Snapper SPLH141KW, SPLH151KH, SPA611, SPLH171KW, SPLH141KH User Manual

Parts Manual fo

r

S

W

E

W

W

E

E

PRO HYDRO

MID-SIZE WALK BEHIND MOWER

SERIES 1 & 2

POWER UNIT

MODELS

SPLH141KH SP360

SPLH141K

SPLH141KW

SPLH151KH SPA360
SPLH152K
SPLH171K

SPLH221KH
SPLH231KH

MOWER
MODELS

SP480
SP520

SPA361
SPA480
SPA481
SPA520
SPA521
SPA610
SPA611

COPYRIGHT ©2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.

Revision 4,

McDonough, GA, 30253 U.S.A.

11/7/2006

Manual No. 7006928

TP 400-5023-4-CW-N

s

PAGE GROUP

4

8
10
12
14
16
18
22
24
26
28
30
32
34
36
40
42
46
48
50
52
54
56
58
60
62
64
66

LOOP HANDLE & CONTROL ASSEMBLIES
TRACKING CONTROL ASSEMBLY
OIL TANK ASSEMBLY (Model SPLH231KHE)
OIL TANK ASSEMBLY (All Except SPLH231KHE)
TANK BRACKET ASSEMBLY
FUEL TANK ASSEMBLY
REAR DECK ASSEMBLY
PUMP AND SHELF ASSEMBLIES
HOSE ASSEMBLY
POWER UNIT IDLER ASSEMBLY
TRACTION, REAR WHEEL ASSEMBLY
ENGINE GROUP
CASTER, WHEEL & TIRE ASSEMBLY
36" MOWER DECK ASSEMBLY (Fixed Height)
36" MOWER DECK ASSEMBLY (Adjustable Height)
48" & 52" MOWER DECK ASSEMBLY (Fixed Height)
48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.1
48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.2
36" DECK IDLER ASSEMBLY
48" & 61" DECK IDLER ASSEMBLY
52" DECK IDLER ASSEMBLY
CUTTER HOUSING ASSEMBLY
DECALS - Left & Right Panels
DECALS - Instructions, Caution, Warning, Danger
ELECTRICAL WIRING (Manual Start)
ELECTRICAL WIRING- LOOP HANDLE (Electric Start)
WIRING SCHEMATIC (Manual Start)
WIRING SCHEMATIC (Electric Start)

Table Of Content

SERIES 1 & 2

Manual No. 700692 8PRO HYDRO

3

TP 400-5023-4-CW-N

LOOP HANDLE & CONTROL ASSEMBLIES

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

4

SERIES 1 & 2

LOOP HANDLE & CONTROL ASSEMBLIES

p

y

Part No Descri

1 7011138 1 IGNITION KEY, Pair
2 7012685 1 NUT, 5/8-32 Hex (Ignition Switch)
3 7012686 1 NUT, 1/2-27 Hex (Special)
4 7014341 2 RETAINING RING Truarc #5133-50
5 7017817 1 SWITCH, Ignition, 2-Pole, Recoil Start (except Kohler 23HP)
5 7027698 1 SWITCH, Ignition used on Kohler 23HP
6 7022166 1 ROD, Pivot, 1/2” Dia. x 18.542 w/2 retaining Ring Grooves
7 7027141 2 SWIVEL
8 7027225 1 SWITCH, OPC, Single Pole (NC) used on Loop Handle except

8 7023355 1 SWITCH, OPC, (NO/NC) used on Kohler 18HP

9 7028856 2 CONTROL ROD (Traction)
10 7028857 4 BEARING, Nyliner
11 7074648 1 ROD, Operator Presence Control
12 7029139 1 SPRING, OPC- Loop Handle
13 7029715 1 SWITCH, Toggle
14 7034827 1 PANEL, Left
15 7034828 1 PANEL, Right
16 7041748 1 BAIL, Operator Presence Control (Weldment)
17 7091303 4 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
18 7090977 2 NUT, 1/4-20 Hex Jam
19 7091222 2 BOLT, 1/4-20 x 1-3/4” Hex Head Cap, GR 5
20 7091030 2 BUSHING, 1/2” Machine
21 7091122 8 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
22 7091297 2 NUT, 5/16-24 Hex, GR 5
23 7091299 4 NUT, 3/8-16 Hex Nyloc
24 7077873 2 SCREW, #12-14 x 1/2” Hex Flange Self-Tap
25 7091594 2 COTTER PIN, 1/2” Self-Locking
26 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
27 7034820 1 WELDMENT, Traction Lever, RH
28 7034821 1 WELDMENT, Traction Lever, LH
29 7043869 1 HANDLE, Loop (Weldment)
30 7029100 1 THROTTLE CONTROL, 40.50/1.46 used on Kawasaki 14HP &

30 7072597 1 THROTTLE CONTROL, 51.50/0.90 used on Kawasaki 17HP
30 7036431 1 THROTTLE CONTROL, 48.50/0.90 used on Kohler 23HP
31 7012080 4 CABLE TIE, 7”
32 7073118 1 * WIRE HARNESS not shown; for all models except

32 7073117 1 * WIRE HARNESS not shown; used on Kohler 23HP

tionItem Qt

Note

Kohler 23HP

Kohler 15HP

for Kohler 23HP

Footnotes:

SERIES 1 & 2

NOTE: * See Electrical Wiring pages for Illustration.

Manual No. 700692 8PRO HYDRO

5

TP 400-5023-4-CW-N

LOOP HANDLE & CONTROL ASSEMBLIES

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

6

SERIES 1 & 2

LOOP HANDLE & CONTROL ASSEMBLIES

p

y

Part No Descri

33 7041692 1 * HARNESS, Wiring Pigtail not shown; used on

33 7027226 1 * HARNESS, Wiring Pigtail not shown; used on

33 7046901 1 * HARNESS, Regulator not shown, used on

34 7073141 1 SWITCH, Interlock, Sealed (NC)
34 7073140 1 SWITCH, Interlock, Sealed (NO/NC) used on Electric Start only
35 7073139 1 BRACKET, Interlock Switch
36 7090376 2 NUT, #10-32 Hex Nyloc
37 7091240 2 SCREW, #10-32 x 5/8” Hex Machine

tionItem Qt

Note

SPLH171KW only

SPLH141KW only

SPLH141KWE only

Footnotes:

SERIES 1 & 2

NOTE: * See Electrical Wiring pages for Illustration.

