Snapper SST-BC User Manual

Specifications and Main Features

  • Model: Brush Cutter (Snapper SST-BC)
  • Engine: 34cc Briggs & Stratton 4 cycle
  • Shaft Type: Straight
  • Shaft Length: 62.5 inches.
  • Cutting Width: nylon line – 17 inches, blade – 8 inches
  • Cutter Diameter: .095 inches / 2.4 mm
  • Weight: 13.7lbs (J Handle Bar Unit 6.264kg, Bike Handle Bar 6.292kg)
  • Head Type: Bump feed with inclusion of 8 inches diameter blade
  • Starting Type: Easy start 4 cycle
  • Type of Handle: J Type (SST-BC) and optional Bike Handle
  • Clutch: Yes
  • Shoulder Harness: Yes
  • Warranty: 2 years for Consumer, 90 days for Commercials
  • Volume of Fuel Reservoir: 296cm3
  • Maximum Engine Performance: 0.746 kw
  • Maximum Operational Rotational Speed of the Spindle: 6467RPM
  • Maximum Engine Speed corresponding to Maximum Spindle Speed: 8600RPM
  • Low Idling Engine Speed: 3600RPM
  • Fuel Burn: 0.399 kg/h
  • Specific Fuel Consumption: 542 g/kWh
  • Vibration Levels:

– Wide Open Throttle – Left Hand=3.20 m/s², Right Hand=2.76 m/s²

– Idle – Left Hand=2.14 m/s², Right Hand=2.28 m/s²

  • Sound Pressure Levels: Operator Ear Lp dB(A)= 91.44

——

Frequently Asked Questions

A1: The Snapper SST-BC Brush Cutter is powered by a 34cc 4-cycle Briggs & Stratton engine which gives it more pace.

Q2: Could you provide me with the measurements of the SST-BC Brush Cutter?

A2: The unit weight is 13.7 lbs (6.264 kg for J Handle Bar Unit; 6.292 kg for Bike Handle Bar Unit).

Q3: How wide can the brush cutter be during the trimming session?

A3: The brush cutter possesses a trimming range of 17 inches with a nylon line and 8 inches with a blade.

Q4: Will I be provided with a shoulder harness along with the device?

A4: Yes, a shoulder harness is included.

Yes, a shoulder harness is included.

Q5: How long can I use the Snapper SST-BC before I have to get it checked or serviced?

A5: The warranty is 2 years while used in the consumer sector and 90 days while used commercially.

Q6: Is there something specific that I should do if I face issues starting the engine?

A6: Improper fuel or plugged fuel filters or carburetor(idle speed outside of limits) may be seen as some reasons and it is suggested that you take these points into consideration.

Q7: What can I do to change the trimming line?

A7: Use .095 inch (2.4 mm) diameter replacement line as instructed in the manual. Moreover, read about spool removal and installation of line for a better experience.

Q8: What safety measures do you recommend to your users while handling a brush cutter?

A8: As a coverall, always put on all necessary protective gear, keep bystanders out of the brush cutter operation zone and do not use the cutter in any indoor area or a confined setting.

Q9: Is it permissible to install aftermarket blades on the unit SST-BC Brush Cutter?

A9: Certainly not, it is a very high safety risk to apply any aftermarket head or attachment or accessory onto this device. Only installation made parts by Snapper for this apparatus should be utilized.

Q10: Whom should I contact for seeking customer support in relation to Snapper SST-BC?

A10: In case of any queries regarding the customer support reach out to the Snapper Customer Relations via 1-800-935-2967.

User Manual

Page 1
Snapper SST-BC User Manual
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Loading...