Snapper SZT18426BVE, SZT20486BVE User Manual

Parts Manual fo

r

T

E

E

SCRAMBLER ZERO-TURN

42" & 48" HYDRO DRIVE SZ

SERIES 6

MODEL

SZT18426BV
SZT20486BV

COPYRIGHT ©2005
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.

Revision 1,

McDonough, GA, 30253 U.S.A.

7/28/2005

Manual No. 7006181

TP 400-5049-1-HZ-N

s

PAGE GROUP

4
6

8
10
12
16
20
22
26
30
32
36
38
40
42
44
46
48
50
52
54
56
58
60
62

CASTER, FRONT WHEEL & TIRE ASSEMBLY
WHEELS- REAR
42" FRONT FRAME & COVER ASSEMBLY
48" FRONT FRAME & COVER ASSEMBLY
REAR FRAME ASSEMBLY
FENDER & TRANSAXLE ASSEMBLY
OPERATOR SEAT & TANK
TWIN STICK CONTROL, R.H.
TWIN STICK CONTROL, L.H.
BRAKE/CLUTCH LEVER ASSEMBLY
ENGINE COMPONENTS
CLUTCH ASSEMBLY
42" DECK LIFT HANDLE ASSEMBLY
48" DECK LIFT HANDLE ASSEMBLY
42" MOWER DECK ASSEMBLY (Part 2)
42" MOWER DECK ASSEMBLY (Part 1)
42" MOWER DECK ASSEMBLY (Part 3)
48" MOWER DECK ASSEMBLY (Part 1)
48" MOWER DECK ASSEMBLY (Part 2)
42" SPINDLE ASSEMBLY
48" SPINDLE ASSEMBLY
DECALS
ELECTRICAL COMPONENTS (Part 1)
ELECTRICAL COMPONENTS (Part 2)
WIRING SCHEMATIC

Table Of Content

SERIES 6

Manual No. 7006181SCRAMBLER ZERO-TURN

3

TP 400-5049-1-HZ-N

CASTER, FRONT WHEEL & TIRE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

4

SERIES 6

CASTER, FRONT WHEEL & TIRE ASSEMBLY

p

y

Part No Descri

1 7059090 2 ASSEMBLY, Front Wheel & Tire (Complete) (Includes Items 2

thru 5)
2 7035618 1 TIRE, 11 x 4.00-5, Smooth Tread per front wheel & tire assembly
3 7039477 1 RIM, 5.00 Dia. x 3.00 per front wheel & tire assembly
4 7076998 1 LUBE FITTING, 1/4-28 Thread Forming Was 29275, per front wheel &

5 7012234 1 VALVE STEM, Air (Snap-in) per front wheel & tire assembly
6 7012709 2 RING, 1” External Retaining
7 7023556 4 BUSHING, Caster Was 46626
8 7013864 2 LUBE FITTING, Straight (press-fit for .187 dia. Hole)
9 7041783 2 WELDMENT, Pivot Yoke, Caster

10 7090839 2 NUT, 7/16-14 Hex Center Lock, GR 5 or B
11 7035359 2 TUBE, 5/8 O.D. x 14 Ga x 4.51
12 7035358 4 BEARING, Ball, 5/8 x 1-3/8”
13 7091772 2 SCREW, 7/16-14 x 6” Hex Head Cap, GR5

tionItem Qt

Note

tire assembly

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

5

TP 400-5049-1-HZ-N

WHEELS- REAR

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

6

SERIES 6

WHEELS- REAR

p

y

Part No Descri

1 7058948 2 ASSEMBLY, Rear Tire & Rim, 18 x 8.50-8 Multi-Trac (Incl items

2A, 3A & 7)

-- 7058959 2 ASSEMBLY, Rear Tire & Rim, 18 x 9.50-8 Multi-Trac (Incl items
2B, 3B & 7)

2A 7046322 1 TIRE, 18 x 8.50-8, Multi-Trac per rear wheel & tire assembly
2B 7072706 1 TIRE, 18 x 9.50-8, Multi-Trac Was 46339, per rear wheel &

3A 7039468 1 RIM, 18 x 8.50 w/25mm Hub per rear wheel & tire assembly
3B 7039468 1 RIM, 18 x 8.50 w/ 25mm Hub per rear wheel & tire assembly

4 7072028 2 WASHER, 1.56 x 1.054 x .047 Flat
5 7091764 2 KLIPRING, 1” External Waldes Truarc #5304-100
6 7011022 2 HUB CAP, Polyethylene
7 7012234 1 VALVE STEM, Air (Snap-in) per rear wheel & tire assembly
8 7042940 2 KEY, Square M6 x 38mm

tionItem Qt

Note

used in SZT18426BVE

used in SZT20486BVE

tire assembly

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

7

TP 400-5049-1-HZ-N

42" FRONT FRAME & COVER ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

8

SERIES 6

42" FRONT FRAME & COVER ASSEMBLY

p

y

Part No Descri

1 7059380 1 WELDMENT, Front Frame Series #3
2 7075910 1 PLATE, Footrest Support
3 7090595 6 BOLT, 5/16-18 x 3/4” Hex Flange Lock
4 7091601 5 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
5 7028260 2 FASTENER, “U” Type
6 7090324 2 SCREW, 3/8-16 x 1” Hex Washer Self-tap
7 7090517 2 WASHER, 3/8” FLAT (wide)
8 7035375 2 SPACER, Front Frame Pivot

9 7035374 1 PLATE, Front Frame Slip
10 7075841 1 FLOOR PAN, HOZ
11 7075219 1 FOOTREST, HOZ
12 7091890 4 WASHER, 1/4” Internal/External Lock
13 7023341 2 KNOB (1/4-20 thread)
14 7075885 1 MAT, Floor
15 7041818 3 PAD, Floor Board Support
16 7075993 1 DECAL, Warning, Read Manuals & Instructions see decal page
17 7046426 1 DECAL, Deck Height see decal page
18 7071916 1 DECAL, SNAPPER (14.56” long)