Manual No. 700692 8PRO HYDRO

7

TP 400-5023-4-CW-N

TRACKING CONTROL ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

8

SERIES 1 & 2

TRACKING CONTROL ASSEMBLY

p

y

Part No Descri

1 7011879 1 GRIP, Vinyl

2 7013550 1 PIN, 3/16 x 1” Roll

3 7011121 2 WASHER, 5/8” I.D., 1-1/4” O.D. Belleville

4 7027125 1 SPRING, Compression

5 7027168 2 SCREW, 5/16-18 X 1” Hex Head Cap, GR 5

6 7027169 1 SCREW, 3/8-16 x 5” Hex Head Cap, GR 5

7 7028859 1 LEVER

8 7028860 2 BUSHING

9 7029040 4 WASHER, Slipper
10 7034803 2 PIN, Shoulder
11 7034830 1 CAM, Track
12 7034877 2 PLATE, Speed, Accutrack
13 7091299 1 NUT, 3/8-16 Hex Nyloc
14 7091706 2 NUT, 5/16-18 Hex Top Lock, GR B
15 7019376 1 HANDLE, Shift Lever
16 7059115 1 WELDMENT, Neutral Latch
17 7041772 1 TRACK, Welded
18 7091300 3 WASHER, .44 x 1.0 x .08 Flat
19 7091130 1 WASHER, .33 x .88 x .09 Flat

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

Manual No. 700692 8PRO HYDRO

9

TP 400-5023-4-CW-N

OIL TANK ASSEMBLY (Model SPLH231KHE)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

10

SERIES 1 & 2

OIL TANK ASSEMBLY (Model SPLH231KHE)

p

y

Part No Descri

1 7026945 1 CAP, Hydraulic

2 7028972 1 TANK, Reservoir

3 7029039 1 PLUG, 1/4 NPTM Pipe

4 7029159 2 FITTING, 45 Degree 1/4 FPT Elbow

5 7027115 1 FITTING, 90 Degree

6 7027104 2 FITTING, Straight 1/4

7 7027105 2 FITTING, External 45 Degree w/37 Degree Flare

8 7028912 2 HOSE, 10-1/2” Long (7/16-20 Female Thread)

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

11

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

OIL TANK ASSEMBLY (All Except SPLH231KHE)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

12

SERIES 1 & 2

OIL TANK ASSEMBLY (All Except SPLH231KHE)

p

y

Part No Descri

1 7058610 1 OIL TANK (Includes Item 2)

2 7035512 1 CAP, Oil Tank, Vented

3 7016130 1 CLAMP, 13/16” Hose

4 7072897 1 HOSE, 1/2 x 19-1/2” Supply (3/4-16 Fitting on One End)

5 7072898 1 HOSE, 1/2 x 24-1/2” Return (7/16-20 Fitting on One End)

6 7072910 1 HOSE, Return, 10-1/2” (7/16-20 Fitting on One End)

7 7072899 1 COVER, Oil Tank Bracket

8 7072895 1 BRACKET, Reservoir, Hydro

9 7072896 1 RETAINING ROD, Reservoir (1/4-20 threads)
10 7091705 1 NUT, 1/4-20 Hex Top Lock, GR B
11 7015761 2 SHOULDER BOLT, 5/16-18
12 7011079 2 WASHER, 3/8” Curved
13 7091298 6 NUT, 5/16-18 Hex Nyloc
14 7091495 2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
15 7091294 2 SHOULDER BOLT, 3/8-16 x 2-7/16”
16 7023295 2 U-NUT 1/4-20
17 7091303 4 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
18 7029900 2 CLAMP, Fuel Hose

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

13

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

TANK BRACKET ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

14

SERIES 1 & 2

TANK BRACKET ASSEMBLY

p

y

Part No Descri

1 7042584 1 WELDMENT, Tank Bracket- Hydro

2 7073073 1 BRACKET, Regulator

3 7034837 1 * STRAP, Battery Clamp

4 7091298 2 NUT, 5/16-18 Hex Nyloc

5 7028983 1 REGULATOR/RECTIFIER (Kawaaski p/n 21066-2071) used on Kawasaki Manual Start

5 7047210 1 REGULATOR (Kawaaski p/n 21066-2070) used on Kawasaki Electric Start

6 7027230 4 SCREW, 1/4-20 x 1” Hex Head Cap, GR 5

7 7091705 2 NUT, 1/4-20 Hex Top Lock, GR B

8 7024185 1 CABLE, Choke (Incl. hardware) used on Kohler 23 HP

9 7027168 2 SCREW, 5/16-18 X 1” Hex Head Cap, GR 5
10 7091304 6 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
11 7091299 6 NUT, 3/8-16 Hex Nyloc
12 7091304 1 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
13 7091704 2 NUT, 3/8-16 Hex Top Lock, GR B
14 7041765 1 * TRAY, Battery
15 7034851 1 * BRACE, Battery
16 7018604 1 * SOLENOID, 12 Volt
17 7091495 2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
18 7091705 2 NUT, 1/4-20 Hex Top Lock, GR B
19 7091314 2 * WASHER, 1/4” Internal Tooth lock
20 7091576 2 * NUT, 1/4-20 Hex, GR 5 or B
21 7028913 2 * J-BOLT, 1/4-20 thread
22 7090311 2 * NUT, 1/4-20 Wing or 7091568
23 7060974 1 * KIT, Battery

tionItem Qt

Note

only

only

Footnotes:

SERIES 1 & 2

NOTE: * Items marked with an * are used on Electric Start Models only.

15

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

FUEL TANK ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

16

SERIES 1 & 2

FUEL TANK ASSEMBLY

p

y

Part No Descri

1 7028903 1 CAP, Fuel Tank

2 7044639 1 FUEL TANK includes item 1

3 7034923 2 STRAP, Tank

4 7091207 2 SCREW, #10-24 x 2-1/2” Pan Head Machine

5 7091290 2 NUT, #10-24 Hex Nyloc

6 7029900 6 CLAMP, Fuel Hose replaces 7012222 clamp

7 7016325 1 VALVE, Fuel

8 7014359 1 FILTER, In-Line used on Kawasaki models only

9 7032956 1 * LINE, Fuel (1/4” I.D. x 10” Long)
10 7024055 1 * HOSE, Fuel (1/4” I.D. x 6-1/2” Long)
11 7076272 1 * HOSE, Fuel (1/4” I. D. x “ 8-1/2 Long) not shown
12 7073240 1 * HOSE, Fuel (1/4” I. D. x 5” Long)
13 7077351 1 * HOSE, Fuel (1/4” I.D. x 3-1/2” Long) not shown

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

NOTE: * When ordering hoses, measure length of hose to be replaced or distance between connections.

