Snapper P215517HC, RP2167517BV, R2167517BV, WP216517BV, P215517BVE User Manual

...

Parts Manual fo

21" STEEL DECK WALK BEHIND MOWERS

SERIES 17

PUSH MODELS PROPELLED

MODELS

216517B P215517HC

2167517BV P216517B

R215517HC P2167517BV

R2167517BV P2167517BVE

P217017BV

RP215517HC

RP2167517BV

RP217017BV

RP2167517BVE

RP217017BVE

WP2167517BV

WP216517BV

WRP216517BE

FRP2167517BV

EP2167517BV

EP217017BV

ERP2167517BV

ERP217017BV

EFRP2167517BV

WRPS216517B

WRPS216517BE

Revision 4,

McDonough, GA, 30253 U.S.A.

1/16/2006

Manual No. 7006136

TP 400-5002-4-WB-N

PAGE GROUP

8 12 14 16 18 20 22 24 28 30 32 34 36 38 40 42 44 46 48 50 52

HANDLES & CONTROLS CUTTING DECK, BLADES FRONT WHEEL BRACKET SWIVEL CASTER ASSEMBLY REAR WHEEL BRACKETS, LATCHES FRONT WHEELS FRONT WHEELS - SWIVEL MODEL REAR WHEELS DRIVE SYSTEM SELF-PROPELLED PT.1 TRANSMISSION (DIFFERENTIAL) THROTTLE CONTROLS KIT, MUFFLER DEFLECTOR ENGINE SPECIFICATIONS SIDE CHUTE, ADAPTER GRASS BAG ACCESSORY DECALS PT. 1 DECALS PT. 2 SNAPPERIZER ACCESSORY THATCHERIZER ACCESSORY RECYCLING KITS ACCESSORY ELECTRIC START COMPONENTS WIRING SCHEMATIC

Table Of Content

SERIES 17

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

TP 400-5002-4-WB-N

HANDLES & CONTROLS

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

HANDLES & CONTROLS

Part No Descri

1 7074254 1 HANDLE, Upper Was 72931 (used on Push

-- 7074254 1 HANDLE, Upper used on Self-Propelled 2 7036350 1 HANDLE, Middle- 1990 used on All 3 7046502 1 HANDLE, Lower Left Hand used on All 4 7035342 1 HANDLE, Lower Right Hand used on All 5 7047011 1 BAIL, Blade Control used on All 6 7033904 1 CLIP, Blade Control used on 2002 Models & Earlier

-- 7034872 1 CLIP, Blade Control used on 2003 Models & Later 7 7072933 1 CABLE, Blade Control (49-1/4” long) used on 2002 Models & Earlier

-- 7074868 1 CABLE, Blade Control (46-15/16” long) used on 2003 Models & Later

-- 7074830 1 CABLE, Blade Control (49” long) used on Honda 2003 Models &

8 7032826 1 HANDLE, Wheel Drive used on Self-Propelled 9 7014307 1 GRIP, Wheel Drive Handle used on Self-Propelled

-- 7029775 1 GRIP, Wheel Drive Handle used on European Models 10 7072932 1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled 11 7012121 1 COVER, Vinyl used on Self-Propelled 12 7012122 1 SPRING, Clutch used on Self-Propelled 13 7038478 1 SECTOR, Speed used on all other Self-Propelled

14 7024641 3 WIRE TIE, 1.29” Long (Black) used on Self-Propelled 15 7012093 1 SPRING, Speed Control used on Self-Propelled 16 7090188 1 WASHER, 3/8” Flat used on Self-Propelled 17 7023801 1 GRIP, Speed Control Handle used on all other Self-Propelled

18 7032830 1 ANCHOR, Speed Control used on all other Self-Propelled

19 7032408 1 GUIDE, Lower V-Belt used on Self-Propelled 20 7023790 1 ROD, Transfer used on Self-Propelled

