Page 1
Parts Manual fo
r
Z
RZT TWIN STICK HYDRO DRIVE 250
38" & 42"
SERIES 0 & 1
MODEL
RZT185380BVE (7800009)
RZT185381BVE (7800151)
RZT20420BVE2 (7800010)
RZT20421BVE2 (7800152)
Briggs & Startton Yard Power Products Group
Copyright © 2007
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
Revision C,
McDonough, GA, 30253 U.S.A.
10/30/2007
Manual No. 7006460
TP 400-5164-C-HZ-N
Page 2
Page 3
s
PAGE GROUP
4
6
8
10
12
16
20
22
24
26
30
34
36
38
40
42
44
46
48
50
52
54
WHEEL GROUP
FRONT AXLE GROUP
FRAME GROUP
TRANSAXLE GROUP
CONTROL GROUP, LH
CONTROL GROUP, RH
PARK BRAKE GROUP
SNAPPER FENDER GROUP
SEAT GROUP
ENGINE GROUP (18.5 HP Briggs)
ENGINE GROUP (20 HP Briggs)
DECAL GROUP
DECK LIFT GROUP (38/42)
38" DECK GROUP (Sub-Assembly)
38" DECK GROUP (Final Assembly)
38" DECK SPINDLE
42" DECK GROUP (Sub-Assembly)
42" DECK GROUP (Final Assembly)
42" DECK SPINDLE
ELECTRICAL GROUP
WIRING HARNESS
WIRING SCHEMATIC (Briggs Engine)
Table Of Content
SERIES 0 & 1
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
3
TP 400-5164-C-HZ-N
Page 4
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
4
SERIES 0 & 1
Page 5
WHEEL GROUP
p
y
Part No Descri
1 7059090 2 ASSEMBLY, Front Wheel & Tire
2 7039477 1 RIM, Caster Wheel
3 7035618 1 TIRE, 11 x 4.00-5, Smooth Tread
4 7035358 2 BALL BEARING, .625 x 1.38
5 7029275 1 GREASE FITTING, 1/4-28 thread forming Alemite #3038-B
6 7012234 1 VALVE STEM, Snap In
7 7091772 2 SCREW, 7/16-14 x 6”, Hex Head Cap, GR 5
8 7035359 2 TUBE, 5/8 O.D. x 14 Ga. Wall x 4.510” long caster wheel spacer
9 7090839 2 NUT, 7/16-14 Hex Center Lock, GR 5 or B
10 7050539 2 ASS'Y, 18 x 6.50-8 Tire/Wheel, Turf-Master used on RZT185380BVE
11 7078114 1 RIM, 18 x 6.50, 4 Bolt
12 7078119 1 TIRE, 18 x 6.50-8, Turf Master
13 7050538 2 ASS'Y, 18 x 8.50-8 Tire/Wheel, Turf-Master used on RZT20420BVE2
14 7078113 1 RIM, 18 x 8.50, 4 Bolt
15 7078109 1 TIRE, 18 x 8.50-8, Turf Master
16 7027192 8 LUG NUT 1/2-20 Tapered Seat YZ
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
5
TP 400-5164-C-HZ-N
Page 6
FRONT AXLE GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
6
SERIES 0 & 1
Page 7
FRONT AXLE GROUP
p
y
Part No Descri
1 7100321 1 FRONT AXLE, Cast (Cardinal Red)
2 7013864 3 LUBE FITTING, 3/16” Press-In
3 7400075 2 WELDMENT, Caster (Cardinal Red)
4 7013855 4 THRUST WASHER, 1” I.D.
5 7012709 2 RETAINING RING, 1” External
6 7091558 1 SCREW, 1/2-13 x 3-1/2” Hex Head Cap, YZ
7 7090250 2 WASHER, 1/2” SAE Flat
8 7011309 2 SPACER, Axle Pivot
9 7012706 2 BEARING SLEEVE
10 7091894 1 NUT, 1/2-13 Hex Center Lock, GR 5, YZ
11 7091703 2 SCREW, 7/16-20 x 2-1/2” Hex Head Cap, GR 5 (Special Head)
12 7091595 4 WASHER, .47 x .92 x .065 Flat
13 7090377 2 NUT, 7/16-20 Hex Center Lock Jam, GR 5 or B
14 7300080 1 BRACKET, Quick Hitch
15 7200028 2 SWIVEL, 3/8-16 Inline
16 7032030 2 WASHER, 13/32 x 1-1/4” Flat
17 7091299 2 NUT, 3/8-16 Hex Nyloc
18 7300187 1 BRACKET, Axle (Cardinal Red)
19 7091905 6 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
20 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR 5
21 7091508 8 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
22 7091706 20 NUT, 5/16-18 Hex Top Lock, GR B
23 7100417 2 PLATE, Friction
24 7077683 8 SCREW, 5/16-18 x 1” Flat Head Countersunk
25 7300004 2 BRACKET, Axle Support
26 7090188 8 WASHER, .34 x .69 x .08 Flat
27 7091318 4 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5, YZ
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
7
TP 400-5164-C-HZ-N
Page 8
FRAME GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
8
SERIES 0 & 1
Page 9
FRAME GROUP
p
y
Part No Descri
7500012 1 SUB-ASSEMBLY, Frame, (Red Paint) includes 22 Items shown below
1 7300181 1 FRAME, RZT (Cardinal Red)
2 7091601 12 NUT, 5/16-18 Hex Flange Lock, GR 5
3 7300006 1 TANK BRACKET