Manual No. 700692 8PRO HYDRO

17

TP 400-5023-4-CW-N

REAR DECK ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

18

SERIES 1 & 2

REAR DECK ASSEMBLY

p

y

Part No Descri

1A 7091807 1 WASHER, .468 x 1.38 x .25 Flat
1B 7075082 1 SPACER, Clutch

2 7091301 1 WASHER, 7/16” Split Lock replaces 7090247

3 7026978 1 BRACKET, Capacitor Kawasaki Engines only

4 7028680 1 SCREW, M10-1.5 x 65mm Hex Head Cap used on Kawasaki 14HP

4 7027266 1 BOLT, 7/16-20 x 3” Hex Head Cap, GR 5 used on Kawasaki 17HP and

4 7091703 1 SCREW, 7/16-20 x 2-1/2” Hex Head Cap, GR 5

5 7012830 2 KEY, 3/16” Square x 3/4”

6 7015861 1 CLIP, Harness (for battery drain hose) used on SPLH141KWE only

7 7034802 2 BRACKET, Wheel

8 7034829 1 BRACKET, Clutch

9 7091303 1 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
10 7091527 3 SCREW, 5/16-18 x 1-1/4” Hex Head Cap, GR 5
11 7091304 12 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
12 7091706 5 NUT, 5/16-18 Hex Top Lock, GR B
13 7091704 14 NUT, 3/8-16 Hex Top Lock, GR B
14 7017063 1 CLUTCH, Electric (Warner)

14A 7072400 1 CLUTCH, Electric (Ogura) On Models SPLH231KHE,

14B 7075672 1 CLUTCH, Electric (Ogura model GT2.5 SN01) requires use of 7017033,

15 7044679 1 DECK, Rear (Weldment)
16 7027194 2 PACK NUT, 3/4-28 UNEF-2A Thread
17 7091318 3 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
18 7027235 1 CAPACITOR, Kawasaki Engine Kawasaki p/n 21013-2064
19 7029615 1 V-BELT, HA4950 Engine/Hydro
20 7027128 2 WHEEL MOTOR w/Pack Nut includes item 16
21 7029704 1 BUMPER, Electric Clutch
22 7034448 1 WASHER, Rectangular Steel electric clutch bumper support
23 7027132 1 PULLEY, 4”, Engine/Hydro

24A 7044751 1 KEY, 1/4” Square w/Bevel
24B 7010210 1 KEY, 1/4” Square x 2” used on SPLH231KHE only

25 7035710 1 * V-BELT, Sect HB, Nom. Eff. Length: 84.80” (Engine/Deck belt) used on 36” Deck
25 7029262 1 * V-BELT, Sect HB, Nom. Eff. Length: 66.00” (Primary

Engine/Deck belt)
25 7042813 1 * V-BELT, Sect HB, Nom. Eff. Length: 67.80” (Engine/Deck belt) used on 52” Deck
25 7042735 1 * V-BELT, Sect HB, Nom. Eff. Length: 74.00” (Primary

Engine/Deck belt)
26 7015861 1 CLIP, Harness used on SPLH231KHE

27A 7074867 1 KEY, 1/4” Square x 2-1/2”
27B 7017033 1 KEY, 1/4” Square x 2-1/4”

tionItem Qt

Note

Kohler 15HP

SPLH152KW & SPLH172KW

7075082 & 7075084

used on 48” Deck

used on 61” Deck

Footnotes:

SERIES 1 & 2

NOTE: * Part numbers are printed on belts.

19

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

REAR DECK ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

20

SERIES 1 & 2

REAR DECK ASSEMBLY

p

y

Part No Descri

28A 7027206 1 BUSHING
28B 7075084 3 SPACER,Clutch, Ogura

29 7016561 1 BUSHING, 1” x 14 Ga Machine

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

NOTE: * Part numbers are printed on belts.

21

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

PUMP AND SHELF ASSEMBLIES

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

22

SERIES 1 & 2

PUMP AND SHELF ASSEMBLIES

p

y

Part No Descri

1 7091528 6 WASHER, 3/8” I.D. x 7/8” O.D. x 1/16” Flat
2 7091318 2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
3 7029000 2 SPACER, Blade Hub
4 7028862 2 ECCENTRIC
5 7028863 2 ARM, Pump
6 7028907 4 BUSHING, Spring
7 7027127 2 HYDRAULIC PUMP
8 7027131 2 PULLEY, 5.5 w/Set Screws Includes two 1/4-20 set screws

9 7091627 2 WASHER, 1/4” Flat
10 7027223 2 WASHER, 1/4” I.D. Split Lock
11 7072893 2 SHIFT ARM, Pump
12 7091835 2 SCREW, M6 1.0 x 12mm Hex Head Cap
13 7091705 4 NUT, 1/4-20 Hex Top Lock, GR B
14 7091575 2 NUT, 5/16-18 Hex Center Lock, GR 5 or B
15 7091721 2 ROLL PIN, 5mm x 25mm
16 7091527 2 SCREW, 5/16-18 x 1-1/4” Hex Head Cap, GR 5
17 7090825 4 SCREW, 1/4-20 x 1-1/4, Hex Head Cap, GR 5
18 7027199 2 KEY, M5 x M20
19 7027181 4 BOLT, 3/8-16 x 1-1/4” Short Neck Carriage, GR 5
20 7072579 2 SPRING, Hydro
21 7077680 2 SETSCREW- 1/4-20 x 3/8” Socket Head Knurled Cup Point
22 7091315 2 WASHER, .32 x .58 x .08 Split Lock
23 7027139 2 ROD END, Pump Control Linkage (5/16-24 thread)
24 7091704 4 NUT, 3/8-16 Hex Top Lock, GR B

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

23

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

HOSE ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

24

SERIES 1 & 2

HOSE ASSEMBLY

p

y

Part No Descri

1 7027106 1 FITTING, External 90 Degree w/37 Degree Flare 1/2-14 & 3/4-16 Threads
2A 7027118 1 HOSE, 1/2 x 16-1/2” Long (3/4-16 Female Thread, Both Ends) used on SPLH231KHE only
2B 7072898 1 HOSE, 1/2 x 16-1/2” Long (7/16-20 Thread) used on All Other models

3 7027165 1 MOUNT, Oil Filter

4 7027200 1 FITTING, 7/16-20 Straight (Right Side Pump Only)

5 7027108 1 FITTING, 7/16-20 Straight w/”O”-Ring (Right Side Pump Only)

6 7028912 2 HOSE, 10-1/2” Long (7/16-20 Female Thread)