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

9

TP 400-5049-1-HZ-N

48" FRONT FRAME & COVER ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

10

SERIES 6

48" FRONT FRAME & COVER ASSEMBLY

p

y

Part No Descri

1 7059380 1 WELDMENT, Front Frame Series #3

2 7075910 1 PLATE, Footrest Support

3 7090595 6 BOLT, 5/16-18 x 3/4” Hex Flange Lock

4 7091601 5 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070

5 7028260 2 FASTENER, “U” Type

6 7090324 2 SCREW, 3/8-16 x 1” Hex Washer Self-tap

7 7090517 2 WASHER, 3/8” FLAT (wide)

8 7035375 2 SPACER, Front Frame Pivot

9 7035374 1 PLATE, Front Frame Slip
10 7075841 1 FLOOR PAN, HOZ
11 7075219 1 FOOTREST, HOZ
12 7091890 4 WASHER, 1/4” Internal/External Lock
13 7023341 2 KNOB (1/4-20 thread)
14 7075885 1 MAT, Floor
15 7041818 3 PAD, Floor Board Support
16 7075993 1 DECAL, Warning, Read Manuals & Instructions
17 7046426 1 DECAL, Deck Height see decal page
18 7071916 1 DECAL, SNAPPER (14.56” long)
19 7047099 2 BRACKET, Saddle- Front
20 7091573 4 BOLT, 1/4-20 x 5/8” Short Neck Carriage, GR 5 Was 90551
21 7091584 6 NUT, 1/4-20 Hex Flange Lock Was 90583
22 7059240 1 WELDMENT, Front Lift, 48
23 7022717 1 ROD, Deck Support
24 7017847 1 RING, .438 External Retaining
25 7047060 1 WELDMENT, Rear Lift
26 7074256 1 TIMING ROD (1/2-13 thread)
27 7091598 1 COTTER PIN, 1/8 x 1” Was 90041
28 7090667 4 WASHER, 1/2” Flat
29 7046599 1 SWIVEL, .50 Thru Hole
30 7091894 1 NUT, 1/2-13 Hex Center Lock, GR 5
31 7091947 1 HAIR PIN, 1/8” Dia. x 1/2”
32 7090250 2 WASHER, 1/2” SAE Flat

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

11

TP 400-5049-1-HZ-N

REAR FRAME ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

12

SERIES 6

REAR FRAME ASSEMBLY

p

y

Part No Descri

1 7046991 1 WELDMENT, Rear Frame

2 7035368 2 CUSHION, Seat Support

3 7035369 2 SPRING, Seat Support

4 7090999 2 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)

5 7090731 2 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR 5 Was 90004

6 7075630 1 HINGE, Seat

7 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070

8 7033587 1 BUMPER, Rear

9 7091506 4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap
10 7091587 1 WASHER, .531 x 1.062 x .121 SAE Flat
11 7090975 1 NUT, 1/2-13 Hex Center Lock, GR 5 or B

12A 7041793 1 WELDMENT, Battery Bracket used in SZT18426BVE
12B 7058238 1 WELDMENT, Battery Bracket used in SZT20486BVE

13 7013321 2 BUSHING, Tie Rod
14 7090238 4 SCREW, 5/16-24 x 1” Hex Head Cap, GR 5
15 7011791 4 RETAINER, 5/16” Bolt
16 7091315 4 WASHER, .32 x .58 x .08 Split Lock
17 7091297 4 NUT, 5/16-24 Hex, GR 5 or B
18 7011033 2 GROMMET
19 7010935 2 WASHER, 3/4” Flat
20 7091730 1 BOLT, 1/2-13 Hex Shoulder
21 7058728 1 WELDMENT, Idler Arm, Primary
22 7058692 1 SPRING, Extension- 5” long
23 7090122 3 WASHER, 3/8” SAE Flat
24 7091585 2 NUT, 3/8-16 Hex Center Lock, GR 5 or B
25 7024344 1 PULLEY, Idler, V 3.30 HA
26 7079832 1 BOLT, 3/8-16 x 4” Hex Head Cap, GR 5
27 7034937 1 BRACKET, Hydro Idler
28 7073428 1 SPRING, Hydro Idler
29 7091553 1 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
30 7039485 1 CABLE, Hydro Release Valve
31 7091240 2 SCREW, #10-32 x 5/8” Hex Washer Head Machine
32 7018574 1 IDLER, 4.12” Outside Diameter, Flat
33 7090376 2 NUT, #10-32 Hex Nyloc
34 7022886 1 SWITCH, Seat (NO/NC) Snap-In also shown on electronic

35 7075102 1 SLEEVE, Idler
36 7034938 1 GUIDE, Belt

tionItem Qt

Note

components page

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

13

TP 400-5049-1-HZ-N

REAR FRAME ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

14

SERIES 6

REAR FRAME ASSEMBLY

p

y

Part No Descri

37 7058691 1 COVER, Spring
38 7091272 4 FASTENER, Ratchet
39 7043858 2 BUSHING, Flange, .64 x .75 x .5
40 7072878 2 PLATE, Pivot
41 7091000 8 SCREW, 5/16-18 x 7/8” Pan Head Self-Tap (Torx)
42 7091601 8 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
43 7072907 2 WIREFORM, Control
44 7042485 2 WELDMENT, Bellcrank
45 7090841 1 PIN, 3/16 x 1-1/2” Roll