4 7091811 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
5 7300184 1 FOOTREST, Snapper (Cardinal Red)
6 7091508 6 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
7 7300226 1 PLATE, Rear Seat Guard
8 7091905 8 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
9 7043307 1 HEAT SHIELD finish: black powder coat
10 7043309 2 BRACKET, Body Support
11 7091742 2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap, GR 5
12 7300342 2 BRACE, Hood/Fender
13 7091070 2 NUT, 5/16-18 Hex Flange Lock, GR 5
14 7091894 1 NUT, 1/2-13 Hex Center Lock, GR 5, YZ
15 7044760 1 SPRING, Torsion, RH Wind
16 7400021 1 WELDMENT, Hydro Idler
17 7200034 1 SPACER, Hydro Idler
18 7091587 1 WASHER, .531 x 1.062 x .121 Flat, YZ
19 7091218 1 SCREW 1/2-13 x 2-1/2” Hex Head Cap, GR 5 (Black Phosphate)
20 7100103 1 IDLER, 3.25” OD x .391 ID x 1.63 Backside
21 7090122 1 WASHER, 3/8” Flat SAE
22 7091585 1 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
23 7100266 1 MAT, Foot Rest RZT
24 7100287 1 MAT, Floor Pan
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
9
TP 400-5164-C-HZ-N
Page 10
TRANSAXLE GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
10
SERIES 0 & 1
Page 11
TRANSAXLE GROUP
p
y
Part No Descri
1 7400020 1 WELDMENT, Transaxle Support
2 7100229 2 ROD, Roll Release
3 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
4 7012431 2 HAIR PIN, 1-1/8”
5 7091867 8 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap, GR 2
6 7014664 2 SHOULDER BOLT, 5/16-18 .530 long shoulder
7 7091298 12 NUT, 5/16-18 Hex Nyloc
8 7078112 1 TRANSAXLE, LH RZT ZA-AHBB-2D5A-2DCX
9 7078111 1 TRANSAXLE, RH RZT ZA-DHBB-2D5A-2DCX
10 7300082 1 BRACKET, Anti-Rotation
11 7200046 1 PIN, Anti-Rotation, RZT Clutch
12 7091601 1 NUT, 5/16-18 Hex Flange Lock, GR 5
13 7091908 2 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5, YZ
14 7091830 4 SCREW, 5/16-18 x 3” Hex Head Cap, GR 5, YZ
15 7015686 8 SHIM WASHER, 5/16” I.D.
16 7091944 4 SCREW 5/16-18 x 2-3/4” Hex Head Cap, GR 5, YZ
17 7300000 2 BRACKET, Transaxle Support
18 7100102 1 V-BELT, HA Sect. (wrapped) 58.00 effective length hydro drive
19 7090188 8 WASHER, .34 x .69 x .08 Flat
20 7091703 2 SCREW, 7/16-20 x 2-1/2” Hex Head Cap, GR 5 (Special Head)
21 7090377 2 NUT, 7/16-20 Hex Center Lock Jam, GR 5 or B
22 2159106 1 SPRING, Extention, .562 OD x 4.250 long x .049 Wire B
23 1735484 2 ARM, Control Kit (Used for both R.H. & L.H.
tionItem Qt
Note
Transaxle)
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
11
TP 400-5164-C-HZ-N
Page 12
CONTROL GROUP, LH
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
12
SERIES 0 & 1
Page 13
CONTROL GROUP, LH
p
y
Part No Descri
1 7043338 1 HANDLE
2 7043336 1 WELDMENT, LH Control Arm
3 7100051 1 FOAM GRIP, Handle
4 7013874 2 BUSHING
5 7043301 1 WELDMENT, Control Bracket, LH
6 7900016 1 WASHER, 5/8 ID x 1.00 OD x .065 Nylon
7 7027344 1 WASHER, 5/8” Flat SAE
8 7011121 1 WASHER, .64 x 1.12 x .028 Beveled
9 7090658 2 NUT, 5/8-18 Hex Jam
10 7200012 1 SHOULDER BOLT, 3/8-16 2.013 long shoulder
11 1670971 1 THRUST WASHER, .562 ID x 1.000 OD x .030/.032 Thick
12 7014409 2 FLANGE BEARING, 9/16 I.D. P.M. powdered metal
13 7091299 2 NUT, 3/8-16 Hex Nyloc or 7091585, 3/8-16 Hex Center
14 7900003 1 SHOULDER BOLT, 5/16 x 1/4-20 .800 long shoulder
15 5022978 1 DAMPENER, Hydraulic
16 7200006 1 SPACER, 9/16 OD x 12GA x .325
17 7100415 2 WASHER, 1/4” I.D. Flat case hardened steel
18 7091603 2 NUT, 1/4-20 Hex Nyloc or item 22
19 7900002 1 SHOULDER BOLT, 5/16 x 1/4-20 1.360 long shoulder
20 7200005 1 SPACER, 9/16 OD x 12GA x .899
21 7900029 2 SCREW, 1/4-20 x1-1/4” Hex Head Cap, GR 5
22 7092126 2 NUT 1/4-20 Hex Center Lock, GR 5 YZ
23 7091686 8 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
24 7300009 1 PLATE, Fwd/Rev Adjust
25 7300010 1 TRACK, Control Stick L.H.