7 7027111 2 FITTING, 90 Degree- “O”-Ring Boss
8A 7027120 2 HOSE, Pump/Motor High Pressure, 24-1/2” (Right Side Pump Only)
8B 7029058 2 HOSE, Pump/Motor, High Pressure 21-1/2” (Left Side Pump Only)

9 7027168 3 SCREW, 5/16-18 X 1” Hex Head Cap, GR 5
10 7027221 1 BOLT, 3/8-16 x 3-1/2” Hex Head, GR 5
11 7091706 3 NUT, 5/16-18 Hex Top Lock, GR B
12 7091299 2 NUT, 3/8-16 Hex Nyloc
13 7027164 1 OIL FILTER

14A 7027112 2 FITTING, 90 Degree w/”O”-Ring Boss (Right Side Pump Only)
14B 7027113 2 FITTING, 45 Degree w/SAE “0”-Ring Boss (Left Side Pump Only)

15 7027105 2 FITTING, External 45 Degree w/37 Degree Flare

16A 7027109 1 FITTING, 90 Degree w/37 Degree Swivel (Right Side Pump Only)
16B 7027110 1 FITTING, 90 Degree w/”O”-Ring Boss (Left Side Pump Only)

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

25

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

POWER UNIT IDLER ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

26

SERIES 1 & 2

POWER UNIT IDLER ASSEMBLY

p

y

Part No Descri

1 7091704 1 NUT, 3/8-16 Hex Top Lock, GR B

2 7076998 1 GREASE FITTING, 1/4-28 Straight

3 7026886 1 IDLER ARM Weldment

4 7091300 3 WASHER, .44 x 1.0 x .08 Flat

5 7027129 1 PULLEY, Idler

6 7027220 1 BOLT, 3/8-16 x 3-1/4” Hex Head, GR 5

7 7016173 1 SPACER, Pivot

8 7027221 1 BOLT, 3/8-16 x 3-1/2” Hex Head, GR 5

9 7027124 1 SPRING, Idler Tension (extension)
10 7016561 1 BUSHING, 1” x 14 Ga Machine
11 7091299 2 NUT, 3/8-16 Hex Nyloc

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

27

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

TRACTION, REAR WHEEL ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

28

SERIES 1 & 2

TRACTION, REAR WHEEL ASSEMBLY

p

y

Part No Descri

1 7058880 2 ASSEMBLY, Rear Tire & Rim Includes item 2, 3A & 6A

1 7058425 2 ASSEMBLY, Rear Tire & Rim, Turf Saver, Gray Includes item 2, 3B & 6B

2 7073526 1 TIRE, 16 x 6.50-8, 4 Ply (Carlisle “Turf Chief”)

3 7027189 1 RIM (White)

3 7075729 1 RIM (Gray)

4 7012234 1 AIR VALVE, Snap-In Goodyear p/n TR-412

5 7027192 8 LUG-NUT, 1/2-20 Tapered Seat

6 7027191 2 WHEEL HUB, w/4 threaded studs

6 7075303 2 WHEEL HUB, w/4 threaded studs

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

29

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

ENGINE GROUP

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

30

SERIES 1 & 2

ENGINE GROUP

p

y

Part No Descri

1 1 * ENGINE, 14HP Kawasaki Spec. No. FC420V-DS09

1 1 * ENGINE, 14HP Kohler Model CV14T; Spec. No. PS-

1 1 * ENGINE, 14HP Kawasaki Electric Start Spec. No. FC420V-HS01

1 1 * ENGINE, 14HP Kawasaki Electric Start Spec. No. FC420V-HS09

1 1 * ENGINE, 15HP Kohler Spec. No. PS-41579

1 1 * ENGINE, 15HP Kawasaki Spec. No. FH430V-AS02

1 1 * ENGINE, 17HP Kawasaki Model No. FH500V; Spec. No.

1 1 * ENGINE, 17HP Kawasaki Spec. No. FH500V-AS02

1 1 * ENGINE, 22HP Kohler Model No. CV22S; Spec. No.

1 1 * ENGINE, 23HP Kohler Model No. CV23S; Spec. No.

2 7028959 1 MUFFLER, V-Twin Kohler not shown; used on

3 7027972 1 ASSEMBLY, Oil Valve

4 7017783 1 PIPE, Oil used on SPLH231KHE only

5 7017814 1 CAP, Oil Drain used on SPLH231KHE only

6 7028958 1 HEAT SHIELD used on SPLH231KHE only
7A 7077692 4 SCREW, M8 x 1.25 x 25.0 Hex Head Cap, Class 8.8 used on Kawasaki & Kohler

7B 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5 used on Kawasaki 17HP &

8 7091649 4 SCREW, #8-18 x 9/16” Hex Washer Self-Tap used on SPLH231KHE only

9 7043813 1 ASSY, Clamp (Incl. Clamp, U-Bolt, 2 Split Lock Washers & 2 Hex

Nuts)
10 7043814 1 ELBOW, Exhaust used on SPLH231KHE only
11 7091315 4 WASHER, .32 x .58 x .08 Split Lock
12 7074953 1 ADAPTER, Oil Drain Kawasaki #59071-7004 (not

13 7074954 1 O-RING not shown

tionItem Qt

Note

1464; (shown)

AS17

PS-75512

PS-75539

SPLH231KHE only

15HP models

Kohler 23HP models

used on SPLH231KHE only

shown)

Footnotes:

SERIES 1 & 2

NOTE: * Purchase engine & engine parts, other than those listed, from engine manufacturer dealer.

Manual No. 700692 8PRO HYDRO

31

TP 400-5023-4-CW-N

CASTER, WHEEL & TIRE ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

32

SERIES 1 & 2

CASTER, WHEEL & TIRE ASSEMBLY

p

y

Part No Descri

1 7029869 2 * ASSEMBLY, Wheel & Tire (White Rim); incl. items 2 thru 5
1 7057711 2 * ASSEMBLY, Wheel & Tire (Gray Rim); incl. items 2 thru 5 or 7058167
2 7022394 2 RETAINER, Flanged
3 7029870 1 TIRE, 9 x 3.50-4
4 7029871 1 RIM, One-Piece Steel (White) includes Items 2 & 5
4 7057737 1 RIM, One-Piece Steel (Gray) includes Items 2 & 5
5 7022395 2 BEARING, Roller
6 7022151 2 SLEEVE, Axle
7 7091922 2 NUT, 1/2-13 Hex Nyloc
8 7091326 2 BOLT, 1/2-13 x 5-1/2” Hex Head Cap, GR 5

9 7042780 2 WELDMENT, Yoke Caster
10 7017711 2 LYNCH PIN, 7/16” Heavy Duty
11 7019152 8 SPACER
12 7021960 2 SPACER, PM
13 7023747 2 BUSHING, 1”
14 7046626 4 BUSHING, Caster
15 7076998 2 LUBE FITTING, 1/4-28 Straight

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

NOTE: * Also includes an air valve (7012234) and a 45 degree grease fitting (7046430).