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

15

TP 400-5049-1-HZ-N

FENDER & TRANSAXLE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

16

SERIES 6

FENDER & TRANSAXLE ASSEMBLY

p

y

Part No Descri

1 7029128 1 TRANSAXLE, Hydro Eaton Model X778-005

2 7029129 1 TRANSAXLE, Hydro w/o Manifold R.H. Eaton Model X778-011

3 7015894 2 KEY, #605 Woodruff

4 7091122 8 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539

5 7035337 2 FAN, 6” O.D., 10 Blade

6 7035336 2 PULLEY, Hydro Input

7 7091771 2 RING, RR3100-66 External Retaining

8 7042773 1 V-BELT, HA Sect. 42.5” effective length Hydro Drive

9 7034915 2 BRACKET, Support, Fender
10 7034916 1 BRACKET, Support, Hydro
11 7091819 4 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap Was 90362
12 7034909 1 FENDER, Rear Frame, Left Hand
13 7034908 1 FENDER, Rear Frame, Right Hand
14 7034917 1 BRACKET, Deck Support, Left Rear used in SZT18426BVE
15 7035424 1 BRACKET, Deck Support, Right Rear used in SZT18426BVE
17 7091541 26 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap Was 90368
18 7090324 8 SCREW, 3/8-16 x 1” Hex Washer Self-tap
19 7073385 1 TRANSMISSION ROD, RH, Twin Stick return to neutral
20 7073419 1 TRANSMISSION ROD, LH, Twin Stick return to neutral
21 7091299 2 NUT, 3/8-16 Hex Nyloc
22 7039485 1 CABLE, Hydro Release Valve Rear Frame Asy pg item 30
23 7044767 2 DECAL, Hydro Reservoir see decal page
24 7039484 1 BRACKET, Cable, Hydro Release Valve
25 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
26 7039483 2 BRACKET, Actuator, Hydro Release Valve
27 7012114 2 BUSHING, Differential Link, Powdered Metal
28 7091841 2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap, GR 5
29 7073182 2 ARM, Direction Control- Hydro Transaxle
30 7091165 4 BOLT, 1/4-28 x 5/8” w/Nyloc Patch, GR 8
31 7090746 4 WASHER, 1/4” Belleville
32 7034914 2 ARM, Brake
33 7090122 6 WASHER, 3/8” SAE Flat
34 7073420 1 BRAKE ROD, RH (3/8-16 thread)
35 7073046 1 BRAKE ROD, L. H. (3/8-16 thread)
36 7091594 4 COTTER-PIN, 1/16" x 1.42" Self-Locking Was 24874
37 7024586 2 SWIVEL, Brake Link- PM

tionItem Qt

Note

Footnotes:

NOTE: Use Mobil 1 DTE 26 oil for hydro transaxle.

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

17

TP 400-5049-1-HZ-N

FENDER & TRANSAXLE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

18

SERIES 6

FENDER & TRANSAXLE ASSEMBLY

p

y

Part No Descri

38 7074511 2 SPRING, Brake Compression

tionItem Qt

Note

Footnotes:

NOTE: Use Mobil 1 DTE 26 oil for hydro transaxle.

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

19

TP 400-5049-1-HZ-N

OPERATOR SEAT & TANK

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

20

SERIES 6

OPERATOR SEAT & TANK

p

y

Part No Descri

1 7044897 1 SEAT, Milsco High Back

2 7046561 1 TETHER, Seat

3 7090999 6 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)

4 7058530 1 ASSEMBLY, Fuel Tank/L.H.Fender includes fuel cap (75748),

5 7075748 1 GAS CAP w/Screw Vent

6 7074835 1 FITTING, Dapco Dapco part number #11492

7 7012337 1 GROMMET

8 7075708 1 DIP TUBE

9 7058531 1 ASSEMBLY, R.H. Fender
10 7075617 2 ARM REST, HOZ
11 7058511 1 WELDMENT, Fuel Tank Support
12 7058513 1 WELDMENT, Fender Support
13 7075609 1 FENDER, L.H. Lower
14 7075610 1 FENDER, R.H. Lower
15 7075628 1 HEAT SHIELD, Engine
16 7091908 4 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5
17 7090188 4 WASHER, .34 x .69 x .08 Flat
18 7091298 4 NUT, 5/16-18 Hex Nyloc
19 7090361 4 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
20 7091542 8 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)
21 7090858 4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap
22 7034817 1 DECAL, SCRAMBLER see decal page
23 7071683 1 DECAL, Hydro Release see decal page
24 7075760 2 DECAL, SNAPPER see decal page

tionItem Qt

Note

grommet (12337), fitting (74835)
& tube (75708)

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

21

TP 400-5049-1-HZ-N

TWIN STICK CONTROL, R.H.

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

22

SERIES 6

TWIN STICK CONTROL, R.H.

p

y

Part No Descri

1 7074317 1 BRACKET, R.H. Tank Support

2 7074931 1 BRACKET, Speed Adjustment

3 7090999 7 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)

4 7035661 1 SPACER, PTO Switch also shown on electronic

5 7075884 1 SWITCH, PTO E.C. (Delta Part No. 6201-219) also shown on electronic

6 7072977 1 CONTROL, Throttle/Choke, B&S (60” long) not shown; used on

-- 7075449 1 CONTROL, Throttle B&S 16HP Single Intek (48” long) not shown; used on

7 7023655 1 LEVER, Throttle Control

8 7071921 1 RIVET, Plastic Snap

9 7073425 1 BRACKET, R.H. Console- Twin Stick used in SZT18426BVE

-- 7078024 1 BRACKET, R.H. Console, 48 SZT used in SZT20486BVE
10 7078049 1 DECAL, Throttle/Choke Control also shown on Decal page
11 7072851 1 SHAFT, Control, Twin Stick
12 7010739 2 RING, 5/8” External Reatining
13 7013874 2 BUSHING, 5/8 x 5/8” Bronze
14 7041566 1 WELDMENT, Twin Stick, RH
15 7091628 1 WASHER, .64 x .99 x .05 Flat
16 7023355 1 SWITCH, Park Brake (NC/NO) also shown on electronic

17 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
18 7024607 1 SWIVEL, 3/8-16 Internal Thread
19 7073421 1 CONTROL ROD (3/8-16 thread)
20 7091593 4 PIN, 3/8 Self Locking Cotter
21 7091553 3 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
22 7072686 1 BLOCK, Twin Stick Control
23 7012316 5 WASHER, 3/8” Flat
24 7091299 4 NUT, 3/8-16 Hex Nyloc
25 7091540 2 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
26 7074628 1 BRACKET, Handle Adjustment
27 7090188 2 WASHER, .34 x .69 x .08 Flat
28 7091298 2 NUT, 5/16-18 Hex Nyloc
29 7091813 2 SCREW, 1/4-20 x 1-3/4” Hex Head Cap, GR 5
30 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
31 7091603 2 NUT, 1/4-20 Hex Nyloc
32 7072831 1 HANDLE, Twin Stick
33 7072212 1 GRIP, Twin Stick
34 7074899 1 RETURN ROD (3/8-16 thread)
35 7072450 2 SPRING, Neutral Return

tionItem Qt

Note

components page

components page

SZT18426BVE

SZT20486BVE

components page

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

23

TP 400-5049-1-HZ-N

TWIN STICK CONTROL, R.H.