26 7043302 1 CONTROL BRACKET, LH
27 7091304 4 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5, YZ
28 7091619 4 NUT, 3/8-16 Hex Flange Lock
29 7300264 1 BRACKET, Rod Holder, RZT
30 7091095 2 POP RIVET, 1/8 x 3/8”
7500349 1 ASSEMBLY, Fwd/Rev Rod (was 7500059); incl. items 31,
31 7027936 1 ROD END
32 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
33 7091630 3 NUT, 3/8-24 Hex, GR B, YZ
34 7090517 3 WASHER, 3/8” Flat
35 7074511 1 SPRING, Compression (Brake)
36 7200009 1 ROD, Link Fwd./Rev. (3/8-24 thread)
tionItem Qt
Note
Lock Nut
33, 34, 35 & 36
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
13
TP 400-5164-C-HZ-N
Page 14
CONTROL GROUP, LH
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
14
SERIES 0 & 1
Page 15
CONTROL GROUP, LH
p
y
Part No Descri
37 7900000 1 CLEVIS PIN, 7/16 x 1”
38 7091594 1 COTTER PIN, 1/2 Self Locking, YZ
39 7100487 1 CLIP, Spring
40 7300489 1 BRACKET, Fender Support, LH RZT
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
15
TP 400-5164-C-HZ-N
Page 16
CONTROL GROUP, RH
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
16
SERIES 0 & 1
Page 17
CONTROL GROUP, RH
p
y
Part No Descri
1 7043338 1 HANDLE
2 7200004 1 ROD, Handle R.H.
3 7100051 1 FOAM GRIP, Handle
4 7900029 2 SCREW, 1/4-20 x1-1/4” Hex Head Cap, GR 5
5 7092126 2 NUT 1/4-20 Hex Center Lock, GR 5 YZ
6 7091628 1 WASHER, .64 x .99 x .05 Flat, YZ
7 7013874 2 BUSHING
8 7400001 1 WELDMENT, Control Bracket, RH
9 7900016 1 WASHER, 5/8 ID x 1.00 OD x .065 Nylon
10 7027344 1 WASHER, 5/8 SAE Flat
11 7011121 1 WASHER, .64 x 1.12 x .028 Beveled
12 7090658 2 NUT, 5/8-18 Hex Jam
13 7091686 6 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
14 7300009 1 PLATE, Fwd/Rev Adjust
15 7300008 1 TRACK, Control Stick, R.H.
16 7400006 1 WELDMENT, Lift Bracket
17 7091304 4 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5, YZ
18 7091619 4 NUT, 3/8-16 Hex Flange Lock
19 7300032 1 BRACKET, Switch
20 7023355 1 SWITCH- DPDT also shown in Electrical Group
21 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
22 7091299 2 NUT, 3/8-16 Hex Nyloc
23 7014409 2 FLANGE BEARING, 9/16 I.D. P.M. powdered metal
24 1670971 1 THRUST WASHER, .562 ID x 1.000 OD x .030/.032 Thick
25 7200012 1 SHOULDER BOLT, 3/8-16 2.013 long shoulder
26 7900003 1 SHOULDER BOLT, 5/16 x 1/4-20 .800 long shoulder
27 7900002 1 SHOULDER BOLT, 5/16 x 1/4-20 1.360 long shoulder
28 5022978 1 DAMPENER, Hydraulic
29 7200006 1 SPACER, 9/16 OD x 12GA x .325
30 7100415 2 WASHER, 1/4” I.D. Flat case hardened steel
31 7091603 2 NUT, 1/4-20 Hex Nyloc
32 7200005 1 SPACER, 9/16 OD x 12GA x .899
33 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
7500059 1 ASSEMBLY, Fwd/Rev Rod incl. next 5 items
34 7027936 1 ROD END
35 7091630 3 NUT, 3/8-24 Hex, GR B, YZ
36 7090517 3 WASHER, 3/8” Flat
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
17
TP 400-5164-C-HZ-N
Page 18
CONTROL GROUP, RH
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
18
SERIES 0 & 1
Page 19
CONTROL GROUP, RH
p
y
Part No Descri
37 7074511 1 SPRING, Compression (Brake)
38 7200009 1 ROD, Link Fwd./Rev. (3/8-24 thread)
39 7900000 1 CLEVIS PIN, 7/16 x 1”
40 7091594 1 COTTER PIN, 1/2 Self Locking, YZ
41 7300354 1 BRACKET, Fender Support, RH
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
19
TP 400-5164-C-HZ-N
Page 20
PARK BRAKE GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
20
SERIES 0 & 1
Page 21
PARK BRAKE GROUP
p
y
Part No Descri
1 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)
2 7091298 1 NUT, 5/16-18 Hex Nyloc
3 7091811 2 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
4 7043312 1 BRACKET, Park Brake, LH Lower
5 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
6 7024159 1 COTTER PIN, 3/8” Self-Locking
7 7200007 1 ROD, Park Brake
8 7043311 1 BRACKET, Park Brake, RH Lower
9 7091192 1 WASHER, 1/2 x .090 Flat
10 7025074 1 WASHER, .531 x 1.0 x .063 Flat
11 7011078 1 SHOULDER BOLT, 5/16-18 x 1” .220 long shoulder
12 7043335 1 ROD, Park Brake (1/4-20 thread)
13 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
14 7100100 1 SPRING, Compression
15 7300007 1 BRACKET, Park Brake
16 7091495 2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
17 7091705 1 NUT, 1/4-20 Hex Top Lock, GR B or 7092126, 1/4-20 Hex Center
18 7090122 2 WASHER, 3/8” Flat SAE
19 7091594 3 COTTER PIN, 1/2 Self Locking, YZ