33

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

36" MOWER DECK ASSEMBLY (Fixed Height)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

34

SERIES 1 & 2

36" MOWER DECK ASSEMBLY (Fixed Height)

p

y

Part No Descri

1 7012709 1 RING, 1” External Retaining

2 7013010 1 DECAL, Warning (CPSC Cut Finger)

3 7073647 1 DECAL, Danger, Keep Hands and Feet Away

4 7023735 3 KNOB, Hood (5/16-18 thread)

5 7024156 1 DECAL, Caution- Operator Instruction

6 7027950 1 SPRING, Chute

7 7035710 1 * V-BELT, 36” Deck Drive (Nom. Effective Length: 84.80”)

8 7029277 1 HINGE PIN, Chute

9 7029278 1 SPRING, Idler
10 7076940 3 SCREW, 5/16-18 x 4-1/2” Hex Head Cap, GR 5
11 7091313 1 COTTER PIN, 3/32 x 1”
12 7046580 1 DECAL, SNAPPER Pro w/Trademark
13 7058871 1 DEFLECTOR, 36” ANSI Compliant (Weldment)
14 7034963 1 COVER, 36”
15 7041295 1 PIVOT, Idler Arm (Weldment)
16 7054018 1 ASSEMBLY, Idler Arm, 36”
17 7057736 2 ASSEMBLY, Caster Red w/Gray Wheel
18 7054021 1 ASSEMBLY, 36” Deck, Fixed Height Deck weldment (7044665) plus

19 7076998 2 LUBE FITTING, 1/4-28 Straight
20 7091299 5 NUT, 3/8-16 Hex Nyloc
21 7091304 3 BOLT, 3/8-16 x 1” Hex Head Cap, GR 5
22 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR5
23 7044626 4 BUSHING, Caster
24 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR 5
25 7091528 9 WASHER, 3/8” I.D. Flat
26 7021128 6 SPACER
27 7054011 2 ASSEMBLY, Spindle see Cutter Housing Assembly

tionItem Qt

Note

4 bushings (7023556)

page

Footnotes:

SERIES 1 & 2

NOTE: * Part numbers are printed on belts.

35

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

36" MOWER DECK ASSEMBLY (Adjustable Height)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

36

SERIES 1 & 2

36" MOWER DECK ASSEMBLY (Adjustable Height)

p

y

Part No Descri

1 7012709 1 RING, 1” External Retaining

2 7013010 1 DECAL, Warning (CPSC Cut Finger)

3 7021128 6 SPACER

4 7021960 2 SPACER, Powdered Metal

5 7091528 9 WASHER, 3/8” I.D. x 7/8” O.D. x 1/16” Flat

6 7073647 1 DECAL, Danger Guard/Catcher

7 7046626 4 BUSHING, Caster

8 7023735 3 KNOB, Hood (5/16-18 thread)

9 7023747 2 BUSHING, 1”
10 7024156 1 DECAL, Caution- Operator Instruction
11 7027950 1 SPRING, Chute
12 7035710 1 V-BELT, 36” Deck Drive (Nom. Effective Length: 84.80”)
13 7029258 16 BUSHING, Suspension
14 7029259 2 STUD, Lift, 1/2-13 Thread, Both Ends
15 7046214 2 LIFT WASHER (Weldment)
16 7029263 8 SLEEVE, Suspension
17 7029277 1 HINGE PIN, Chute
18 7029278 1 SPRING, Idler
19 7029295 2 DECAL, Height of Cut
20 7076940 3 SCREW, 5/16-18 x 4-1/2” Hex Head Cap, GR 5
21 7029355 8 BOLT, 1/2-13 x 3-3/4” Hex Head, GR 5
22 7091587 8 WASHER, 1/2” Flat
23 7046580 1 DECAL, SNAPPER Pro w/Trademark
24 7090613 2 NUT, 3/8-16 Hex Flange Lock
25 7058871 1 DEFLECTOR, 36” ANSI Compliant (Weldment)
26 7034964 4 ARM, Suspension, 12” Long
27 7034980 1 COVER, 36”
28 7035279 2 BRACKET, Height-of-Cut
29 7041295 1 PIVOT, Idler Arm (Weldment)
30 7042473 1 FRAME, 36” Adjustable (Weldment)
31 7035756 2 PLATE, Ballasat
32 7054012 2 ASSEMBLY, Crank (Includes Crank, 7042477,

33 7054018 1 ASSEMBLY, Idler Arm, 36” see 36” Deck Idler Assembly

34 7044664 1 WELDMENT, Deck, Adjustable Height (Red)
35 7076998 2 LUBE FITTING, 1/4-28 Straight
36 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR 5
37 7091819 2 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap

tionItem Qt

Note

Handle 7029380 & Roll Pin

7013877)

page

Footnotes:

SERIES 1 & 2

37

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

36" MOWER DECK ASSEMBLY (Adjustable Height)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

38

SERIES 1 & 2

36" MOWER DECK ASSEMBLY (Adjustable Height)

p

y

Part No Descri

38 7091299 20 NUT, 3/8-16 Hex Nyloc
39 7091304 3 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
40 7091305 3 SCREW, 3/8-16 x 2” Hex Head Cap, GR5
41 7091313 1 COTTER PIN, 3/32 x 1”
42 7091325 8 NUT, 1/2-13 Hex Nyloc
43 7091894 2 NUT, 1/2-13 Hex Center Lock
44 7054011 2 ASSEMBLY, Spindle see Cutter Housing Assembly

45 7057736 2 ASSEMBLY, Caster (Red) see Caster, Wheel & Tire

tionItem Qt

Note

page

Assembly page

Footnotes:

SERIES 1 & 2

39

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

48" & 52" MOWER DECK ASSEMBLY (Fixed Height)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

40

SERIES 1 & 2

48" & 52" MOWER DECK ASSEMBLY (Fixed Height)

p

y

Part No Descri

1 7013010 1 DECAL, Warning (CPSC Cut Finger)

2 7073647 1 DECAL, Danger Guard/Catcher

3 7023735 4 KNOB, Hood (5/16-18 thread)

4 7024156 1 DECAL, Caution- Operator Instruction

5 7027327 1 PIVOT, Roller Pin (Weldment)