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

24

SERIES 6

TWIN STICK CONTROL, R.H.

p

y

Part No Descri

36 7071585 1 SWIVEL, Shoulder (5/16-18 thread)
37 7091601 1 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
38 7075031 1 DAMPENER, Hydraulic
39 7075026 1 SPACER, Twin Stick
40 7090872 1 BOLT, 1/4-20 x 1-1/8” Hex Flange Lock, GR 5
41 7090122 2 WASHER, 3/8” SAE Flat
42 7063252 1 CABLE, Choke (28” long) used in SZT20486BVE
43 7090390 1 WASHER, 3/8” Internal Tooth Lock used in SZT20486BVE
44 7091630 1 NUT, 3/8-24 Hex, GR 8 Was 90155 (used in

tionItem Qt

Note

SZT20486BVE)

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

25

TP 400-5049-1-HZ-N

TWIN STICK CONTROL, L.H.

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

26

SERIES 6

TWIN STICK CONTROL, L.H.

p

y

Part No Descri

1 7072866 1 BRACKET, L.H. Tank Support
2 7074931 1 BRACKET, Speed Adjustment
3 7090999 6 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)
4 7026343 1 SWITCH, Ignition (After-fire Solenoid) also shown on electronic

5 7023506 1 BEZEL also shown on electronic

6 7072952 1 DECAL, Ignition Switch also shown on Decal page
7 7075812 1 DECAL, Park Brake also shown on Decal page
8 7072941 1 BRACKET, Brake/Clutch Detent, Twin Stick

9 7072670 1 BRACKET, L.H. Console- Twin Stick
10 7012685 1 NUT, 5/8-32 Hex
11 7072851 -- SHAFT, Control, Twin Stick Ref: Twin Stick Control,

12 7010739 2 RING, 5/8” External Reatining
13 7013874 2 BUSHING, 5/8 x 5/8” Bronze
14 7041539 1 WELDMENT, Twin Stick, LH
15 7091628 1 WASHER, .64 x .99 x .05 Flat
16 7023355 2 SWITCH, Park Brake (NC/NO) also shown on electronic

17 7090913 4 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
18 7024607 1 SWIVEL, 3/8-16 Internal Thread
19 7073421 1 CONTROL ROD (3/8-16 thread)
20 7091593 4 PIN, 3/8 Self Locking Cotter
21 7091553 3 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
22 7072686 1 BLOCK, Twin Stick Control
23 7012316 5 WASHER, 3/8” Flat
24 7091299 4 NUT, 3/8-16 Hex Nyloc
25 7091540 2 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
26 7074628 1 BRACKET, Handle Adjustment
27 7090188 2 WASHER, .34 x .69 x .08 Flat
28 7091298 2 NUT, 5/16-18 Hex Nyloc
29 7091813 2 SCREW, 1/4-20 x 1-3/4” Hex Head Cap, GR 5
30 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
31 7091603 2 NUT, 1/4-20 Hex Nyloc
32 7072831 1 HANDLE, Twin Stick
33 77212 1 GRIP, Twin Stick
34 7074899 1 RETURN ROD (3/8-16 thread)
35 7072450 2 SPRING, Neutral Return
36 7071585 1 SWIVEL, Shoulder (5/16-18 thread)
37 7091601 1 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070

tionItem Qt

Note

components page

components page

R.H.page

components page

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

27

TP 400-5049-1-HZ-N

TWIN STICK CONTROL, L.H.

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

28

SERIES 6

TWIN STICK CONTROL, L.H.

p

y

Part No Descri

38 7075031 1 DAMPENER, Hydraulic
39 7075026 1 SPACER, Twin Stick
40 7090872 1 BOLT, 1/4-20 x 1-1/8” Hex Flange Lock, GR 5
41 7090122 2 WASHER, 3/8” SAE Flat
42 7091819 3 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap Was 90362

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

29

TP 400-5049-1-HZ-N

BRAKE/CLUTCH LEVER ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

30

SERIES 6

BRAKE/CLUTCH LEVER ASSEMBLY

p

y

Part No Descri

1 7075914 1 BUTTON, Park Brake

2 7035945 1 GRIP, Brake/Clutch Handle

3 7073452 1 ROD, Park Brake 10” arc radius

4 7035946 1 SPRING, Clutch/Brake Release

5 7035485 1 ARM, Brake/Clutch Lever

6 7035484 1 PIVOT, Brake/Clutch Lever

7 7091084 2 SCREW, 1/4-20 x 3/8” Hex Washer Self-Tap Was 91293

8 7072871 1 TUBE, Park Brake

9 7010694 1 BUSHING, Nylon
10 7073150 1 ROD, Brake Actuation
11 7052431 4 PIVOT, Foot Shaft Assy (weldment 23170 with grease fitting,

13864)
12 7090841 3 ROLL PIN, 3/16 x 1-1/2”
13 7029208 1 ARM, Brake/Clutch
14 7042614 1 WELDMENT, Brake/Clutch Arm
15 7090844 1 ROLL PIN, 3/16 x 3/4”
16 7091000 4 SCREW, 5/16-18 x 7/8” Pan Head Self-Tap (Torx)

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

31

TP 400-5049-1-HZ-N

ENGINE COMPONENTS

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

32

SERIES 6

ENGINE COMPONENTS

p

y

Part No Descri

1 -- 1 *ENGINE, 18HP B&S Intek, 3400 RPM Mod 31H777, Type 0117, Trim

-- -- 1 *ENGINE, 20HP ELS B&S 3500 RPM Mod 40G777, Type 0112, Trim

2 7010210 1 KEY, 1/4” Square x 2”
3A 7015352 2 ** GASKET, Exhaust 1.25” I.D.hole; mat'l graphite
3B 7014509 1 *** GASKET, Exhaust 1.18” I.D. hole; mat'l graphite