20A 7051698 1 ASSEMBLY, Transfer Rod used on European Models

21 7010937 1 CLIP, Transfer Rod 1/4” used on Self-Propelled 22 7090895 1 TEE-NUT, 5/16-18 used on Self-Propelled 23 7012114 1 BUSHING, Differential used on Self-Propelled 24 7090595 1 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All 25 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All 26 7090799 1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was 91026 (used on All) 27 7091601 10 NUT, 5/16-18 Hex Flange Lock GR5 Was 91070 (used on All) 28 7091606 1 NUT, 5/16-24 Hex Center Lock GR5 Was 91074 (used on All) 29 7023813 1 CLIP, Cable/Wiring used on All 30 7091740 4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 Was 91189 (used on All) 31 7035744 4 T-KNOB, 5/16-18 (BLACK) used on All

tionItem Qt

Note

Models)

Later

models

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

HANDLES & CONTROLS

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

HANDLES & CONTROLS

Part No Descri

32 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 used on All 33 7090053 3 WASHER, 1/4” Internal Tooth Lock Was 91023 (used on All) 34 7091576 3 NUT, 1/4-20 Hex GR5 or B Was 91100 (used on All) 35 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on All 36 7014343 4 BUSHING used on All 37 7023792 1 PIN, 1/4” x 1-1/2” (for clutch handle) used on Self-Propelled 38 7091020 1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled 39 7024211 1 DECAL, Blade Control (Left Hand Side) used on all (except Euro)

-- 7029782 1 DECAL, Blade Control (Left Hand Side) used on European

-- 7029785 1 DECAL, Handle International Warning used on European 40 7026141 1 GUIDE, Rope used on All 41 7075634 1 FOAM GRIP, .84 I.D. x 11” long Was 73115

-- 7075634 1 FOAM GRIP, .84 I.D. x 12” long 42 7024087 1 DECAL, Speed Select used on Self-Propelled (except

-- 7029783 1 DECAL, Speed Select (Euro) used on Self-Propelled (Euro) 43 7023153 1 CLAMP, Casing used on All 44 7090391 4 WASHER, 5/16” Internal Tooth Lock used on All 45 7090545 1 SCREW, 5/16-24 x 1-1/2” Round Hd. Machine, GR5 used on All 46 7022779 1 GUIDE, Rope used on All 47 7074255 1 LEVER, Speed Control used on Self-Propelled 48 7046465 1 GUIDE, Rope used on Self-Propelled 49 7076978 1 NUT, 1/4-20 Hex GR5 or B used on Self-Propelled 50 7012080 1 CABLE-TIE, 7” used on Self-Propelled 52 7023154 1 SCREW, #10-32 x 5/8” Hex Head Self-Tap used on All 51 7079577 1 SCREW, 1/4-20 x 1-1/2” Hex Head Cap, GR5 used on Self-Propelled 53 7024649 1 WIRE TIE, 11” Long (Black) used on Self-Propelled

-- 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on Self-Propelled 54 7026219 1 CLAMP, 7/8” Double Cable used on Self-Propelled 56 7072023 1 CONTROL, Swivel Wheel Lock Cable 56.5" used on Swivel Wheel

tionItem Qt

Note

Euro)

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

CUTTING DECK, BLADES

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

CUTTING DECK, BLADES

Part No Descri

1 7057663 1 DECK, 21” Mower (“HV” deck w/decals)

-- 7058540 1 DECK, 21” Mower (Baffle Type deck w/decals) used on “FRP” & “EFRP” Air

-- 7057884 1 DECK, 21” Mower (“M” deck w/decals)

-- 7074949 1 DECK, 21” Mower (Swivvel wheel "M" deck w/o decals)

2 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR5 Was 90585 3 7090731 10 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5 4 7091169 1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage GR5 5 7090324 3 SCREW, 3/8-16 x 1” Self-Tap (engine mounting screws) 6 7046780 2 PLUG, Hole 7 7090534 1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models 8 7090702 1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock used on Euro models