20 7900005 1 ROD, Hanger (1/4-20 both ends)
21 7091603 4 NUT, 1/4-20 Hex Nyloc YZ
22 7091290 1 NUT, 10-24 Hex Nyloc
23 7043310 1 HOOK, Park Brake
24 7023355 1 SWITCH- DPDT also shown in Electrical Group
tionItem Qt
Note
Lock Nut, Grade 5
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
21
TP 400-5164-C-HZ-N
Page 22
SNAPPER FENDER GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
22
SERIES 0 & 1
Page 23
SNAPPER FENDER GROUP
p
y
Part No Descri
1 7100007 1 FENDER, LH RZT
2 7100006 1 FENDER, RH RZT
3 7091811 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
4 7011791 4 BOLT RETAINER, 5/16” Black
5 7090951 4 NUT, 5/16-18 Hex Large Flange Center Lock
6 7300178 1 COVER, Front, Snapper
7 7091819 2 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap, YZ
8 7300112 1 PANEL, Control
9 7090999 5 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)
10 7023295 3 U-NUT 1/4-20
11 7300283 1 BRACKET, RH Fender Support (Cardinal Red)
12 7091905 2 BOLT, 5/16-18 x 7/8” Hex Flange Lock, YZ
13 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
14 7100112 1 COVER, Engine, Double Vent
15 7091890 2 WASHER, 1/4” Internal/External Tooth Lock
16 7100825 2 3-PRONG KNOB, 1/4-20 x 1/2” was 7023341
17 7100012 1 GUARD, Rear Seat
18 7900023 2 SCREW, 1/4-15 x 1-1/4” Hex Washer Self-Tap
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
23
TP 400-5164-C-HZ-N
Page 24
SEAT GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
24
SERIES 0 & 1
Page 25
SEAT GROUP
p
y
Part No Descri
1 7100005 1 ASSEMBLY, 15” Seat, w/Armrests Ref. Michigan Seat Co.
2 7300057 1 SEAT PLATE
3 7023191 2 KNOB, Three Prong, 5/16-18 thread
4 7090187 2 WASHER, 5/16” Split Lock
5 7043316 1 BRACKET, Seat Support
6 7091304 2 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5, YZ
7 7090390 2 WASHER, 3/8” Internal Tooth Lock
8 7091619 2 NUT, 3/8-16 Hex Flange Lock
9 7091591 2 BOLT, 5/16-18 x 1” Hex Flange Lock, GR 5, YZ
10 7074218 2 SPRING, Compression- Seat Support
11 7091298 4 NUT, 5/16-18 Hex Nyloc
12 7200008 1 ROD, Seat Hinge
13 7024159 1 COTTER PIN, 3/8” Self-Locking
14 7011078 2 SHOULDER BOLT, 5/16-18 x 1” .220 long shoulder
15 7091742 2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap, GR 5
16 7091315 2 WASHER, 5/16” Split Lock
17 7014098 2 WASHER, .34 x 1.0 x .09 Flat
18 7028620 2 SPACER, .340 I.D. x .63 O.D. x .310 Thick
19 7043308 1 BRACKET, Lower Seat
20 7091318 2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5, YZ
21 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
22 7091198 1 HWST, 3/8-16 X5/8 (See image note about 12 & 13)
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
25
TP 400-5164-C-HZ-N
Page 26
ENGINE GROUP (18.5 HP Briggs)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
26
SERIES 0 & 1
Page 27
ENGINE GROUP (18.5 HP Briggs)
p
y
Part No Descri
1 1730219 1 * ENGINE, 18.5 HP Briggs, Intek Model 31P777 0121 B1
2 7090324 4 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
3 7043343 1 ASSEMBLY, Engine Pulley
4 7013250 1 KEY, 1/4 Square x 1”
5 1717664 1 CLUTCH, Ogura JD-11
6 7029138 1 WASHER, .468 ID x 1.50 OD x .188 Flat
7 7091301 1 WASHER, 7/16” Split Lock
8 7092130 1 SCREW, 7/16-20 x 4-1/2” Hex Head Cap, GR 5
9 1726498 1 HOSE, Oil Drain
10 7900020 1 HARNESS CLIP, 5/8”
11 7091867 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap, GR 2
12 7028564 1 CABLE, 26.25” Throttle Control
13 7100529 1 KNOB, Throttle, Red RZT
14 7091195 1 SCREW, #10-16 x 3/4” Pan Head Self-Tap
15 7090999 2 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)
16 7100797 1 CABLE, 30” Choke Control
17 7090390 1 WASHER, 3/8” Internal Tooth Lock
18 7090155 1 NUT, 3/8-24 Hex, GR B
19 7012080 3 CABLE TIE, 7”
20 7100101 1 MANIFOLD, 18 HP B&S Intek
21 7100160 1 MUFFLER, RZT
22 7015352 1 GASKET, Exhaust
23 7091315 3 WASHER, 5/16” Split Lock
24 7091738 2 SET SCREW, 5/16-18 x 3/4” Socket Head, GR 8
25 7090290 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
26 7300237 1 BRACKET, Muffler 18HP Briggs
27 7091495 1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
28 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
29 7090052 1 WASHER, 1/4” Split Lock
30 7091576 1 NUT, 1/4-20 Hex, GR 5 or B
31 7078234 1 ASSEMBLY, Clamp B&S P/N's 223434, 93877 &
32 7500077 1 ASSEMBLY, Fuel Tank, RZT includes items 33 thru 37
33 7100037 1 FUEL TANK, 3 Gal.
