1 TIRE, Titan Multi Trac C/S, 23 x 8.50-12
4 7012234 4 AIR VALVE (Snap-In)
5 7050532 1 ASSY, Left Front Wheel (incl. Ref #'s 4, 6 & 7) used on UVGT or UVGC
6 7078080 1 RIM, 10 x 6 w/1.06 Offset
7 7073194 1 TIRE, ATV 22 x 11 - 10 (Dirt Dog) Kenda Tire
8 7050533 1 ASSY, Right Front Wheel (incl. Ref. #'s 4, 6 & 7) used on UVGT or UVGC
9 7027192 20 LUG NUT, 1/2-20 Hex (tapered seat) also shown in Front Suspension
10 7073120 2 DUST CAP
11 7063257 2 ASSY, Rear Wheel, Turf Tire (incl. Ref. #'s 4, 12 & 13) used on UV & UVG
12 7073569 1 RIM, 12 x 8.50 w/ .95 Offset
13 7072888 1 TIRE, Titan Multi Trac C/S, 26 x 12.00-12, 4P
14 7050530 1 ASSY, Left Rear Wheel (incl. Ref. #'s 4, 15 & 16) used on UVGT or UVGC
15 7078081 1 RIM, 10 x 6 w/1.25 Offset
16 7073195 1 TIRE, ATV 25 x 12 - 10 (Dirt Dog) Kenda Tire
17 7050531 1 ASSY, Right Rear Wheel (incl. Ref. #'s 4, 15 & 16) used on UVGT or UVGC
tionItem Qt
Note
and CVT Axle Groups
Footnotes:
SERIES 1
55
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
ROPS/ACCESSORY GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
56
SERIES 1
ROPS/ACCESSORY GROUP
p
y
Part No Descri
1 7058752 1 WELDMENT, ROPS
2A 7044936 1 * HEAT SHIELD, Cab (UV-2)
2B 7043288 1 HEAT SHIELD (Red)
2B 7043289 1 HEAT SHIELD (Green)
3A 7073024 1 * SHIELD, Heat/Debris (Red)
3A 7063349 1 * SHIELD, Heat/Debris (Green)
3B 7043290 1 HEAT SHIELD, Top (Red)
3B 7043291 1 HEAT SHIELD, Top (Green)
4 7091640 12 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
5 7091299 12 NUT, 3/8-16 Hex Nyloc
6 7091541 2 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
7 7091905 2 BOLT, 5/16-18 x 7/8” Hex Flange Lock
8 7091298 2 NUT, 5/16-18 Hex Nyloc
tionItem Qt
Note
Footnotes:
Note: * Used on UVG Serial #'s 50028650 thru 50028699 and UV Serial #'s 50029300 thru 50029399.
SERIES 1
57
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
BRUSH GUARD GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
58
SERIES 1
BRUSH GUARD GROUP
p
y
Part No Descri
1 7078211 1 BRUSH GUARD (weldment) used on UVGT (or UVGC)
2 7090659 4 BOLT, 3/8-16 x 1-1/4” Hex Flange Lock
3 7076979 4 NUT, 3/8-16 Hex Nyloc
tionItem Qt
Note
Footnotes:
SERIES 1
59
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WINCH GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
60
SERIES 1
WINCH GROUP
p
y
Part No Descri
1 7043274 1 WINCH, Warner 2.5 C.I. Warner p/n 70250
2 7027516 1 SWITCH, Throttle Interlink (NO)
3 7092134 2 SCREW, #6-32 Truss Head, Slotted
4 7011274 6 BOOT, Terminal Winch
5 7043279 1 WIRE, Yellow, 6 Ga. 71” long Warner p/n 70246 (winch cable)
6 7043286 1 WIRE, Blue, 6 Ga. 71” long Warner p/n 70247 (winch cable)
7 7043275 1 WIRE, Black, 6 Ga. 18” long Warner p/n 70243 (winch cable)
8 7043277 1 WIRE, Red, 6 Ga. 18” long Warner p/n 70244 (winch cable)
9 7091576 4 NUT, 1/4-20 Hex
10 7090052 4 WASHER, 1/4” Split Lock
11 7032029 4 WASHER, 1/4” Flat
12 7091814 4 SCREW, 1/4-20 x 1-1/4” Hex Head Cap
13 7043280 1 CONTACTOR, 12V Winch Warner p/n 70251
14 7091584 4 NUT, 1/4-20 Hex Flange Lock, GR 5