6 7027344 2 WASHER, 5/8” Flat

7 7027950 1 SPRING, Chute

8 7029249 1 PULLEY, Driven, 5-3/4” O.D.
9A 7029261 1 * V-BELT, Secondary 48” (113” Long)
9B 7029266 1 * V-BELT, Secondary 52” (120” Long)

10A 7029262 1 * V-BELT, Primary 48” (66” Long)
10B 7029267 1 * V-BELT, Primary 52” (69” Long)

11 7072915 1 SPRING, Extension, Primary Idler
12 7029277 1 HINGE PIN, Chute
13 7029278 1 SPRING, Idler
14 7029281 4 STANDOFF, 4-1/2” Long (5/16-18 thread top; 3/8-16 bottom)
15 7091313 1 COTTER PIN, 3/32 x 1”
16 7046580 1 DECAL, SNAPPER Pro w/Trademark

17A 7058873 1 DEFLECTOR, 48” ANSI Compliant (Weldment)
17B 7058285 1 DEFLECTOR, 52” Euro Chute
18A 7054013 1 COVER, 48” Deck
18B 7054014 1 COVER, 52” Deck

19 7054020 2 ASSEMBLY, Caster Red (Fixed Deck) see Caster, Wheel & Tire

20A 7054022 1 ASSEMBLY, 48” Deck (Fixed Height) Deck weldment (7042461) plus

20B 7054027 1 ASSEMBLY, 52” Deck (Fixed Height) Deck weldment (7041809) plus

21 7054023 1 ASSEMBLY, Idler- 3 Spindle Deck
22 7076998 2 LUBE FITTING, 1/4-28 Straight
23 7079226 3 ROLLER, Low Density Polyethylene
24 7091299 8 NUT, 3/8-16 Hex Nyloc
25 7091304 8 BOLT, 3/8-16 x 1” Hex Head Cap, GR 5
26 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR5
27 7090613 4 NUT, 3/8-16 Hex Flange Lock
28 7046626 4 BUSHING, Caster
29 7054011 3 ASSEMBLY, Spindle see Cutter Housing Assembly

tionItem Qt

Note

Assembly page

4 bushings (7023556)

4 bushings (7023556)

Page

Footnotes:

SERIES 1 & 2

NOTE: * Part numbers are printed on belts.

41

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.1

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

42

SERIES 1 & 2

48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.1

p

y

Part No Descri

1 7063205 1 WELDMENT, 48” Deck replaces 7054036 (voided)

1 7045133 1 WELDMENT, 52” Deck

1 7045165 1 WELDMENT, 61” Deck

2 7058873 1 DEFLECTOR, 48” Deck ANSI Compliant (Weldment)

2 7058285 1 DEFLECTOR, 52” Deck Euro (Weldment)

2 7058291 1 DEFLECTOR, 61” Deck Euro (Weldment)

3 7029277 1 HINGE PIN, Chute

4 7027950 1 SPRING, Chute

5 7091313 1 COTTER PIN, 3/32 x 1”

6 7027327 1 PIVOT, Roller Pin (Weldment)

7 7091304 4 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5

8 7091299 29 NUT, 3/8-16 Hex Nyloc
8A 7091894 2 NUT, 1/2-13 Hex Center Lock

9 7079226 3 ROLLER, Low Density Polyethylene
10 7027344 2 WASHER, 5/8” Flat
11 7029264 2 WHEEL, Gage
12 7029265 2 BOLT, 1/2” Dia. Shoulder, 3/8-16 Thread
13 7034965 2 POINTER, Height-of-Cut
14 7091819 4 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap
15 7054023 1 ASSEMBLY, Idler - 3 Spindle Deck 48” & 61” Decks
15 7054420 1 ASSEMBLY, Idler - 3 Spindle Deck 52” Deck
16 7029259 2 STUD, Lift, 1/2-13 Thread, Both Ends
17 7091325 8 NUT, 1/2-13 Hex Nyloc
18 7029281 4 STANDOFF, 4-1/2” Long (5/16-18 thread top; 3/8-16 bottom)
19 7029280 2 STANDOFF, 2” Long (5/16-18 thread top ; 3/8-16 bottom)
20 7029261 1 * V-BELT, Secondary, 48” Deck (113” Nom. Eff. Length)
20 7029266 1 * V-BELT, Secondary, 52” Deck (120” Nom. Eff. Length)
20 7029268 1 * V-BELT, Secondary, 61” Deck (128” Nom. Eff. Length)
21 7029262 1 * V-BELT, Primary, 48” Deck (66” Nom. Eff. Length)
21 7042813 1 * V-BELT, Primary, 52” Deck (69” Nom. Eff. Length)
21 7042735 1 * V-BELT, Primary, 61” Deck (72” Nom. Eff. Length)
22 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
23 7029278 1 SPRING, Idler
24 7072915 1 SPRING, Extension, Primary Idler 48” Deck
24 7029272 1 SPRING, Extension, Primary Idler 52” & 61” Deck
25 7029258 16 BUSHING, Suspension
26 7091587 12 WASHER, 1/2” Flat

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

NOTE: * SNAPPER part number is printed on belt

43

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.1

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

44

SERIES 1 & 2

48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.1

p

y

Part No Descri

27 7029263 8 SLEEVE, Suspension all models
28 7034964 2 ARM, Suspension, 12” Long 48” & 52” Decks
28 7034979 4 ARM, Suspension, 13-1/2” Long 61” Deck
29 7029355 8 BOLT, 1/2-13 x 3-3/4” Hex Head, GR 5
30 7029249 1 PULLEY, 5-3/4” O.D. w/Hub 48” & 52” Decks
30 7029250 1 PULLEY, 6-5/8” Driven 61” Deck
31 7013010 1 DECAL, Warning (CPSC Cut Finger)
32 7073647 1 DECAL, Danger Guard/Catcher
33 7024156 1 DECAL, Caution- Operator Instruction

7054011 3 ASSEMBLY, Spindle see Cutter Housing Assembly

34A 7050513 1 ASSEMBLY, 48” Discharge Chute
34B 7500231 1 ASSEMBLY, 52” Discharge Chute
35A 7050590 1 WELDMENT, 48” Deflector Top
35B 7400008 1 WELDMENT, 52” Deflector Top
36A 7100621 1 CHUTE, Rubber (48”)
36B 7100623 1 CHUTE, Rubber (52”) replaces 7100087
37A 7078133 1 DEFLECTOR, Bottom (48”)
37B 7300036 1 DEFLECTOR, Bottom (52”)

38 7091790 4 BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5 used on 48” & 52” Decks only

tionItem Qt

Note

page

Footnotes:

SERIES 1 & 2

NOTE: * SNAPPER part number is printed on belt

45

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.2

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

46

SERIES 1 & 2

48", 52" & 61" MOWER DECK ASSY (Adj. Height) Pt.2

p

y

Part No Descri

1 7054035 1 WELDMENT, 48” Deck Frame

1 7041812 1 WELDMENT, 52” Deck Frame

1 7043865 1 WELDMENT, 61” Deck Frame

2 7021960 2 SPACER, Powdered Metal

3 7076998 2 FITTING, 1/4-28 Straight Lube

4 7046214 2 LIFT WASHER (Weldment)

5 7029260 1 WASHER, Lift 2 are used on 61” Decks

6 7054012 2 ASSEMBLY, Crank (Includes Crank, 7042477,

7 7035285 1 COVER, 48” Right

7 7046607 1 COVER, 52” Right

7 7035314 1 COVER, 61” Right

8 7035286 1 COVER, 48” Left

8 7046606 1 COVER, 52” Left

8 7035313 1 COVER, 61” Left

9 7035287 1 COVER, 48” Center

9 7035303 1 COVER, 52” Center

9 7035315 1 COVER, 61” Center
10 7023735 4 KNOB, Hood (5/16-18 thread)
11 7024085 2 WING NUT, 5/16-18
12 7046626 4 BUSHING
13 7044667 1 SHIELD, Muffler (SPA610, SPA611)
14 7091318 2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
15 7091298 2 NUT, 5/16-18 Hex Nyloc
16 7046580 1 DECAL, SNAPPER Pro w/Trademark
17 7029295 2 DECAL, Height of Cut
18 7043815 1 DECAL, Caution Handle May Be Hot (Adjustable Decks only)
19 7043816 1 DECAL, Oil Threads Here (Adjustable Decks only)
20 7400156 1 WELDMENT, Pro Knob used on 48” Deck only
21 7029259 2 STUD, Lift, 1/2-13 Thread, Both Ends
22 7029355 8 BOLT, 1/2-13 x 3-3/4” Hex Head, GR 5
23 7034964 2 ARM, Suspension, 12” Long 48” & 52” Decks
23 7034979 4 ARM, Suspension, 13-1/2” Long 61” Deck
24 7029258 16 BUSHING, Suspension
25 7029258 16 BUSHING, Suspension
26 7091587 12 WASHER, 1/2” Flat
27 7091325 8 NUT, 1/2-13 Hex Nyloc

tionItem Qt

Note

Handle 7029380 & Roll Pin

7013877)

Footnotes:

SERIES 1 & 2

47

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

36" DECK IDLER ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

48

SERIES 1 & 2

36" DECK IDLER ASSEMBLY

p

y

Part No Descri

1 7034422 1 PULLEY, Idler (5.00 O. D.)

2 7091299 4 NUT, 3/8-16 Hex Nyloc

3 7091300 2 WASHER, .44 x 1.0 x .08 Flat

4 7012709 1 RING, 1” External Retaining

5 7046626 2 BUSHING

6 7042448 1 IDLER ARM, 36” (Weldment)

7 7076998 1 GREASE FITTING, 1/4-28 Straight

8 7091304 3 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5

9 7041295 1 PIVOT, Idler Arm (Weldment)
10 7027220 1 BOLT, 3/8-16 x 3-1/4” Hex Head, GR 5
11 7029723 2 SPACER, .380 I.D. x 1” O.D. x .410 Thick
12 7027198 1 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5
13 7036429 1 BRACKET, Idler (Pro 36)
14 7035656 1 RETAINER, Belt - Idler
15 7091585 1 NUT, 3/8-16 Hex Center Lock, GR 5 or B

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

49

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

48" & 61" DECK IDLER ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

50

SERIES 1 & 2

48" & 61" DECK IDLER ASSEMBLY

p

y

Part No Descri

1 7029273 1 PULLEY, Idler

2 7034422 1 PULLEY, Flat Idler, 5” O.D.

3 7091299 2 NUT, 3/8-16 Hex Nyloc

4 7012709 2 RING, 1” External Retaining

5 7046626 4 BUSHING

6 7042452 1 WELDMENT, Idler Arm, Secondary

7 7042450 1 WELDMENT, Idler Arm, Primary

8 7035657 1 SPACER, Idler Pulley

9 7091300 2 WASHER, 3/8” Flat
10 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
11 7027220 1 BOLT, 3/8-16 x 3-1/4” Hex Head Cap, GR 5
12 7076998 1 LUBE FITTING, 1/4-28 Straight
13 7042465 1 WELDMENT, Idler Pivot
14 7035656 1 RETAINER, Belt - Idler
15 7023747 2 BUSHING, 1” I.D. Machine

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

51

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

52" DECK IDLER ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

52

SERIES 1 & 2

52" DECK IDLER ASSEMBLY

p

y

Part No Descri

1 7042465 1 WELDMENT, Idler Pivot

2 7023747 2 BUSHING, Machine

3 7046626 4 BUSHING, Flange

4 7042452 1 WELDMENT, Secondary Idler Arm

5 7076998 2 LUBE FITTING, 1/4-28 Straight

6 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5

7 7029273 1 PULLEY, Idler

8 7091300 4 WASHER, .44 x 1.0 x .08 Flat

9 7091299 2 NUT, 3/8-16 Hex Nyloc
10 7042775 1 WELDMENT, Primary Idler Arm, SPA521
11 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
12 7013847 1 RETAINER, 3/8” Bolt
13 7091302 1 NUT, 3/8-16 Hex, GR 5
14 7091585 1 NUT, 3/8-16 Hex Center lock
15 7027220 1 BOLT, 3/8-16 x 3-1/4” Hex Head, GR 5
16 7035657 1 SPACER, Idler Pulley
17 7034422 1 PULLEY, Idler (5.00 O. D.)
18 7012709 2 RING, 1” External Retaining

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

53

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

CUTTER HOUSING ASSEMBLY

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

54

SERIES 1 & 2

CUTTER HOUSING ASSEMBLY

p

y

Part No Descri

1 7029422 2 BEARING, Sealed

2 7029270 1 WASHER, Spindle

3 7029274 1 SNAP-RING, Spindle Shaft

4 7059311 1 ASSEMBLY, Spindle Shaft

5 7029254 1 SPACER, Bearing

6 7029271 4 SPACER, Blade
7A 7073395 3 BLADE, Commercial, 18” Low Lift for 36” (2 blades) or 52” decks