3C 7063283 2 *** GASKET, 20 HP Intec 1.00” I.D. Hole

4 7027972 1 ASSEMBLY, Oil Valve

5 7035362 1 GUIDE, Engine Belt

6 7036389 1 PLATE, Engine, HOZ

7 7040706 1 PULLEY, Engine

8 7090324 4 SCREW, 3/8-16 x 1” Hex Washer Self-tap engine mounting bolts

9 7091301 1 WASHER, 7/16 Split Lock
10 7091763 1 SCREW, 7/16-20 x 1-1/2” Hex Head Cap, GR 5
11 7091807 1 WASHER, .468 x 1.38 x .25 Flat (special)
12 7029900 4 CLAMP, Fuel Line Was 12222
13 7024161 2 BOLT, 5/16-18 x 4” Shoulder B&S #93927
14 7024566 1 SCREW LOCK
15 7041537 1 DEFLECTOR, Muffler SZT18426BVE
16 7071756 1 ** ADAPTER, Muffler Briggs p/n 695766
17 7074826 1 ** MUFFLER, 14.5 HP B&S Engine Nelson p/n 25482D
18 7091581 3 SCREW, #8-18 x 1/2” Hex Head Sheet Metal
19 7041340 1 ** WELDMENT, Heat Shield- B&S
20 7029982 1 HOSE, Fuel, 1/4 I.D. x 14” long qty. 1 on 18HP; qty. 2 on 20HP
21 7016325 1 VALVE, Fuel
22 7012638 1 ** HOSE, Fuel, 12-1/2” long Was 12912
23 7071765 1 *** HEAT SHIELD, Muffler, V-Twin
24 7091122 3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539
25 7090606 1 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5 Was 91510
26 7015861 1 HARNESS CLIP (vinyl covered)
27 7071760 1 ** HEAT SHIELD, Fender
28 7024241 1 *** MUFFLER, B&S 16HP Briggs p/n 394151
29 7026778 1 DEFLECTOR, Direct Out used with muffler 24241
30 7092025 4 *** WASHER, M8 Split Lock
31 7040000 1 *** MANIFOLD, 20 HP Intec
32 7091579 1 ** SCREW, 1/4-20 x 1/2” Hex Flange Lock, GR 5
33 7091738 2 SCREW, 5/16-18 x 3/4” Socket Head Cap, GR 8

tionItem Qt

Note

E1 (**)

E1 (***)

Footnotes:

*NOTE 1: Purchase engine components directly from engine manufacturer dealer.
**NOTE 2: used on SZT18426BVE
***NOTE: used on SZT20486BVE
*NOTE 1: Purchase engine components directly from engine manufacturer dealer.

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

33

TP 400-5049-1-HZ-N

ENGINE COMPONENTS

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

34

SERIES 6

ENGINE COMPONENTS

p

y

Part No Descri

34 7091584 3 NUT, 1/4-20 Hex Flange Lock

tionItem Qt

Note

Footnotes:

*NOTE 1: Purchase engine components directly from engine manufacturer dealer.
**NOTE 2: used on SZT18426BVE
***NOTE: used on SZT20486BVE
*NOTE 1: Purchase engine components directly from engine manufacturer dealer.

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

35

TP 400-5049-1-HZ-N

CLUTCH ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

36

SERIES 6

CLUTCH ASSEMBLY

p

y

Part No Descri

1 7091735 1 BOLT, 7/16-20 x 8” Hex Head, GR 5

2 7029138 2 WASHER, .468 I.D. x 1.50 O.D. x .188 Flat

3 7029136 2 BEARING, 6305 w/Snap Ring

4 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070

5 7029117 1 V-BELT, 5L Sect. Cog, 50.170” effective length used on 42” Deck models;

-- 7046997 1 V-BELT, 5L Sect. Cog, 49.44” effective length used on 48” Deck models;

6 7029107 1 PULLEY, Jackshaft used in SZT18426BVE

-- 7046892 1 PULLEY, Jackshaft used in SZT20486BVE

7 7091829 2 SCREW, 1/4-20 x 1/2” Set w/Patch

8 7063269 1 SUPPORT, Jackshaft- TG 2000

9 7091508 6 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
10 7029135 1 JACKSHAFT, 5.525” long
11 7013250 1 KEY 1/4” Square x 1”
12 7063248 1 BRACKET, Anti-Rotation- TG-2000
13 7063246 1 CLUTCH, Warner TG-2000 (12V)
14 7091301 1 WASHER, 7/16” Split Lock
15 7090460 1 NUT, 7/16-20 Hex, GR 5 or B
16 7012652 1 WIRE CLIP 7/16”, Vinyl Covered

17A 7029137 1 SPACER, Jackshaft used in SZT18426BVE
17B 7063247 1 SPACER, Jackshaft, Warner Clutch used in SZT20486BVE

tionItem Qt

Note

Primary Drive (Dayco #46-0364)

Primary Drive

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

37

TP 400-5049-1-HZ-N

42" DECK LIFT HANDLE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

38

SERIES 6

42" DECK LIFT HANDLE ASSEMBLY

p

y

Part No Descri

1 7041924 1 HANDLE, Deck Lift

2 7041925 1 BRACKET, Pivot Support

3 7058090 1 WELDMENT, Deck Lift Handle

4 7029040 1 WASHER - Slipper

5 7046489 1 SPRING, Torsion

6 7090072 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5

7 7091584 3 NUT, 1/4-20 Hex Flange Lock Was 90583

8 7035489 1 BAR, Deck Lift

9 7090122 3 WASHER, 3/8” SAE Flat
10 7091503 2 HAIR PIN, 3/32 x 1-1/2”
11 7013996 1 PIN, 3/8 x 2” Clevis
12 7058077 1 DETENT, Lift Handle
13 7091318 1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
14 7091601 5 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
15 7046457 1 DECAL, Deck Position
16 7091887 1 PIN, 3/8 x 1/2” Large Head Clevis
17 7046491 1 PIN, 3/8 x 1-5/8” Clevis
18 7046490 1 SPACER, Deck Lift
19 7091597 1 PIN, 3/32 x 3/4” Cotter
20 7091530 1 BOLT, 1/4-20 x 3/4” Short Neck Carriage, GR 5
21 7074768 2 GRIP, Deck Lift