9 7013320 1 BUSHING used on Euro models 10 7033863 1 COVER, Belt used on Euro models 11 7031961 2 WASHER, 7/16” Flat used on Euro models 12 7090483 1 SCREW, 3/8-24 x 1-3/4 Hex Head Cap GR5 13 7012063 2 WASHER, 3/8” I.D. Cone 14 7019795 1 BLADE, Cutter (European) used on Euro models

14A 7017168 1 BLADE, Cutter (Mulching) 14B 7026691 1 BLADE, Cutter (Standard Lift) 14C 7026407 1 BLADE, 21” Ninja (Quad Edge)

15 7015626 1 HUB, Blade Drive 25mm used on Briggs Models

-- 7012927 1 HUB, Blade Drive 7/8” used on Honda Models

16 7015894 1 KEY, Woodruff # 605 used on Briggs Models

-- 7091214 1 KEY, Hi-Pro #HP506 used on Briggs Models

-- 7010783 1 KEY, Woodruff #505 Hi-Pro used on Honda Models 17 7090201 1 SCREW, 5/16-18 x 5/16” Hex Socket Set 18 7015780 1 PULLEY, Engine (25mm I.D. x 2-1/8” O.D.) used on Briggs Models

-- 7021764 1 PULLEY, Engine (7/8” I.D. x 2-1/8” O.D.) used on Honda Models 19 7031961 1 WASHER, 7/16” Flat 20 7041400 1 WELDMENT, Fender used on Euro models 21 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 90001 (only one shown) 22 7011791 2 RETAINER, 5/16” Bolt (only one shown) 23 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070

-- 7060785 1 KIT, Air Lift (Includes 4 items below) 24 7032558 2 LIFT, Air 25 7090391 4 WASHER, 5/16” Internal Tooth Lock 26 7091297 4 NUT, 5/16-24 Hex, GR5 Was 90223

tionItem Qt

Note

Models only

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

CUTTING DECK, BLADES

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

CUTTING DECK, BLADES

Part No Descri

27 7090228 4 SCREW, 5/16-24 x 21/32” Machine 28 7090951 2 NUT, 5/16-18 Hex Center Lock 29 7029193 1 DECAL, Front Baffle 30 7072426 1 BAFFLE, Front used on “FRP” & “EFRP” Air

31 7036463 1 DECAL, Front Baffle 32 7090316 2 BOLT, 5/16-18 x 3/4” Carriage, GR5 33 7090189 2 WASHER, 5/16” Internal/External Tooth Lock 34 7024085 2 WINGNUT, 5/16-18 Nyloc 35 7091076 1 WASHER, 5/16” Flat 36 7044770 1 SPACER, 1/16” Thick, Blade Hub 37 7074568 1 BAFFLE, Belt 38 7046471 3 PLUG, 5/16” Square Hole used on Push only 39 7045264 3 PLUG, 5/16” Round Hole Qty 3 on Push; Qty 2 on Self-

40 7091122 4 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539 41 7046720 1 DECAL, Warning Chute/Deflector

tionItem Qt

Note

Models only

Propelled

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

FRONT WHEEL BRACKET

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

FRONT WHEEL BRACKET

Part No Descri

1 7051886 1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A &

-- 7051885 1 ASSEMBLY, Left Wheel Arm (Consists of items 2, 3, 4, 5B &

2 7015761 2 BOLT, 5/16-18 Hex Washer Face Shoulder 3 7012325 2 LATCH, Height

4 7027702 2 GRIP, Latch 5A 7031017 1 ARM, Right Wheel (Round Hole) 5B 7031016 1 ARM, Left Wheel (Square Hole) not shown

6 7011791 2 RETAINER, 5/16” Bolt (Black)