7B 7073396 3 BLADE, 21” Low Lift for 61” decks; (or use 7075770,

7C 7075771 3 BLADE, 16-1/2” for 48” deck

8 7016440 1 WASHER, Beveled

9 7029256 1 BOLT, 5/8-18 x 7-1/2” Hex Head Cap, GR 5
10 7029275 1 LUBE FITTING, 1/4-28 Straight (Thread Forming)
11 7029252 1 * HOUSING, Cutter
12 7029384 1 GREASE VENT, Spindle
13 7029302 6 BOLT, 3/8-16 x 1-1/4” Rib Necked
14 7029245 1 PULLEY, 5-3/4” O.D. for 48”, 52” & 61” decks
14 7029249 1 PULLEY, 5-3/4” O.D. w/Hub for 36” deck
15 7091736 1 NUT, 5/8-18 Hex Flange Lock, GR 5
16 7091299 6 NUT, 3/8-16 Hex Nyloc
17 7063238 1 ** SEAL, Nylos
18 7013370 1 ** WASHER

tionItem Qt

Note

(3 blades)

high lift blade)

Footnotes:

SERIES 1 & 2

NOTE: * 7054017, Spindle Housing sub-assembly is made of items 11, 12 & 13.
NOTE: ** To install Bearing Pre-Seal Kit (7063240) discard item 3 & replace with items 17 & 18 as shown.

Manual No. 700692 8PRO HYDRO

55

TP 400-5023-4-CW-N

DECALS - Left & Right Panels

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

56

SERIES 1 & 2

DECALS - Left & Right Panels

p

y

Part No Descri

1 7074257 1 DECAL, Left Panel, Engine Control w/Choke

2 7075755 1 DECAL, Left Panel, Throttle w/Choke (Hydro)

3 7029311 1 DECAL, Left Panel, Engine Control w/o Choke

4 7073592 1 DECAL, Left Panel, Throttle w/o Choke (Hydro)

5 7029045 1 DECAL, Right Panel, Instruction

6 7073591 1 DECAL, Right Panel, Instruction

7 7075758 1 DECAL, Right Panel, Instructions

8 7029041 1 DECAL, Left Panel, Switch replaced by 7073597

9 7073597 1 DECAL, Left Panel, Switch
10 7075757 1 DECAL, Left Panel, Switch
11 7029044 1 DECAL, Right Panel, Switch
12 7029310 1 DECAL, Right Panel, Switch, Electric Start
13 7073595 1 DECAL, Right Panel, Switch, Electric Start (Hydro)
14 7029295 1 DECAL, Height of Cut
15 7043816 1 DECAL, Oil Threads Here (Adjustable Decks only)

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

57

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

DECALS - Instructions, Caution, Warning, Danger

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

58

SERIES 1 & 2

DECALS - Instructions, Caution, Warning, Danger

p

y

Part No Descri

1 7029866 1 DECAL, Caution/Operation, Pro Hydro

2 7073647 1 DECAL, Danger Guard/Catcher

3 7073605 1 DECAL, Warning/Operation Pro Hydro

4 7073594 1 DECAL, Caution, Open Belt Drive

5 7073593 1 DECAL, Caution, Adjustment Handle

6 7043815 1 DECAL, Caution Handle May Be Hot (Adjustable Decks only)

7 7046580 1 DECAL, Snapper Pro w/Trademark (white letters)

7 7075568 1 DECAL, Snapper Pro w/Trademark (silver letters)

7A 7074862 1 DECAL, Snapper Pro (silver, 16-1/2” long)

8 7024903 1 SNAPPER LOGO, 8” Molded-White

9 7027733 1 DECAL, Ear Protection
10 7013010 1 DECAL, Danger (CPSC) Cut Finger
11 7024156 1 DECAL, Caution- Operator Instruction
12 7073590 1 DECAL, Warning! Counterweight
13 7044796 1 DECAL, 36” Deck Commercial white numbers
13 7075564 1 DECAL, 36” Deck Commercial silver numbers
14 7044792 1 DECAL, 48” Deck Commercial white numbers
14 7075565 1 DECAL, 48” Deck Commercial silver numbers
15 7044793 1 DECAL, 52” Deck Commercial white numbers
15 7075566 1 DECAL, 52” Deck Commercial silver numbers
16 7044794 1 DECAL, 61” Deck Commercial white numbers
16 7075567 1 DECAL, 61” Deck Commercial silver numbers
17 1 DECAL, Patent Numbers not shown; not a service part

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

59

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

ELECTRICAL WIRING (Manual Start)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

60

SERIES 1 & 2

ELECTRICAL WIRING (Manual Start)

p

y

Part No Descri

1 7073118 1 WIRING HARNESS for all models except for Kohler

2 7027226 1 HARNESS, Wiring Pigtail for Kawasaki 14HP

3 7041692 1 HARNESS, Wiring Pigtail used on SPLH171KW only

4 7074852 1 HARNESS, Wiring Pigtail

5 7028513 1 WIRE, Kohler Engine Ground

tionItem Qt

Note

23HP

Footnotes:

SERIES 1 & 2

61

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

ELECTRICAL WIRING- LOOP HANDLE (Electric Start)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

62

SERIES 1 & 2

ELECTRICAL WIRING- LOOP HANDLE (Electric Start)

p

y

Part No Descri

1 7073117 1 WIRING HARNESS

2 7046901 1 HARNESS, Regulator, Kawasaki

3 7012444 1 COVER, Battery Cover

4 7014476 1 WIRE, Solenoid to Battery red, 11” long

5 7011859 1 WIRE, Negative black, 9” long

6 7029061 1 WIRE, Positive red, 8/9” long

7 7015063 1 CLIP, Battery Hose not shown

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

63

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

WIRING SCHEMATIC (Manual Start)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

64

SERIES 1 & 2

WIRING SCHEMATIC (Manual Start)

p

y

Part No Descri

1 7073118 1 WIRING HARNESS

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

65

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

WIRING SCHEMATIC (Electric Start)

Manual No. 7006928 PRO HYDRO
TP 400-5023-4-CW-N

66

SERIES 1 & 2

WIRING SCHEMATIC (Electric Start)

p

y

Part No Descri

1 7073117 1 WIRING HARNESS

tionItem Qt

Note

Footnotes:

SERIES 1 & 2

67

Manual No. 700692 8PRO HYDRO

TP 400-5023-4-CW-N

Parts Manual fo

r

O

S

PRO HYDR

MID-SIZE WALK BEHIND MOWER

SERIES 1 & 2

COPYRIGHT ©2006

SNAPPER PRODUCTS, INC.

ALL RIGHTS RESERVED.

IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS

WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE

RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS

AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE

SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.

McDonough, GA, 30253 U.S.A.

Manual No. 7006928

Revision 4,

11/7/2006

TP 400-5023-4- C W-N