15 7043276 1 KIT, Winch Hook Warner p/n 70242 (incl. hook,
16 7027168 4 SCREW, 5/16-18 x 1” Hex Head Cap, GR 5
17 7091098 4 WASHER, .31 x .75 x .08 Flat
18 7091315 4 WASHER, .32 x .58 x .08 Split Lock
19 7092135 2 NUT, #6-32 Hex Nyloc
20 7074326 1 THROTTLE ANCHOR, Front also shown on FRONT FRAME
21 7074319 1 WELDMENT, Power Generator End Cap, LH (Green) also shown on SEAT
22 7091541 2 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
23 7090624 2 BOLT, #10-24 x 3/4” Hex Flange Lock
24 7043281 1 ASSEMBLY, Remote Socket w/Harness Warner p/n 70252
25 7091290 2 NUT, #10-24 Hex Nyloc
26 7011259 1 SWITCH, Momentary Rocker (On-Off-On)
27 7078259 1 WIRING HARNESS, Winch
-- 7078260 1 WINCH HARNESS, Main component of 7078259
-- 7078261 1 WINCH HARNESS, Dash component of 7078259
28 7091299 2 NUT, 3/8-16 Hex Nyloc
29 7043273 1 ASSEMBLY, Winch Fairlead Warner p/n 70241
30 7091923 2 BOLT, 3/8-16 x 3/4” Square Neck Carriage
tionItem Qt
Note
clevis pin, cotter pin & strap)
GROUP- Final Assembly (item
12)
PEDESTAL GROUP- Frame
Footnotes:
SERIES 1
61
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
DECAL GROUP (Snapper)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
62
SERIES 1
DECAL GROUP (Snapper)
p
y
Part No Descri
1 7028043 1 DECAL, Turf Cruiser, LH
2 7028044 1 DECAL, Turf Cruiser, RH
3 7029361 1 DECAL, Trail Cruiser, LH
4 7029362 1 DECAL, Trail Cruiser, RH
5 7011252 1 HOOD DECAL, SNAPPER LH
6 7011253 1 HOOD DECAL, SNAPPER RH
7 7029364 1 DECAL, Turf, Front
8 7011256 1 DECAL, Grill (Turf Cruiser)
9 7011257 1 DECAL, Grill (TrailCruiser)
10 7072688 1 DECAL, Light Switch
11 7078295 1 DECAL, Winch Switch
12 7072687 1 DECAL, Bed Lift
13 7022228 1 DECAL, Powerlink used on UVG1621BV UV2
14 7078172 1 DECAL, Powerlink, Generator
tionItem Qt
Note
w/Powerlink
Footnotes:
SERIES 1
63
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
DECAL GROUP (Continued)
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
64
SERIES 1
DECAL GROUP (Continued)
p
y
Part No Descri
1 7024560 1 DECAL, Warning Avoid Injury or Death
2 7073504 1 DECAL, Warning- To Prevent Fire
3 7073476 1 DECAL, Warning- Off Road Use Only
4 7034810 1 DECAL, Console
5 7075377 1 DECAL. Transport Warning
6 7073473 1 DECAL, Danger ROPS
7 7073675 1 DECAL, Fuse Box, Utility Vehicle
8 7073506 1 DECAL, Warning- Hitch Load
9 7029985 1 DECAL, Warning, B&S Powerlink UVG & UVGT
10 7073477 1 DECAL, Warning- Hot Surface
11 7073505 1 DECAL, Specs & Maintenance
12 7011289 1 DECAL, Emissions, Vanguard not shown
tionItem Qt
Note
Footnotes:
SERIES 1
65
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
ELECTRICAL GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
66
SERIES 1
ELECTRICAL GROUP
p
y
Part No Descri
1 7021642 1 HOUR/TACH METER, Inductive was 7011217
1 7044636 1 HOUR/Tachometer
2 7019326 1 WIRE, Positive 17” used on UV1621BV
3 7022231 1 SWITCH, DP NO/NO, Snap-In
4 7023187 1 SWITCH- Rocker SPST
5 7024649 9 WIRE TIE, 11 Inch Std Black Nylon
6 7026570 1 SENSOR, Speed
7 7028570 2 RELAY, OPC E.C.