34 7100283 1 DIP TUBE
35 7012337 1 GROMMET
36 7075288 1 ELBOW, 90 Degree
37 1715917 1 CAP, Fuel, 3-1/2”
tionItem Qt
Note
93203
Footnotes:
NOTE: * Purchase engine parts from engine manufacturer dealer.
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
27
TP 400-5164-C-HZ-N
Page 28
ENGINE GROUP (18.5 HP Briggs)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
28
SERIES 0 & 1
Page 29
ENGINE GROUP (18.5 HP Briggs)
p
y
Part No Descri
38 7012222 4 CLAMP, Fuel Line
39 7073240 2 HOSE, Fuel, 5”
40 7016325 1 VALVE, Fuel Shut-Off
41 7100312 1 SEAL, Tank
42 7091908 1 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5, YZ
43 7090188 2 WASHER, .34 x .69 x .08 Flat
44 7091511 1 NUT, 5/16-18 Hex, GR 5 or B
45 7091928 1 BOLT, 5/16-18 x 1-1/4” Square Neck Carriage
46 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
47 7100666 1 CLAMP, Muffler B&S part # 222825
tionItem Qt
Note
Footnotes:
NOTE: * Purchase engine parts from engine manufacturer dealer.
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
29
TP 400-5164-C-HZ-N
Page 30
ENGINE GROUP (20 HP Briggs)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
30
SERIES 0 & 1
Page 31
ENGINE GROUP (20 HP Briggs)
p
y
Part No Descri
1 1729722 1 * ENGINE, 20 HP Briggs Intek Twin Model 441577 0118 B1
2 7090324 4 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
3 7043343 1 ASSEMBLY, Engine Pulley
4 7013250 1 KEY, 1/4 Square x 1”
5 1717664 1 CLUTCH, Ogura JD-11
6 7029138 1 WASHER, .468 ID x 1.50 OD x .188 Flat
7 7091301 1 WASHER, 7/16” Split Lock
8 7092130 1 SCREW, 7/16-20 x 4-1/2” Hex Head Cap, GR 5
9 1726498 1 HOSE, Oil Drain
10 7900020 1 HARNESS CLIP, 5/8”
11 7091867 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap, GR 2
12 7075449 1 CABLE, 48” Throttle Control B&S 16HP Single Intek
13 7100529 1 KNOB, Throttle, Red RZT
14 7091195 1 SCREW, #10-16 x 3/4” Pan Head Self-Tap
15 7090999 2 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)
16 7100416 1 CABLE, 54” Choke Control
17 7090390 1 WASHER, 3/8” Internal Tooth Lock
18 7090155 1 NUT, 3/8-24 Hex, GR B
19 7012080 3 CABLE TIE, 7”
20 7078122 1 MANIFOLD, B&S V-Twin Intek
21 7100160 1 MUFFLER, RZT
22 7063283 2 GASKET, Exhaust, 20 HP Intek
23 7091315 5 WASHER, 5/16” Split Lock
24 7091738 4 SET SCREW, 5/16-18 x 3/4” Socket Head, GR 8
25 7091906 5 SCREW, 1/4-20 x 3/4” Hex Head Flange, GR 5, YZ
26 7300238 1 BRACKET, Muffler 20/22HP Briggs
27 7091495 1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
28 7091294 2 WASHER, .28 x .63 x .06 Flat, GR 5
29 7090052 1 WASHER, 1/4” Split Lock
30 7091576 1 NUT, 1/4-20 Hex, GR 5 or B
31 7078234 1 ASSEMBLY, Clamp B&S P/N's 223434, 93877 &
32 7500077 1 ASSEMBLY, Fuel Tank, RZT includes items 33 thru 37
33 7100037 1 FUEL TANK
34 7100283 1 DIP TUBE
35 7012337 1 GROMMET
36 7075288 1 ELBOW, 90 Degree
37 1715917 1 CAP, Fuel, 3-1/2”
tionItem Qt
Note
93203
Footnotes:
NOTE: * Purchase engine parts from engine manufacturer dealer.
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
31
TP 400-5164-C-HZ-N
Page 32
ENGINE GROUP (20 HP Briggs)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
32
SERIES 0 & 1
Page 33
ENGINE GROUP (20 HP Briggs)
p
y
Part No Descri
38 7012222 4 CLAMP, Fuel Line
39A 7073240 1 HOSE, Fuel, .25 I.D. x 5” long
39B 7029982 1 HOSE, Fuel, .25 I.D. x 14” long
40 7016325 1 VALVE, Fuel Shut-Off
41 7100312 1 SEAL, Tank
42 7091908 1 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5, YZ
43 7090188 2 WASHER, .34 x .69 x .08 Flat
44 7091511 1 NUT, 5/16-18 Hex, GR 5 or B
45 7200055 1 TUBE, Manifold Extension
46 225477 1 Bracket, Fuel Pump Briggs part
47 7091928 1 BOLT, 5/16-18 x 1-1/4” Square Neck Carriage
48 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
49 7100666 1 CLAMP, Muffler B&S part # 222825
tionItem Qt
Note
Footnotes:
NOTE: * Purchase engine parts from engine manufacturer dealer.