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

39

TP 400-5049-1-HZ-N

48" DECK LIFT HANDLE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

40

SERIES 6

48" DECK LIFT HANDLE ASSEMBLY

p

y

Part No Descri

1 7041924 1 HANDLE, Deck Lift

2 7041925 1 BRACKET, Pivot Support

3 7058090 1 WELDMENT, Deck Lift Handle

4 7029040 1 WASHER - Slipper

5 7046489 1 SPRING, Torsion

6 7090072 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5

7 7091584 2 NUT, 1/4-20 Hex Flange Lock Was 90583

8 7047066 1 LINK, Connector

9 7090122 5 WASHER, 3/8” SAE Flat
10 7091503 2 HAIR PIN, 3/32 x 1-1/2”
11 7090667 2 WASHER, 1/2” Flat
12 7058077 1 DETENT, Lift Handle
13 7091318 1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
14 7091601 1 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
15 7046457 1 DECAL, Deck Position
16 7091887 1 PIN, 3/8 x 1/2” Large Head Clevis
17 7046491 1 PIN, 3/8 x 1-5/8” Clevis
18 7046490 1 SPACER, Deck Lift
19 7091597 2 PIN, 3/32 x 3/4” Cotter
20 7047067 1 PLATE, Connector Arm
21 7091948 2 PIN, 1/2 x .725 Clevis
22 7091598 2 COTTER PIN, 1/8 x 1” Was 90041
23 7013996 1 PIN, 3/8 x 2” Clevis
24 7074768 2 GRIP, Deck Lift
25 7091530 1 BOLT, 1/4-20 x 3/4” Short Neck Carriage, GR 5

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

41

TP 400-5049-1-HZ-N

42" MOWER DECK ASSEMBLY (Part 2)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

42

SERIES 6

42" MOWER DECK ASSEMBLY (Part 2)

p

y

Part No Descri

27 7090122 2 WASHER, 3/8” SAE Flat
28 7090289 1 NUT, 3/8-24 Hex Center Lock GR 5 or B shown on previous page only
29 7014241 1 WASHER, 1/4” Flat shown on previous page only
30 7042586 1 WELDMENT, Lift Arm, Front
31 7034815 1 LIFT ARM, Front
32 7010935 4 WASHER, 3/4” Flat
33 7015447 1 ECCENTRIC, Leveling
34 7090390 1 WASHER, 3/8” Internal Tooth Lock
35 7090163 1 SCREW, 3/8-24 x 1-1/4” Hex Head Cap w/Nylon Patch, GR 5
36 7035495 1 ROD, Cutter Deck Timing (3/8-16 thread)
37 7042585 1 WELDMENT, Lift Arm, Rear
38 7032028 2 WASHER, .781 x 1.5 x .132 Flat
39 7024586 1 SWIVEL, Brake Link- PM
40 7091310 1 HAIR PIN, #13 replaces 16231
41 7021815 1 SPACER, .391 I.D. x .531 long
42 7091585 1 NUT, 3/8-16 Hex Center Lock Was 90546

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

43

TP 400-5049-1-HZ-N

42" MOWER DECK ASSEMBLY (Part 1)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

44

SERIES 6

42" MOWER DECK ASSEMBLY (Part 1)

p

y

Part No Descri

1 7061958 1 DECK, 42” Replacement Includes welded deck and

2 7051914 2 ASSEMBLY, Spindle, Brake Was 59723

3 7091588 14 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR 5 Was 90612

4 7091619 18 NUT, 3/8-16 Hex Flange Lock Was 90613

5 7014407 2 WASHER, Spindle

6 7026691 2 BLADE, 21” Standard Lift

7 7012063 5 WASHER, .406 I. D. Cone

8 7090824 2 SCREW, 3/8-24 x 1-1/4” Hex Head Cap, GR 5

9 7033366 2 BRACE, Spindle
10 7027198 2 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5
11 7051747 2 ASSEMBLY, Spindle Lock components not sold separately
12 7044651 1 WELDMENT, Stationary Idler, 42 HOZ
13 7042811 1 REINFORCEMENT, 42” Deck, RH
14 7042812 1 REINFORCEMENT, 42” Deck, LH
15 7091547 4 BOLT, 3/8-16 x 3/4” Short Neck Carriage, GR 5 Was 90850
16 7035982 1 BRACKET, Right Front Lift, 42” Deck
17 7035983 1 BRACKET, Left Front Lift, 42” Deck
18 7035985 1 BRACKET, Left Rear Lift, 42” Deck
19 7036437 2 PULLEY, 5-1/4”
20 7074467 2 NUT, 3/4-16 Hex Jam, GR 8
21 7090872 1 BOLT, 1/4-20 x 1-1/8” Hex Flange Lock, GR 5
22 7010916 1 SPACER, .265 x .375 x .300 Thick
23 7090372 1 NUT, 1/4-20 Hex Center Lock, GR 5 or B
24 7091526 1 BOLT, 3/8-24 x 5/8” Shoulder
25 7091587 1 WASHER, .531 x 1.062 x .121 SAE Flat
26 7042650 1 WELDMENT, Idler Arm, 42” HOZ
27 7090122 2 WASHER, 3/8” SAE Flat
28 7090289 1 NUT, 3/8-24 Hex Center Lock GR 5 or B
29 7014241 1 WASHER, 1/4” Flat

tionItem Qt

Note

decals 24910, 46720 & 13010.

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

45

TP 400-5049-1-HZ-N

42" MOWER DECK ASSEMBLY (Part 3)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