7 7091601 2 NUT, 5/16-18 Hex Flange Lock Was 91070

8 7074702 1 WELDMENT, Front Wheel Bracket Was 41770, Used on 2002

-- 7074702 1 WELDMENT, Front Wheel Bracket used on 2003 Model Year and

9 7021119 1 AXLE

tionItem Qt

Note

Model Year and Earlier

Later

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

SWIVEL CASTER ASSEMBLY

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

SWIVEL CASTER ASSEMBLY

Part No Descri

1 7057782 1 WELDMENT, Front Bracket

2 7079577 1 SCREW, 1/4-20 x 1-1/2” Hex Cap

3 7090372 1 NUT, 1/4-20 Hex Lock

4 7072244 1 BRACKET, Swivel Lock

5 7046668 1 SPRING, Torsion

6 7090505 1 BOLT, 1/4-20 x 2” Hex

7 7027344 4 WASHER, 41/64” Flat Was 15992

8 7046628 4 BUSHING, 5/8” Nylon

9 7013864 2 LUBE FITTING, Straight (press-fit for .187 dia. Hole) 10 7076978 1 NUT, 1/4-20 Hex Lock 11 7014106 2 PIN, 1/4 x 1-3/4” Roll 12 7072229 1 WELDMENT, L.H. Swivel Bracket

7072230 1 WELDMENT, R.H. Swivel Bracket Was 57789 (Not Shown)

13 7072023 1 CONTROL, Swivel Wheel Lock Cable 56.5”

tionItem Qt

Note

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

REAR WHEEL BRACKETS, LATCHES

Manual No. 7006136 21" STEEL DECK WALK BEHIND MOWERS TP 400-5002-4-WB-N

SERIES 17

REAR WHEEL BRACKETS, LATCHES

Part No Descri

1 7012312 2 BALL BEARING, 9/16” I.D.

2 7091012 3 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx)

3 7035717 2 LATCH, Height Adjusting (Long)

4 7091576 1 NUT, 1/4-20 Hex Was 90063

5 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR5 Was 91070

6 7054228 1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.

7 7054229 1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.

8 7054246 1 ASSEMBLY, Wheel Arm (Right Rear) Was 54230 (Self-Propelled

9 7054247 1 ASSEMBLY, Wheel Arm (Left Rear) Was 54231 (Self-Propelled

10 7033776 1 ARM, Round Axle End, Right Rear (Round hole) used on Push models 11 7033775 1 ARM, Square Axle End, Left Rear (Square hole) used on Push models 12 7032722 1 ARM, Wheel, Right Rear used on Self-Propelled models 13 7032723 1 ARM, Wheel, Left Rear used on Self-Propelled models 14 7011078 2 BOLT, 5/16-18 x 1” Shoulder 15 7011791 2 RETAINER, 5/16” Bolt 16 7027702 2 GRIP, Latch 17 7033494 1 BRACKET, Right Rear Wheel 18 7033495 1 BRACKET, Left Rear Wheel 19 7021119 1 AXLE Rear axle on Push Models;

20 7035741 1 GUARD, Rear Foot used on Push models 21 7029008 1 GUARD, Rear Foot used on Self-Propelled models

-- 7017010 1 GUARD, Rear Foot used on Euro Self-Propelled

22 7023791 1 RING, Split (Black) used on Self-Propelled models 23 7012616 1 SUPPORT, Foot Guard used on Self-Propelled models 24 7091604 1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 Was 90005 (used on Self-

25 7090053 1 WASHER, 1/4” Internal Tooth Lock Was 91023 26 7090731 2 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5

tionItem Qt

Note

items 3, 10, 14, 15 & 16)

items 3, 11, 14, 15 & 16)

models)(Incl. 1, 2, 3, 12, 14, 15 & 16)

Models)(Includes 1, 2, 3, 13, 15, & 16)

Front axle on All Models

(except European)

models

Propelled models)

Footnotes:

Manual No. 700613621" STEEL DECK WALK BEHIND MOWERS

SERIES 17

TP 400-5002-4-WB-N

+ 39 hidden pages