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
33
TP 400-5164-C-HZ-N
Page 34
DECAL GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
34
SERIES 0 & 1
Page 35
DECAL GROUP
p
y
Part No Descri
1 7100467 1 DECAL, Ignition, RZT
2 7100335 1 DECAL, Snapper Fender, RH
3 7100334 1 DECAL, Snapper Fender, LH
4 7100505 1 DECAL, Snapper
5 7100413 1 DECAL, Throttle Control, RZT
6 7100331 1 DECAL, Warning, Operation
7 7100340 1 DECAL, Height Of Cut, RZT
8 7100333 1 DECAL, Motion Control, RZT
9 7100332 1 DECAL, Park Brake, RZT
10 7100341 1 DECAL, Roll Release, RZT
11 7046720 1 DECAL, Chute/Deflector
12 7013010 2 DECAL, Danger, (Cut Finger)
13 7100420 1 DECAL, 250 Z 18.5HP RZT
14 7100421 1 DECAL, 250 Z 20HP RZT
15 7026154 1 DECAL, 38 Inch
16 7024910 1 DECAL - 42 INCH
17 1 DECAL, OPEI Walk/Ride not shown, not a service part
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
35
TP 400-5164-C-HZ-N
Page 36
DECK LIFT GROUP (38/42)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
36
SERIES 0 & 1
Page 37
DECK LIFT GROUP (38/42)
p
y
Part No Descri
1 7300037 1 HANDLE, Deck Lift
2 7091588 2 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR 5, YZ
3 1722302 1 HANDLE GRIP, Black Flexible (Simplicity)
4 7400011 1 WELDMENT, Deck Lift, 38/42
5 7100210 2 LINK, Leveling, 3/8-16 thread (2)
6 7090122 8 WASHER, 3/8” Flat SAE
7 7091585 8 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
8 7027172 4 SCREW, 1/4-20 x 5/8” Hex Head Cap. GR 5
9 7091603 4 NUT, 1/4-20 Hex Nyloc
10 7091619 2 NUT, 3/8-16 Hex Flange Lock
11 7026196 1 FLANGE BEARING, 3/4” I.D. powdered metal
12 7091658 6 JAM NUT, 3/8-16, YZ
13 7028037 2 SWIVEL, Inline Brake Arm
14 7100125 2 PIN, Quick Hitch
15 7300024 2 BAR, Rear Lift, 38/42
16 7091503 4 HAIR PIN, 3/32 x 1-1/2”
17 7014981 2 SHOULDER BOLT, 3/8-24, GR 8 .285” long shoulder
18 7300028 2 BRACKET, Deck Hanger
19 7090289 2 NUT, 3/8-24 Hex Center Lock
20 7091811 4 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR 5
21 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR 5
22 7200019 1 ROD, Deck Hanger Front 38/42
23 7091299 2 NUT, 3/8-16 Hex Nyloc
24 7200028 2 SWIVEL, 3/8-16 Inline
25 7032030 2 WASHER, 13/32 x 1-1/4” Flat
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
37
TP 400-5164-C-HZ-N
Page 38
38" DECK GROUP (Sub-Assembly)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
38
SERIES 0 & 1
Page 39
38" DECK GROUP (Sub-Assembly)
p
y
Part No Descri
1 7300271 1 DECK, 38 RZT (Cardinal Red) was 7300160 (Raw 38” Deck)
2 7059377 2 ASSEMBLY, 38” Spindle
3 7010817 1 FITTING, Lube, Press-In (for .187 dia. Hole)
4 7072440 2 SPACER, 38 Spindle Pulley
5 7100278 2 PULLEY, 5.0 O. D.
6 7090658 2 NUT, 5/8-18 Hex Jam
7 7090595 14 BOLT, 5/16-18 x 3/4” Hex Flange Lock
8 7091601 19 NUT, 5/16-18 Hex Flange Lock, GR 5
9 7300031 1 BRACKET, Front, 38” RZT
10 7091026 2 BOLT, 5/16-18 x 3/4” Short Square Neck Carriage, GR 5
11 7091602 2 BOLT, 5/16-18 x 1-1/2” Hex Flange Lock, GR 5
12 7400090 1 WELDMENT, Idler Bracket
13 7090850 3 BOLT, 3/8-16 x 3/4” Short Square Neck Carriage, GR 5 or 7091640 (3/8-16 x 1”
14 7400060 1 WELDMENT, 38” Deck Support, RH
15 7400061 1 WELDMENT, 38” Deck Support, LH
16 7090613 3 NUT, 3/8-16 Hex Flange Lock
17 7079832 1 SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
18 7090122 3 WASHER, 3/8” Flat SAE
19 7091775 3 WASHER, Special
20 7200039 1 SPACER, .380 I. D. x .895 long
21 7013847 1 RETAINER, 3/8” Bolt
22A 7034422 1 PULLEY, Flat Idler 5” x .375
22B 7100448 1 PULLEY, Flat Idler 4” x 1.24
23 7091585 2 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
24 7011201 1 NUT, 3/8-24 Hex Center lock
25 7025074 2 WASHER, .531 x 1.0 x .063 Flat
26 7400082 1 WELDMENT, Idler Arm, 38” RZT
27 7014871 1 LUBE FITTING, 3/16”
28 7042964 1 IDLER STUD (5/16-24 thread)
29 7090037 1 COTTER PIN, 3/32 x 3/4”
30 7028620 1 SPACER, .340 I.D. x .63 O.D. x .310 Thick
31 7091528 2 WASHER, 3/8” Flat
32 7091575 1 NUT, 5/16-18 Hex Center Lock, GR 5 or B, YZ
33 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
34 7091557 1 SCREW, 3/8-16 x 2-3/4” Hex Head Cap, GR 5
35 7091962 1 WASHER, 7/16” I.D. x 1-5/8” O.D. x .25 Flat
36 7091331 1 WASHER, 3/8” I.D. x 1-1/2” O.D. x .120 Flat
tionItem Qt
Note
Carriage Bolt)
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
39
TP 400-5164-C-HZ-N
Page 40
38" DECK GROUP (Final Assembly)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
40
SERIES 0 & 1
Page 41
38" DECK GROUP (Final Assembly)
p
y
Part No Descri
1 7029425 1 DISCHARGE CHUTE, 38” Deck