46

SERIES 6

42" MOWER DECK ASSEMBLY (Part 3)

p

y

Part No Descri

43 7035835 4 POST, Anti Scalp 42” Deck
44 7091328 8 SCREW, 3/8-16 x 1-1/4”, Hex Head Cap, GR 5
45 7091619 8 NUT, 3/8-16 Hex Flange Lock Was 90613
46 7029265 4 BOLT, Gage Wheel, 3/8-16 x 3-3/8” Hex Head Shoulder for gage wheel
47 7091585 6 NUT, 3/8-16 Hex Center Lock, GR 5 or B
48 7029264 4 WHEEL, Gage
49 7022717 1 ROD, Deck Support
50 7017847 1 RING, .438 External Retaining
51 7075235 1 BELT, HA Sect., 94.5” nom. effective length
52 7028728 2 ADJUSTER, Chain (5/16-18 thread)
53 7028200 2 SWIVEL, Adjustment
54 7090122 5 WASHER, 3/8” SAE Flat replaces 91514, 91296
55 7091503 3 HAIR PIN, 3/32 x 1-1/2”
56 7024910 1 DECAL, 42” Deck see decal page
57 7035969 1 SPRING, Extension 1.03 Dia. X 6.8” long
58 7036561 1 BELT GUIDE, 38/42 Idler, HOZ
59 7012063 2 WASHER, .406 I. D. Cone
60 7075707 1 IDLER, Flat (4.00 O.D.)
61 7091553 2 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
62 7018574 1 IDLER, 4.12” Outside Diameter, Flat
63 7090799 2 BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR 5
64 7011791 2 RETAINER, 5/16” Bolt
65 7091315 2 WASHER, .32 x .58 x .08 Split Lock
66 7091537 2 WING LOCKNUT, 5/16-18
67 7091303 2 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
68 7051401 1 ASSEMBLY, Chute & Decal includes items 69 & 70
69 7051401 1 WELDMENT, Side Chute Was 40497
70 7013010 1 DECAL, Danger, Cut Finger see decal page
71 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
72 7023606 2 VINYL CAP, 1/4” I.D.
73 7046720 1 DECAL, Chute/Deflector see decal page

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

47

TP 400-5049-1-HZ-N

48" MOWER DECK ASSEMBLY (Part 1)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

48

SERIES 6

48" MOWER DECK ASSEMBLY (Part 1)

p

y

Part No Descri

1 7013847 3 RETAINER, 3/8” Bolt

2 7034321 1 STIFFENER, 48” Deck, HOZ

3 7044848 1 WELDMENT, 48” Deck

4 7047047 1 HANGER Rear R.H.

5 7047048 1 HANGER Rear L.H.

6 7047049 1 BRACKET, Pulley Mounting

7 7074230 1 BRACKET, Front Lift L.H.

8 7074231 1 BRACKET, Front Lift R.H.

9 7059240 1 WELDMENT, Front Lift, 48 Ref: Item 22 on 48” FRONT

10 7091619 6 NUT, 3/8-16 Hex Flange Lock
11 7058076 1 ASSEMBLY, Idler Arm- Lube Fitting (46706 Weldment & 13864

zerk)
12 7013864 1 LUBE FITTING, Straight (press-fit for .187 dia. Hole)
13 7074951 1 BRACKET, Hinge, 48” Deck
14 7071698 1 SPACER, Pivot Collar, 48 HOZ
15 7091888 1 BOLT, 3/8-16 x 4” Square Neck Carriage, GR 5
16 7090799 12 BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR 5
17 7091923 6 BOLT, 3/8-16 x 3/4” Short Neck Carriage, GR 5
18 7091601 19 NUT, 5/16-18 Hex Flange Lock, GR 5
19 7090122 2 WASHER, 3/8” SAE Flat replaces 91514, 91296
20 7091593 2 PIN, 3/8 Self Locking Cotter
21 7044801 4 WELDMENT, Caster Bracket
22 7091169 4 BOLT, 5/16-18X1-1/8” Short Neck Carriage, GR 5
23 7027168 3 SCREW, 5/16-18 x 1” Hex Head Cap, GR 5 Was 90636
24 7075587 1 BRACKET, Stationary Idler

tionItem Qt

Note

FRAME & COVER ASSEMBLY
page

includes 46706, Idler Arm
Weldment & one item 12

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

49

TP 400-5049-1-HZ-N

48" MOWER DECK ASSEMBLY (Part 2)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

50

SERIES 6

48" MOWER DECK ASSEMBLY (Part 2)

p

y

Part No Descri

26 7013010 1 DECAL, Danger, Cut Finger see decal page
27 7035813 1 SPRING, Torsion
28 7058508 1 SPRING, Extension, 48” HOZ
29 7029425 1 DISCHARGE CHUTE, Hi Impact Co-Polymer
30 7075092 1 V-BELT, HA Sect., 120.722” effective length
31 7043858 8 BUSHING, Flange, .64 x .75 x .5
32 7046301 4 SLEEVE, Caster Wheel
33 7046302 4 WELDMENT, Pivot Yoke, Caster
34 7046720 1 DECAL, Chute/Deflector see decal page
35 7047093 1 COVER, Belt, LH
36 7047094 1 COVER, Belt, RH
37 7090667 2 WASHER, 1/2” Flat
38 7058524 3 ASSEMBLY, 48” Spindle
39 7072319 1 PULLEY, 3-1/4 Dia. Flat Idler New Hampshire p/n FH-5220-14
40 -- 1 *ASSEMBLY, 48” Painted Mower Deck see previous two pages
41 7058086 2 LINK, Leveling (3/8-16 thread)
42 7058087 2 SWIVEL, Support (3/8-16 internal thread)
43 7072044 1 HINGE PIN
44 7091810 2 BOLT, 3/8-16 x 1-3/4” Short Neck Carriage, GR 5 Was 91158
45 7076436 8 SPACER, Blade
46 7073142 4 ROLLER, Low Density Polyethylene Was 79226
47 7091503 6 HAIR PIN, 3/32 x 1-1/2”
48 7091084 4 SCREW, 1/4-20 x 3/8” Hex Washer Self Tap Was 90302
49 7091585 3 NUT, 3/8-16 Hex Center Lock Was 90546
50 7090993 4 SCREW, 1/2-20 x 4-1/2” Hex Head Cap, GR 5
51 7090122 5 WASHER, 3/8” SAE Flat replaces 91514, 91296
52 7090266 4 NUT, 1/2-20 Hex Center Lock, GR 5 or B
53 7091628 4 WASHER, .64 x .99 x .05 Flat
54 7014341 2 RING, .392 External Retaining Waldes #5133-50
55 7018574 1 IDLER, 4.12” Outside Diameter, Flat
56 7024431 1 DECAL, 48” Deck see decal page
57 7034422 1 PULLEY, 5” x .375 Flat Idler (Belt Clutch)
58 7044813 3 PULLEY, Driven, 4.50” O.D.
59 7074467 3 NUT, 3/4-16 Hex Jam, GR 8
60 7014407 3 WASHER, Spindle also shown on 48” SPINDLE

tionItem Qt

Note

ASSEMBLY page

Footnotes:

*NOTE: Deck Ass'y 58522 consists of items 2-9, 11, 13, 14, 21, 24, 38, 58 & 60 assembled with appropriate fasteners.