8 7028583 1 INTERLOCK, UV2, B&S
9 7029163 1 * WIRING HARNESS, UV2 Generator
10 7033898 1 GAGE PACKAGE, Speed/Gas
11 7027333 1 CABLE, Battery, Positive, 24” w/terminal cover was 7035607
12 7035659 1 SWITCH, Lights
13 7041595 1 * OUTLET, Utility Vehicle
14 7044672 1 * ELECTRIC CORD with Plug
15 7072684 1 SWITCH, Ignition
16 7072720 1 * INVERTER BOX, 120 VAC Powerlink Briggs part no. 695981 rev. J
16 7100460 1 * INVERTER, Powerlink Briggs part no. 790045
17 7072830 2 HEADLIGHT
18 7073090 1 OUTLET, 12 Volt DC Power
19 7073962 1 CABLE, Battery Ground, Black 23.0” 6 GA
20 7075671 1 SOLENOID, RER, Super-Trombetta used on UV1621BV
21 7075911 1 BATTERY, 11 Plate 375CCA - Wet
22 7090053 2 WASHER, 1/4” Internal Tooth Lock used on UV1621BV
23 7090376 4 NUT, #10-32 Hex Nyloc 2 for 7041595, Electrical Outlet
24 7091075 2 SCREW, #10-24 x 5/8” Hex Washer Flange Self-Tap attaches relay
25 7091240 4 SCREW, #10-32 x 5/8 Hex Washer Head Machine 2 for 41595, Electrical Outlet
26 7091286 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap, SEMS not shown; goes to battery
27 7091576 2 NUT, 1/4-20 Hex used on UV1621BV
28 7092013 2 * SCREW, Thread Rolling Tapping
29 7092014 1 * GASKET, Drop Cord/Inverter (B&S # 807091)
30 7092020 1 * CLAMP, Drop Cord Tie Down
31 1709188 1 PLUG, Dash Hole
32 7091199 6 NUT, 1/4 Nylon Non-Threaded
33 7073406 1 KEY SET (2), G.C. Ignition in hardware bag
34 7090372 2 NUT, 1/4-20 Hex Center Lock, GR 5 or B in hardware bag
35 7091294 2 WASHER, .28 x .63 x .06 Flat in hardware bag
tionItem Qt
Note
terminals
Footnotes:
Note: * Used on UVG & UVGT (or UVGC) UV2 w/Powerlink
SERIES 1
67
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
ELECTRICAL GROUP
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
68
SERIES 1
ELECTRICAL GROUP
p
y
Part No Descri
36 7090072 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5
37 7027516 1 SWITCH, Throttle Interlink (NO) used on UVG1621BV &
tionItem Qt
Note
UVGC621BV UV2 w/Powerlink
Footnotes:
Note: * Used on UVG & UVGT (or UVGC) UV2 w/Powerlink
SERIES 1
69
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WIRING HARNESS- UV & UVG Models
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
70
SERIES 1
WIRING HARNESS- UV & UVG Models
p
y
Part No Descri
1 7073639 1 WIRING HARNESS, UV2, Main incl. 7078294 (dash harness);
2 7073678 1 WIRING HARNESS, UV2, Speed/Fuel incl. 7078291 (speedometer
3 7073819 1 WIRING HARNESS, UV2, Tachometer incl. 7078258 (tach dash
tionItem Qt
Note
7078293 (main harness); &
7078292 (console harness)
main harness) & 7078290
(speedometer dash harness)
harness) & 7078257 (tach main
harness)
Footnotes:
SERIES 1
71
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WIRING HARNESS- UVGT (UVGC) Model
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
72
SERIES 1
WIRING HARNESS- UVGT (UVGC) Model
p
y
Part No Descri
1 7073639 1 WIRING HARNESS, UV2, Main incl. 7078294 (dash harness);
2 7073678 1 WIRING HARNESS, UV2, Speed/Fuel incl. 7078291 (speedometer
3 7073819 1 WIRING HARNESS, UV2, Tachometer incl. 7078258 (tach dash
4 7078259 1 WIRING HARNESS, Winch incl. 7078260 (winch main
tionItem Qt
Note
7078293 (main harness); &
7078292 (console harness)
main harness) & 7078290
(speedometer dash harness)
harness) & 7078257 (tach main
harness)
harness) & 7078261 (winch
dash harness)
Footnotes:
SERIES 1
73
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WIRING SCHEMATIC- UV Model
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
74
SERIES 1
WIRING SCHEMATIC- UV Model
p
y
Part No Descri
-- -- 1 Wiring Schematic incl. harnesses 7073639, 7073678 & 7073819
tionItem Qt
Note
Footnotes:
SERIES 1
75
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WIRING SCHEMATIC- UVG Model
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
76
SERIES 1
WIRING SCHEMATIC- UVG Model
p
y
Part No Descri
-- -- 1 Wiring Schematic incl. harnesses 7073639, 7073678 & 7073819
tionItem Qt
Note
Footnotes:
SERIES 1
77
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
WIRING SCHEMATIC- UVGT (UVGC) Model
Manual No. 7006179 TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
78
SERIES 1
WIRING SCHEMATIC- UVGT (UVGC) Model
p
y
Part No Descri
-- -- 1 Wiring Schematic incl. harnesses 7073639, 7073678 & 7073819
tionItem Qt
Note
Footnotes:
SERIES 1
79
Manual No. 7006179TURF / TRAIL CRUISER
TP 400-5042-2-GC-N
Parts Manual fo
r
TURF / TRAIL CRUISER
UTILITY VEHICLE
SERIES 1
IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY
OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS
Briggs & Startton Yard Power Products Group
Copyright © 2007
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
Revision 2,
McDonough, GA, 30253 U.S.A.
7/23/2007
Manual No. 7006179
TP 400-5042-2-GC-N
Loading...