2 7035503 1 ROD, Mounting, Side Discharge (3/8-16 thread)
3 7091585 2 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
4 7035813 1 SPRING, Torsion-Side Discharge-38 Deck
5 7035502 1 ROD, Pivot, Side Discharge, 38 Deck
6 7091575 1 NUT, 5/16-18 Hex Center Lock, GR 5 or B, YZ
7 7091508 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
8 7091833 1 SCREW, 5/16-18 x 5/8” Cross Recessed Pan Head
9 7090188 1 WASHER, .34 x .69 x .08 Flat
10 7036543 1 TEENUT, 5/16-18 Thread
11 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5, YZ
12 7090122 8 WASHER, 3/8” Flat SAE
13 7034422 1 PULLEY, Flat Idler, 5” Dia. replaces 7072319 (PULLEY,
14 7035969 1 SPRING, Extension, 1.03 Dia. x 6.8 Long
15 7033891 1 GAGE WHEEL BRACKET, LH Rear
16 7091026 9 BOLT, 5/16-18 x 3/4” Short Square Neck Carriage, GR 5
17 7091601 9 NUT, 5/16-18 Hex Flange Lock, GR 5
18 2108765 3 SHOULDER BOLT, 3/8-16 x 5/8” GR 5 YZ replaces 7091526 (Shoulder
19 1714760 3 GAGE WHEEL 4 x 1-7/8” Offset replaces 7026122 (Wheel, 1-1/2”
20 7091585 3 NUT, 3/8-16 Hex Center Lock replaces 7090289 (Hex Center
21 7300269 1 BRACKET, Front Gage Wheel (Cardinal Red) was 7033756 (raw part)
22 7300243 1 BRACKET, Right Front Gage Wheel (Cardinal Red) was 7035494 (raw part)
23 7100691 1 BELT, A Section, Effective Length 114” replaces 1718017
tionItem Qt
Note
Flat Idler, 3-1/4” Dia.)
Bolt, 3/8-24 thread)
offset)
Lock Nut, 3/8-24)
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
41
TP 400-5164-C-HZ-N
Page 42
38" DECK SPINDLE
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
42
SERIES 0 & 1
Page 43
38" DECK SPINDLE
p
y
Part No Descri
1 7012491 2 * RING, 1-3/4” External Retaining Ring
2 7013313 2 * BALL BEARING, 3/4” I.D.
3 7059378 1 * WELDMENT, 38 Spindle Housing
4 7010817 1 * FITTING, Lube, Press-In (for .187 dia. Hole)
5 7072537 1 * SHAFT, Spindle (7.155” long)
6 7072109 1 * WASHER, Spindle Blade
7 7042998 1 * BLADE, 19.64 (38” Deck)
8 7024467 2 * WASHER, Bellville 9/16 x 1-3/4”
9 7091633 1 * NUT, 9/16-18 Hex, GR B
tionItem Qt
Note
Footnotes:
NOTE: * These parts make up 7059377, Spindle Assembly.
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
43
TP 400-5164-C-HZ-N
Page 44
42" DECK GROUP (Sub-Assembly)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
44
SERIES 0 & 1
Page 45
42" DECK GROUP (Sub-Assembly)
p
y
Part No Descri
7500021 1 SUB-ASSY, 42” Deck w/Spindles includes 18 items below
1 7400009 1 WELDMENT, 42” Deck
2 7059723 2 ASSEMBLY, Spindle Brake see 42” Deck Spindle pages
3 7027198 15 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 5
4 7091619 17 NUT, 3/8-16 Hex Flange Lock
5 7091640 4 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5, YZ
6 7033366 2 SPINDLE BRACE
7 7051747 2 ASSEMBLY, Spindle Lock w/strux nut
8 7044651 1 WELDMENT, Stationary Idler 42”
9 7090289 1 NUT, 3/8-24 Hex Center Lock
10 7090122 1 WASHER, 3/8” Flat SAE
11 7025074 2 WASHER, .531 x 1.0 x .063 Flat
12 7400083 1 WELDMENT, Idler Arm, 38” RZT (Cardinal Red)
13 7014871 1 LUBE FITTING, 3/16” or 7010817
14 7091526 1 SHOULDER BOLT, 3/8-24 x 5/8” YZ 1.530” long shoulder
15 7090872 1 BOLT,1/4-20 x 1-1/8” Hex Flange Lock, GR 5
16 7010916 1 SPACER, .265 I.D. x .375 O.D. x .300 thick
17 7092126 2 NUT 1/4-20 Hex Center Lock, GR 5 YZ
18 7014241 5 WASHER, .27 x 1.0 x .065 Flat
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
45
TP 400-5164-C-HZ-N
Page 46
42" DECK GROUP (Final Assembly)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
46
SERIES 0 & 1
Page 47
42" DECK GROUP (Final Assembly)
p
y
Part No Descri
1 7500021 1 SUB-ASSY, 42” Deck w/Spindles Ref. Sub-Assembly pages
2 7035969 1 SPRING, Extension, 1.03 Dia. x 6.8 Long
3 7035835 4 POST, Anti-Scalp
4 7091585 6 NUT, 3/8-16 Hex Center Lock, GR 5 or B, YZ
5 1714760 4 WHEEL, GAGE 3.92 X 1.87 replaces 7029264
6 2108765 4 BOLT, SHOULDER (3/8-16 thread) replaces 7029265
7 7100419 1 42” BELT, A Section, 119.25 Effective Length
8 7091328 8 SCREW, 3/8-16 x 1-1/4” Hex Head Cap, GR 5 YZ
9 7091619 8 NUT, 3/8-16 Hex Flange Lock
10 7091303 2 BOLT, 5/16-18 x 1” Short Square Neck Carriage, GR 5
11 7500185 1 ASSEMBLY, 42” Chute & Decal Cardinal Red Chute 7400116
12 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
13 7023606 2 VINYL CAP
14 7090799 2 BOLT, 5/16-18 x 5/8” Short Square Neck Carriage, GR 5
15 7011791 2 BOLT RETAINER, 5/16” Black
16 7091315 2 WASHER, 5/16” Split Lock
17 7091537 2 WING LOCKNUT, 5/16-18- YZ
18 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5 YZ or 7091553 (1-3/4” long)
19 7018574 1 PULLEY, Flat Idler 4-1/8” Dia.