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

51

TP 400-5049-1-HZ-N

42" SPINDLE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

52

SERIES 6

42" SPINDLE ASSEMBLY

p

y

Part No Descri

1 7051914 2 ASSEMBLY, Spindle, Brake Was 59723 (Includes 2 thru 7)
2 7012491 2 RING, 1-3/4” External Retaining Ring Truarc part no. N-5000-175
3 7013313 2 BALL BEARING, 3/4” I.D.
4 7051918 1 WELDMENT, Spindle Housing Was 47917
5 7032294 1 BLADE HOLDER (3/4-16 Internal Thread)
6 7014407 1 WASHER, Spindle
7 7027668 1 SHAFT, Blade Spindle (3.47” shanl length)
8 7010817 1 FITTING, Lube, Press-In (for .187 dia. Hole)

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

53

TP 400-5049-1-HZ-N

48" SPINDLE ASSEMBLY

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

54

SERIES 6

48" SPINDLE ASSEMBLY

p

y

Part No Descri

1 7058524 3 ASSEMBLY, 48” Spindle includes items 2 thru 10
2 7012491 2 RING, 1-3/4” External Retaining Ring Truarc part no. N-5000-175
3 7013313 2 BALL BEARING, 3/4” I.D.
4 7010817 1 FITTING, Lube, Press-In (for .187 dia. Hole)
5 7073405 1 SHAFT, Spindle (7.81” long)
6 7044798 1 WELDMENT, 48” Spindle
7 7014407 2 WASHER, Spindle
8 7016440 2 WASHER, .656 Belleville

9 7090658 1 NUT, 5/8-18 Hex Jam
10 7075588 1 BLADE, 16-1/2” Low Inertia
11 7027168 6 SCREW, 5/16-18 x 1” Hex Head Cap, GR 5 Was 90636 (not part of 58524

12 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070 (not part of 58524

tionItem Qt

Note

assembly)

assembly)

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

55

TP 400-5049-1-HZ-N

DECALS

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

56

SERIES 6

DECALS

p

y

Part No Descri

1 7075760 2 DECAL, SNAPPER

2 7034817 1 DECAL, SCRAMBLER

3 7075812 1 DECAL, Park Brake

4 7046426 1 DECAL, Deck Height

5 7013010 1 DECAL, Danger, Cut Finger

6 7075993 1 DECAL, Warning, Read Manuals & Instructions

7 7046457 1 DECAL, Deck Position

8 7078044 1 DECAL, Service Parts, HOZ Domestic

9 7078022 1 DECAL, OPEI Walk/Ride
10 7078049 1 DECAL, Throttle/Choke Control
11 7044767 2 DECAL, Hydro Reservoir
12 7071683 1 DECAL, Hydro Release
13 7029113 1 DECAL, Caution, Fuel (English)
14 7072952 1 DECAL, Ignition Switch, Twin Stick
15 7024910 1 DECAL, 42” Deck
16 7024431 1 DECAL, 48” Deck
17 7046720 1 DECAL, Chute/Deflector

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

57

TP 400-5049-1-HZ-N

ELECTRICAL COMPONENTS (Part 1)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

58

SERIES 6

ELECTRICAL COMPONENTS (Part 1)

p

y

Part No Descri

1A 7073426 1 WIRING HARNESS, 18 HP Briggs Intek- Twin Stick
1B 7075074 1 WIRING HARNESS, 20 HP Briggs V-Twin- Twin Stick

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

59

TP 400-5049-1-HZ-N

ELECTRICAL COMPONENTS (Part 2)

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

60

SERIES 6

ELECTRICAL COMPONENTS (Part 2)

p

y

Part No Descri

1 7090411 2 SCREW, #10-24 x 1/2” Hex Head Cap

2 7012688 2 NUT, #10-24 Hex Twin “Whiz” Lock

3 7035926 1 WIRE HARNESS, Warner Clutch

4 7016835 1 WIRE, Positive, 13” long

5 7042956 1 WIRE, Negative, 14” long

6 7071694 2 COVER, Battery Cable

7 7090977 2 NUT, 1/4-20 Hex Jam, GR 5 or B

8 7022886 1 SWITCH, Seat (NO/NC) Snap-In

9 7075884 1 SWITCH, PTO E.C. (Delta Part No. 6201-219)
10 7023355 3 SWITCH, Park Brake (NC/NO)
11 7090913 3 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
12 7029130 1 BATTERY, 12V, 3 Amp, 190 Cold Cranking Amp includes drain tube, p/n 91855
13 7026343 1 SWITCH, Ignition (After-fire Solenoid)
14 7035661 1 SPACER, PTO Switch
15 7023506 1 BEZEL
16 7075622 1 SOLENOID - Super Trombetta- 2 Terminal
17 7090071 2 SCREW, 1/4-20 x 1/2” Hex Head Cap, GR 5
18 7091584 3 NUT, 1/4-20 Hex Flange Lock
19 7090053 3 WASHER, 1/4” Internal Tooth Lock Was 91314
20 7028570 1 RELAY, OPC, Electric Clutch

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

61

TP 400-5049-1-HZ-N

WIRING SCHEMATIC

Manual No. 7006181 SCRAMBLER ZERO-TURN
TP 400-5049-1-HZ-N

62

SERIES 6

WIRING SCHEMATIC

p

y

Part No Descri

-- -- 1 Wiring schematic includes harness #'s 73426 & or 75074

tionItem Qt

Note

Footnotes:

Manual No. 7006181SCRAMBLER ZERO-TURN

SERIES 6

63

TP 400-5049-1-HZ-N

Parts Manual fo

r

N

T

SCRAMBLER ZERO-TUR
42" & 48" HYDRO DRIVE SZ
SERIES 6

RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS

COPYRIGHT ©2005
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.

IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS

WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE

AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE

SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.

McDonough, GA, 30253 U.S.A.

Revision 1,

7/28/2005

Manual No. 700618 1

TP 400-5049-1-HZ-N