20 7090122 5 WASHER, 3/8” Flat SAE
21 7091553 1 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5 YZ
22 7075707 1 PULLEY, Flat Idler (4.00 O.D.)
tionItem Qt
Note
plus decal 7013010
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
47
TP 400-5164-C-HZ-N
Page 48
42" DECK SPINDLE
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
48
SERIES 0 & 1
Page 49
42" DECK SPINDLE
p
y
Part No Descri
1 7074467 1 NUT, 3/4-16 Hex Jam, GR 8
2 7014407 1 *WASHER, Spindle (Special)
3 7036437 1 PULLEY, 5-1/4” O.D. w/hub
4 7012491 2 *RING, 1.85” Internal Retaining
5 7013313 2 *BEARING, Spindle
6 7027668 1 *SHAFT, Blade Spindle (6.500 overall length)
7 7047917 1 *WELDMENT, Spindle Housing
8 7032294 1 *BLADE HOLDER
9 7026691 1 BLADE, 21” Standard Lift
10 7012063 2 WASHER, Cone
11 7090824 2 SCREW, 3/8-24 x 1-1/4” Hex Head Cap, GR 5
12 7010817 1 *LUBE FITTING, 3/16” Press-In
tionItem Qt
Note
Footnotes:
*NOTE: These parts make up 7059723, Spindle Assembly.
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
49
TP 400-5164-C-HZ-N
Page 50
ELECTRICAL GROUP
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
50
SERIES 0 & 1
Page 51
ELECTRICAL GROUP
p
y
Part No Descri
1 7075622 1 SOLENOID - Super Trombetta- 2 Terminal
2 7027230 2 SCREW, 1/4-20 x 1” Hex Head Cap, GR 5
3 7091584 6 NUT, 1/4-20 Hex Flange Lock, GR 5
4 7073090 1 12 VOLT DC POWER OUTLET
5 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
6 7100326 1 HOUR METER, Inductive
7 7075132 1 SWITCH, PTO, Yellow
8 1722611 1 PLUG, Plastic Black
9 7023354 1 SWITCH, Seat (NC)
10 7023355 2 SWITCH- DPDT (NC/NO) (Grey)
11 7100309 1 BATTERY BRACKET
12 7100308 1 BATTERY HOLD DOWN
13 7026343 1 SWITCH, Ignition-Afterfire Solenoid includes set of keys
14 7023787 1 MACHINERY BUSHING
15 7023506 1 BEZEL
16 7091294 4 WASHER, .28 x .63 x .06 Flat, GR 5
17 7090372 3 NUT, 1/4-20 Hex Center Lock, GR 5 or B
18 7090072 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR 5
19 7100449 1 BATTERY, 12 VOLT, 230 CCA
20 7016132 1 SPACER, .65 x .88 x .10
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
51
TP 400-5164-C-HZ-N
Page 52
WIRING HARNESS
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
52
SERIES 0 & 1
Page 53
WIRING HARNESS
p
y
Part No Descri
1 7100306 1 WIRING HARNESS, Briggs RZT
2 7100307 1 CABLE, Battery Positive RZT, Red 20” #6 AWG
3 7100324 1 WIRING HARNESS, Hour Meter, RZT
4 7042956 2 WIRE, Negative, #8 AWG 14”
4 7100636 1 WIRE, Negative, #8 AWG 20”
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
53
TP 400-5164-C-HZ-N
Page 54
WIRING SCHEMATIC (Briggs Engine)
Manual No. 7006460 RZT TWIN STICK HYDRO DRIVE 250 Z
TP 400-5164-C-HZ-N
54
SERIES 0 & 1
Page 55
WIRING SCHEMATIC (Briggs Engine)
p
y
Part No Descri
7100306 1 WIRING HARNESS, Briggs 18 & 20 HP
tionItem Qt
Note
Footnotes:
Manual No. 7006460RZT TWIN STICK HYDRO DRIVE 250 Z
SERIES 0 & 1
55
TP 400-5164-C-HZ-N
Page 56
Page 57
Page 58
Parts Manual fo
r
Z
RZT TWIN STICK HYDRO DRIVE 250
38" & 42"
SERIES 0 & 1
IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY
OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS
Briggs & Startton Yard Power Products Group
Copyright © 2007
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
Revision C,
McDonough, GA, 30253 U.S.A.
10/30/2007
Manual No. 7006460
TP 400-5164-C-HZ-N
Loading...